Saeed Mahameed says:

====================
This patch series contains various fixes, additions and improvements to
mlx5 software steering.

Patch 1:
  adds support for REMOVE_HEADER packet reformat - a new reformat type
  that is supported starting with ConnectX-6 DX, and allows removing an
  arbitrary size packet segment at a selected position.

Patches 2 and 3:
  add support for VLAN pop on TX and VLAN push on RX flows.

Patch 4:
  enables retransmission mechanism for the SW Steering RC QP.

Patch 5:
  does some improvements to error flow in building STE array and adds
  a more informative printout of an invalid actions sequence.

Patch 6:
  improves error flow on SW Steering QP error.

Patch 7:
  reduces the log level of a message that is printed when a table is
  connected to a lower/same level destination table, as this case proves to
  be not as rare as it was in the past.

Patch 8:
  adds missing support for matching on IPv6 flow label for devices
  older than ConnectX-6 DX.

Patch 9:
  replaces uintN_t types with kernel-style types.

Patch 10:
  allows for using the right API for updating flow tables - if it is
  a FW-owned table, then FW API will be used.

Patch 11:
  adds support for 'ignore_flow_level' on multi-destination flow
  tables that are created by SW Steering.

Patch 12:
   optimizes FDB RX steering rule by skipping matching on source port,
   as the source port for all incoming packets equals to wire.

Patch 13:
   is a small code refactoring - it merges several DR_STE_SIZE enums
   into a single enum.

Patch 14:
   does some additional refactoring and removes HW-specific STE type
   from NIC domain.

Patch 15:
   removes rehash ctrl struct from dr_htbl struct and saves some memory.

Patch 16:
   does a more significant improvement in terms of memory consumption
   and was able to save about 1.6 Gb for 8M rules.

Patch 17:
   adds support for update FTE, which is needed for cases where there
   are multiple rules with the same match.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: Optimize received options handling

These patches optimize received MPTCP option handling in terms of both
storage and fewer conditionals to evaluate in common cases, and also add
a couple of cleanup patches.

Patches 1 and 5 do some cleanup in checksum option parsing and
clarification of lock handling.

Patches 2 and 3 rearrange struct mptcp_options_received to shrink it
slightly and consolidate frequently used fields in the same cache line.

Patch 4 optimizes incoming MPTCP option parsing to skip many extra
comparisons in the common case where only a DSS option is present.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian noted the locking schema used by __mptcp_push_pending()
is hard to follow, let's add some more descriptive comments
and drop an unneeded and confusing check.
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most MPTCP packets carries a single MPTCP subption: the
DSS containing the mapping for the current packet.

Check explicitly for the above, so that is such scenario we
replace most conditional statements with a single likely() one.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes input options processing more consistent with
output ones and will simplify the next patch.

Also avoid clearing the suboption field after processing
it, since it's not needed.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change reorder the mptcp_options_received fields
to shrink the structure a bit and to ensure the most
frequently used fields are all in the first cacheline.

Sub-opt specific flags are moved out of the suboptions area,
and we must now explicitly set them when the relevant
suboption is parsed.

There is a notable exception: 'csum_reqd' is used by both DSS
and MPC suboptions, and keeping such field in the suboptions
flag area will simplfy the next patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Should be set only if the ingress packets present it, otherwise
we can confuse csum validation.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TCP_WINDOW_CLAMP socket option is defined in tcp(7) to "Bound the size
of the advertised window to this value."  Window clamping is distributed
across two variables, window_clamp ("Maximal window to advertise" in
tcp.h) and rcv_ssthresh ("Current window clamp").

This patch updates the function where the window clamp is set to also
reduce the current window clamp, rcv_sshthresh, if needed.  With this,
setting the TCP_WINDOW_CLAMP option has the documented effect of limiting
the window.
Signed-off-by: Neil Spring <ntspring@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210825210117.1668371-1-ntspring@fb.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/wwan/mhi_wwan_mbim.c - drop the extra arg.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add the support for update FTE, which is needed for cases where there are
multiple rules with the same match. In such case fs_core will merge the
actions and call update FTE to update current FTE. Since we don't want to
disrupt the traffic, we will add the new duplicate rule, and only then
remove the old duplicate rule.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

To track each STE of the rule a rule member was allocated, each
member would point to one STE. This means that we would allocate
40B (rule member) * number of STEs per rule.

To reduce this per rule allocation we use the STE tree pointers
for next_htbl and pointing STE to navigate the tree, this allows
us to keep only the pointer to the last STE of rule (always unique).
From the last rule STE we are able to traverse and rebuild all of
the STEs that construct the rule.

In our testing with 8M rules, each consisting of 7 STES, we were able
to reduce 1.6GB of memory.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The calculations to decide for the maximum allowed collision threshold
are simple and there is no reason to save them on the htbl struct.
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Instead of using the HW specific STEv0 type, it is better to use
an enum to indicate if this is an RX or TX nic domain.
This means that now we will need to convert the nic domain type
to the corresponding STE type.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Merge DR_STE_SIZE enums - no need for a separate enum for reduced STE size.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The FDB RX pipe is connected to the wire and the source port for all
incoming packets equals to wire, single uplink port per PF, this means
there is no point of matching on the source port in such case.
Once we recognize such case, we will optimize the RX steering rule.
Note that in such case we clean both source_eswitch_owner_vhca_id and
source_port.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When creating an FTE, we might need to create multi-destination flow table,
which is eventually created by FW. In such case, this FW table should
include all the FTE properties as requested by the upper layer, including
the ability to point to another flow table with level lower or equal to
the current table - indicated by the "ignore_flow_level" property.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Need to call the DR API only when it is DR table.
To update FW-owned table the driver should call the FW API.
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add missing support for matching on IPv6 flow label for STEv0.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

There are usecases with Connection Tracking that have such connection
as default, printing this warning in dmesg confuses the user.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

In the event of SW steering QP entering error state, SW steering
cannot insert more rules, and will silently ignore the insertion
after issuing a warning.
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Improve error flow and print actions sequence when an
invalid/unsupported sequence provided.
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Under high stress, SW steering might get stuck on polling for completion
that never comes.
For such cases QP needs to have protocol retransmission mechanism enabled.
Currently the retransmission timeout is defined as 0 (unlimited). Fix this
by defining a real timeout.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Enable pop VLAN action in TX and push VLAN in RX.
These actions are supported only on STEv1.

On TX: when a host sends a packet, VLAN is popped at the beginning.
On RX: just before passing the packet to the host the VLAN is pushed.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Split modify vlan state in the actions state machine to pop vlan
and push vlan states. This enables using of pop/push vlan without
restrictions (e.g. pop vlan on TX in STEv1).
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

ConnectX supports offloading of various encapsulations and decapsulations
(e.g. VXLAN), which are performed by 'Packet Reformat' action. Starting
with ConnectX-6 DX, a new reformat type is supported - REMOVE_HEADER, which
allows deleting an arbitrary size chunk at the selected position in the packet.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Pull nfsd fix from Bruce Fields:
 "This is a one-liner fix for a serious bug that can cause the server to
  become unresponsive to a client, so I think it's worth the last-minute
  inclusion for 5.14"

* tag 'nfsd-5.14-1' of git://linux-nfs.org/~bfields/linux:
  SUNRPC: Fix XPT_BUSY flag leakage in svc_handle_xprt()...

Pull networking fixes from Jakub Kicinski:
 "Networking fixes, including fixes from can and bpf.

  Closing three hw-dependent regressions. Any fixes of note are in the
  'old code' category. Nothing blocking release from our perspective.

  Current release - regressions:

   - stmmac: revert "stmmac: align RX buffers"

   - usb: asix: ax88772: move embedded PHY detection as early as
     possible

   - usb: asix: do not call phy_disconnect() for ax88178

   - Revert "net: really fix the build...", from Kalle to fix QCA6390

  Current release - new code bugs:

   - phy: mediatek: add the missing suspend/resume callbacks

  Previous releases - regressions:

   - qrtr: fix another OOB Read in qrtr_endpoint_post

   - stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings

  Previous releases - always broken:

   - inet: use siphash in exception handling

   - ip_gre: add validation for csum_start

   - bpf: fix ringbuf helper function compatibility

   - rtnetlink: return correct error on changing device netns

   - e1000e: do not try to recover the NVM checksum on Tiger Lake"

* tag 'net-5.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (43 commits)
  Revert "net: really fix the build..."
  net: hns3: fix get wrong pfc_en when query PFC configuration
  net: hns3: fix GRO configuration error after reset
  net: hns3: change the method of getting cmd index in debugfs
  net: hns3: fix duplicate node in VLAN list
  net: hns3: fix speed unknown issue in bond 4
  net: hns3: add waiting time before cmdq memory is released
  net: hns3: clear hardware resource when loading driver
  net: fix NULL pointer reference in cipso_v4_doi_free
  rtnetlink: Return correct error on changing device netns
  net: dsa: hellcreek: Adjust schedule look ahead window
  net: dsa: hellcreek: Fix incorrect setting of GCL
  cxgb4: dont touch blocked freelist bitmap after free
  ipv4: use siphash instead of Jenkins in fnhe_hashfun()
  ipv6: use siphash in rt6_exception_hash()
  can: usb: esd_usb2: esd_usb2_rx_event(): fix the interchange of the CAN RX and TX error counters
  net: usb: asix: ax88772: fix boolconv.cocci warnings
  net/sched: ets: fix crash when flipping from 'strict' to 'quantum'
  qede: Fix memset corruption
  net: stmmac: fix kernel panic due to NULL pointer dereference of buf->xdp
  ...

Pull arm64 fix from Will Deacon:
 "We received a report this week that the generic version of
  pfn_valid(), which we switched to this merge window in 16c9afc7
  ("arm64/mm: drop HAVE_ARCH_PFN_VALID"), interacts badly with
  dma_map_resource() due to the following check:

        /* Don't allow RAM to be mapped */
        if (WARN_ON_ONCE(pfn_valid(PHYS_PFN(phys_addr))))
                return DMA_MAPPING_ERROR;

  Since the ongoing saga to determine the semantics of pfn_valid() is
  unlikely to be resolved this week (does it indicate valid memory, or
  just the presence of a struct page, or whether that struct page has
  been initialised?), just revert back to our old version of pfn_valid()
  for 5.14.

  Summary:

   - Fix dma_map_resource() by reverting back to old pfn_valid() code"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  Partially revert "arm64/mm: drop HAVE_ARCH_PFN_VALID"

Pull ceph fixes from Ilya Dryomov:
 "Two memory management fixes for the filesystem"

* tag 'ceph-for-5.14-rc8' of git://github.com/ceph/ceph-client:
  ceph: fix possible null-pointer dereference in ceph_mdsmap_decode()
  ceph: correctly handle releasing an embedded cap flush

This reverts commit ce78ffa3.

Wren and Nicolas reported that ath11k was failing to initialise QCA6390
Wi-Fi 6 device with error:

qcom_mhi_qrtr: probe of mhi0_IPCR failed with error -22

Commit ce78ffa3 ("net: really fix the build..."), introduced in
v5.14-rc5, caused this regression in qrtr. Most likely all ath11k
devices are broken, but I only tested QCA6390. Let's revert the broken
commit so that ath11k works again.
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210826172816.24478-1-kvalo@codeaurora.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull btrfs fix from David Sterba:
 "One more fix that I think qualifies for a late merge. It's a revert of
  a one-liner fix that meanwhile got backported to stable kernels and we
  got reports from users.

  The broken fix prevents creating compressed inline extents, which
  could be noticeable on space consumption.

  Technically it's a regression as the patch was merged in 5.14-rc1 but
  got propagated to several stable kernels and has higher exposure than
  a 'typical' development cycle bug"

* tag 'for-5.14-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Revert "btrfs: compression: don't try to compress if we don't have enough pages"

Alexei Starovoitov says:

====================
bpf 2021-08-26

We've added 1 non-merge commit during the last 1 day(s):

1) Fix ringbuf helper function compatibility, from Daniel.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  bpf: Fix ringbuf helper function compatibility
====================

Link: https://lore.kernel.org/r/20210826153720.19083-1-alexei.starovoitov@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Guangbin Huang says:

====================
net: hns3: add some fixes for -net

This series adds some fixes for the HNS3 ethernet driver.
====================

Link: https://lore.kernel.org/r/1629976921-43438-1-git-send-email-huangguangbin2@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.

for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on

To fix this problem, just returns user's PFC config parameter saved in
driver.

Fixes: cacde272 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The GRO configuration is enabled by default after reset. This
is incorrect and should be restored to the user-configured value.
So this restoration is added during reset initialization.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, the cmd index is obtained in debugfs by comparing file names.
However, this method may cause errors when processing more complex file
names. So, change this method by saving cmd in private data and comparing
it when getting cmd index in debugfs for optimization.

Fixes: 5e69ea7e ("net: hns3: refactor the debugfs process")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

VLAN list should not be added duplicate VLAN node, otherwise it would
cause "add failed" when restore VLAN from VLAN list, so this patch adds
VLAN ID check before adding node into VLAN list.

Fixes: c6075b19 ("net: hns3: Record VF vlan tables")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In bond 4, when the link goes down and up repeatedly, the bond may get an
unknown speed, and then this port can not work.

The driver notify netif_carrier_on() before update the link state, when the
bond receive carrier on, will query the speed of the port, if the query
operation happens before updating the link state, will get an unknown
speed. So need to notify netif_carrier_on() after update the link state.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After the cmdq registers are cleared, the firmware may take time to
clear out possible left over commands in the cmdq. Driver must release
cmdq memory only after firmware has completed processing of left over
commands.

Fixes: 232d0d55 ("net: hns3: uninitialize command queue while unloading PF driver")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>