- 16 Sep, 2014 40 commits
-
-
Sreekanth Reddy authored
Copyright in driver sources is updated for year the 2014. Signed-off-by:
Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Christoph Hellwig <hch@lst.de>
-
Sreekanth Reddy authored
Below is the change set in MPI2.5 Rev H specification and 2.00.32 header files 1) Added reserved fields to IO Unit Page 7 for future use. 2) Added optional functionality to IOCInit Request so that the host may specify a separate base address for each Reply Descriptor Post Queue. IOC support for this is indicated using a new IOCCapabilities bit in the IOCFacts Reply. 3) Added Toolbox Console Text Display Tool The host uses the Console Text Display Tool to send a string to IOC's Console using different console types (eg: UART serial terminal or Ethernet terminal). 4) Firmware images can now be signed using an encrypted hash. 5) Added MPI2_SAS_OP_TRANSMIT_PORT_SELECT_SIGNAL 6) Added more details about configuration page restrictions when Host Based Discovery is enabled Enabling host based discovery affects the availability of some configuration pages and events. The SAS Expander, SAS Device, and SAS Enclosure configuration pages are not available from the IOC. The IOC returns an error status to any Configuration Request message attempting to access these pages. The IOC does not send the SAS Discovery Event, the SAS Topology Change List Event, or the SAS Enclosure Device Status Change Event when host based discovery is enabled. 7) Bit 13 of the SAS IO Unit Page 1 ControlFlags field is now obsolete. It was used to enable limiting direct attached SATA maximum link rate to 1.5 Gbps. Signed-off-by:
-
Sreekanth Reddy authored
Bump mpt3sas driver version to 03.100.00.00. Signed-off-by:
-
Sreekanth Reddy authored
Added code to send an SEP message that turns off the Predictive Failure LED when a drive is removed (if Predictive Failure LED was turned on). Added a new flag 'pfa_led_on' per device that tracks the status of Predictive Failure LED. When the drive is removed, this flag is checked and sends an SEP message to turn off the respective Predictive Failure LED. Signed-off-by:
-
Sreekanth Reddy authored
Below is the change set in MPI2.5 Rev G specification and 2.00.31 header files 1) Added SCSIStatusQualifier to SCSI IO Error Reply message. 2) Added ATA Security Freeze Lock to IO Unit Page 1 Flags field. 3) Added Allow Protection Information bit for IR Volume Create. Signed-off-by:
-
Sreekanth Reddy authored
Bump mpt2sas driver version to 18.100.00.00. Signed-off-by:
-
Sreekanth Reddy authored
mpt2sas: Get IOC_FACTS information using handshake protocol only after HBA card gets into READY or Operational state. Driver initialization fails if driver tries to send IOC facts request message when the IOC is in reset or in a fault state. This patch will make sure that 1.Driver to send IOC facts request message only if HBA is in operational or ready state. 2.If IOC is in fault state, a diagnostic reset would be issued. 3.If IOC is in reset state then driver will wait for 10 seconds to exit out of reset state. If the HBA continues to be in reset state, then the HBA wouldn't be claimed by the driver. Signed-off-by:
-
Sreekanth Reddy authored
Up to now, Driver allocates a single contiguous block of memory pool for all reply queues and passes down a single address in the ReplyDescriptorPostQueueAddress field of the IOC Init Request Message to the firmware. When firmware receives this address, it will program each of the Reply Descriptor Post Queue registers, as each reply queue has its own register. Thus the firmware, starting from a base address it determines the starting address of the subsequent reply queues through some simple arithmetic calculations. The size of this contiguous block of memory pool is directly proportional to number of MSI-X vectors and the HBA queue depth. For example higher MSIX vectors requires larger contiguous block of memory pool. But some of the OS kernels are unable to allocate this larger contiguous block of memory pool. So, the proposal is to allocate memory independently for each Reply Queue and pass down all of the addresses to the firmware. Then the firmware will just take each address and program the value into the correct register. When HBAs with older firmware(i.e. without RDPQ capability) is used with this new driver then the max_msix_vectors value would be set to 8 by default. Change_set in v1: 1. Declared _base_get_ioc_facts() function at the beginning of the mpt2sas_base.c file instead of moving all these functions before mpt2sas_base_map_resources() function a. _base_wait_for_doorbell_int() b. _base_wait_for_doorbell_ack() c. _base_wait_for_doorbell_not_used() d. _base_handshake_req_reply_wait() e. _base_get_ioc_facts() 2. Initially set the consistent DMA mask to 32 bit and then change it to 64 bit mask after allocating RDPQ pools by calling the function _base_change_consistent_dma_mask. This is to ensure that all the upper 32 bits of RDPQ entries's base address to be same. 3. Reduced the redundancy between the RDPQ and non-RDPQ support in these following functions a. _base_release_memory_pools() b. _base_allocate_memory_pools() c. _base_send_ioc_init() d. _base_make_ioc_operational() Signed-off-by: -
Sreekanth Reddy authored
A type casting error caused the max volume LBA to be truncated from 64 to 32 bits. The virtual LBA would also get truncated to 32 bits in the case of a 16-byte READ/WRITE command. Rewrite entire function to get rid of code duplication and type casts. Use get/put_unaligned wrappers to extract and replace the LBA field in the MPI request CDB. Signed-off-by:
-
Sreekanth Reddy authored
Bump mpt2sas driver version to 17.100.00.00 Signed-off-by:
-
Sreekanth Reddy authored
Added code to send a SEP message that turns off the Predictive Failure LED when a drive is removed (if Predictive Failure LED was turned on). Added a new flag 'pfa_led_on' per device that tracks the status of Predictive Failure LED. When the drive is removed, this flag is checked and sends the SEP message to turn off the respective Predictive Failure LED. Signed-off-by:
-
Sreekanth Reddy authored
Copyright in driver sources is updated for year the 2014. Signed-off-by:
-
Sreekanth Reddy authored
Below is the change set in MPI2 Rev Y specification and in 2.00.17 header files 1) Added SCSIStatusQualifier to SCSI IO Error Reply message. 2) Added ATA Security Freeze Lock to IO Unit Page 1 Flags field. Below is the change set in MPI2 Rev Z specification and in 2.00.19 header files 1) Added reserved fields to IO Unit Page 7 for future use. 2) Added optional functionality to IOCInit Request so that the host may specify a separate base address for each Reply Descriptor Post Queue. IOC support for this is indicated using a new IOCCapabilities bit in the IOCFacts Reply. 3) Added Toolbox Console Text Display Tool The host uses the Console Text Display Tool to send a string to IOC's Console using different console types (eg: UART serial terminal or Ethernet terminal). The copyright in the mpi files is updated for year 2014 Signed-off-by:
-
Sreekanth Reddy authored
Added driver module parameter max_msix_vectors. Using this module parameter the maximum number of MSI-X vectors could be set. The number of MSI-X vectors used would be the minimum of MSI-X vectors supported by the HBA, the number of CPU cores and the value set to max_msix_vectors module parameters. Signed-off-by:
-
Tej Parkash authored
Signed-off-by:
Tej Parkash <tej.parkash@qlogic.com> Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Acked-by:
Eddie Wai <eddie.wai@broadcom.com> Signed-off-by:
-
Chad Dupuis authored
This patch is based on a problem and solution from Maurizio Lombardi where bnx2fc isn't consistent in which device struct we using for DMA map and unmap operations. Make them consistent by using dma_sg_unmap in bnx2fc_unmap_sg_list like bnx2fc_map_sg. Reviewed-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
James Smart authored
Update lpfc version to driver version 10.4.8000.0 Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
Dick Kennedy <dick.kennedy@emulex.com> Signed-off-by:
-
James Smart authored
Fix for handling unmapped ndlp in target reset handler Signed-off-by:
-
James Smart authored
Fixed Low priority issues from lpfc given by fortify source code scan. Signed-off-by:
-
James Smart authored
Fixed High priority issues from lpfc given by fortify source code scan. Signed-off-by:
-
James Smart authored
Fix crash from page fault caused by use after rport delete. Signed-off-by:
-
James Smart authored
Fix locking issues with abort data paths Signed-off-by:
-
James Smart authored
Fix race between LOGO/PLOGI handling causing NULL pointer Signed-off-by:
-
James Smart authored
Fix IP Reset processing - wait for RDY before proceeding Signed-off-by:
-
James Smart authored
Fix quarantined XRI recovery qualifier state in link bounce Signed-off-by:
-
James Smart authored
Fix discovery timeout during nameserver login Signed-off-by:
-
Alexander Gordeev authored
As result of deprecation of MSI-X/MSI enablement functions pci_enable_msix() and pci_enable_msi_block() all drivers using these two interfaces need to be updated to use the new pci_enable_msi_range() or pci_enable_msi_exact() and pci_enable_msix_range() or pci_enable_msix_exact() interfaces. Signed-off-by:
Alexander Gordeev <agordeev@redhat.com> Reviewed-by:
-
Daniel Borkmann authored
In prandom we have already reseeding mechanisms that trigger periodically from a much better entropy source than just feeding in jiffies through lpfc_mbx_cmpl_fcf_scan_read_fcf_rec() [what a function name 8-)]. Therefore, just remove this. Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Reviewed-by:
-
Manuel Schölling authored
To be future-proof and for better readability the time comparisons are modified to use time_after() instead of plain, error-prone math. Signed-off-by:
Manuel Schölling <manuel.schoelling@gmx.de> Reviewed-by:
-
Joe Perches authored
Use the zeroing function instead of dma_alloc_coherent & memset(,0,) Signed-off-by:
Joe Perches <joe@perches.com> Reviewed-by:
-
Rashika Kheria authored
[PATCH 26/55] scsi: Mark function as static in lpfc/lpfc_bsg.c Mark function as static in lpfc/lpfc_bsg.c because it is not used outside this file. This eliminates the following warning in lpfc/lpfc_bsg.c: drivers/scsi/lpfc/lpfc_bsg.c:3348:1: warning: no previous prototype for ‘lpfc_bsg_issue_mbox_cmpl’ [-Wmissing-prototypes] Signed-off-by:
Rashika Kheria <rashika.kheria@gmail.com> Reviewed-by:
Josh Triplett <josh@joshtriplett.org> Reviewed-by:
-
Rashika Kheria authored
Mark functions as static in lpfc/lpfc_scsi.c because they are not used outside this file. This eliminates the following warnings in lpfc/lpfc_scsi.c: drivers/scsi/lpfc/lpfc_scsi.c:299:1: warning: no previous prototype for ‘lpfc_change_queue_depth’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_scsi.c:795:1: warning: no previous prototype for ‘lpfc_sli4_post_scsi_sgl_list’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_scsi.c:3019:1: warning: no previous prototype for ‘lpfc_bg_crc’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_scsi.c:3035:1: warning: no previous prototype for ‘lpfc_bg_csum’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_scsi.c:3048:1: warning: no previous prototype for ‘lpfc_calc_bg_err’ [-Wmissing-prototypes] Signed-off-by:
-
Rashika Kheria authored
Mark functions as static in lpfc/lpfc_init.c because they are not used outside this file. This eliminates the following warning in lpfc/lpfc_init.c: drivers/scsi/lpfc/lpfc_init.c:652:1: warning: no previous prototype for ‘lpfc_hba_init_link’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_init.c:753:1: warning: no previous prototype for ‘lpfc_hba_down_link’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_init.c:3434:1: warning: no previous prototype for ‘lpfc_sli4_fcf_redisc_wait_tmo’ [-Wmissing-prototypes] Signed-off-by:
-
Rashika Kheria authored
Mark functions as static in lpfc/lpfc_hbadisc.c because they are not used outside this file. This eliminates the following warnings in lpfc/lpfc_hbadisc.c: drivers/scsi/lpfc/lpfc_hbadisc.c:2047:5: warning: no previous prototype for ‘lpfc_sli4_fcf_pri_list_add’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_hbadisc.c:2681:1: warning: no previous prototype for ‘lpfc_init_vfi_cmpl’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_hbadisc.c:4432:1: warning: no previous prototype for ‘lpfc_nlp_logo_unreg’ [-Wmissing-prototypes] Signed-off-by:
-
Rashika Kheria authored
[PATCH 22/55] scsi: Mark functions as static in lpfc/lpfc_sli.c Mark functions as static in lpfc/lpfc_sli.c because they are not used outside this file. This eliminates the following warnings in lpfc/lpfc_sli.c: drivers/scsi/lpfc/lpfc_sli.c:13867:1: warning: no previous prototype for ‘lpfc_sli4_alloc_xri’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_sli.c:13897:1: warning: no previous prototype for ‘__lpfc_sli4_free_xri’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_sli.c:14317:1: warning: no previous prototype for ‘lpfc_update_rcv_time_stamp’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_sli.c:14786:1: warning: no previous prototype for ‘lpfc_sli4_handle_unsol_abort’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_sli.c:15331:1: warning: no previous prototype for ‘__lpfc_sli4_free_rpi’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_sli.c:15769:1: warning: no previous prototype for ‘lpfc_check_next_fcf_pri_level’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_sli.c:16000:1: warning: no previous prototype for ‘lpfc_mbx_cmpl_redisc_fcf_table’ [-Wmissing-prototypes] Signed-off-by:
-
Hiral Shah authored
1) Assgning FIP_ALL_FCF_MACS to fcoe_all_fcfs allows VLAN request to be sent to correct Mac address for VLAN Discovery otherwise VLAN request will be sent to invalid address hence FLOGI never happens. 2) Simplify the copy_and_format_trace_data code and log the correct Link event for fnic control path tracing in case of link status UP->UP. 3) Increment Fnic driver version Signed-off-by:
Hiral Shah <hishah@cisco.com> Signed-off-by:
Sesidhar Baddela <sebaddel@cisco.com> Signed-off-by:
-
Joe Lawrence authored
The PCI register read checking introduced in commit fe1b806f ("qla2xxx: Disable adapter when we encounter a PCI disconnect") is active during driver probe. Hold off scheduling any board removal until the driver probe has completed. This ensures that the the board_disable work structure is initialized and more importantly, avoids racing qla2x00_probe_one. Signed-off-by:
Joe Lawrence <joe.lawrence@stratus.com> Acked-by:
-
Joe Lawrence authored
Introduce mutual exclusion between the qla2xxx_remove_one PCI driver callback and qla2x00_disable_board_on_pci_error, which is scheduled as board_disable work by qla2x00_check_reg{32,16}_for_disconnect: * Leave the driver-specific data attached to the underlying PCI device intact in qla2x00_disable_board_on_pci_error, so that qla2x00_remove_one has enough breadcrumbs to determine that any board_disable work has been completed. * In qla2xxx_remove_one, set a bit to prevent any subsequent board_disable work from scheduling, then cancel and wait until pending work has completed. * Reuse the PCI device enable count check in qla2x00_remove_one to determine if board_disable has occured. The original purpose of this check was unnecessary since the driver remove function wasn't called when the probe fails. Signed-off-by: -
Joe Lawrence authored
There are various callers of qla2x00_check_reg{32,16}_for_disconnect that may schedule board removal on PCI-disconnect. Test-and-set a dedicated flag before scheduling board_disable so it is invoked only once. Signed-off-by: -
Joe Lawrence authored
Add an uint16_t variant of qla2x00_check_reg_for_disconnect and use these routines to check and schedule a PCI-disconnected board from a centralized place. Signed-off-by:
-
