- 12 Jul, 2006 40 commits
-
-
David Brownell authored
Recent section changes broke gadget builds on some platforms. This patch is the best fix that's available until better section markings exist: - There's a lot of cleanup code that gets used in both init and exit paths; stop marking it as "__exit". (Best fix for this would be an "__init_or_exit" section marking, putting the cleanup in __init when __exit sections get discarded else in __exit.) - Stop marking the use-once probe routines as "__init" since references to those routines are not allowed from driver structures. They're now marked "__devinit", which in practice is a net lose. (Best fix for this is likely to separate such use-once probe routines from the driver structure ... but in general, all busses that aren't hotpluggable will be forced to waste memory for all probe-only code.) In general these broken section rules waste an average of two to four kBytes per driver of code bloat ... because none of the relevant code can ever be reused after module initialization. Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Phil Dibowitz authored
Please add the attached device to unusual_devs.h. Signed-off-by:
Phil Dibowitz <phil@ipom.com> Signed-off-by:
-
Colin Leroy authored
This patch adds the Testo USB interface to the list of devices recognized by the ftdi_sio module. This device is based on a FT232BL chip, and is used as an interface to get data from digital sensors (thermometer, etc). See http://www.testo.com/Signed-off-by:
Colin Leroy <colin@colino.net> Signed-off-by:
-
Lars Jacob authored
This patch (as749) extends the unusual_devs entry for the Sony DSC-T1 and T5 to cover the H5 as well. From: Lars Jacob <jacob.lars@googlemail.com> Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Alan Stern authored
This patch (as748) adds an unusual_devs entry for the Nokia E61 mobile phone. Signed-off-by:
-
Alan Stern authored
This patch (as745) adds an unusual_devs entry for the Nokia N91, just like the entry for the N80 added a couple of weeks ago. Apparently Nokia isn't using very good firmware these days... Signed-off-by:
-
Dan Streetman authored
I just got a "ZyXEL Prestige USB Adapter" that is actually RTL8150 adapter. Here is the relevant /proc/bus/usb/devices output (after adding the vendor/product IDs to the driver): T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#=119 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0586 ProdID=401a Rev= 1.00 S: Manufacturer=ZyXEL S: Product=Prestige USB Adapter S: SerialNumber=1027 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=120mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=rtl8150 E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=1ms This patch adds the ZyXEL vendor ID to the rtl8150.c driver. The device has absolutely no identifying marks on the outside for model type, just a serial number, and I can't find anything on ZyXEL's website, so I called the product ID PRODUCT_ID_PRESTIGE to match the product string. Signed-off-by:
Dan Streetman <ddstreet@ieee.org> Acked-by: <petkan@users.sourceforge.net> Signed-off-by:
-
Matthias Urlichs authored
Yet another "same name, somewhat different hardware" product. Signed-Off-By:
Matthias Urlichs <smurf@smurf.noris.de> Signed-off-by:
-
Navaho Gunleg authored
This patch is to get the WiseGroup.,Ltd SmartJoy Dual Plus PS2-to-USB Adapter [0x6677:0x8802] correctly detected. It sets the NOGET and MULTI_INPUT quirks to make 2 joystick nodes appear in stead of only one. (As of yet, only confirmed working by myself.) Signed-off-by:
Navaho Gunleg <navahogunleg@gmail.com> Signed-off-by:
-
Bart Oldeman authored
The below patch fixes the ipw module in kernel 2.6.17 for me; without this change it simply does not work at all (all but the first writes are refused because write_urb_busy is always 1). This problem was there in 2.6.15 as well, but at that point I used the (updated) ipw.c, version 0.4, from http://www.neology.co.za/products/opensource/ipwireless/ which no longer compiles with 2.6.17. It can be made to after a few changes but obviously it's easier if the built-in ipw driver works instead of having to download one from the neology site. From: Bart Oldeman <bartoldeman@users.sourceforge.net> Signed-off-by:
-
Michal Piotrowski authored
Devfs is gone. We can remove that information. Signed-off-by:
Michal Piotrowski <michal.k.k.piotrowski@gmail.com> Signed-off-by:
-
Christoph Lameter authored
Remove destructor and call kmem_cache_create with NULL for the destructor. Acked-by:
Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by:
Christoph Lameter <clameter@sgi.com> Signed-off-by:
Andrew Morton <akpm@osdl.org> Cc: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by:
-
Frank Gevaerts authored
Adds configurable waiting periods to the ipaq connection code. These are not needed when the pocketpc device is running normally when plugged in, but they need extra delays if they are physically connected while rebooting. There are two parameters : * initial_wait : this is the delay before the driver attemts to start the connection. This is needed because the pocktpc device takes much longer to boot if the driver starts sending control packets too soon. * connect_retries : this is the number of times the control urb is retried before finally giving up. The patch also adds a 1 second delay between retries. I'm not sure if the cases where this patch is useful are general enough to include this in the kernel. Signed-off-by:
Frank Gevaerts <frank.gevaerts@fks.be> Signed-off-by:
-
Frank Gevaerts authored
This patch fixes several problems in the ipaq.c driver with connecting and disconnecting pocketpc devices: * The read urb stayed active if the connect failed, causing nullpointer dereferences later on. * If a write failed, the driver continued as if nothing happened. Now it handles that case the same way as other usb serial devices (fix by Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>) Signed-off-by:
-
David Brownell authored
In a rare and all-but-unused path, the EHCI driver could reuse a variable in a way that'd make trouble. Specifically, if the first root hub port gets an overcurrent event (rare) during a remote wakeup scenario (all but unused in today's Linux, except for folk working with suspend-to-RAM and similar sleep states), that would look like a fatal error which would shut down the controller. Fix by not reusing that variable. Spotted by Per Hallsmark <saxofon@musiker.nu> Fixes http://bugzilla.kernel.org/show_bug.cgi?id=6661Signed-off-by:
-
Kevin Lloyd authored
This patch creates a new driver, sierra.c, that supports the new non-composite Sierra Wireless WWAN devices. The older Sierra Wireless and Airprime devices are supported in airprime.c. Signed-off-by:
Kevin Lloyd <linux@sierrawireless.com> Signed-off-by:
-
Eric Sesterhenn authored
coverity spotted (id #185) that we still use urb, if the allocation fails in the error path. This patch fixes this by returning directly. Signed-off-by:
Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by:
-
Kyle McMartin authored
Move variables only used on !__hppa__ into that #ifndef section. This cleans up a compiler warning on parisc. Problem pointed out by Joel Soete. Signed-off-by:
Kyle McMartin <kyle@parisc-linux.org> Signed-off-by:
-
Ian Abbott authored
This patch limits the amount of outstanding 'write' data that can be queued up for the ftdi_sio driver, to prevent userspace DoS attacks (or simple accidents) that use up all the system memory by writing lots of data to the serial port. The original patch was by Guillaume Autran, who in turn based it on the same mechanism implemented in the 'visor' driver. I (Ian Abbott) re-targeted the patch to the latest sources, fixed a couple of errors, renamed his new structure members, and updated the implementations of the 'write_room' and 'chars_in_buffer' methods to take account of the number of outstanding 'write' bytes. It seems to work fine, though at low baud rates it is still possible to queue up an amount of data that takes an age to shift (a job for another day!). Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Ian Abbott authored
The anti user-DoS mechanism in the USB serial 'visor' driver can fail in the following way: visor_open: priv->outstanding_urbs = 0 visor_write: ++priv->outstanding_urbs visor_close: visor_open: priv->outstanding_urbs = 0 visor_write_bulk_callback: --priv->outstanding_urbs So priv->outstanding_urbs ends up as (unsigned long)(-1). Not good! I haven't seen this happen with the visor driver as I don't have the hardware, but I have seen it while testing a patch to implement the same functionality in the ftdi_sio driver (patch not yet submitted). The fix is pretty simple: don't reinitialize outstanding_urbs in visor_open. (Again, I haven't tested the fix in visor, but I have tested it in ftdi_sio.) Signed-off-by:
-
Phil Dibowitz authored
This patch adds the kernel version to the usb-storage Protocol/SubClass unneeded message in order to help us troubleshoot such problems. Signed-off-by:
Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by:
-
Phil Dibowitz authored
This patch adds a US_FL_MAX_SECTORS_64 and removes the Genesys special-cases for this that were in scsiglue.c. It also adds the flag to other devices reported to need it. Signed-off-by:
-
Alan Stern authored
This patch (as731) makes a couple of small fixes to the hub_port_resume routine: Don't return status >= 0 when an error occurs; Clear the port-change-suspend status indicator after resuming a device. Signed-off-by:
-
Ernis authored
This patch (as730) contains an unusual_devs entry for a Samsung MP3 device. From: Ernis <ernisv@gmail.com> Signed-off-by:
-
Davide Perini authored
This patch (as725) adds an unusual_devs entry for the Motorola RAZR V3x. From: Davide Perini <perini.davide@dpsoftware.org> Signed-off-by:
-
Alan Stern authored
finish_device_resume() in the hub driver isn't careful always to return a negative code in all the error pathways. It also doesn't return 0 in all the success pathways. This patch (as724) fixes the behavior. Signed-off-by:
-
Alan Stern authored
My recent patch converting usb-storage to use usb_reset_composite_device() added a bug, a race between reset and disconnect. It was necessary to drop the private lock while executing a reset, and if a disconnect occurs at that time it will cause a crash. This patch (as722) fixes the problem by explicitly checking for an early termination after executing each command. Signed-off-by:
-
Oliver Neukum authored
this adds better debugging output & an update of the quirk list to the acm driver Signed-off-by:
Oliver Neukum <oliver@neukum.name> Signed-off-by:
-
Oliver Bock authored
This is a new driver for the Cypress CY7C63xxx mirco controller series. It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus GmbH. It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I ported to kernel 2.6 using sysfs. I intend to support more controllers of this family (and more features) as soon as I get hold of the required IDs etc. Please see the source code's header for more information. Signed-off-by:
Oliver Bock <o.bock@fh-wolfenbuettel.de> Signed-off-by:
-
Zoran Marceta authored
usbfs stores the wrong signal number in the siginfo structure used for notifying user programs about device disconnect. This patch (as726) fixes it. From: Zoran Marceta <Zoran.Marceta@micronasnit.com> Signed-off-by:
-
Matthew Meno authored
The Susteen Datapilot cable (http://www.susteen.com/productdetail/71/producthl/Notempty) has an internal pl2303 to communicate with a set of dummy connector-ends that connect to a variety of cell phones. I've found that it works right out of the box by simply adding the product/vendor id to the pl2303 driver. Signed-off-by:
Matt Meno <mmeno@idealcorp.com> Signed-off-by:
-
Inaky Perez-Gonzalez authored
This patch adds basic Wireless USB 1.0 definitions to usb_ch9.h that fit into the existing set of declarations. Boils down to two new recipients for requests (ports and remote pipes), rpipe reset and abort request codes and wire adapter and remote pipe descriptor types. Wire adapters are the USB <-> Wireless USB adaptors; remote pipes are used by those adapters to pipe the host <-> endpoint traffic. Signed-off-by:
Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Signed-off-by:
-
Pete Zaitcev authored
This patch fixes blatant leaks in visor driver and makes it report mode sensible things in ->write_room (this is only needed if your visor is a terminal though). It is made to fit into 80 columns with a temporary variable. Might even save a few instructions... Signed-off-by:
Pete Zaitcev <zaitcev@redhat.com> Signed-off-by:
-
Pete Zaitcev authored
This fix addresses two issues: - Unattached port structures were not freed - My initial fix for crash when eventd runs a work in a freed port did not go far enough Signed-off-by:
-
David Miller authored
I noticed this while debugging something unrelated on sparc64. Signed-off-by:
David S. Miller <davem@davemloft.net> Acked-by:
David Brownell <david-b@pacbell.net> Signed-off-by:
-
Christophe Mariac authored
Signed-off-by: -
D. Peter Siddons authored
Signed-off-by: -
Peter Moulder authored
Text from the back of the box, for your information/amusement: USB DATA CABLE FOR K700 Series The USB Cable is an ideal link between your mobile phone and PC. Employing the user-friendiy [sic] USB standard,its capacity for rapid data transfer enables functions such as synchronization of phone book and calendar,as well as Internet browsing via a modem-enabled phone.Autual [sic] connection speed is dependent on phone capacity. MADE IN CHINA From: Peter Moulder <Peter.Moulder@infotech.monash.edu.au> Signed-off-by: -
Randy Dunlap authored
Warning(/var/linsrc/linux-2617-g4//include/linux/usb.h:66): No description found for parameter 'ep_dev' Signed-off-by:
Randy Dunlap <rdunlap@xenotime.net> Signed-off-by:
-
Lennert Buytenhek authored
This patch adds OHCI glue bits for the USB host interface in the Cirrus ep93xx (arm920t) CPU. Signed-off-by:
Lennert Buytenhek <buytenh@wantstofly.org> Acked-by:
-
