Add helper smcr_lgr_link_deactivate_all() and eliminate duplicate code.
In smc_lgr_free(), clear the smc-r links before smc_lgr_free_bufs() is
called so buffers are already prepared for free. The usage of the soft
parameter in __smc_lgr_terminate() is no longer needed, smc_lgr_free()
can be called directly. smc_lgr_terminate_sched() and
smc_smcd_terminate() set lgr->freeing to indicate that the link group
will be freed soon to avoid unnecessary schedules of the free worker.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow to set the reason code for the link group termination, and set
meaningful values before termination processing is triggered. This
reason code is sent to the peer in the final delete link message.
When the LLC request or response layer receives a message type that was
not handled, drop a warning and terminate the link group.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New connections must not be assigned to asymmetric links. Add asymmetric
link tagging using new link variable link_is_asym. The new helpers
smcr_lgr_set_type() and smcr_lgr_set_type_asym() are called to set the
state of the link group, and tag all links accordingly.
smcr_lgr_conn_assign_link() respects the link tagging and will not
assign new connections to links tagged as asymmetric link.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For new connections, assign a link from the link group, using some
simple load balancing.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add smc_llc_send_message_wait() which uses smc_wr_tx_send_wait() to send
an LLC message and waits for the message send to complete.
smc_llc_send_link_delete_all() calls the new function to send an
DELETE_LINK,ALL LLC message. The RFC states that the sender of this type
of message needs to wait for the completion event of the message
transmission and can terminate the link afterwards.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce smc_wr_tx_send_wait() to send an IB message and wait for the
tx completion event of the message. This makes sure that the message is
no longer in-flight when the function returns.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call smc_cdc_msg_validate() when a CDC message with the failover
validation bit enabled was received. Validate that the sequence number
sent with the message is one we already have received. If not, messages
were lost and the connection is terminated using a new abort_work.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a connection is switched to a new link then a link validation
message must be sent to the peer over the new link, containing the
sequence number of the last CDC message that was sent over the old link.
The peer will validate if this sequence number is the same or lower then
the number he received, and abort the connection if messages were lost.
Add smcr_cdc_msg_send_validation() to send the message validation
message and call it when a connection was switched in
smc_switch_cursor().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add smc_switch_conns() to switch all connections from a link that is
going down. Find an other link to switch the connections to, and
switch each connection to the new link. smc_switch_cursor() updates the
cursors of a connection to the state of the last successfully sent CDC
message. When there is no link to switch to, terminate the link group.
Call smc_switch_conns() when a link is going down.
And with the possibility that links of connections can switch adapt CDC
and TX functions to detect and handle link switches.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a link goes down and all connections of this link need to be
switched to an other link then the producer cursor and the sequence of
the last successfully sent CDC message must be known. Add the two fields
to the SMC connection and update it in the tx completion handler.
And to allow matching of sequences in error cases reset the seqno to the
old value in smc_cdc_msg_send() when the actual send failed.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Updates for net-next.

This patchset includes these main changes:

1. Firmware spec. update.
2. Context memory sizing improvements for the hardware TQM block.
3. ethtool chip reset improvements and fixes for correctness.
4. Improve L2 doorbell mapping by mapping only up to the size specified
by firmware.  This allows the RoCE driver to map the remaining doorbell
space for its purpose, such as write-combining.
5. Improve ethtool -S channel statistics by showing only relevant ring
counters for non-combined channels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, ethtool -S shows all TX/RX ring counters whether the
channel is combined, RX, or TX.  The unused counters will always be
zero.  Improve it by showing only the relevant counters if the channel
is RX or TX.  If the channel is combined, the counters will be shown
exactly the same as before.

[ MChan: Lots of cleanups and simplifications on Rajesh's original
code]
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will allow the RX and TX ring statistics to be separated if needed.
In the next patch, we'll be able to only display RX or TX statistcis if
the channel is RX only or TX only.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently have 3 software ring counters, rx_l4_csum_errors,
rx_buf_errors, and missed_irqs.  The 1st two are RX counters and the
last one is a common counter.  Organize them into 2 structures
bnxt_rx_sw_stats and bnxt_cmn_sw_stats.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The purpose of this is to inform the RDMA driver the size of the doorbell
BAR that the L2 driver has mapped and the portion that is mapped
uncacheable.  The unchaeable portion is shared with the RoCE driver.
Any remaining unmapped doorbell BAR can be used by the RDMA driver for
its own purpose.  Currently, the entire L2 portion is mapped uncacheable.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Read the L2 doorbell size from the firmware and only map the portion
of the doorbell BAR for L2 use.  This will leave the remaining doorbell
BAR available for the RoCE driver to use.  The RoCE driver can map
the remaining portion as write-combining to support the push feature.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver provides completion ring or NQ doorbell offset for each
MSIX entry requested by the RDMA driver.  The NQ offset on 57500
chips is different than legacy chips.  Set it correctly based on
chip type for correctness.  The RDMA driver is ignoring this field
for the 57500 chips so it is not causing any problem.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define the 57500 chip doorbell offsets instead of using the magic
values in the C file.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kernel log messages for failed AP reset commands should be suppressed.
These are expected to fail on devices that do not have an AP.  Add
missing driver reload message after AP reset and log it in a common
way without duplication.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool ABI specifies that the reset operation should only clear
the flags that were actually reset. Setting the flags to zero after
a chip reset violates this because it does not include resetting the
application processor complex. Similarly, components that are not yet
defined are also not necessarily being reset.

The fact that chip reset does not cover the AP also means that it is
inappropriate to treat these two components exclusively of one another.
The ABI provides a mechanism to report a failure to reset independent
components via the returned bitmask, so it is also wrong to fail hard
if one of a set of independent resets is not possible.

It is incorrect to rely on the passed by reference flags in bnxt_reset(),
which are being updated as components are reset. The initially requested
value should be used instead so that hard errors do not propagate if any
earlier components could have been reset successfully.

Note, AP and chip resets are global in nature. Dedicated resets are
thus not currently supported.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The case statement in bnxt_firmware_reset() dangerously mixes types.
This patch separates the application processor and whole chip resets
from the rest such that the selection is performed on a pure type.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract bnxt_hwrm_firmware_reset() for performing firmware reset
operations. This new helper function will be used in a subsequent
patch to separate unrelated reset types out of bnxt_firmware_reset().
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The firmware does not expect the CRC to be included in the length
passed from the driver.  The firmware always configures the chip
to strip out the CRC.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current formulas to calculate the TQM slow path and fast path ring
context memory sizes are not quite correct.  TQM slow path entry is
array index 0 of ctx->tqm_mem[].  The other array entries are for fast
path.  Fix these sizes according to latest firmware spec. for 57500 and
newer chips.

Fixes: 3be8136c ("bnxt_en: Initialize context memory to the value specified by firmware.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer firmware spec. will specify the number of TQM rings to allocate
context memory for.  Use the firmware specified value and fall back
to the old value derived from bp->max_q if it is not available.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes include additional statistics, ECN support, context memory
interface change for better TQM context memory sizing, firmware
health status definitions, etc.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Karsten Graul says:

====================
net/smc: add and delete link processing

These patches add the 'add link' and 'delete link' processing as
SMC server and client. This processing allows to establish and
remove links of a link group dynamically.

v2: Fix mess up with unused static functions. Merge patch 8 into patch 4.
    Postpone patch 13 to next series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

As SMC server, when a second link was deleted, trigger the setup of an
asymmetric link. Do this by enqueueing a local ADD_LINK message which
is processed by the LLC layer as if it were received from peer. Do the
same when a new IB port became active and a new link could be created.
smc_llc_srv_add_link_local() enqueues a local ADD_LINK message.
And smc_llc_srv_delete_link_local() is used the same way to enqueue a
local DELETE_LINK message. This is used when an IB port is no longer
active.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add smc_llc_process_srv_delete_link() to process a DELETE_LINK request
as SMC server. When the request is to delete ALL links then terminate
the whole link group. If not, find the link to delete by its link_id,
send the DELETE_LINK request LLC message and wait for the response.
No matter if a response was received, clear the deleted link and update
the link group state.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add smc_llc_process_cli_delete_link() to process a DELETE_LINK request
as SMC client. When the request is to delete ALL links then terminate
the whole link group. If not, find the link to delete by its link_id,
send the DELETE_LINK response LLC message and then clear the deleted
link. Finally determine and update the link group state.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a work that is scheduled when a new DELETE_LINK LLC request is
received. The work will call either the SMC client or SMC server
DELETE_LINK processing.
And use the LLC flow framework to process incoming DELETE_LINK LLC
messages, scheduling the llc_del_link_work for those events.
With these changes smc_lgr_forget() is only called by one function and
can be migrated into smc_lgr_cleanup_early().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a link group moved from asymmetric to symmetric state then the
dangling asymmetric link can be deleted. Add smc_llc_find_asym_link() to
find the respective link and add smc_llc_delete_asym_link() to delete
it.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch finalizes the ADD_LINK processing of new links. Send the
CONFIRM_LINK request to the peer, receive the response and set link
state to ACTIVE.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Part of SMC server new link establishment is the exchange of rkeys for
used buffers.
Loop over all used RMB buffers and send ADD_LINK_CONTINUE LLC messages
to the peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

First set of functions to process an ADD_LINK LLC request as an SMC
server. Find an alternate IB device, determine the new link group type
and get the index for the new link. Then initialize the link and send
the ADD_LINK LLC message to the peer. Save the contents of the response,
ready the link, map all used buffers and register the buffers with the
IB device. If any error occurs, stop the processing and clear the link.
And call smc_llc_srv_add_link() in af_smc.c to start second link
establishment after the initial link of a link group was created.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch finalizes the ADD_LINK processing of new links. Receive the
CONFIRM_LINK request from peer, complete the link initialization,
register all used buffers with the IB device and finally send the
CONFIRM_LINK response, which completes the ADD_LINK processing.
And activate smc_llc_cli_add_link() in af_smc.c.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Part of the SMC client new link establishment process is the exchange of
rkeys for all used buffers.
Add new LLC message type ADD_LINK_CONTINUE which is used to exchange
rkeys of all current RMB buffers. Add functions to iterate over all
used RMB buffers of the link group, and implement the ADD_LINK_CONTINUE
processing.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

First set of functions to process an ADD_LINK LLC request as an SMC
client. Find an alternate IB device, determine the new link group type
and get the index for the new link. Then ready the link, map the buffers
and send an ADD_LINK LLC response. If any error occurs, send a reject
LLC message and terminate the processing.
Add smc_llc_alloc_alt_link() to find a free link index for a new link,
depending on the new link group type.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sameeh Jubran says:

====================
Enhance current features in ena driver

Difference from v2:
* dropped patch "net: ena: move llq configuration from ena_probe to ena_device_init()"
* reworked patch ""net: ena: implement ena_com_get_admin_polling_mode() to drop the prototype

Difference from v1:
* reodered paches #01 and #02.
* dropped adding Rx/Tx drops to ethtool in patch #08

V1:
This patchset introduces the following:
* minor changes to RSS feature
* add total rx and tx drop counter
* add unmask_interrupt counter for ethtool statistics
* add missing implementation for ena_com_get_admin_polling_mode()
* some minor code clean-up and cosmetics
* use SHUTDOWN as reset reason when closing interface
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract code to ena_indirection_table_set() to make
the code cleaner.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>