g++ reports

	drivers/input/serio/i8042-x86ia64io.h:225:3: error: ‘.matches’ designator used multiple times in the same initializer list

C99 semantics is that last duplicated initialiser wins,
so DMI entry gets overwritten.

Fixes: a48491c6 ("Input: i8042 - add ByteSpeed touchpad to noloop table")
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Link: https://lore.kernel.org/r/20201228072335.GA27766@localhost.localdomainSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to the st1232 datasheet, the host has to wait for the device
to change into Normal state before accessing registers other than the
Status Register.

If the reset GPIO is wired, the device is powered on during driver
probe, just before reading the resolution.  However, the latter may
happen before the device is ready, leading to a probe failure:

    st1232-ts 1-0055: Failed to read resolution: -6

Fix this by waiting until the device is ready, by trying to read the
Status Register until it indicates so, or until timeout.

On Armadillo 800 EVA, typically the first read fails with an I2C
transfer error, while the second read indicates the device is ready.

Fixes: 3a54a215 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-4-geert+renesas@glider.beSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

st1232_ts_read_data() already reads ts->read_buf_len bytes (8 or 20
bytes) from the touchscreen controller.  This was fine when it was used
to read touch point coordinates only, but is overkill for reading the
touchscreen resolution, which just needs 3 bytes.

Optimize transfers by passing the wanted number of bytes.

Fixes: 3a54a215 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-3-geert+renesas@glider.beSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Before, the maximum coordinates were fixed to (799, 479) or (319, 479),
depending on touchscreen controller type.  The driver was changed to
read the actual values from the touchscreen controller, but did not take
into account the returned values are not the maximum coordinates, but
the touchscreen resolution (e.g. 800 and 480).

Fix this by subtracting 1.

Fixes: 3a54a215 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-2-geert+renesas@glider.beSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare input updates for 5.11 merge window.

There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201214223109.82924-1-colin.king@canonical.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

gcc -Warray-bounds warns about a serious bug in
cyapa_pip_retrieve_data_structure:

drivers/input/mouse/cyapa_gen6.c: In function 'cyapa_pip_retrieve_data_structure.constprop':
include/linux/unaligned/access_ok.h:40:17: warning: array subscript -1 is outside array bounds of 'struct retrieve_data_struct_cmd[1]' [-Warray-bounds]
   40 |  *((__le16 *)p) = cpu_to_le16(val);
drivers/input/mouse/cyapa_gen6.c:569:13: note: while referencing 'cmd'
  569 |  } __packed cmd;
      |             ^~~

Apparently the '-2' was added to the pointer instead of the value,
writing garbage into the stack next to this variable.

Fixes: c2c06c41 ("Input: cyapa - add gen6 device module support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026161332.3708389-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add new compatible strings and match data to support sc2730 and sc2721
which are two varieties of SC27XX family.
Signed-off-by: Nemo Han <nemo.han@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20201117034949.47877-2-zhang.lyra@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add new compatible strings to support sc2730 and sc2721 which are
two varieties of SC27XX family.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201117034949.47877-4-zhang.lyra@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert the sprd sc27xx vibrator binding to DT schema using json-schema.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201117034949.47877-3-zhang.lyra@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Make use of generic touchscreen_properties structure to add axis
inversion and swapping capabilities. It's configurable via devicetree
properties:
  touchscreen-inverted-x
  touchscreen-inverted-y
  touchscreen-swapped-x-y
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Link: https://lore.kernel.org/r/20200922093903.157232-1-s.riedmueller@phytec.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The touchscreen on the Teclast x98 Pro is also mounted upside-down in
relation to the display orientation.
Signed-off-by: Simon Beginn <linux@simonmicro.de>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20201117004253.27A5A27EFD@localhostSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We need to make sure we are not stomping on the control URB that was
issued when opening the device when attempting to toggle buzzer.
To do that we need to mark it as pending in cm109_open().

Reported-and-tested-by: syzbot+150f793ac5bc18eee150@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If device is set up as a wakeup source, I2C core configures the interrupt
line as wake IRQ and PM core automatically configures it for waking up the
system on system suspend transition, so we do not have to explicitly call
enable_irq_wake() and disable_irq_wake() in suspend/resume.

Link: https://lore.kernel.org/r/20201120073920.3214492-2-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We should not be configuring the controller as a wakeup source in the
driver, but rather rely on I2C core to mark it as such by either
instantiating as I2C_CLIENT_WAKEUP or specifying "wakeup-source" device
property.

Link: https://lore.kernel.org/r/20201120073920.3214492-1-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211085032.2598-1-zhengyongjun3@huawei.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211084957.2540-1-zhengyongjun3@huawei.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Adds support for the Dialog DA7280 LRA/ERM Haptic Driver with
multiple mode and integrated waveform memory and wideband support.
It communicates via an I2C bus to the device.
Signed-off-by: Roy Im <roy.im.opensource@diasemi.com>
Reviewed-by: Jes Sorensen <Jes.Sorensen@gmail.com>.
Link: https://lore.kernel.org/r/1e293e8c4830b09255af3b7e1721b73afaefdfa3.1606320459.git.Roy.Im@diasemi.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add device tree binding information for DA7280 haptic driver.
Example bindings for DA7280 are added.
Signed-off-by: Roy Im <roy.im.opensource@diasemi.com>
Reviewed-by: Rob Herring <robh@kernel.org>.
Link: https://lore.kernel.org/r/2bc9a4a9d083ea8f360ec75f6281b6de6c4ef284.1606320459.git.Roy.Im@diasemi.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds the da7280 bindings doc and driver to the Dialog
Semiconductor support list.
Signed-off-by: Roy Im <roy.im.opensource@diasemi.com>
Link: https://lore.kernel.org/r/e2a01173699486519f8da85b9283c6af8481fbdb.1606320459.git.Roy.Im@diasemi.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There are some version of Elan trackpads that send incorrect data when
in SMbus mode, unless they are switched to use 0x5f reports instead of
standard 0x5e. This patch implements querying device to retrieve chips
identifying data, and switching it, when needed to the alternative
report.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20201211071531.32413-1-jingle.wu@emc.com.twSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The 0x5F is a new trackpoint report type used by some modules.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20201211071511.32349-1-jingle.wu@emc.com.twSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add information found in downstream kernels, to make the code less
magic.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/728fff020bc92be10d84cc2a7ea8af6fd99af96c.1607669375.git.mirq-linux@rere.qmqm.plSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201210135943.1612-1-zhengyongjun3@huawei.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add COMPILE_TEST support to imx_keypad driver for better compile
testing coverage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1583137573-16628-1-git-send-email-Anson.Huang@nxp.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.

The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).

[1] commit bebcfd27 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Tested-by: Ronald Tschalär <ronald@innovation.ch>
Reviewed-by: Ronald Tschalär <ronald@innovation.ch>
Link: https://lore.kernel.org/r/20200227124534.23399-1-sergiu.cuciurean@analog.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.

The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).

[1] commit bebcfd27 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200227130336.27042-1-sergiu.cuciurean@analog.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.

The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).

[1] commit bebcfd27 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200228104508.15564-1-sergiu.cuciurean@analog.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of special-casing retrieval of number of X/Y electrodes based on
the firmware, let's select default values and mark registers as
non-existent on firmwares that do not support this operation.

Also mark "report rate" register as non-existent for generic firmwares
as having it set to 0 does not make sense.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Simon Budig <simon.budig@kernelconcepts.de>
Link: https://lore.kernel.org/r/X9FZFs3NZADoIhhH@google.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The touchpad operates in Basic Mode by default in the Acer BIOS
setup, but some Aspire/TravelMate models require the i8042 to be
reset in order to be correctly detected.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Link: https://lore.kernel.org/r/20201207071250.15021-1-chiu@endlessos.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Samsung touchkey controllers are often used with external pull-up
for the interrupt line and the I2C lines, so we might need to enable
a regulator to bring the lines into usable state. Otherwise, this might
cause spurious interrupts and reading from I2C will fail.

Implement support for a "vddio-supply" that is enabled by the
tm2-touchkey driver so that the regulator gets enabled when needed.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201203131242.44397-3-stephan@gerhold.netSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Samsung touchkey controllers are often used with external pull-up
for the interrupt line and the I2C lines, so we might need to enable
a regulator to bring the lines into usable state. Otherwise, this might
cause spurious interrupts and reading from I2C will fail.

Document support for a "vddio-supply" that is enabled by the tm2-touchkey
driver so that the regulator gets enabled when needed.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201203131242.44397-2-stephan@gerhold.netSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert the device tree bindings for tm2-touchkey to the YAML format.

While we're at it, clarify the descriptions a bit to make it clear that
this driver can be used for many different MCUs that all implement
a similar I2C protocol. Depending on the MCU the voltage requirements
may be different, on some devices the controller uses 2.2V, 2.8V or
even 3.3V for vcc-supply instead of 1.8V.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201203131242.44397-1-stephan@gerhold.netSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/linux-input/20190708123323.11943-1-huangfq.daxian@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

To let userspace know what 'scancodes' should be used in EVIOCGKEYCODE
and EVIOCSKEYCODE ioctls, we should send EV_MSC/MSC_SCAN events in
addition to EV_KEY/KEY_* events. The driver already declared MSC_SCAN
capability, so it is only matter of actually sending the events.

Link: https://lore.kernel.org/r/X87aOaSptPTvZ3nZ@google.comAcked-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This adds support for the power button attached to the Embedded Controller
on a Dell Wyse 3020 "Ariel" board.

The Embedded Controller's SPI interface is actually capable sending and
receiving the PS/2 keyboard and mouse protocol data, which looks like
a good fit for a serio driver. Howerver, I don't know of any machines where
this is actually used.

My board only has a single power button and no way to connect an actual
keyboard or a mouse. Using the atkbd driver with serio would be an overkill
and would be inconvenient for the userspace. Therefore this driver
registers an input device that is only capable of reporting the power
button presses and releases.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20201201083533.1724287-3-lkundrak@v3.skSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add binding document for the Dell Wyse 3020 a.k.a. "Ariel" Power Button.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201201083533.1724287-2-lkundrak@v3.skSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver has its own HID descriptor parsing code, that had and still
has several issues discovered by syzbot and other tools. Ideally we
should move the driver over to the HID subsystem, so that it uses proven
parsing code.  However the devices in question are EOL, and GTCO is not
willing to extend resources for that, so let's simply remove the driver.

Note that our HID support has greatly improved over the last 10 years,
we may also consider reverting 6f8d9e26 ("hid-core.c: Adds all GTCO
CalComp Digitizers and InterWrite School Products to blacklist") and see
if GTCO devices actually work with normal HID drivers.

Link: https://lore.kernel.org/r/X8wbBtO5KidME17K@google.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add the Lenovo Yoga Tablet2 1051L to the list of devices where the
ACPI AML code is poking the GPIO config register directly changing
the IRQ type to a low_level_irq, which we need to work around.

This fixes the home button on the Lenovo Yoga Tablet2 1051L not
working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201206161245.24798-1-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Raydium device does not like splitting of tx transactions into multiple
messages - one for the register address and one for the actual data. This
results in incorrect behavior on the device side.

This change updates raydium_i2c_read and raydium_i2c_write to create
i2c_msg arrays separately and passes those arrays into raydium_i2c_xfer
which decides based on the address whether the bank switch command should
be sent. The bank switch header is still added by raydium_i2c_read and
raydium_i2c_write to ensure that all these operations are performed as part
of a single I2C transfer. It guarantees that no other transactions are
initiated to any other device on the same bus after the bank switch command
is sent.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Link: https://lore.kernel.org/r/20201205005941.1427643-1-furquan@google.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>