The Kconfig currently controlling compilation of this code is:

init/Kconfig:config BPF_SYSCALL
init/Kconfig:   bool "Enable bpf() system call"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

Note that MODULE_ALIAS is a no-op for non-modular code.

We replace module.h with init.h since the file does use __init.

Cc: Alexei Starovoitov <ast@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

idx can be returned as -ENOSPC, so we should check for this first
before using it as an index into nn->vxlan_usecnt[] to avoid an
out of bounds array offset read.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable lan91x adapters in some ARM machines and models
when booted with an ACPI kernel.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some comments weren't updated to reflect the renaming of ndo's and the
change of arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As requested by Scott, removing him.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using a combination if #if conditionals and goto labels to unwind
tunnel4_init seems unwieldy. This patch takes a simpler approach of
directly unregistering previously registered protocols when an error
occurs.

This fixes a number of problems with the current implementation
including the potential presence of labels when they are unused
and the potential absence of unregister code when it is needed.

Fixes: 8afe97e5 ("tunnels: support MPLS over IPv4 tunnels")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: implement rfc7496 in sctp

This patchset implements "Additional Policies for the Partially Reliable
Stream Control Transmission Protocol Extension" described on RFC7496.

The Partially Reliable SCTP (PR-SCTP) extension defined in [RFC3758]
provides a generic method for senders to abandon user messages. The
decision to abandon a user message is sender side only, and the exact
condition is called a "PR-SCTP policy". This patchset implements 3
policies:

 1. Timed Reliability:  This allows the sender to specify a timeout for
    a user message after which the SCTP stack abandons the user message.

 2. Limited Retransmission Policy:  Allows limitation of the number of
    retransmissions.

 3. Priority Policy:  Allows removal of lower-priority messages if space
    for higher-priority messages is needed in the send buffer.

Patch 1-3 add some sockopts in sctp to set/get pr_sctp policy status.
Patch 4-6 implement these 3 policies one by one.
====================
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

prsctp PRIO policy is a policy to abandon lower priority chunks when
asoc doesn't have enough snd buffer, so that the current chunk with
higher priority can be queued successfully.

Similar to TTL/RTX policy, we will set the priority of the chunk to
prsctp_param with sinfo->sinfo_timetolive in sctp_set_prsctp_policy().
So if PRIO policy is enabled, msg->expire_at won't work.

asoc->sent_cnt_removable will record how many chunks can be checked to
remove. If priority policy is enabled, when the chunk is queued into
the out_queue, we will increase sent_cnt_removable. When the chunk is
moved to abandon_queue or dequeue and free, we will decrease
sent_cnt_removable.

In sctp_sendmsg, we will check if there is enough snd buffer for current
msg and if sent_cnt_removable is not 0. Then try to abandon chunks in
sctp_prune_prsctp when sendmsg from the retransmit/transmited queue, and
free chunks from out_queue in right order until the abandon+free size >
msg_len - sctp_wfree. For the abandon size, we have to wait until it
sends FORWARD TSN, receives the sack and the chunks are really freed.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

prsctp RTX policy is a policy to abandon chunks when they are
retransmitted beyond the max count.

This patch uses sent_count to count how many times one chunk has
been sent, and prsctp_param is the max rtx count, which is from
sinfo->sinfo_timetolive in sctp_set_prsctp_policy(). So similar
to TTL policy, if RTX policy is enabled, msg->expire_at won't
work.

Then in sctp_chunk_abandoned, this patch checks if chunk->sent_count
is bigger than chunk->prsctp_param to abandon this chunk.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

prsctp TTL policy is a policy to abandon chunks when they expire
at the specific time in local stack. It's similar with expires_at
in struct sctp_datamsg.

This patch uses sinfo->sinfo_timetolive to set the specific time for
TTL policy. sinfo->sinfo_timetolive is also used for msg->expires_at.
So if prsctp_enable or TTL policy is not enabled, msg->expires_at
still works as before.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds SCTP_PR_ASSOC_STATUS to sctp sockopt, which is used
to dump the prsctp statistics info from the asoc. The prsctp statistics
includes abandoned_sent/unsent from the asoc. abandoned_sent is the
count of the packets we drop packets from retransmit/transmited queue,
and abandoned_unsent is the count of the packets we drop from out_queue
according to the policy.

Note: another option for prsctp statistics dump described in rfc is
SCTP_PR_STREAM_STATUS, which is used to dump the prsctp statistics
info from each stream. But by now, linux doesn't yet have per stream
statistics info, it needs rfc6525 to be implemented. As the prsctp
statistics for each stream has to be based on per stream statistics,
we will delay it until rfc6525 is done in linux.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds SCTP_DEFAULT_PRINFO to sctp sockopt. It is used
to set/get sctp Partially Reliable Policies' default params,
which includes 3 policies (ttl, rtx, prio) and their values.

Still, if we set policy params in sndinfo, we will use the params
of sndinfo against chunks, instead of the default params.

In this patch, we will use 5-8bit of sp/asoc->default_flags
to store prsctp policies, and reuse asoc->default_timetolive
to store their values. It means if we enable and set prsctp
policy, prior ttl timeout in sctp will not work any more.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to section 4.5 of rfc7496, prsctp_enable should be per asoc.
We will add prsctp_enable to both asoc and ep, and replace the places
where it used net.sctp->prsctp_enable with asoc->prsctp_enable.

ep->prsctp_enable will be initialized with net.sctp->prsctp_enable, and
asoc->prsctp_enable will be initialized with ep->prsctp_enable. We can
also modify it's value through sockopt SCTP_PR_SUPPORTED.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 4386f566 ("net: ethernet: bcmgenet: use
phy_ethtool_{get|set}_link_ksettings")

This patch is wrong, the function phy_ethtool_{get|set}_link_ksettings
don't check if the device is running, but the driver bcmgenet need this
check.

The function {get|set}_settings need to access the mdio bus, and this
bus may only be used when the device is running. Otherwise, the clock
is disable and a mdio access will fail.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: b53: Add Broadcom NSP switch support

This patch series updates the B53 driver to support Broadcom's Northstar Plus
Soc integrated switch.

Unlike the version of the core present in BCM5301x/Northstar, we cannot read the
full chip id of the switch, so we need to get the information about our switch
id from Device Tree.

Other than that, this is a regular Broadcom Ethernet switch which is register
compatible for all practical purposes with the existing switch driver.

Since DSA requires a working CPU Ethernet MAC driver this depends on Jon
Mason's AMAC/BGMAC driver changes to support NSP. Board specific changes depend
on patches present in Broadcom's ARM SoC branches and will be posted in a short
while.
====================
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the SRAB, core driver and binding document to support the
BCM585xx/586xx/88312 integrated switch (Northstar Plus SoCs family).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For Northstart Plus SoCs, we cannot detect the switch because only the
revision information is provied in the Management page, instead, rely on
Device Tree to tell us the chip id, and pass it down using the
b53_platform_data structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for TSE PCS that uses SGMII adapter when the phy-mode of
the dwmac is set to sgmii.
Signed-off-by: Tien Hock Loh <thloh@altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

All inet6_netconf_notify_devconf() callers are in process context,
so we can use GFP_KERNEL allocations if we take care of not holding
a rwlock while not needed in ip6mr (we hold RTNL there)

Fixes: d67b8c61 ("netconf: advertise mc_forwarding status")
Fixes: f3a1bfb1 ("rtnl/ipv6: use netconf msg to advertise forwarding status")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet_forward_change() runs with RTNL held.
We are allowed to sleep if required.

If we use __in_dev_get_rtnl() instead of __in_dev_get_rcu(),
we no longer have to use GFP_ATOMIC allocations in
inet_netconf_notify_devconf(), meaning we are less likely to miss
notifications under memory pressure, and wont touch precious memory
reserves either and risk dropping incoming packets.

inet_netconf_get_devconf() can also use GFP_KERNEL allocation.

Fixes: edc9e748 ("rtnl/ipv4: use netconf msg to advertise forwarding status")
Fixes: 9e551110 ("rtnl/ipv4: add support of RTM_GETNETCONF")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jon Mason says:

====================
net: ethernet: bgmac: Add platform device support

David Miller, Please consider including patches 1-5 in net-next

Florian Fainelli, Please consider including patches 6 & 7 in
  devicetree/next

Changes in v2:
* Made device tree binding changes suggested by Sergei Shtylyov,
  Ray Jui, Rob Herring, Florian Fainelli, and Arnd Bergmann
* Removed devm_* error paths in the bgmac_platform.c suggested by
  Florian Fainelli
* Added Arnd Bergmann's Acked-by to the first 5 (there were changes
  outlined in the bullets above, but I believe them to be minor enough
  for him to not revoke his acks)

This patch series adds support for other, non-bcma iProc SoC's to the
bgmac driver.  This series only adds NSP support, but we are interested
in adding support for the Cygnus and NS2 families (with more possible
down the road).

To support non-bcma enabled SoCs, we need to add the standard device
tree "platform device" support.  Unfortunately, this driver is very
tighly coupled with the bcma bus and much unwinding is needed.  I tried
to break this up into a number of patches to make it more obvious what
was being done to add platform device support.  I was able to verify
that the bcma code still works using a 53012K board (NS SoC), and that
the platform code works using a 58625K board (NSP SoC).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The bcma portion of the driver has been split off into a bcma specific
driver.  This has been mirrored for the platform driver.  The last
references to the bcma core struct have been changed into a generic
function call.  These function calls are wrappers to either the original
bcma code or new platform functions that access the same areas via MMIO.
This necessitated adding function pointers for both platform and bcma to
hide which backend is being used from the generic bgmac code.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bgmac driver is using the bcma provides device ID and revision, as
well as the SoC ID and package, to determine which features are
necessary to enable, reset, etc in the driver.   In anticipation of
removing the bcma requirement for this driver, these must be changed to
not reference that struct.  In place of that, each "feature" has been
given a flag, and the flags are enabled for their respective device and
SoC.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the BCMA MDIO phy into a separate file, as it is very tightly
coupled with the BCMA bus.  This will help with the upcoming BCMA
removal from the bgmac driver.  Optimally, this should be moved into
phy drivers, but it is too tightly coupled with the bgmac driver to
effectively move it without more changes to the driver.

Note: the phy_reset was intentionally removed, as the mdio phy subsystem
automatically resets the phy if a reset function pointer is present.  In
addition to the moving of the driver, this reset function is added.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dma buffer allocation, etc references a dma_dev device pointer from
the bcma core.  In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct.  Add a
dma_dev device pointer to the bgmac stuct and reference that instead.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bgmac_* print wrappers call dev_* prints with the dev pointer from
the bcma core.  In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct.  So,
simply change all of the bgmac_* prints to their dev_* counterparts.  In
some cases netdev_* prints are more appropriate, so change those as
well.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An important information for the napi_poll tracepoint is knowing
the work done (packets processed) by the napi_poll() call. Add
both the work done and budget, as they are related.

Handle trace_napi_poll() param change in dropwatch/drop_monitor
and in python perf script netdev-times.py in backward compat way,
as python fortunately supports optional parameter handling.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: remove the redundant code

Remove the unnacessary code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no conflict between the work_queue function and
rtl8152_set_speed(), so we don't have to cancel the delayed work in
rtl8152_set_speed().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 90186af4 ("r8152: fix lockup when runtime PM is enabled"),
the autoresume wouldn't start the device before rtl8152_open() is finished.
Therefore, we don't have to reset the linking status before and after
autoresume. That is, one of netif_carrier_off() in rtl8152_open() could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In rtl_hw_phy_work_func_t(), the flag of PHY_RESET is set in
rtl_ops.hw_phy_cfg() and cleared in rtl8152_set_speed(). Therefore,
the rtl_phy_reset() is never run and is unnecessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
net: support MPLS in IPv4 and UDP

This short series provides support for MPLS in IPv4 (RFC4023), and by
virtue of FOU, MPLS in UDP (RFC7510).

The changes are as follows:
1. Teach tunnel4.c about AF_MPLS, it already understands AF_INET and
   AF_INET6
2. Enhance IPIP and SIT to handle MPLS. Both already handle IPv4.
   SIT also already handles IPv6.
3. Trivially enhance MPLS to allow routes over SIT and IPIP tunnels.

A corresponding patch set for iproute2 has also been provided.

Changes since v1
* Correct inverted IPIP protocol logic in SIT patch
* Provide usage example below

Sample configuration follows:

* The following creates a tunnel and routes MPLS packets whose outermost
  label is 100 over it. The forwarded packets will have the outermost label
  stack entry, 100, removed and two label stack entries added, the
  outermost having label 200 and the next having label 300.

  The local end-point for the tunnel is 10.0.99.192 and the remote
  endpoint is 10.0.99.193.

  The local address for encapsulated packets is 10.0.98.192 and the
  remote address is 10.0.98.193.

  # Create an MPLS over IPv4 tunnel using the IPIP driver
  ip link add name tun1 type ipip remote 10.0.99.193 local 10.0.99.192 \
	ttl 225 mode mplsip

  # Bring the tunnel up and an add an IPv4 address and route
  ip link set up dev tun1
  ip addr add 10.0.98.192/24 dev tun1

  # Set MPLS route
  # Allow MPLS forwarding of packets recieved on eth0
  echo 1 > /proc/sys/net/mpls/conf/eth0/input
  # Larger than label to be routed (100)
  echo 101 > /proc/sys/net/mpls/platform_labels
  ip -f mpls route add 100 as 200/300 via inet 10.0.98.193

* For FOU (in this case MPLS over UDP) a tunnel may created using:

  # Packets recieved on UDP port 6635 are MPLS over UDP (IP proto 137)
  ip fou add port 6635 ipproto 137
  # Create the tunnel netdev
  ip link add name tun1 type ipip remote 10.0.99.193 local 10.0.99.192 \
	ttl 225 mode mplsip encap fou encap-sport auto encap-dport 6635

  IPv4 address, link and route, and MPLS routing commands are as per
  the MPLS over IPv4 example

* To use the SIT driver instead of the IPIP driver "ipip" may be substituted
  for "sit" in the above examples.

* To create a tunnel that forwards and receives all supported
  inner-protocols "mplsip" may be substituted for "any" in the above
  examples.

  For the IPIP driver this configures both IPv4 and MPLS over IPv4.
  For the SIT driver this configures IPv6, IPv4 and MPLS over IPv4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow MPLS routes on IPIP and SIT devices now that they
support forwarding MPLS packets.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the IPIP driver to support MPLS over IPv4. The implementation is an
extension of existing support for IPv4 over IPv4 and is based of multiple
inner-protocol support for the SIT driver.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the SIT driver to support MPLS over IPv4. This implementation
extends existing support for IPv6 over IPv4 and IPv4 over IPv4.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend tunnel support to MPLS over IPv4.  The implementation extends the
existing differentiation between IPIP and IPv6 over IPv4 to also cover MPLS
over IPv4.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As was suggested this patch adds support for the different versions of MLD
and IGMP query types. Since the user visible structure is still in net-next
we can augment it instead of adding netlink attributes.
The distinction between the different IGMP/MLD query types is done as
suggested in Section 7.1, RFC 3376 [1] and Section 8.1, RFC 3810 [2] based
on query payload size and code for IGMP. Since all IGMP packets go through
multicast_rcv() and it uses ip_mc_check_igmp/ipv6_mc_check_mld we can be
sure that at least the ip/ipv6 header can be directly used.

[1] https://tools.ietf.org/html/rfc3376#section-7
[2] https://tools.ietf.org/html/rfc3810#section-8.1Suggested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we introduced GSO support, if using auth the auth chunk was being
left queued on the packet even after the final segment was generated.
Later on sctp_transmit_packet it calls sctp_packet_reset, which zeroed
the packet len while not accounting for this left-over. This caused more
space to be used the next packet due to the chunk still being queued,
but space which wasn't allocated as its size wasn't accounted.

The fix is to only queue it back when we know that we are going to
generate another segment.

Fixes: 90017acc ("sctp: Add GSO support")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This code generates as static checker warning because htons(ETH_P_IPV6)
is always true.  From the context it looks like the && was intended to
be !=.

Fixes: 94758f8d ('bnxt_en: Add GRO logic for BCM5731X chips.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

over time there were multiple requests to access different data
structures and fields of task_struct current, so finally add
the helper to access 'current' as-is. Tracing bpf programs will do
the rest of walking the pointers via bpf_probe_read().
Note that current can be null and bpf program has to deal it with,
but even dumb passing null into bpf_probe_read() is still safe.
Suggested-by: Brendan Gregg <brendan.d.gregg@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>