- 11 Nov, 2008 22 commits
-
-
Frederic CAND authored
Starts encoder not only on a read call but also on a poll command. Signed-off-by:
Frederic CAND <frederic.cand@anevia.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Akinobu Mita authored
anysee_usb_mutex is initialized at every time the anysee device is probed. If the second anysee device is probed while anysee_usb_mutex is locked by the first anysee device, the mutex is broken. This patch fixes by initialize anysee_usb_mutex statically rather than initialize at probe time. Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Daniel J Blueman authored
When inadvertently hot-unplugging a WT-220U USB DVB-T receiver with 2.6.24, I was met with an oops [1]. The problem is relevant to 2.6.25/26-rc also. dvb_frontend_init() was called either from re-creation of the kdvb-fe0 thread - seems unlikely, or someone called dvb_frontend_reinitialise(), causing this path in the thread - really unlikely, as I can't find any call-site for it. Either way, quite a number of drivers call dvb_usb_generic_rw() [2] without checking the validity of the relevant member in the dvb_usb_device struct - which had changed. Having dvb_usb_generic_rw() sanity-check and fail (rather than loading from 0x120) seems reasonable defensive programming [3], in light of it being called in this way. The problem with this, is that drivers don't check the return code of the init call [4]. Does it make sense to cook a patch which allows the failure to be propagated back up, or am I missing something else? Thanks, Daniel <whoops, hot unplug> [83711.538485] dvb-usb: bulk message failed: -71 (1/0) [83711.538875] dvb-usb: bulk message failed: -71 (1/0) [83711.538899] usb 7-5: USB disconnect, address 3 [83711.538905] dvb-usb: bulk message failed: -22 (1/0) [83711.538924] dvb-usb: bulk message failed: -22 (1/0) [83711.538943] dvb-usb: bulk message failed: -22 (1/0) [83711.588979] dvb-usb: bulk message failed: -22 (1/0) [83711.589031] dvb-usb: bulk message failed: -22 (1/0) [83711.589078] dvb-usb: bulk message failed: -22 (1/0) [83711.589122] dvb-usb: bulk message failed: -22 (1/0) [83711.589167] dvb-usb: bulk message failed: -22 (1/0) [83711.639233] dvb-usb: bulk message failed: -22 (1/0) [83711.639282] dvb-usb: bulk message failed: -22 (1/0) [83711.639330] dvb-usb: bulk message failed: -22 (1/0) [83711.639374] dvb-usb: bulk message failed: -22 (1/0) [83711.639421] dvb-usb: bulk message failed: -22 (1/0) [83711.658391] dvb-usb: bulk message failed: -22 (1/0) [83768.174281] dvb-usb: bulk message failed: -22 (2/-32512) [83768.174350] Unable to handle kernel NULL pointer dereference<6>dvb-usb: WideView WT-220U PenType Receiver (Typhoon/Freecom) successfully deinitialized and disconnected. [83768.174459] at 0000000000000120 RIP: [83768.174459] [<ffffffff88339b4f>] :dvb_usb:dvb_usb_generic_rw+0x2f/0x1a0 [83768.174580] PGD 0 [83768.174643] Oops: 0000 [1] SMP [83768.174723] CPU 0 [83768.174782] Modules linked in: nfsd auth_rpcgss exportfs nfs lockd nfs_acl sunrpc af_packet xt_length ipt_tos ipt_TOS xt_CLASSIFY sch_sfq sch_htb ipt_MASQUERADE ipt_REDIRECT xt_limit xt_state xt_tcpudp iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack iptable_mangle iptable_filter ip_tables x_tables xfs sbp2 parport_pc lp parport loop ftdi_sio usbserial evdev dvb_usb_dtt200u dvb_usb dvb_core i2c_core sky2 iTCO_wdt iTCO_vendor_support snd_hda_intel shpchp snd_pcm snd_timer snd_page_alloc snd_hwdep snd pci_hotplug soundcore ipv6 button intel_agp ext3 jbd mbcache sg sd_mod ata_generic pata_acpi ahci ata_piix libata scsi_mod ohci1394 ieee1394 ehci_hcd uhci_hcd usbcore e1000 thermal processor fan fbcon tileblit font bitblit softcursor fuse [83768.176968] Pid: 5732, comm: kdvb-fe-0 Not tainted 2.6.24-16-server #1 [83768.177009] RIP: 0010:[<ffffffff88339b4f>] [<ffffffff88339b4f>] :dvb_usb:dvb_usb_generic_rw+0x2f/0x1a0 [83768.177096] RSP: 0018:ffff810021939df0 EFLAGS: 00010286 [83768.177138] RAX: ffff81003bc7cc00 RBX: 0000000000000001 RCX: 0000000000000000 [83768.177181] RDX: 0000000000000001 RSI: ffff810021939e67 RDI: 0000000000000000 [83768.177223] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 [83768.177267] R10: ffff810001009880 R11: 0000000000000001 R12: ffff81003c10b400 [83768.177311] R13: ffff81003c10b5b0 R14: ffff810021939ec0 R15: 0000000000000000 [83768.177354] FS: 0000000000000000(0000) GS:ffffffff805c3000(0000) knlGS:0000000000000000 [83768.177409] CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b [83768.177449] CR2: 0000000000000120 CR3: 0000000000201000 CR4: 00000000000006e0 [83768.177491] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [83768.177534] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [83768.177576] Process kdvb-fe-0 (pid: 5732, threadinfo ffff810021938000, task ffff81003bd1b7a0) [83768.177629] Stack: ffff81003e9b6828 0000000000000000 ffff8100378369f8 0000000000000000 [83768.177800] ffff81003bd1b7a0 ffff810037836d48 ffff81003bc7cc30 ffff81003c10b400 [83768.177943] ffff81003c10b5b0 ffff810021939ec0 ffff81003c10b5e0 ffffffff88342452 [83768.178054] Call Trace: [83768.178130] [<ffffffff88342452>] :dvb_usb_dtt200u:dtt200u_fe_init+0x22/0x30 [83768.178178] [<ffffffff88339f6a>] :dvb_usb:dvb_usb_fe_wakeup+0x3a/0x50 [83768.178229] [<ffffffff88325c41>] :dvb_core:dvb_frontend_init+0x21/0x70 [83768.178278] [<ffffffff8832746b>] :dvb_core:dvb_frontend_thread+0x8b/0x370 [83768.178329] [<ffffffff883273e0>] :dvb_core:dvb_frontend_thread+0x0/0x370 [83768.178382] [<ffffffff80253e3b>] kthread+0x4b/0x80 [83768.178427] [<ffffffff8020d198>] child_rip+0xa/0x12 [83768.178473] [<ffffffff80253df0>] kthread+0x0/0x80 [83768.178514] [<ffffffff8020d18e>] child_rip+0x0/0x12 [83768.178557] [83768.178594] [83768.178594] Code: 44 8b 87 20 01 00 00 49 89 f4 45 89 ce 45 85 c0 0f 84 ad 00 [83768.179167] RIP [<ffffffff88339b4f>] :dvb_usb:dvb_usb_generic_rw+0x2f/0x1a0 [83768.179234] RSP <ffff810021939df0> [83768.179271] CR2: 0000000000000120 [83768.179419] ---[ end trace dba8483163cb1700 ]--- Signed-off-by: -
Hans Verkuil authored
Remove the EXPERIMENTAL tag. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Hans Verkuil authored
ivtv used tvaudio in the past and at the time tvaudio required V4L1. Since tvaudio is no longer dependent on V4L1 and since ivtv actually no longer uses tvaudio at all, this is no removed from Kconfig. Without this patch ivtv won't be build if V4L1 is disabled. Signed-off-by:
-
Tobias Lorenz authored
This patch adds a recommendation to select SND_USB_AUDIO for listing and adds a documentation file for si470x. Signed-off-by:
Tobias Lorenz <tobias.lorenz@gmx.net> Signed-off-by:
-
Andy Walls authored
cx18: Disable write retries for registers that always change - part 1. Interrupt related registers will likely not read back the value we just wrote. Disable retries for these registers for now to avoid accidently discarding interrupts. More intelligent read back verification criteria are needed for these and other registers (e.g. GPIO line registers), which will be addressed in subsequent changes. Signed-off-by:
Andy Walls <awalls@radix.net> Signed-off-by:
-
Jean Delvare authored
* Apparently the author of the saa7110 driver was confused by the number of outputs returned by DECODER_GET_CAPABILITIES. Of course a decoder chip has no analog ouputs, but it must have at least one digital output. * Fix an off-by-one error when checking the input value of DECODER_SET_INPUT. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Rafael Diniz authored
Attached is a patch that updates the cx88 documentation to add the fact the closed caption works for at least NTSC capture. ps: I also updated the wiki at: http://www.linuxtv.org/v4lwiki/index.php/Text_capture#cx88_devicesSigned-off-by:
Rafael Diniz <diniz@wimobilis.com.br> Signed-off-by:
-
Rafael Diniz authored
The attached patch fix VBI support cx88 card. I'm running a capture for hours, getting the closed caption from it[1], and it's working perfect - the output is the same of a bttv card. Please apply this patch as soon as possible. [1] - using zvbi-ntsc-cc of zvbi project. Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
Costantino Leandro <lcostantino@gmail.com> Signed-off-by:
Erik Andrén <erik.andren@gmail.com> Signed-off-by:
Frank Zago <frank@zago.net> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Jean-Francois Moine <moinejf@free.fr> Signed-off-by:
-
Thierry MERLE authored
config\tDVB_USB_CINERGY_T2 causes the make_kconfig.pl to forget to enable by default the compilation of cinergyT2 module. Signed-off-by:
Thierry MERLE <thierry.merle@free.fr> Signed-off-by:
-
Matthias Schwarzott authored
There already is an report at kernel bugzilla about this issue: http://bugzilla.kernel.org/show_bug.cgi?id=9455 When enabling extra checks for the i2c-bus of cx88 based cards by loading i2c_algo_bit with bit_test=1 this may trigger an oops when loading cx88_dvb. This is caused by the extra check code that detects that the sda-line is stuck high and thus does not register the i2c-bus. cx88-dvb however does not check if the i2c-bus is valid and just uses core->i2c_adap to attach dvb frontend modules. This leads to an oops at the first call to i2c_transfer: $ modprobe i2c_algo_bit bit_test=1 $ modprobe cx8802 cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded cx88[0]: quirk: PCIPCI_NATOMA -- set TBFX cx88[0]: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37,autodetected], frontend(s): 1 cx88[0]: TV tuner type 4, Radio tuner type -1 cx88[0]: SDA stuck high! cx88[0]: i2c register FAILED input: cx88 IR (Hauppauge Nova-S-Plus as /class/input/input5 cx88[0]/2: cx2388x 8802 Driver Manager cx88-mpeg driver manager 0000:00:10.2: enabling device (0154 -> 0156) cx88-mpeg driver manager 0000:00:10.2: PCI INT A -> Link[LNKD] -> GSI 9 (level, low) -> IRQ 9 cx88[0]/2: found at 0000:00:10.2, rev: 5, irq: 9, latency: 64, mmio: 0xfb000000 cx8802_probe() allocating 1 frontend(s) cx88/2: cx2388x dvb driver version 0.0.6 loaded cx88/2: registering cx8802 driver, type: dvb access: shared cx88[0]/2: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37] cx88[0]/2: cx2388x based DVB/ATSC card BUG: unable to handle kernel NULL pointer dereference at 00000000 IP: [<e084d4ef>] :i2c_core:i2c_transfer+0x1f/0x80 *pde = 00000000 Modules linked in: cx88_dvb(+) cx8802 cx88xx ir_common i2c_algo_bit tveeprom videobuf_dvb btcx_risc mga drm ipv6 fscpos eeprom nfsd exportfs stv0299 b2c2_flexcop_pci b2c2_flexcop cx24123 s5h1420 ves1x93 dvb_ttpci dvb_core saa7146_vv saa7146 videobuf_dma_sg videobuf_core videodev v4l1_compat ttpci_eeprom lirc_serial lirc_dev usbhid rtc uhci_hcd 8139too i2c_piix4 i2c_core usbcore evdev Pid: 4249, comm: modprobe Not tainted (2.6.27-gentoo #3) EIP: 0060:[<e084d4ef>] EFLAGS: 00010296 CPU: 0 EIP is at i2c_transfer+0x1f/0x80 [i2c_core] EAX: 00000000 EBX: ffffffa1 ECX: 00000002 EDX: d6c71e3c ESI: d80cd050 EDI: d8093c00 EBP: d6c71e20 ESP: d6c71e0c DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068 Signed-off-by:
-
Suresh Siddha authored
Impact: driver could possibly stomp on resources outside of its scope {mchehab@redhat.com: I got two versions of the same patch (identical, except for whitespacing). One authored by Andy Burns and another authored by Suresh Siddha. Due to that, I'm applying the one that has less CodingStyle errors. I'm also adding both comments and the SOB's for both patches, since they are both interesting} Suresh Siddha commented: Alexey Fisher reported: > resource map sanity check conflict: 0xcfeff800 0xcff007ff 0xcfe00000 > 0xcfefffff PCI Bus 0000:01 BAR base is located in the middle of the 4K page and the hardcoded size argument makes the request span two pages causing the conflict. Fix the hard coded size argument in ioremap(). Andy Burns commented: I have already sent this patch on the linux-dvb list, but it didn't get much attention, so re-sending direct, I hope you all don't mind. While attempting to run mythtv in a xen domU, I encountered problems loading the driver for my saa7134 card, with an error from ioremap(). This error was due to the driver allocating an incorrectly sized mmio area, which was trapped by xen's permission checks, but this would go un-noticed on a kernel without xen. My card has a 1K sized mmio area, I've had information that other cards have 2K areas, perhaps others have different sizes, yet the driver always attempts to map 4K. I realise that the granularity of mapping is the page size, which typically would be 4K, but unless the card's base address happens to fall on a 4K boundary (mine does not) then the base+4K will end up spanning two pages, and this is when the error occurs under xen. My patch uses the pci_resource_len macro to determine the size required for the user's particular card, instead of the hardcoded 4K value. I've tested with a couple of printk() inside ioremap() that the start address and size do get rounded to the closest page boundary. With this patch I am able to successfully load the saa7134 driver and run mythtv under xen with my card, subject to correct pollirq settings in case of shared IRQ, I am still seeing occasional DMA panics, which I think are related to swiotlb handling by dom0/domU, usually the panic occurs when changing mux, once tuned to a mux, 12 hour continuous recordings are possible without errors. Reported-by:Alexey Fisher <bug-track@fisher-privat.net> Tested-by:
Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by:
Andy Burns <andy@burns.net> Signed-off-by:
Ingo Molnar <mingo@elte.hu> Signed-off-by:
-
Jonathan Corbet authored
Remove lock_kernel() call from cafe_ccic.c Commit d56dc612 added lock_kernel() calls to cafe_ccic.c. But that driver was written with proper locking and does not need the BKL, so take it back out. Signed-off-by:
Jonathan Corbet <corbet@lwn.net> Signed-off-by:
-
Gregor Jasny authored
This patch adds the missing compat ioctls that are needed to operate Skype in combination with libv4l and a MJPEG only camera. If you think it's trivial enough please submit it to -stable, too. Signed-off-by:
Gregor Jasny <gjasny@web.de> Signed-off-by:
-
Mauro Carvalho Chehab authored
As reported by David Ellingsworth: > I'm not sure if it matters or not, but the ibmcam driver in the > Mauro's linux-2.6 git tree in the for_linus branch is currently > broken. uvd is equal to NULL during most of ibmcam_probe. Due to that, an OOPS is generated at dev_info. This patch replaces uvd->dev->dev to dev->dev inside this routine. Signed-off-by:
David Ellingsworth <david@identd.dyndns.org>
-
Alexey Klimov authored
This patch add support for new device named KWorld USB FM Radio SnapMusic Mobile 700 (FM700). And changes few lines in comments. Signed-off-by:
Alexey Klimov <klimov.linux@gmail.com> Acked-by:
-
Antoine Jacquet authored
Update Kconfig to add missing dependency on zl10353 for dtv5100 driver. Signed-off-by:
Antoine Jacquet <royale@zerezo.com> Signed-off-by:
-
Manu Abraham authored
rather than implementing different ways leading to confusion. This allows multiple gate_enable/disable's in the tuner_read/write functions, thereby lesser number of I/O operations throughout, eventually leading to better results. As a side effect demods that detect the STOP bit for auto closing of the gate can be avoided, thereby a very minimal gain in disabling the auto detect feature as well. Improves readability on the device control. Signed-off-by:
Manu Abraham <manu@linuxtv.org> Signed-off-by:
-
Jean Delvare authored
The tuner-3036 and dpc7146 drivers have been deleted now so we can remove the corresponding entries from feature-removal-schedule.txt. (Thanks for doing this, BTW.) Signed-off-by:
-
Alexey Klimov authored
This device is already handled by radio-si470x driver, and we therefore want usbhid to ignore it. Signed-off-by:
-
- 10 Nov, 2008 8 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: ALSA: hda - Make the HP EliteBook 8530p use AD1884A model laptop ALSA: gusextreme: Fix build errors ALSA: hdsp: check for iobox and upload firmware during ioctl ALSA: HDSP: check for io box before uploading firmware ALSA: hda - Add another HP model (6730s) for AD1884A alsa: fix snd_BUG_on() and friends ALSA: hda - Add a quirk for MEDION MD96630 ALSA: hda - Limit the number of GPIOs show in proc
-
Takashi Iwai authored
-
Travis Place authored
Added a QUIRK to patch_analog.c for the HP Elitebook 8530p (IDs 0x103c:0x30e7) to use AD1884A model 'laptop' by default. Playback and Capture confirmed working. Signed-off-by:
Travis Place <wishie@wishie.net> Signed-off-by:
Takashi Iwai <tiwai@suse.de>
-
Tejun Heo authored
This patch reverts the following three commits which convert libata to use block layer tagging. 43a49cbd e013e13b 2fca5ccf Although using block layer tagging is the right direction, due to the tight coupling among tag number, data structure allocation and hardware command slot allocation, libata doesn't work correctly with the current conversion. The biggest problem is guaranteeing that tag 0 is always used for non-NCQ commands. Due to the way blk-tag is implemented and how SCSI starts and finishes requests, such guarantee can't be made. I'm not sure whether this would actually break any low level driver but it doesn't look like a good idea to break such assumption given the frailty of ATA controllers. So, for the time being, keep using the old dumb in-libata qc allocation. Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Jens Axobe <jens.axboe@oracle.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Ville Syrjala authored
gusextreme depends on opl3 support. Add the approriate select to Kconfig. Also remove the unnecessary hwdep select. Relevant build errors: ERROR: "snd_opl3_hwdep_new" [sound/isa/gus/snd-gusextreme.ko] undefined! ERROR: "snd_opl3_create" [sound/isa/gus/snd-gusextreme.ko] undefined! Signed-off-by:
Ville Syrjala <syrjala@sci.fi> Signed-off-by:
-
Linus Torvalds authored
-
Arjan van de Ven authored
It's showing up as regressions; disabling it very likely just papers over an underlying issue, but time is running out for 2.6.28, lets get back to this for 2.6.29 Fixes: #11826 and #11893 Signed-off-by:
Arjan van de Ven <arjan@linux.intel.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixesLinus Torvalds authored
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes: kbuild: Fixup deb-pkg target to generate separate firmware deb
-
- 09 Nov, 2008 10 commits
-
-
Jonathan McDowell authored
The below is a simplistic fix for "make deb-pkg"; it splits the firmware out to a linux-firmware-image package and adds an (unversioned) Suggests to the linux package for this firmware. Signed-Off-By:
Jonathan McDowell <noodles@earth.li> Acked-by:
Frans Pop <elendil@planet.nl> Signed-off-by:
Sam Ravnborg <sam@ravnborg.org>
-
Linus Torvalds authored
The "Exclude staging drivers" question is there so that we don't build staging drivers for allyesconfig or allnoconfig settings, but it's very irritating when you've already said "no" to staging drivers earlier. There is absolutely no point in declining twice - once you've declined the staging drivers, you're done. So make the second question depend on the first question having been answered in the affirmative. Signed-off-by: -
git://linux-nfs.org/~bfields/linuxLinus Torvalds authored
* 'for-2.6.28' of git://linux-nfs.org/~bfields/linux: Fix nfsd truncation of readdir results
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tipLinus Torvalds authored
* 'cpus4096' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: cpumask: introduce new API, without changing anything, v3 cpumask: new API, v2 cpumask: introduce new API, without changing anything
-
Doug Nazar authored
Commit 8d7c4203 "nfsd: fix failure to set eof in readdir in some situations" introduced a bug: on a directory in an exported ext3 filesystem with dir_index unset, a READDIR will only return about 250 entries, even if the directory was larger. Bisected it back to this commit; reverting it fixes the problem. It turns out that in this case ext3 reads a block at a time, then returns from readdir, which means we can end up with buf.full==0 but with more entries in the directory still to be read. Before 8d7c4203 (but after c002a6c7 "Optimise NFS readdir hack slightly"), this would cause us to return the READDIR result immediately, but with the eof bit unset. That could cause a performance regression (because the client would need more roundtrips to the server to read the whole directory), but no loss in correctness, since the cleared eof bit caused the client to send another readdir. After 8d7c4203, the setting of the eof bit made this a correctness problem. So, move nfserr_eof into the loop and remove the buf.full check so that we loop until buf.used==0. The following seems to do the right thing and reduces the network traffic since we don't return a READDIR result until the buffer is full. Tested on an empty directory & large directory; eof is properly sent and there are no more short buffers. Signed-off-by:
Doug Nazar <nazard@dragoninc.ca> Cc: David Woodhouse <David.Woodhouse@intel.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
J. Bruce Fields <bfields@citi.umich.edu>
-
Rusty Russell authored
Impact: cleanup Clean up based on feedback from Andrew Morton and others: - change to inline functions instead of macros - add __init to bootmem method - add a missing debug check Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
-
Miklos Szeredi authored
Previously I assumed that the receive queues of candidates don't change during the GC. This is only half true, nothing can be received from the queues (see comment in unix_gc()), but buffers could be added through the other half of the socket pair, which may still have file descriptors referring to it. This can result in inc_inflight_move_tail() erronously increasing the "inflight" counter for a unix socket for which dec_inflight() wasn't previously called. This in turn can trigger the "BUG_ON(total_refs < inflight_refs)" in a later garbage collection run. Fix this by only manipulating the "inflight" counter for sockets which are candidates themselves. Duplicating the file references in unix_attach_fds() is also needed to prevent a socket becoming a candidate for GC while the skb that contains it is not yet queued. Reported-by:
Andrea Bittau <a.bittau@cs.ucl.ac.uk> Signed-off-by:
Miklos Szeredi <mszeredi@suse.cz> CC: stable@kernel.org Signed-off-by:
-
Nicolas Pitre authored
Currently, all existing users of cnt32_to_63() are fine since the CPU architectures where it is used don't do read access reordering, and user mode preemption is disabled already. It is nevertheless a good idea to better elaborate usage requirements wrt preemption, and use an explicit memory barrier on SMP to avoid different CPUs accessing the counter value in the wrong order. On UP a simple compiler barrier is sufficient. Signed-off-by:
Nicolas Pitre <nico@marvell.com> Acked-by:
Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmcLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: mmc: struct device - replace bus_id with dev_name(), dev_set_name() mmc: increase SD write timeout for crappy cards
-
Takashi Iwai authored
Use menuconfig instead of flat configs so that you can disable/enable regulator items with one selection. Also, use depends instead of reverse selections to make life easier, too. Signed-off-by:
Liam Girdwood <lrg@slimlogic.co.uk>
-
