- 22 Feb, 2024 6 commits
-
-
Jeremy Kerr authored
In our test skb creation functions, we're not setting up the net and device data. This doesn't matter at the moment, but we will want to add support for distinct net IDs in future. Set the ->net identifier on the test MCTP device, and ensure that test skbs are set up with the correct device-related data on creation. Create a helper for setting skb->dev and mctp_skb_cb->net. We have a few cases where we're calling __mctp_cb() to initialise the cb (which we need for the above) separately, so integrate this into the skb creation helpers. Signed-off-by:
Jeremy Kerr <jk@codeconstruct.com.au> Signed-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Jeremy Kerr authored
We may have an ANY address in either the local or peer address of a sk_key, and may want to match on an incoming daddr or saddr being ANY. Do this by altering the conflicting-tag lookup to also accept ANY as the local/peer address. We don't want mctp_address_matches to match on the requested EID being ANY, as that is a specific lookup case on packet input. Reported-by:
Eric Chuang <echuang@google.com> Reported-by:
Anthony <anthonyhkf@google.com> Signed-off-by:
-
Jeremy Kerr authored
We could do with a little more comment on where MCTP_ADDR_ANY will match in the key allocations. Signed-off-by:
-
Jeremy Kerr authored
We have a double-swap of local and peer addresses in mctp_alloc_local_tag; the arguments in both call sites are swapped, but there is also a swap in the implementation of alloc_local_tag. This is opaque because we're using source/dest address references, which don't match the local/peer semantics. Avoid this confusion by naming the arguments as 'local' and 'peer', and remove the double swap. The calling order now matches mctp_key_alloc. Signed-off-by:
-
Samuel Thibault authored
The existing documentation was not telling that one has to create a PPP channel and a PPP interface to get PPPoL2TP data offloading working. Also, tunnel switching was not mentioned, so that people were thinking it was not supported, while it actually is. Signed-off-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Acked-by:
Tom Parkin <tparkin@katalix.com> Link: https://lore.kernel.org/r/20240217211425.qj576u3jmaa6yidf@beginSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Paolo Abeni authored
We want to re-organize the struct sock layout. The sk_peek_off field location is problematic, as most protocols want it in the RX read area, while UDP wants it on a cacheline different from sk_receive_queue. Create a local (inside udp_sock) copy of the 'peek offset is enabled' flag and place it inside the same cacheline of reader_queue. Check such flag before reading sk_peek_off. This will save potential false sharing and cache misses in the fast-path. Tested under UDP flood with small packets. The struct sock layout update causes a 4% performance drop, and this patch restores completely the original tput. Signed-off-by:
Eric Dumazet <edumazet@google.com> Reviewed-by:
Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/67ab679c15fbf49fa05b3ffe05d91c47ab84f147.1708426665.git.pabeni@redhat.comSigned-off-by:
-
- 21 Feb, 2024 34 commits
-
-
Jakub Kicinski authored
Dimitri Fedrau says: ==================== net: phy: marvell-88q2xxx: add driver for the Marvell 88Q2220 PHY ==================== Link: https://lore.kernel.org/r/20240218075753.18067-1-dima.fedrau@gmail.comSigned-off-by:
-
Dimitri Fedrau authored
Move interrupt configuration from mv88q222x_revb0_config_init to mv88q2xxx_config_init. Same register and bits are used for the 88q2xxx devices. Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Stefan Eichenberger <eichest@gmail.com> Signed-off-by:
Dimitri Fedrau <dima.fedrau@gmail.com> Link: https://lore.kernel.org/r/20240218075753.18067-15-dima.fedrau@gmail.comSigned-off-by:
-
Dimitri Fedrau authored
Remove assignment of phydev->pma_extable in mv88q222x_revb0_config_init. It is already done in mv88q2xxx_config_init, just call mv88q2xxx_config_init. Reviewed-by:
-
Dimitri Fedrau authored
mv88q2xxx_config_init calls genphy_c45_read_pma which is done by mv88q2xxx_read_status, it calls also mv88q2xxx_config_aneg which is also called by the PHY state machine. Let the PHY state machine handle the phydriver ops in their intendend way. Reviewed-by:
-
Dimitri Fedrau authored
Switch to mv88q2xxx_config_aneg for Marvell 88Q2220 devices and remove the mv88q222x_config_aneg function which is basically a copy of the mv88q2xxx_config_aneg function. Reviewed-by:
-
Dimitri Fedrau authored
Marvell 88Q2xxx devices follow the same scheme, after configuration they need a soft reset. Soft resets differ between devices, so we use the .soft_reset callback instead of creating .config_aneg callbacks for each device. Reviewed-by:
-
Dimitri Fedrau authored
Add cable test support for Marvell 88Q222x devices. Reported distance granularity is 1m. 1m cable, open: Cable test started for device eth0. Cable test completed for device eth0. Pair A code Open Circuit Pair A, fault length: 1.00m 1m cable, shorted: Cable test started for device eth0. Cable test completed for device eth0. Pair A code Short within Pair Pair A, fault length: 1.00m 6m cable, open: Cable test started for device eth0. Cable test completed for device eth0. Pair A code Open Circuit Pair A, fault length: 6.00m 6m cable, shorted: Cable test started for device eth0. Cable test completed for device eth0. Pair A code Short within Pair Pair A, fault length: 6.00m Signed-off-by:
-
Dimitri Fedrau authored
Marvell 88q2xxx devices have an inbuilt temperature sensor. Add hwmon support for this sensor. Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Dimitri Fedrau authored
Add suspend/resume ops for Marvell 88Q2xxx devices. Reviewed-by:
-
Dimitri Fedrau authored
Added .config_intr and .handle_interrupt callbacks. Whenever the link goes up or down an interrupt will be triggered. Interrupts are configured separately for 100/1000BASET1. Reviewed-by:
-
Dimitri Fedrau authored
Add a driver for the Marvell 88Q2220. This driver allows to detect the link, switch between 100BASE-T1 and 1000BASE-T1 and switch between master and slave mode. Autonegotiation is supported. Reviewed-by:
Gregor Herburger <gregor.herburger@ew.tq-group.com> Signed-off-by:
-
Dimitri Fedrau authored
Rename mv88q2xxxx_get_sqi to mv88q2xxx_get_sqi and mv88q2xxxx_get_sqi_max to mv88q2xxx_get_sqi_max. Fix linebreaks and use everywhere hexadecimal numbers written with lowercase letters instead of mixing it up. Reviewed-by:
-
Dimitri Fedrau authored
Set 100BT1 and 1000BT1 linkmode advertisement bits to adv_l_mask to enable detection. Reviewed-by:
-
Dimitri Fedrau authored
Extend helper functions mii_t1_adv_m_mod_linkmode_t and linkmode_adv_to_mii_t1_adv_m_t to support 100BT1 and 1000BT1 linkmode advertisements. Reviewed-by:
-
Dimitri Fedrau authored
Added constants for advertising 100BT1 and 1000BT1 in register BASE-T1 auto-negotiation advertisement register [31:16] (Register 7.515) Reviewed-by:
-
Raju Lakkaraju authored
Fill in the possible_interfaces member. GPY21x phys support the SGMII and 2500base-X interfaces Signed-off-by:
Raju Lakkaraju <Raju.Lakkaraju@microchip.com> Link: https://lore.kernel.org/r/20240216054435.22380-1-Raju.Lakkaraju@microchip.comSigned-off-by:
-
David S. Miller authored
Florian Fainelli says: ==================== Rework GENET MDIO controller clocking This patch series reworks the way that we manage the GENET MDIO controller clocks around I/O accesses. During testing with a fully modular build where bcmgenet, mdio-bcm-unimac, and the Broadcom PHY driver (broadcom) are all loaded as modules, with no particular care being taken to order them to mimize deferred probing the following bus error was obtained: [ 4.344831] printk: console [ttyS0] enabled [ 4.351102] 840d000.serial: ttyS1 at MMIO 0x840d000 (irq = 29, base_baud = 5062500) is a Broadcom BCM7271 UART [ 4.363110] 840e000.serial: ttyS2 at MMIO 0x840e000 (irq = 30, base_baud = 5062500) is a Broadcom BCM7271 UART [ 4.387392] iproc-rng200 8402000.rng: hwrng registered [ 4.398012] Consider using thermal netlink events interface [ 4.403717] brcmstb_thermal a581500.thermal: registered AVS TMON of-sensor driver [ 4.440085] bcmgenet 8f00000.ethernet: GENET 5.0 EPHY: 0x0000 [ 4.482526] unimac-mdio unimac-mdio.0: Broadcom UniMAC MDIO bus [ 4.514019] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.551304] SError Interrupt on CPU2, code 0x00000000bf000002 -- SError [ 4.551324] CPU: 2 PID: 8 Comm: kworker/u8:0 Not tainted 6.1.53-0.1pre-g5a26d98e908c #2 [ 4.551330] Hardware name: BCM972180HB_V20 (DT) [ 4.551336] Workqueue: events_unbound deferred_probe_work_func [ 4.551363] pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 4.551368] pc : el1_abort+0x2c/0x58 [ 4.551376] lr : el1_abort+0x20/0x58 [ 4.551379] sp : ffffffc00a383960 [ 4.551380] x29: ffffffc00a383960 x28: ffffff80029fd780 x27: 0000000000000000 [ 4.551385] x26: 0000000000000000 x25: ffffff8002839005 x24: ffffffc00a1f9bd0 [ 4.551390] x23: 0000000040000005 x22: ffffffc000a48084 x21: ffffffc00a3dde14 [ 4.551394] x20: 0000000096000210 x19: ffffffc00a3839a0 x18: 0000000000000579 [ 4.551399] x17: 0000000000000000 x16: 0000000100000000 x15: ffffffc00a3838c0 [ 4.551403] x14: 000000000000000a x13: 6e69622f7273752f x12: 3a6e6962732f7273 [ 4.551408] x11: 752f3a6e69622f3a x10: 6e6962732f3d4854 x9 : ffffffc0086466a8 [ 4.551412] x8 : ffffff80049ee100 x7 : ffffff8003231938 x6 : 0000000000000000 [ 4.551416] x5 : 0000002200000000 x4 : ffffffc00a3839a0 x3 : 0000002000000000 [ 4.551420] x2 : 0000000000000025 x1 : 0000000096000210 x0 : 0000000000000000 [ 4.551429] Kernel panic - not syncing: Asynchronous SError Interrupt [ 4.551432] CPU: 2 PID: 8 Comm: kworker/u8:0 Not tainted 6.1.53-0.1pre-g5a26d98e908c #2 [ 4.551435] Hardware name: BCM972180HB_V20 (DT) [ 4.551437] Workqueue: events_unbound deferred_probe_work_func [ 4.551443] Call trace: [ 4.551445] dump_backtrace+0xe4/0x124 [ 4.551452] show_stack+0x1c/0x28 [ 4.551455] dump_stack_lvl+0x60/0x78 [ 4.551462] dump_stack+0x14/0x2c [ 4.551467] panic+0x134/0x304 [ 4.551472] nmi_panic+0x50/0x70 [ 4.551480] arm64_serror_panic+0x70/0x7c [ 4.551484] do_serror+0x2c/0x5c [ 4.551487] el1h_64_error_handler+0x2c/0x40 [ 4.551491] el1h_64_error+0x64/0x68 [ 4.551496] el1_abort+0x2c/0x58 [ 4.551499] el1h_64_sync_handler+0x8c/0xb4 [ 4.551502] el1h_64_sync+0x64/0x68 [ 4.551505] unimac_mdio_readl.isra.0+0x4/0xc [mdio_bcm_unimac] [ 4.551519] __mdiobus_read+0x2c/0x88 [ 4.551526] mdiobus_read+0x40/0x60 [ 4.551530] phy_read+0x18/0x20 [ 4.551534] bcm_phy_config_intr+0x20/0x84 [ 4.551537] phy_disable_interrupts+0x2c/0x3c [ 4.551543] phy_probe+0x80/0x1b0 [ 4.551545] really_probe+0x1b8/0x390 [ 4.551550] __driver_probe_device+0x134/0x14c [ 4.551554] driver_probe_device+0x40/0xf8 [ 4.551559] __device_attach_driver+0x108/0x11c [ 4.551563] bus_for_each_drv+0xa4/0xcc [ 4.551567] __device_attach+0xdc/0x190 [ 4.551571] device_initial_probe+0x18/0x20 [ 4.551575] bus_probe_device+0x34/0x94 [ 4.551579] deferred_probe_work_func+0xd4/0xe8 [ 4.551583] process_one_work+0x1ac/0x25c [ 4.551590] worker_thread+0x1f4/0x260 [ 4.551595] kthread+0xc0/0xd0 [ 4.551600] ret_from_fork+0x10/0x20 [ 4.551608] SMP: stopping secondary CPUs [ 4.551617] Kernel Offset: disabled [ 4.551619] CPU features: 0x00000,00c00080,0000420b [ 4.551622] Memory Limit: none [ 4.833838] ---[ end Kernel panic - not syncing: Asynchronous SError Interrupt ]--- The issue here is that we managed to probe the GENET controller, the mdio-bcm-unimac MDIO controller, but the PHY was still being held in a probe deferral state because it depended upon a GPIO controller provider not loaded yet. As soon as that provider is loaded however, the PHY continues to probe, tries to disable the interrupts, and this causes a MDIO transaction. That MDIO transaction requires I/O register accesses within the GENET's larger block, and since its clocks are turned off, the CPU gets a bus error signaled as a System Error. The patch series takes the simplest approach of keeping the clocks enabled just for the duration of the I/O accesses. This is also beneficial to other drivers like bcmasp2 which make use of the same MDIO controller driver. Changes in v2: - added missing ret assignment in the if (IS_ERR(priv->clk)) branch - added Jacob's R-by tags - corrected the commit ID being reverted in patch #3 ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
This reverts commit 1b5ea7ff ("net: bcmgenet: Ensure MDIO unregistration has clocks enabled"). This is no longer necessary now that the MDIO bus controller has a clock that it can manage around the I/O accesses. Reviewed-by:
Jacob Keller <jacob.e.keller@intel.com> Signed-off-by:
Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by:
-
Florian Fainelli authored
GENET has historically had to create a MDIO platform device for its controller and pass some auxiliary data to it, like a MDIO completion callback. Now we also pass the "main" clock to allow for the MDIO bus controller to manage that clock adequately around I/O accesses. Reviewed-by:
-
Florian Fainelli authored
Up until now we have managed not to have the mdio-bcm-unimac manage its clock except during probe and suspend/resume. This works most of the time, except where it does not. With a fully modular build, we can get into a situation whereby the GENET driver is fully registered, and so is the mdio-bcm-unimac driver, however the Ethernet PHY driver is not yet, because it depends on a resource that is not yet available (e.g.: GPIO provider). In that state, the network device is not usable yet, and so to conserve power, the GENET driver will have turned off its "main" clock which feeds its MDIO controller. When the PHY driver finally probes however, we make an access to the PHY registers to e.g.: disable interrupts, and this causes a bus error within the MDIO controller space because the MDIO controller clock(s) are turned off. To remedy that, we manage the clock around all of the I/O accesses to the hardware which are done exclusively during read, write and clock divider configuration. This ensures that the register space is accessible, and this also ensures that there are not unnecessarily elevated reference counts keeping the clocks active when the network device is administratively turned off. It would be the case with the previous way of managing the clock. Reviewed-by:
-
Simon Horman authored
Remove documentation of non-existent children field from the Kernel doc for struct framer_ops. Introduced by 82c944d0 ("net: wan: Add framer framework support") Signed-off-by:
Simon Horman <horms@kernel.org> Acked-by:
Herve Codina <herve.codina@bootlin.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-next-2024-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.9 The second "new features" pull request for v6.9. Lots of iwlwifi and stack changes this time. And naturally smaller changes to other drivers. We also twice merged wireless into wireless-next to avoid conflicts between the trees. Major changes: stack * mac80211: negotiated TTLM request support * SPP A-MSDU support * mac80211: wider bandwidth OFDMA config support iwlwifi * kunit tests * bump FW API to 89 for AX/BZ/SC devices * enable SPP A-MSDUs * support for new devices ath12k * refactoring in preparation for Multi-Link Operation (MLO) support * 1024 Block Ack window size support * provide firmware wmi logs via a trace event ath11k * 36 bit DMA mask support * support 6 GHz station power modes: Low Power Indoor (LPI), Standard Power) SP and Very Low Power (VLP) rtl8xxxu * TP-Link TL-WN823N V2 support ==================== Signed-off-by:
-
David S. Miller authored
Kunwu Chan says: ==================== net: Use KMEM_CACHE instead of kmem_cache_create As Jiri Pirko suggests, I'm using a patchset to cleanup the same issues in the 'net' module. Use the new KMEM_CACHE() macro instead of direct kmem_cache_create to simplify the creation of SLAB caches. Some cache names are changed to be the same as struct names. This change is recorded in the changelog for easy reference. It's harmless cause it's used in /proc/slabinfo to identify this cache. --- Changes in v2: - Delete a patch as Eric said in https://lore.kernel.org/all/CANn89iLkWvum6wSqSya_K+1eqnFvp=L2WLW=kAYrZTF8Ei4b7g@mail.gmail.com/ - No code changes,only add Reviewed-by tag ==================== Signed-off-by:
-
Kunwu Chan authored
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create to simplify the creation of SLAB caches. Signed-off-by:
Kunwu Chan <chentao@kylinos.cn> Reviewed-by:
Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by:
-
Kunwu Chan authored
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create to simplify the creation of SLAB caches. And change cache name from 'ip_dst_cache' to 'rtable'. Signed-off-by:
-
Kunwu Chan authored
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create to simplify the creation of SLAB caches. And change cache name from 'ip_mrt_cache' to 'mfc_cache'. Signed-off-by:
-
Kunwu Chan authored
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create to simplify the creation of SLAB caches. And change cache name from 'ip6_mrt_cache' to 'mfc6_cache'. Signed-off-by:
-
Kunwu Chan authored
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create to simplify the creation of SLAB caches. And change cache name from 'kcm_mux_cache' to 'kcm_mux', 'kcm_psock_cache' to 'kcm_psock'. Signed-off-by:
-
Breno Leitao authored
With commit 34d21de9 ("net: Move {l,t,d}stats allocation to core and convert veth & vrf"), stats allocation could be done on net core instead of this driver. With this new approach, the driver doesn't have to bother with error handling (allocation failure checking, making sure free happens in the right spot, etc). This is core responsibility now. Move dummy driver to leverage the core allocation. Suggested-by:
Breno Leitao <leitao@debian.org> Reviewed-by:
-
Heiner Kallweit authored
Make use of ethtool_adv_to_mmd_eee_adv_t() to simplify the code. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Reviewed-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Heiner Kallweit authored
The current code overwrites fields in tp->eee with unchecked data from edata, e.g. the bitmap with supported modes. ethtool properly returns the received data from get_eee() call, but we have no guarantee that other users of the ioctl set_eee() interface behave properly too. Therefore copy only fields which are actually needed. Signed-off-by:
-
David S. Miller authored
Ricardo B. Marliere says: ==================== net: constify struct device_type usage This is a simple and straight forward cleanup series that makes all device types in the net subsystem constants. This has been possible since 2011 [1] but not all occurrences were cleaned. I have been sweeping the tree to fix them all. I was not sure if I should send these squashed, but there are quite a few changes so I decided to send them separately. Please let me know if that is not desirable. [1] https://lore.kernel.org/all/1305850262-9575-5-git-send-email-gregkh@suse.de/ ==================== Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Ricardo B. Marliere <ricardo@marliere.net>
-
Ricardo B. Marliere authored
Since commit aed65af1 ("drivers: make device_type const"), the driver core can properly handle constant struct device_type. Move the hso_type variable to be a constant structure as well, placing it into read-only memory which can not be modified at runtime. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Ricardo B. Marliere authored
Since commit aed65af1 ("drivers: make device_type const"), the driver core can properly handle constant struct device_type. Move the wwan_type variable to be a constant structure as well, placing it into read-only memory which can not be modified at runtime. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by:
-
