- 25 Jan, 2016 40 commits
-
-
Nikesh Oswal authored
commit e73694d8 upstream. For a sample rate of 12kHz the bclk was taken from the 44.1kHz table as we test for a multiple of 8kHz. This patch fixes this issue by testing for multiples of 4kHz instead. Signed-off-by:
Nikesh Oswal <Nikesh.Oswal@cirrus.com> Signed-off-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Mark Brown <broonie@kernel.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Ashok Raj authored
commit d90167a9 upstream. Intel's MCA implementation broadcasts MCEs to all CPUs on the node. This poses a problem for offlined CPUs which cannot participate in the rendezvous process: Kernel panic - not syncing: Timeout: Not all CPUs entered broadcast exception handler Kernel Offset: disabled Rebooting in 100 seconds.. More specifically, Linux does a soft offline of a CPU when writing a 0 to /sys/devices/system/cpu/cpuX/online, which doesn't prevent the #MC exception from being broadcasted to that CPU. Ensure that offline CPUs don't participate in the MCE rendezvous and clear the RIP valid status bit so that a second MCE won't cause a shutdown. Without the patch, mce_start() will increment mce_callin and wait for all CPUs. Offlined CPUs should avoid participating in the rendezvous process altogether. Signed-off-by:
Ashok Raj <ashok.raj@intel.com> [ Massage commit message. ] Signed-off-by:
Borislav Petkov <bp@suse.de> Reviewed-by:
Tony Luck <tony.luck@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/1449742346-21470-2-git-send-email-bp@alien8.deSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Roman Volkov authored
commit 0f090bf1 upstream. Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver is already in the kernel, this node enables the controller support for WM8650 Signed-off-by:
Roman Volkov <rvolkov@v1ros.org> Reviewed-by:
Alexey Charkov <alchark@gmail.com> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Qiu Peiyang authored
commit f36d1be2 upstream. When we do cat /sys/kernel/debug/tracing/printk_formats, we hit kernel panic at t_show. general protection fault: 0000 [#1] PREEMPT SMP CPU: 0 PID: 2957 Comm: sh Tainted: G W O 3.14.55-x86_64-01062-gd4acdc7 #2 RIP: 0010:[<ffffffff811375b2>] [<ffffffff811375b2>] t_show+0x22/0xe0 RSP: 0000:ffff88002b4ebe80 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000004 RDX: 0000000000000004 RSI: ffffffff81fd26a6 RDI: ffff880032f9f7b1 RBP: ffff88002b4ebe98 R08: 0000000000001000 R09: 000000000000ffec R10: 0000000000000000 R11: 000000000000000f R12: ffff880004d9b6c0 R13: 7365725f6d706400 R14: ffff880004d9b6c0 R15: ffffffff82020570 FS: 0000000000000000(0000) GS:ffff88003aa00000(0063) knlGS:00000000f776bc40 CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033 CR2: 00000000f6c02ff0 CR3: 000000002c2b3000 CR4: 00000000001007f0 Call Trace: [<ffffffff811dc076>] seq_read+0x2f6/0x3e0 [<ffffffff811b749b>] vfs_read+0x9b/0x160 [<ffffffff811b7f69>] SyS_read+0x49/0xb0 [<ffffffff81a3a4b9>] ia32_do_call+0x13/0x13 ---[ end trace 5bd9eb630614861e ]--- Kernel panic - not syncing: Fatal exception When the first time find_next calls find_next_mod_format, it should iterate the trace_bprintk_fmt_list to find the first print format of the module. However in current code, start_index is smaller than *pos at first, and code will not iterate the list. Latter container_of will get the wrong address with former v, which will cause mod_fmt be a meaningless object and so is the returned mod_fmt->fmt. This patch will fix it by correcting the start_index. After fixed, when the first time calls find_next_mod_format, start_index will be equal to *pos, and code will iterate the trace_bprintk_fmt_list to get the right module printk format, so is the returned mod_fmt->fmt. Link: http://lkml.kernel.org/r/5684B900.9000309@intel.com Fixes: 102c9323 "tracing: Add __tracepoint_string() to export string pointers" Signed-off-by:
Qiu Peiyang <peiyangx.qiu@intel.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Colin Ian King authored
commit 713a3e4d upstream. Fix build warning: scripts/recordmcount.c:589:4: warning: format not a string literal and no format arguments [-Wformat-security] sprintf("%s: failed\n", file); Fixes: a50bd439 ("ftrace/scripts: Have recordmcount copy the object file") Link: http://lkml.kernel.org/r/1451516801-16951-1-git-send-email-colin.king@canonical.com Cc: Li Bin <huawei.libin@huawei.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Thomas Gleixner authored
commit abc7e40c upstream. If a interrupt chip utilizes chip->buslock then free_irq() can deadlock in the following way: CPU0 CPU1 interrupt(X) (Shared or spurious) free_irq(X) interrupt_thread(X) chip_bus_lock(X) irq_finalize_oneshot(X) chip_bus_lock(X) synchronize_irq(X) synchronize_irq() waits for the interrupt thread to complete, i.e. forever. Solution is simple: Drop chip_bus_lock() before calling synchronize_irq() as we do with the irq_desc lock. There is nothing to be protected after the point where irq_desc lock has been released. This adds chip_bus_lock/unlock() to the remove_irq() code path, but that's actually correct in the case where remove_irq() is called on such an interrupt. The current users of remove_irq() are not affected as none of those interrupts is on a chip which requires buslock. Reported-by:
Fredrik Markström <fredrik.markstrom@gmail.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Dan Carpenter authored
commit 3358a5c0 upstream. In the original code, if we succeeded on the last iteration through the loop then we still returned failure. Fixes: 389e4e04 ('qlcnic: fix a timeout loop') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Andrey Ryabinin authored
commit e459dfee upstream. ip6addrlbl_get() has never worked. If ip6addrlbl_hold() succeeded, ip6addrlbl_get() will exit with '-ESRCH'. If ip6addrlbl_hold() failed, ip6addrlbl_get() will use about to be free ip6addrlbl_entry pointer. Fix this by inverting ip6addrlbl_hold() check. Fixes: 2a8cc6c8 ("[IPV6] ADDRCONF: Support RFC3484 configurable address selection policy table.") Signed-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by:
Cong Wang <cwang@twopensource.com> Acked-by:
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Eugenia Emantayev authored
commit 90683061 upstream. mlx4_en_init_timestamp was called before creation of netdev and port init, thus used uninitialized values. Specifically - NIC frequency was incorrect causing wrong calculations and later wrong HW timestamps. Fixes: 1ec4864b ('net/mlx4_en: Fixed crash when port type is changed') Signed-off-by:
Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by:
Marina Varshaver <marinav@mellanox.com> Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Eugenia Emantayev authored
commit fc9f5ea9 upstream. Service task is responsible for other tasks in addition to timestamping overflow check. Launch it even if timestamping is not supported by device. Fixes: 07841f9d ('net/mlx4_en: Schedule napi when RX buffers allocation fails') Signed-off-by:
Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Andrew Banman authored
commit 5f0f2887 upstream. test_pages_in_a_zone() does not account for the possibility of missing sections in the given pfn range. pfn_valid_within always returns 1 when CONFIG_HOLES_IN_ZONE is not set, allowing invalid pfns from missing sections to pass the test, leading to a kernel oops. Wrap an additional pfn loop with PAGES_PER_SECTION granularity to check for missing sections before proceeding into the zone-check code. This also prevents a crash from offlining memory devices with missing sections. Despite this, it may be a good idea to keep the related patch '[PATCH 3/3] drivers: memory: prohibit offlining of memory blocks with missing sections' because missing sections in a memory block may lead to other problems not covered by the scope of this fix. Signed-off-by:
Andrew Banman <abanman@sgi.com> Acked-by:
Alex Thorlton <athorlton@sgi.com> Cc: Russ Anderson <rja@sgi.com> Cc: Alex Thorlton <athorlton@sgi.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Greg KH <greg@kroah.com> Cc: Seth Jennings <sjennings@variantweb.net> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Joseph Qi authored
commit 5c9ee4cb upstream. When resizing, it firstly extends the last gd. Once it should backup super in the gd, it calculates new backup super and update the corresponding value. But it currently doesn't consider the situation that the backup super is already done. And in this case, it still sets the bit in gd bitmap and then decrease from bg_free_bits_count, which leads to a corrupted gd and trigger the BUG in ocfs2_block_group_set_bits: BUG_ON(le16_to_cpu(bg->bg_free_bits_count) < num_bits); So check whether the backup super is done and then do the updates. Signed-off-by:
Joseph Qi <joseph.qi@huawei.com> Reviewed-by:
Jiufei Xue <xuejiufei@huawei.com> Reviewed-by:
Yiwen Jiang <jiangyiwen@huawei.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Al Viro authored
commit 76cc404b upstream. Reviewed-by:
Jeff Layton <jeff.layton@primarydata.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
James Hogan authored
commit 5dc62fdd upstream. The strlen_user() function calls __strlen_kernel_asm in both branches of the eva_kernel_access() conditional. For EVA it should be calling __strlen_user_eva for user accesses, otherwise it will load from the kernel address space instead of the user address space, and the access checking will likely be ineffective at preventing it due to EVA's overlapping user and kernel address spaces. This was found after extending the test_user_copy module to cover user string access functions, which gave the following error with EVA: test_user_copy: illegal strlen_user passed Fortunately the use of strlen_user() has been all but eradicated from the mainline kernel, so only out of tree modules could be affected. Fixes: e3a9b07a ("MIPS: asm: uaccess: Add EVA support for str*_user operations") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/10842/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Mario Kleiner authored
commit 9f660a1c upstream. Without this patch, internal speaker and line-out work, but front headphone output jack stays silent on the Mac Pro 4,1. This code path also gets executed on the MacPro 5,1 due to identical codec SSID, but i don't know if it has any positive or adverse effects there or not. (v2) Implement feedback from Takashi Iwai: Reuse alc889_fixup_mbp_vref and just add a new nid 0x19 for the MacPro 4,1. Signed-off-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Helge Deller authored
commit 71a71fb5 upstream. On parisc syscalls which are interrupted by signals sometimes failed to restart and instead returned -ENOSYS which in the worst case lead to userspace crashes. A similiar problem existed on MIPS and was fixed by commit e967ef02 ("MIPS: Fix restart of indirect syscalls"). On parisc the current syscall restart code assumes that all syscall callers load the syscall number in the delay slot of the ble instruction. That's how it is e.g. done in the unistd.h header file: ble 0x100(%sr2, %r0) ldi #syscall_nr, %r20 Because of that assumption the current code never restored %r20 before returning to userspace. This assumption is at least not true for code which uses the glibc syscall() function, which instead uses this syntax: ble 0x100(%sr2, %r0) copy regX, %r20 where regX depend on how the compiler optimizes the code and register usage. This patch fixes this problem by adding code to analyze how the syscall number is loaded in the delay branch and - if needed - copy the syscall number to regX prior returning to userspace for the syscall restart. Signed-off-by:
Helge Deller <deller@gmx.de> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Michael Holzheu authored
commit 272fa59c upstream. The print_insn() function returns strings like "lghi %r1,0". To escape the '%' character in sprintf() a second '%' is used. For example "lghi %%r1,0" is converted into "lghi %r1,0". After print_insn() the output string is passed to printk(). Because format specifiers like "%r" or "%f" are ignored by printk() this works by chance most of the time. But for instructions with control registers like "lctl %c6,%c6,780" this fails because printk() interprets "%c" as character format specifier. Fix this problem and escape the '%' characters twice. For example "lctl %%%%c6,%%%%c6,780" is then converted by sprintf() into "lctl %%c6,%%c6,780" and by printk() into "lctl %c6,%c6,780". Signed-off-by:
Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> [ luis: backported to 3.16: - drop condition with OPERAND_VR introduced only with commit 3585cb02 ("s390/disassembler: add vector instructions") ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Xiong Zhang authored
commit 3e6db33a upstream. It takes three minutes to enter into hibernation on some OEM SKL machines and we see many codec spurious response after thaw() opertion. This is because HDA is still in D0 state after freeze() call and pci_pm_freeze/pci_pm_freeze_noirq() don't set D3 hot in pci_bus driver. It seems bios still access HDA when system enter into freeze state, HDA will receive codec response interrupt immediately after thaw() call. Because of this unexpected interrupt, HDA enter into a abnormal state and slow down the system enter into hibernation. In this patch, we put HDA into D3 hot state in azx_freeze_noirq() and put HDA into D0 state in azx_thaw_noirq(). V2: Only apply this fix to SKL+ Fix compile error when CONFIG_PM_SLEEP isn't defined [Yet another fix for CONFIG_PM_SLEEP ifdef and the additional comment by tiwai] Signed-off-by:
Xiong Zhang <xiong.y.zhang@intel.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Steven Rostedt (Red Hat) authored
commit a50bd439 upstream. Russell King found that he had weird side effects when compiling the kernel with hard linked ccache. The reason was that recordmcount modified the kernel in place via mmap, and when a file gets modified twice by recordmcount, it will complain about it. To fix this issue, Russell wrote a patch that checked if the file was hard linked more than once and would unlink it if it was. Linus Torvalds was not happy with the fact that recordmcount does this in place modification. Instead of doing the unlink only if the file has two or more hard links, it does the unlink all the time. In otherwords, it always does a copy if it changed something. That is, it does the write out if a change was made. Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Russell King authored
commit dd39a265 upstream. recordmcount edits the file in-place, which can cause problems when using ccache in hardlink mode. Arrange for recordmcount to break a hardlinked object. Link: http://lkml.kernel.org/r/E1a7MVT-0000et-62@rmk-PC.arm.linux.org.ukSigned-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Krzysztof Hałasa authored
commit 3a35e470 upstream. Gateworks Ventana boards seem to need "RGMII-ID" (internal delay) PHY mode, instead of simple "RGMII", for their Marvell 88E1510 transceiver. Otherwise, the Ethernet MAC doesn't work with Marvell PHY driver (TX doesn't seem to work correctly). Tested on GW5400 rev. C. This bug affects ARM Fedora 23. Signed-off-by:
Krzysztof Hałasa <khalasa@piap.pl> Acked-by:
Tim Harvey <tharvey@gateworks.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Mans Rullgard authored
commit 1ea5998a upstream. Attempting to use this codec driver triggers a BUG() in regcache_sync() since no cache type is set. The register map of this device is fairly small and has few holes so a flat cache is suitable. Signed-off-by:
Mans Rullgard <mans@mansr.com> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Paul Mackerras authored
commit c20875a3 upstream. Currently it is possible for userspace (e.g. QEMU) to set a value for the MSR for a guest VCPU which has both of the TS bits set, which is an illegal combination. The result of this is that when we execute a hrfid (hypervisor return from interrupt doubleword) instruction to enter the guest, the CPU will take a TM Bad Thing type of program interrupt (vector 0x700). Now, if PR KVM is configured in the kernel along with HV KVM, we actually handle this without crashing the host or giving hypervisor privilege to the guest; instead what happens is that we deliver a program interrupt to the guest, with SRR0 reflecting the address of the hrfid instruction and SRR1 containing the MSR value at that point. If PR KVM is not configured in the kernel, then we try to run the host's program interrupt handler with the MMU set to the guest context, which almost certainly causes a host crash. This closes the hole by making kvmppc_set_msr_hv() check for the illegal combination and force the TS field to a safe value (00, meaning non-transactional). Signed-off-by:
Paul Mackerras <paulus@samba.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Michal Hocko authored
commit 751e5f5c upstream. kernel test robot has reported the following crash: BUG: unable to handle kernel NULL pointer dereference at 00000100 IP: [<c1074df6>] __queue_work+0x26/0x390 *pdpt = 0000000000000000 *pde = f000ff53f000ff53 *pde = f000ff53f000ff53 Oops: 0000 [#1] PREEMPT PREEMPT SMP SMP CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.4.0-rc4-00139-g373ccbe5 #1 Workqueue: events vmstat_shepherd task: cb684600 ti: cb7ba000 task.ti: cb7ba000 EIP: 0060:[<c1074df6>] EFLAGS: 00010046 CPU: 0 EIP is at __queue_work+0x26/0x390 EAX: 00000046 EBX: cbb37800 ECX: cbb37800 EDX: 00000000 ESI: 00000000 EDI: 00000000 EBP: cb7bbe68 ESP: cb7bbe38 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 CR0: 8005003b CR2: 00000100 CR3: 01fd5000 CR4: 000006b0 Stack: Call Trace: __queue_delayed_work+0xa1/0x160 queue_delayed_work_on+0x36/0x60 vmstat_shepherd+0xad/0xf0 process_one_work+0x1aa/0x4c0 worker_thread+0x41/0x440 kthread+0xb0/0xd0 ret_from_kernel_thread+0x21/0x40 The reason is that start_shepherd_timer schedules the shepherd work item which uses vmstat_wq (vmstat_shepherd) before setup_vmstat allocates that workqueue so if the further initialization takes more than HZ we might end up scheduling on a NULL vmstat_wq. This is really unlikely but not impossible. Fixes: 373ccbe5 ("mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress") Reported-by:
kernel test robot <ying.huang@linux.intel.com> Signed-off-by:
Michal Hocko <mhocko@suse.com> Tested-by:
Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Ben Hutchings <ben@decadent.org.uk> [ luis: backported to 3.16: based on Ben's backport to 3.2: - as with 3.2, there's a similar race but with the CPU hotplug code ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Chris Wilson authored
commit 611a7a4f upstream. One small change I forgot to make in commit c4d69da1 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Mon Sep 8 14:25:41 2014 +0100 drm/i915: Evict CS TLBs between batches was to update the copy width for the compact BLT copy instruction. Reported-by:
Thomas Richter <thor@math.tu-berlin.de> Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Thomas Richter <thor@math.tu-berlin.de> Cc: Jani Nikula <jani.nikula@intel.com> Tested-by:
Thomas Richter <thor@math.tu-berlin.de> Acked-by:
Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
James Morse authored
commit 1d5cda40 upstream. mmdebug.h uses BUILD_BUG_ON_INVALID(), assuming someone else included linux/bug.h. Include it ourselves. This saves build-failures such as: arch/arm64/include/asm/pgtable.h: In function 'set_pte_at': arch/arm64/include/asm/pgtable.h:281:3: error: implicit declaration of function 'BUILD_BUG_ON_INVALID' [-Werror=implicit-function-declaration] VM_WARN_ONCE(!pte_young(pte), Fixes: 02602a18 ("bug: completely remove code generated by disabled VM_BUG_ON()") Signed-off-by:
James Morse <james.morse@arm.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Hannes Frederic Sowa authored
commit 7bbadd2d upstream. Docbook does not like the definition of macros inside a field declaration and adds a warning. Move the definition out. Fixes: 79462ad0 ("net: add validation for the socket syscall protocol argument") Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Tilman Schmidt authored
commit 4c5e354a upstream. When shutting down the device, the struct ser_cardstate must not be kfree()d immediately after the call to platform_device_unregister() since the embedded struct platform_device is still in use. Move the kfree() call to the release method instead. Signed-off-by:
Tilman Schmidt <tilman@imap.cc> Fixes: 2869b23e ("drivers/isdn/gigaset: new M101 driver (v2)") Reported-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Dan Carpenter authored
commit 389e4e04 upstream. The problem here is that at the end of the loop we test for if idc->vnic_wait_limit is zero, but since idc->vnic_wait_limit-- is a post-op, it actually ends up set to (u8)-1. I have fixed this by moving the decrement inside the loop. Fixes: 486a5bc7 ('qlcnic: Add support for 83xx suspend and resume.') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Dan Carpenter authored
commit c7557e6a upstream. At the end of the loop we test "if (!count)" but because "count--" is a post-op then the loop will end with count set to -1. I have fixed this by changing it to --count. Fixes: c5aa9e3b ('amd-xgbe: Initial AMD 10GbE platform driver') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Dan Carpenter authored
commit 40d24c4d upstream. There are two issue here. 1) cnt starts as maxloop + 1 so all these loops iterate one more time than intended. 2) At the end of the loop we test for "if (maxloop && !cnt)" but for the first two loops, we end with cnt equal to -1. Changing this to a pre-op means we end with cnt set to 0. Fixes: cae86d4a ('mISDN: Add driver for Infineon ISDN chipset family') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Sergei Shtylyov authored
commit 3e230993 upstream. For the little-endian SH771x kernels the driver has to byte-swap the RX/TX buffers, however yet unset physcial address from the TX descriptor is used to call sh_eth_soft_swap(). Use 'skb->data' instead... Fixes: 31fcb99d ("net: sh_eth: remove __flush_purge_region") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Tobias Klauser authored
commit 20b08e1a upstream. mdiobus_alloc() might return NULL, but its return value is not checked in mdio_mux_init(). This could potentially lead to a NULL pointer dereference. Fix it by checking the return value Fixes: 0ca2997d ("netdev/of/phy: Add MDIO bus multiplexer support.") Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Stefan Wahren authored
commit 4c02cba1 upstream. Currently the provided initial value for bcm2835_gpio_direction_output has no effect. So fix this issue by changing the value before changing the GPIO direction. As a result we need to move the function below bcm2835_gpio_set. Suggested-by:
Martin Sperl <kernel@martin.sperl.org> Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Acked-by:
Eric Anholt <eric@anholt.net> Acked-by:
Stephen Warren <swarren@wwwdotorg.org> Fixes: e1b2dc70 ("pinctrl: add bcm2835 driver") Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> [ luis: backported to 3.16: - file rename: drivers/pinctrl/bcm/pinctrl-bcm2835.c -> drivers/pinctrl/pinctrl-bcm2835.c ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Alan Stern authored
commit e50293ef upstream. Commit 8520f380 ("USB: change hub initialization sleeps to delayed_work") changed the hub_activate() routine to make part of it run in a workqueue. However, the commit failed to take a reference to the usb_hub structure or to lock the hub interface while doing so. As a result, if a hub is plugged in and quickly unplugged before the work routine can run, the routine will try to access memory that has been deallocated. Or, if the hub is unplugged while the routine is running, the memory may be deallocated while it is in active use. This patch fixes the problem by taking a reference to the usb_hub at the start of hub_activate() and releasing it at the end (when the work is finished), and by locking the hub interface while the work routine is running. It also adds a check at the start of the routine to see if the hub has already been disconnected, in which nothing should be done. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Alexandru Cornea <alexandru.cornea@intel.com> Tested-by:
Alexandru Cornea <alexandru.cornea@intel.com> Fixes: 8520f380 ("USB: change hub initialization sleeps to delayed_work") Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ luis: backported to 3.16: - Added forward declaration of hub_release() which mainline had with commit 32a69589 ("usb: hub: convert khubd into workqueue") ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Dan Carpenter authored
commit abdc9a3b upstream. The code expects the loop to end with "retries" set to zero but, because it is a post-op, it will end set to -1. I have fixed this by moving the decrement inside the loop. Fixes: 014aa2a3 ('USB: ipaq: minor ipaq_open() cleanup.') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Konrad Rzeszutek Wilk authored
commit 408fb0e5 upstream. commit f598282f ("PCI: Fix the NIU MSI-X problem in a better way") teaches us that dealing with MSI-X can be troublesome. Further checks in the MSI-X architecture shows that if the PCI_COMMAND_MEMORY bit is turned of in the PCI_COMMAND we may not be able to access the BAR (since they are memory regions). Since the MSI-X tables are located in there.. that can lead to us causing PCIe errors. Inhibit us performing any operation on the MSI-X unless the MEMORY bit is set. Note that Xen hypervisor with: "x86/MSI-X: access MSI-X table only after having enabled MSI-X" will return: xen_pciback: 0000:0a:00.1: error -6 enabling MSI-X for guest 3! When the generic MSI code tries to setup the PIRQ without MEMORY bit set. Which means with later versions of Xen (4.6) this patch is not neccessary. This is part of XSA-157 Reviewed-by:
Jan Beulich <jbeulich@suse.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Konrad Rzeszutek Wilk authored
commit 7cfb905b upstream. Otherwise just continue on, returning the same values as previously (return of 0, and op->result has the PIRQ value). This does not change the behavior of XEN_PCI_OP_disable_msi[|x]. The pci_disable_msi or pci_disable_msix have the checks for msi_enabled or msix_enabled so they will error out immediately. However the guest can still call these operations and cause us to disable the 'ack_intr'. That means the backend IRQ handler for the legacy interrupt will not respond to interrupts anymore. This will lead to (if the device is causing an interrupt storm) for the Linux generic code to disable the interrupt line. Naturally this will only happen if the device in question is plugged in on the motherboard on shared level interrupt GSI. This is part of XSA-157 Reviewed-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Konrad Rzeszutek Wilk authored
commit a396f3a2 upstream. Otherwise an guest can subvert the generic MSI code to trigger an BUG_ON condition during MSI interrupt freeing: for (i = 0; i < entry->nvec_used; i++) BUG_ON(irq_has_action(entry->irq + i)); Xen PCI backed installs an IRQ handler (request_irq) for the dev->irq whenever the guest writes PCI_COMMAND_MEMORY (or PCI_COMMAND_IO) to the PCI_COMMAND register. This is done in case the device has legacy interrupts the GSI line is shared by the backend devices. To subvert the backend the guest needs to make the backend to change the dev->irq from the GSI to the MSI interrupt line, make the backend allocate an interrupt handler, and then command the backend to free the MSI interrupt and hit the BUG_ON. Since the backend only calls 'request_irq' when the guest writes to the PCI_COMMAND register the guest needs to call XEN_PCI_OP_enable_msi before any other operation. This will cause the generic MSI code to setup an MSI entry and populate dev->irq with the new PIRQ value. Then the guest can write to PCI_COMMAND PCI_COMMAND_MEMORY and cause the backend to setup an IRQ handler for dev->irq (which instead of the GSI value has the MSI pirq). See 'xen_pcibk_control_isr'. Then the guest disables the MSI: XEN_PCI_OP_disable_msi which ends up triggering the BUG_ON condition in 'free_msi_irqs' as there is an IRQ handler for the entry->irq (dev->irq). Note that this cannot be done using MSI-X as the generic code does not over-write dev->irq with the MSI-X PIRQ values. The patch inhibits setting up the IRQ handler if MSI or MSI-X (for symmetry reasons) code had been called successfully. P.S. Xen PCIBack when it sets up the device for the guest consumption ends up writting 0 to the PCI_COMMAND (see xen_pcibk_reset_device). XSA-120 addendum patch removed that - however when upstreaming said addendum we found that it caused issues with qemu upstream. That has now been fixed in qemu upstream. This is part of XSA-157 Reviewed-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Konrad Rzeszutek Wilk authored
commit 5e0ce145 upstream. The guest sequence of: a) XEN_PCI_OP_enable_msix b) XEN_PCI_OP_enable_msix results in hitting an NULL pointer due to using freed pointers. The device passed in the guest MUST have MSI-X capability. The a) constructs and SysFS representation of MSI and MSI groups. The b) adds a second set of them but adding in to SysFS fails (duplicate entry). 'populate_msi_sysfs' frees the newly allocated msi_irq_groups (note that in a) pdev->msi_irq_groups is still set) and also free's ALL of the MSI-X entries of the device (the ones allocated in step a) and b)). The unwind code: 'free_msi_irqs' deletes all the entries and tries to delete the pdev->msi_irq_groups (which hasn't been set to NULL). However the pointers in the SysFS are already freed and we hit an NULL pointer further on when 'strlen' is attempted on a freed pointer. The patch adds a simple check in the XEN_PCI_OP_enable_msix to guard against that. The check for msi_enabled is not stricly neccessary. This is part of XSA-157 Reviewed-by:
David Vrabel <david.vrabel@citrix.com> Reviewed-by:
Jan Beulich <jbeulich@suse.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-