The index of TSF counters should follow HWBSSID.

Fixes: d8d59f66 ("mt76: mt7615: support 16 interfaces")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix register definitions for mac80211 stats reporting.
Move mib counter reset to mt7921_get_stats routine.

Fixes: 163f4d22 ("mt76: mt7921: add MAC support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix the following coccicheck warnings:

./drivers/net/wireless/mediatek/mt76/mt7921/mac.c:1402:2-3: Unneeded
semicolon.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Similar to mt7921, fix 802.11 aggr len debugfs reporting for mt7915 driver.

Fixes: e57b7901 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix register definitions for 802.11 aggr length histogram estimation.

Fixes: 474a9f21 ("mt76: mt7921: add debugfs support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Similar to the issue fixed in mt7921_coredump_work, fix a possible memory
leak in mt7615_coredump_work routine.

Fixes: d2bf7959 ("mt76: mt7663: introduce coredump support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For AP and Client mode, the hardware can pass received packets
as 802.3 frames that can be passed to the network stack as-is.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Set skb->ip_summed to CHECKSUM_UNNECESSARY if the hardware has validated
the IP and TCP/UDP checksum
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Enable hw rx-amsdu de-aggregation support.
This is a preliminary patch to enable rx checksum offload.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

With threaded NAPI, the rx handler function is no longer bound to the CPU that
fired the interrupt, which significantly helps to spread the workload over
multiple CPUs, especially when multiple devices are using threaded NAPI at the
same time.
Exclude the tx handler from threaded NAPI by using a separate dummy netdev.
The work is small and short-lived enough that it makes more sense to run it in
softirq instead of creating a dedicated thread
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Update sched_scan command usage according to the current firmware
submitted into linux-firmware.git.

Fixes: 80fc1e37 ("mt76: mt7921: rely on mt76_connac_mcu module for sched_scan and hw_scan")
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

add flush operation to make sure cfg80211_mlme_deauth is able to flush
the deauthtication frame into air immediately.
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Since the related rx bitrate fields have been moved to group3 in Rxv,
fix rx bitrate statistics in mt7921_mac_fill_rx routine.

Fixes: 163f4d22 ("mt76: mt7921: add MAC support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use proper value for ht40 mode configuration in mt76_connac_mcu_uni_add_bss
routine and not ht20 one

Fixes: d0e274af ("mt76: mt76_connac: create mcu library")
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Current firmware only supports new api for enabling hardware beacon filter.

Fixes: 1d8efc74 ("mt76: mt7921: introduce Runtime PM support")
Beacon filter cmd have to rely on the associatied access point's beacon
interval and DTIM information.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix possible memory leak in mt7921_coredump_work.

Fixes: 1c099ab4 ("mt76: mt7921: add MCU support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Any pcie access should happen in pci D0 state and we should give ownership
back to the device at the end of the suspend procedure.

Fixes: 1d8efc74 ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use PCI standard defines.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

As done for mt76_connac_mcu_alloc_wtbl_req, even if this is not a real
bug since mt7915_mcu_alloc_wtbl_req routine can fails just if nskb is NULL,
always check return value from mt7915_mcu_alloc_wtbl_req in order to avoid
possible future mistake.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Even if this is not a real bug since mt76_connac_mcu_alloc_wtbl_req routine
can fails just if nskb is NULL , always check return value from
mt76_connac_mcu_alloc_wtbl_req in order to avoid possible future
mistake.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When operating two VAP on a MT7610 with encryption (PSK2, SAE, OWE),
only the first one to be created will transmit properly encrypteded
frames.

All subsequently created VAPs will sent out frames with the payload left
unencrypted, breaking multicast traffic (ICMP6 NDP) and potentially
disclosing information to a third party.

Disable GTK offloading and encrypt these frames in software to
circumvent this issue. THis only seems to be necessary on MT7610 chips,
as MT7612 is not affected from our testing.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Simplify WTBL defines.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Get rid of the following definitions in mt7921/mcu.h since they are not
actually used:
- MT7921_WTBL_UPDATE_MAX_SIZE
- MT7921_STA_UPDATE_MAX_SIZE
- MT7921_WTBL_UPDATE_BA_SIZE
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

In mt7921_pm_set() the variable "ret" is initialized to zero
and then returned. Remove it and return zero.
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Notify mac80211 mt7921 devices support random mac address during hw
frequency scanning
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

EEPROM blobs for MT7613BE radios start with (little endian) 0x7663,
which is also the PCI device ID for this device. The EEPROM is required
for the radio to work at useful power levels, otherwise only the lowest
power level is available.
Suggested-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The first pointer in the txp needs to be unmapped as well, otherwise it will
leak DMA mapping entries
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: 27d5c528 ("mt76: fix double DMA unmap of the first buffer on 7615/7915")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The first pointer in the txp needs to be unmapped as well, otherwise it will
leak DMA mapping entries

Fixes: 27d5c528 ("mt76: fix double DMA unmap of the first buffer on 7615/7915")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

There were multiple issues in the current key set/remove code:
- deleting a key with the previous key index deletes the current key
- BIP key would only be uploaded correctly initially and corrupted on rekey

Rework the code to better keep track of multiple keys and check for the
key index before deleting the current key
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For AP and Client mode, the hardware can pass received packets as 802.3 frames
that can be passed to the network stack as-is.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Set skb->ip_summed to CHECKSUM_UNNECESSARY if the hardware has validated
the IP and TCP/UDP checksum
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Enable hw rx-amsdu de-aggregation support available in 7915 devices.
This is a preliminary patch to enable rx checksum offload
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Do not try to access the header when receiving them
Signed-off-by: Felix Fietkau <nbd@nbd.name>

There are a couple of warnings in this driver when building with W=1:

drivers/net/wireless/intel/iwlegacy/common.c: In function 'il_power_set_mode':
drivers/net/wireless/intel/iwlegacy/common.c:1195:60: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
 1195 |                                 il->chain_noise_data.state);
      |                                                            ^
drivers/net/wireless/intel/iwlegacy/common.c: In function 'il_do_scan_abort':
drivers/net/wireless/intel/iwlegacy/common.c:1343:57: error: suggest braces around empty body in an 'else' statement [-Werror=empty-body]

Change the empty debug macros to no_printk(), which avoids the
warnings and adds useful format string checks.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210322104343.948660-3-arnd@kernel.org

Notify mac80211 the mt7601u chipset support 802.11 TDLS. The feature has
been tested with a mt7610u peer.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/8f9fd662cdbbb70ba896f1bea80e696b15011d3f.1614536496.git.lorenzo@kernel.org

Currently the expression ~nic_conf1 is always true because nic_conf1
is a u16 and according to 6.5.3.3 of the C standard the ~ operator
promotes the u16 to an integer before flipping all the bits. Thus
the top 16 bits of the integer result are all set so the expression
is always true.  If the intention was to flip all the bits of nic_conf1
then casting the integer result back to a u16 is a suitabel fix.

Interestingly static analyzers seem to thing a bitwise ! should be
used instead of ~ for this scenario, so I think the original intent
of the expression may need some extra consideration.

Addresses-Coverity: ("Logical vs. bitwise operator")
Fixes: c869f77d ("add mt7601u driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210225183241.1002129-1-colin.king@canonical.com

The sscanf() function returns the number of matches (0 or 1 in this
case).  It doesn't return error codes.  We should return -EINVAL if the
string is invalid

Fixes: c376c1fc ("rtw88: add h2c command in debugfs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YE8nmatMDBDDWkjq@mwanda

While WL scan, WL is more high priority than BT. The packets from AP
will be a big interference to A2DP. It will lead to A2DP stutters. Stop
answering CTS to AP to decrease AP's packets Tx while WL scan + WL busy.
Enable BT AFH feature to make BT leave away from WL channel.

Desired BT firmware BT-COEX version: 0x1c
Desired WL firmware version: 9.9.x
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210319054218.3319-8-pkshih@realtek.com

Fix power tracking issue by replacing unnecessary IQ calibration
with LC calibration.
When thermal difference exceeds limitation, let RF circuit adjsut
its characteristic to fit in current environment.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210319054218.3319-6-pkshih@realtek.com

update tx power limits to RF v40 and apply fix on FCC's channel 12 and 13,
so change the patch level to 1.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210319054218.3319-5-pkshih@realtek.com