Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains the first batch of Netfilter fixes for
your net tree:

1) Fix splat with IPv6 defragmenting locally generated fragments,
   from Florian Westphal.

2) Fix Incorrect check for missing attribute in nft_osf.

3) Missing INT_MIN & INT_MAX definition for netfilter bridge uapi
   header, from Jiri Slaby.

4) Revert map lookup in nft_numgen, this is already possible with
   the existing infrastructure without this extension.

5) Fix wrong listing of set reference counter, make counter
   synchronous again, from Stefano Brivio.

6) Fix CIDR 0 in hash:net,port,net, from Eric Westbrook.

7) Fix allocation failure with large set, use kvcalloc().
   From Andrey Ryabinin.

8) No need to disable BH when fetch ip set comment, patch from
   Jozsef Kadlecsik.

9) Sanity check for valid sysfs entry in xt_IDLETIMER, from
   Taehee Yoo.

10) Fix suspicious rcu usage via ip_set() macro at netlink dump,
    from Jozsef Kadlecsik.

11) Fix setting default timeout via nfnetlink_cttimeout, this
    comes with preparation patch to add nf_{tcp,udp,...}_pernet()
    helper.

12) Allow ebtables table nat to be of filter type via nft_compat.
    From Florian Westphal.

13) Incorrect calculation of next bucket in early_drop, do no bump
    hash value, update bucket counter instead. From Vasily Khoruzhick.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

alx_drv_name is not used outside main.c, so there's no reason for it to
have external linkage.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

When iptables command is executed, ip_{set/get}sockopt() try to upload
bpfilter.ko if bpfilter is enabled. if it couldn't find bpfilter.ko,
command is failed.
bpfilter.ko is generated if CONFIG_BPFILTER_UMH is enabled.
ip_{set/get}sockopt() only checks CONFIG_BPFILTER.
So that if CONFIG_BPFILTER is enabled and CONFIG_BPFILTER_UMH is disabled,
iptables command is always failed.

test config:
   CONFIG_BPFILTER=y
   # CONFIG_BPFILTER_UMH is not set

test command:
   %iptables -L
   iptables: No chain/target/match by that name.

Fixes: d2ba09c1 ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPPROTO_RAW isn't registred as an inet protocol, so
inet_protos[protocol] is always NULL for it.

Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Fixes: bf2ae2e4 ("sock_diag: request _diag module only when the family or proto has been registered")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no reason to discard using source link local address when
remote netconsole IPv6 address is set to be link local one.

The patch allows administrators to use IPv6 netconsole without
explicitly configuring source address:

    netconsole=@/,@fe80::5054:ff:fe2f:6012/
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure we call fib6_dump_end() if it happens that skb->len
is zero. rtnl_dump_all() can reset cb->args on the next loop
iteration there.

Fixes: 08e814c9 ("net/ipv6: Bail early if user only wants cloned entries")
Fixes: ae677bbb ("net: Don't return invalid table id error when dumping all families")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For non-zero return from dumpit() we should break the loop
in rtnl_dump_all() and return the result. Otherwise, e.g.,
we could get the memory leak in inet6_dump_fib() [1]. The
pointer to the allocated struct fib6_walker there (saved
in cb->args) can be lost, reset on the next iteration.

Fix it by partially restoring the previous behavior before
commit c63586dc ("net: rtnl_dump_all needs to propagate
error from dumpit function"). The returned error from
dumpit() is still passed further.

[1]:
unreferenced object 0xffff88001322a200 (size 96):
  comm "sshd", pid 1484, jiffies 4296032768 (age 1432.542s)
  hex dump (first 32 bytes):
    00 01 00 00 00 00 ad de 00 02 00 00 00 00 ad de  ................
    18 09 41 36 00 88 ff ff 18 09 41 36 00 88 ff ff  ..A6......A6....
  backtrace:
    [<0000000095846b39>] kmem_cache_alloc_trace+0x151/0x220
    [<000000007d12709f>] inet6_dump_fib+0x68d/0x940
    [<000000002775a316>] rtnl_dump_all+0x1d9/0x2d0
    [<00000000d7cd302b>] netlink_dump+0x945/0x11a0
    [<000000002f43485f>] __netlink_dump_start+0x55d/0x800
    [<00000000f76bbeec>] rtnetlink_rcv_msg+0x4fa/0xa00
    [<000000009b5761f3>] netlink_rcv_skb+0x29c/0x420
    [<0000000087a1dae1>] rtnetlink_rcv+0x15/0x20
    [<00000000691b703b>] netlink_unicast+0x4e3/0x6c0
    [<00000000b5be0204>] netlink_sendmsg+0x7f2/0xba0
    [<0000000096d2aa60>] sock_sendmsg+0xba/0xf0
    [<000000008c1b786f>] __sys_sendto+0x1e4/0x330
    [<0000000019587b3f>] __x64_sys_sendto+0xe1/0x1a0
    [<00000000071f4d56>] do_syscall_64+0x9f/0x300
    [<000000002737577f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
    [<0000000057587684>] 0xffffffffffffffff

Fixes: c63586dc ("net: rtnl_dump_all needs to propagate error from dumpit function")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the anycast.c init and cleanup functions which were inadvertently
added inside the CONFIG_PROC_FS definition.

Fixes: 2384d025 ("net/ipv6: Add anycast addresses to a global hashtable")
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 4d2c0cda set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.

Fixes: 4d2c0cda ("bonding: speed/duplex update at NETDEV_UP event")
CC: Mahesh Bandewar <maheshb@google.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:

$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]

Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd ("net: phy: realtek: add RTL8201F phy-id and functions").

Fix this by removing the offending slash in the driver name.

Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.

Fixes: 513588dd ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to rfc8260#section-4.3.2, SCTP_SS_DEFAULT is required to
defined as SCTP_SS_FCFS or SCTP_SS_RR.

SCTP_SS_FCFS is used for SCTP_SS_DEFAULT's value in this patch.

Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As defined in rfc6525#section-6.1.3, SCTP_STREAM_CHANGE_DENIED
and SCTP_STREAM_CHANGE_FAILED should be used instead of
SCTP_ASSOC_CHANGE_DENIED and SCTP_ASSOC_CHANGE_FAILED.

To keep the compatibility, fix it by adding two macros.

Fixes: b444153f ("sctp: add support for generating add stream change event notification")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-11-03

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix BPF prog kallsyms and bpf_prog_get_info_by_fd() jited address export
   to not use page start but actual start instead to work correctly with
   profiling e.g. finding hot instructions from stack traces. Also fix latter
   with regards to dumping address and jited len for !multi prog, from Song.

2) Fix bpf_prog_get_info_by_fd() for !root to zero info.nr_jited_func_lens
   instead of leaving the user provided length, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.

Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.

Fixes: 9148e7cf ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_CC_OPTIMIZE_FOR_DEBUGGING is enabled, the compiler
fails to optimize out a dead code path, which leads to a link failure:

net/openvswitch/conntrack.o: In function `ovs_ct_set_labels':
conntrack.c:(.text+0x2e60): undefined reference to `nf_connlabels_replace'

In this configuration, we can take a shortcut, and completely
remove the contrack label code. This may also help the regular
optimization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:

drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]

When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.

Fixes: c56a8be7 ("qed: Add supported link and advertise link to display in ethtool.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.

[   35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[   35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14

[   35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[   35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[   35.254141] Workqueue: events work_for_cpu_fn
[   35.254144] Call trace:
[   35.254147]  dump_backtrace+0x0/0x2f0
[   35.254149]  show_stack+0x24/0x30
[   35.254154]  dump_stack+0x110/0x184
[   35.254157]  print_address_description+0x168/0x2b0
[   35.254160]  kasan_report+0x184/0x310
[   35.254162]  __asan_load2+0x7c/0xa0
[   35.254170]  hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[   35.254177]  hclge_tm_init_hw+0x794/0x9f0 [hclge]
[   35.254184]  hclge_tm_schd_init+0x48/0x58 [hclge]
[   35.254191]  hclge_init_ae_dev+0x778/0x1168 [hclge]
[   35.254196]  hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[   35.254206]  hns3_probe+0x88/0xa8 [hns3]
[   35.254210]  local_pci_probe+0x7c/0xf0
[   35.254212]  work_for_cpu_fn+0x34/0x50
[   35.254214]  process_one_work+0x4d4/0xa38
[   35.254216]  worker_thread+0x55c/0x8d8
[   35.254219]  kthread+0x1b0/0x1b8
[   35.254222]  ret_from_fork+0x10/0x1c

[   35.254224] The buggy address belongs to the page:
[   35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[   35.273835] flags: 0xfffff8000008000(head)
[   35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[   35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[   35.282012] page dumped because: kasan: bad access detected

[   35.282014] Memory state around the buggy address:
[   35.282017]  ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282019]  ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282022]                             ^
[   35.282024]  ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282026]  ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282028] ==================================================================
[   35.282029] Disabling lock debugging due to kernel taint
[   35.282747] hclge driver initialization finished.

Fixes: 67bf2541 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net: bql: better deal with GSO

While BQL bulk dequeue works well for TSO packets, it is
not very efficient as soon as GSO is involved.

On a GSO only workload (UDP or TCP), this patch series
can save about 8 % of cpu cycles on a 40Gbit mlx4 NIC,
by keeping optimal batching, and avoiding expensive
doorbells, qdisc requeues and reschedules.

This patch series :

- Add __netdev_tx_sent_queue() so that drivers
  can implement efficient BQL and xmit_more support.

- Implement a work around in dev_hard_start_xmit()
  for drivers not using __netdev_tx_sent_queue()

- changes mlx4 to use __netdev_tx_sent_queue()

v2: Tariq and Willem feedback addressed.
    added __netdev_tx_sent_queue() (Willem suggestion)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

doorbell only depends on xmit_more and netif_tx_queue_stopped()

Using __netdev_tx_sent_queue() avoids messing with BQL stop flag,
and is more generic.

This patch increases performance on GSO workload by keeping
doorbells to the minimum required.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before calling dev_hard_start_xmit(), upper layers tried
to cook optimal skb list based on BQL budget.

Problem is that GSO packets can end up comsuming more than
the BQL budget.

Breaking the loop is not useful, since requeued packets
are ahead of any packets still in the qdisc.

It is also more expensive, since next TX completion will
push these packets later, while skbs are not in cpu caches.

It is also a behavior difference with TSO packets, that can
break the BQL limit by a large amount.

Note that drivers should use __netdev_tx_sent_queue()
in order to have optimal xmit_more support, and avoid
useless atomic operations as shown in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When qdisc_run() tries to use BQL budget to bulk-dequeue a batch
of packets, GSO can later transform this list in another list
of skbs, and each skb is sent to device ndo_start_xmit(),
one at a time, with skb->xmit_more being set to one but
for last skb.

Problem is that very often, BQL limit is hit in the middle of
the packet train, forcing dev_hard_start_xmit() to stop the
bulk send and requeue the end of the list.

BQL role is to avoid head of line blocking, making sure
a qdisc can deliver high priority packets before low priority ones.

But there is no way requeued packets can be bypassed by fresh
packets in the qdisc.

Aborting the bulk send increases TX softirqs, and hot cache
lines (after skb_segment()) are wasted.

Note that for TSO packets, we never split a packet in the middle
because of BQL limit being hit.

Drivers should be able to update BQL counters without
flipping/caring about BQL status, if the current skb
has xmit_more set.

Upper layers are ultimately responsible to stop sending another
packet train when BQL limit is hit.

Code template in a driver might look like the following :

	send_doorbell = __netdev_tx_sent_queue(tx_queue, nr_bytes, skb->xmit_more);

Note that __netdev_tx_sent_queue() use is not mandatory,
since following patch will change dev_hard_start_xmit()
to not care about BQL status.

But it is highly recommended so that xmit_more full benefits
can be reached (less doorbells sent, and less atomic operations as well)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: fixes 2018-11-02

please apply one round of qeth fixes for -net.

Patch 1 is rather large and removes a use-after-free hazard from many of our
debug trace entries.
Patch 2 is yet another fix-up for the L3 subdriver's new IP address management
code.
Patch 3 and 4 resolve some fallout from the recent changes wrt how/when qeth
allocates its net_device.
Patch 5 makes sure we don't set reserved bits when building HW commands from
user-provided data.
And finally, patch 6 allows ethtool to play nice with new HW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the various identifiers for 25Gbit cards, and wires them up
into sysfs and ethtool.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ARP_{ADD,REMOVE}_ENTRY cmd structs contain reserved fields.
Introduce a common helper that doesn't raw-copy the user-provided data
into the cmd, but only sets those fields that are strictly needed for
the command.

This also sets the correct command length for ARP_REMOVE_ENTRY.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting the carrier 'on' for an unregistered netdevice doesn't update
its operstate. Fix this by delaying the update until the netdevice has
been registered.

Fixes: 91cc98f5 ("s390/qeth: remove duplicated carrier state tracking")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth only registers its netdevice when the qeth device is first set
online. Thus a device that has never been set online will trigger
a WARN ("network todo 'hsi%d' but state 0") in unregister_netdev() when
removed.

Fix this by protecting the unregister step, just like we already protect
against repeated registering of the netdevice.

Fixes: d3d1b205 ("s390/qeth: allocate netdevice early")
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sniffing mode for L3 HiperSockets requires that no IP addresses are
registered with the HW. The preferred way to achieve this is for
userspace to delete all the IPs on the interface. But qeth is expected
to also tolerate a configuration where that is not the case, by skipping
the IP registration when in sniffer mode.
Since commit 5f78e29c ("qeth: optimize IP handling in rx_mode callback")
reworked the IP registration logic in the L3 subdriver, this no longer
works. When the qeth device is set online, qeth_l3_recover_ip() now
unconditionally registers all unicast addresses from our internal
IP table.

While we could fix this particular problem by skipping
qeth_l3_recover_ip() on a sniffer device, the more future-proof change
is to skip the IP address registration at the lowest level. This way we
a) catch any future code path that attempts to register an IP address
   without considering the sniffer scenario, and
b) continue to build up our internal IP table, so that if sniffer mode
   is switched off later we can operate just like normal.

Fixes: 5f78e29c ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As Documentation/s390/s390dbf.txt states quite clearly, using any
pointer in sprinf-formatted s390dbf debug entries is dangerous.
The pointers are dereferenced whenever the trace file is read from.
So if the referenced data has a shorter life-time than the trace file,
any read operation can result in a use-after-free.

So rip out all hazardous use of indirect data, and replace any usage of
dev_name() and such by the Bus ID number.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there's no entry to drop in bucket that corresponds to the hash,
early_drop() should look for it in other buckets. But since it increments
hash instead of bucket number, it actually looks in the same bucket 8
times: hsize is 16k by default (14 bits) and hash is 32-bit value, so
reciprocal_scale(hash, hsize) returns the same value for hash..hash+7 in
most cases.

Fix it by increasing bucket number instead of hash and rename _hash
to bucket to avoid future confusion.

Fixes: 3e86638e ("netfilter: conntrack: consider ct netns in early_drop logic")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Vasily Khoruzhick <vasilykh@arista.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Unlike ip(6)tables, the ebtables nat table has no special properties.
This bug causes 'ebtables -A' to fail when using a target such as
'snat' (ebt_snat target sets ".table = "nat"').  Targets that have
no table restrictions work fine.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Otherwise, we hit a NULL pointer deference since handlers always assume
default timeout policy is passed.

  netlink: 24 bytes leftover after parsing attributes in process `syz-executor2'.
  kasan: CONFIG_KASAN_INLINE enabled
  kasan: GPF could be caused by NULL-ptr deref or user memory access
  general protection fault: 0000 [#1] PREEMPT SMP KASAN
  CPU: 0 PID: 9575 Comm: syz-executor1 Not tainted 4.19.0+ #312
  Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
  RIP: 0010:icmp_timeout_obj_to_nlattr+0x77/0x170 net/netfilter/nf_conntrack_proto_icmp.c:297

Fixes: c779e849 ("netfilter: conntrack: remove get_timeout() indirection")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Expose these functions to access conntrack protocol tracker netns area,
nfnetlink_cttimeout needs this.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The ip_set() macro is called when either ip_set_ref_lock held only
or no lock/nfnl mutex is held at dumping. Take this into account
properly. Also, use Pablo's suggestion to use rcu_dereference_raw(),
the ref_netlink protects the set.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

When IDLETIMER rule is added, sysfs file is created under
/sys/class/xt_idletimer/timers/
But some label name shouldn't be used.
".", "..", "power", "uevent", "subsystem", etc...
So that sysfs filename checking routine is needed.

test commands:
   %iptables -I INPUT -j IDLETIMER --timeout 1 --label "power"

splat looks like:
[95765.423132] sysfs: cannot create duplicate filename '/devices/virtual/xt_idletimer/timers/power'
[95765.433418] CPU: 0 PID: 8446 Comm: iptables Not tainted 4.19.0-rc6+ #20
[95765.449755] Call Trace:
[95765.449755]  dump_stack+0xc9/0x16b
[95765.449755]  ? show_regs_print_info+0x5/0x5
[95765.449755]  sysfs_warn_dup+0x74/0x90
[95765.449755]  sysfs_add_file_mode_ns+0x352/0x500
[95765.449755]  sysfs_create_file_ns+0x179/0x270
[95765.449755]  ? sysfs_add_file_mode_ns+0x500/0x500
[95765.449755]  ? idletimer_tg_checkentry+0x3e5/0xb1b [xt_IDLETIMER]
[95765.449755]  ? rcu_read_lock_sched_held+0x114/0x130
[95765.449755]  ? __kmalloc_track_caller+0x211/0x2b0
[95765.449755]  ? memcpy+0x34/0x50
[95765.449755]  idletimer_tg_checkentry+0x4e2/0xb1b [xt_IDLETIMER]
[ ... ]

Fixes: 0902b469 ("netfilter: xtables: idletimer target implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The function is called when rcu_read_lock() is held and not
when rcu_read_lock_bh() is held.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Florian Fainelli says:

====================
net: timeout fixes for GENET and SYSTEMPORT

This patch series fixes occasional transmit timeout around the time
the system goes into suspend. GENET and SYSTEMPORT have nearly the same
logic in that regard and were both affected in the same way.

Please queue up for stable, thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.

The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcm_sysport_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.

This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcm_sysport_netif_stop. There
are currently only two users of the bcm_sysport_netif_stop function:
close and suspend.

The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.

The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcm_sysport_netif_stop rather than
after it.

These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.

For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcm_sysport_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcm_sysport_netif_start so it is moved into the driver open service.

Fixes: 40755a0f ("net: systemport: add suspend and resume support")
Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.

The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcmgenet_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.

This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcmgenet_netif_stop. There
are currently only two users of the bcmgenet_netif_stop function:
close and suspend.

The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.

The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcmgenet_netif_stop rather than
after it.

These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.

For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcmgenet_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcmgenet_netif_start so it is moved into the driver open service.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the network becomes (partially) unavailable, say by disabling IPv6, the
background ACK transmission routine can get itself into a tizzy by
proposing immediate ACK retransmission.  Since we're in the call event
processor, that happens immediately without returning to the workqueue
manager.

The condition should clear after a while when either the network comes back
or the call times out.

Fix this by:

 (1) When re-proposing an ACK on failed Tx, don't schedule it immediately.
     This will allow a certain amount of time to elapse before we try
     again.

 (2) Enforce a return to the workqueue manager after a certain number of
     iterations of the call processing loop.

 (3) Add a backoff delay that increases the delay on deferred ACKs by a
     jiffy per failed transmission to a limit of HZ.  The backoff delay is
     cleared on a successful return from kernel_sendmsg().

 (4) Cancel calls immediately if the opening sendmsg fails.  The layer
     above can arrange retransmission or rotate to another server.

Fixes: 248f219c ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initialize mutex before use.  Avoid kernel complaint when
CONFIG_DEBUG_LOCK_ALLOC is enabled.

Fixes: b987e98e ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>