When a timer tick occurs and the clock is in one-shot mode, the timer
needs to be stopped to prevent it triggering subsequent interrupts.
Currently this code is in exynos4_mct_tick_clear(), but as it is
only needed when an ISR occurs move it into exynos4_mct_tick_isr(),
leaving exynos4_mct_tick_clear() just doing what its name suggests it
should.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

The Allwinner A64 SoC is known[1] to have an unstable architectural
timer, which manifests itself most obviously in the time jumping forward
a multiple of 95 years[2][3]. This coincides with 2^56 cycles at a
timer frequency of 24 MHz, implying that the time went slightly backward
(and this was interpreted by the kernel as it jumping forward and
wrapping around past the epoch).

Investigation revealed instability in the low bits of CNTVCT at the
point a high bit rolls over. This leads to power-of-two cycle forward
and backward jumps. (Testing shows that forward jumps are about twice as
likely as backward jumps.) Since the counter value returns to normal
after an indeterminate read, each "jump" really consists of both a
forward and backward jump from the software perspective.

Unless the kernel is trapping CNTVCT reads, a userspace program is able
to read the register in a loop faster than it changes. A test program
running on all 4 CPU cores that reported jumps larger than 100 ms was
run for 13.6 hours and reported the following:

 Count | Event
-------+---------------------------
  9940 | jumped backward      699ms
   268 | jumped backward     1398ms
     1 | jumped backward     2097ms
 16020 | jumped forward       175ms
  6443 | jumped forward       699ms
  2976 | jumped forward      1398ms
     9 | jumped forward    356516ms
     9 | jumped forward    357215ms
     4 | jumped forward    714430ms
     1 | jumped forward   3578440ms

This works out to a jump larger than 100 ms about every 5.5 seconds on
each CPU core.

The largest jump (almost an hour!) was the following sequence of reads:
    0x0000007fffffffff → 0x00000093feffffff → 0x0000008000000000

Note that the middle bits don't necessarily all read as all zeroes or
all ones during the anomalous behavior; however the low 10 bits checked
by the function in this patch have never been observed with any other
value.

Also note that smaller jumps are much more common, with backward jumps
of 2048 (2^11) cycles observed over 400 times per second on each core.
(Of course, this is partially explained by lower bits rolling over more
frequently.) Any one of these could have caused the 95 year time skip.

Similar anomalies were observed while reading CNTPCT (after patching the
kernel to allow reads from userspace). However, the CNTPCT jumps are
much less frequent, and only small jumps were observed. The same program
as before (except now reading CNTPCT) observed after 72 hours:

 Count | Event
-------+---------------------------
    17 | jumped backward      699ms
    52 | jumped forward       175ms
  2831 | jumped forward       699ms
     5 | jumped forward      1398ms

Further investigation showed that the instability in CNTPCT/CNTVCT also
affected the respective timer's TVAL register. The following values were
observed immediately after writing CNVT_TVAL to 0x10000000:

 CNTVCT             | CNTV_TVAL  | CNTV_CVAL          | CNTV_TVAL Error
--------------------+------------+--------------------+-----------------
 0x000000d4a2d8bfff | 0x10003fff | 0x000000d4b2d8bfff | +0x00004000
 0x000000d4a2d94000 | 0x0fffffff | 0x000000d4b2d97fff | -0x00004000
 0x000000d4a2d97fff | 0x10003fff | 0x000000d4b2d97fff | +0x00004000
 0x000000d4a2d9c000 | 0x0fffffff | 0x000000d4b2d9ffff | -0x00004000

The pattern of errors in CNTV_TVAL seemed to depend on exactly which
value was written to it. For example, after writing 0x10101010:

 CNTVCT             | CNTV_TVAL  | CNTV_CVAL          | CNTV_TVAL Error
--------------------+------------+--------------------+-----------------
 0x000001ac3effffff | 0x1110100f | 0x000001ac4f10100f | +0x1000000
 0x000001ac40000000 | 0x1010100f | 0x000001ac5110100f | -0x1000000
 0x000001ac58ffffff | 0x1110100f | 0x000001ac6910100f | +0x1000000
 0x000001ac66000000 | 0x1010100f | 0x000001ac7710100f | -0x1000000
 0x000001ac6affffff | 0x1110100f | 0x000001ac7b10100f | +0x1000000
 0x000001ac6e000000 | 0x1010100f | 0x000001ac7f10100f | -0x1000000

I was also twice able to reproduce the issue covered by Allwinner's
workaround[4], that writing to TVAL sometimes fails, and both CVAL and
TVAL are left with entirely bogus values. One was the following values:

 CNTVCT             | CNTV_TVAL  | CNTV_CVAL
--------------------+------------+--------------------------------------
 0x000000d4a2d6014c | 0x8fbd5721 | 0x000000d132935fff (615s in the past)
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>

========================================================================

Because the CPU can read the CNTPCT/CNTVCT registers faster than they
change, performing two reads of the register and comparing the high bits
(like other workarounds) is not a workable solution. And because the
timer can jump both forward and backward, no pair of reads can
distinguish a good value from a bad one. The only way to guarantee a
good value from consecutive reads would be to read _three_ times, and
take the middle value only if the three values are 1) each unique and
2) increasing. This takes at minimum 3 counter cycles (125 ns), or more
if an anomaly is detected.

However, since there is a distinct pattern to the bad values, we can
optimize the common case (1022/1024 of the time) to a single read by
simply ignoring values that match the error pattern. This still takes no
more than 3 cycles in the worst case, and requires much less code. As an
additional safety check, we still limit the loop iteration to the number
of max-frequency (1.2 GHz) CPU cycles in three 24 MHz counter periods.

For the TVAL registers, the simple solution is to not use them. Instead,
read or write the CVAL and calculate the TVAL value in software.

Although the manufacturer is aware of at least part of the erratum[4],
there is no official name for it. For now, use the kernel-internal name
"UNKNOWN1".

[1]: https://github.com/armbian/build/commit/a08cd6fe7ae9
[2]: https://forum.armbian.com/topic/3458-a64-datetime-clock-issue/
[3]: https://irclog.whitequark.org/linux-sunxi/2018-01-26
[4]: https://github.com/Allwinner-Homlet/H6-BSP4.9-linux/blob/master/drivers/clocksource/arm_arch_timer.c#L272Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

If the clock tree is not fully populated when the timer-sun5i init code
is called, attempts to get the clock rate for the timer would fail and
return 0.

Make the init code for both clock events and clocksource check the
returned clock rate and fail gracefully if the result is 0, instead of
causing a divide by 0 exception later on.

Fixes: 4a59058f ("clocksource/drivers/sun5i: Refactor the current code")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where fall through is indeed expected.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190123081413.GA3949@embeddedor

When calling debugfs functions, there is no need to ever check the return
value.  The function can work or not, but the code logic should never do
something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190122152151.16139-43-gregkh@linuxfoundation.org

Posix CPU timers store the interval in private storage for historical
reasons (it_interval used to be a non scalar representation on 32bit
systems). This is gone and there is no reason for duplicated storage
anymore.

Use it_interval everywhere.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "H.J. Lu" <hjl.tools@gmail.com>
Link: https://lkml.kernel.org/r/20190111133500.945255655@linutronix.de

Merge urgent fix so depending cleanup patch can be applied.

The recent commit which prevented a division by 0 issue in the alarm timer
code broke posix CPU timers as an unwanted side effect.

The reason is that the common rearm code checks for timer->it_interval
being 0 now. What went unnoticed is that the posix cpu timer setup does not
initialize timer->it_interval as it stores the interval in CPU timer
specific storage. The reason for the separate storage is historical as the
posix CPU timers always had a 64bit nanoseconds representation internally
while timer->it_interval is type ktime_t which used to be a modified
timespec representation on 32bit machines.

Instead of reverting the offending commit and fixing the alarmtimer issue
in the alarmtimer code, store the interval in timer->it_interval at CPU
timer setup time so the common code check works. This also repairs the
existing inconistency of the posix CPU timer code which kept a single shot
timer armed despite of the interval being 0.

The separate storage can be removed in mainline, but that needs to be a
separate commit as the current one has to be backported to stable kernels.

Fixes: 0e334db6 ("posix-timers: Fix division by zero bug")
Reported-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190111133500.840117406@linutronix.de

Both CONTEXT_TRACKING and CONTEXT_TRACKING_FORCE are currently defined
in kernel/rcu/kconfig, which might have made sense at some point, but
no longer does given that RCU refers to neither of these Kconfig options.

Therefore move them to kernel/time/Kconfig, where the rest of the
NO_HZ_FULL Kconfig options live.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: https://lkml.kernel.org/r/20181220170525.GA12579@linux.ibm.com

UNAME26 is a mechanism to report Linux's version as 2.6.x, for
compatibility with old/broken software.  Due to the way it is
implemented, it would have to be updated after 5.0, to keep the
resulting versions unique.  Linus Torvalds argued:

 "Do we actually need this?

  I'd rather let it bitrot, and just let it return random versions. It
  will just start again at 2.4.60, won't it?

  Anybody who uses UNAME26 for a 5.x kernel might as well think it's
  still 4.x. The user space is so old that it can't possibly care about
  differences between 4.x and 5.x, can it?

  The only thing that matters is that it shows "2.4.<largeenough>",
  which it will do regardless"
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC fixes from Olof Johansson:
 "A bigger batch than I anticipated this week, for two reasons:

   - Some fallout on Davinci from board file -> DTB conversion, that
     also includes a few longer-standing fixes (i.e. not recent
     regressions).

   - drivers/reset material that has been in linux-next for a while, but
     didn't get sent to us until now for a variety of reasons
     (maintainer out sick, holidays, etc). There's a functional
     dependency in there such that one platform (Altera's SoCFPGA) won't
     boot without one of the patches; instead of reverting the patch
     that got merged, I looked at this set and decided it was small
     enough that I'll pick it up anyway. If you disagree I can revisit
     with a smaller set.

  That being said, there's also a handful of the usual stuff:

   - Fix for a crash on Armada 7K/8K when the kernel touches
     PSCI-reserved memory

   - Fix for PCIe reset on Macchiatobin (Armada 8K development board,
     what this email is sent from in fact :)

   - Enable a few new-merged modules for Amlogic in arm64 defconfig

   - Error path fixes on Integrator

   - Build fix for Renesas and Qualcomm

   - Initialization fix for Renesas RZ/G2E

  .. plus a few more fixlets"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
  ARM: integrator: impd1: use struct_size() in devm_kzalloc()
  qcom-scm: Include <linux/err.h> header
  gpio: pl061: handle failed allocations
  ARM: dts: kirkwood: Fix polarity of GPIO fan lines
  arm64: dts: marvell: mcbin: fix PCIe reset signal
  arm64: dts: marvell: armada-ap806: reserve PSCI area
  ARM: dts: da850-lcdk: Correct the sound card name
  ARM: dts: da850-lcdk: Correct the audio codec regulators
  ARM: dts: da850-evm: Correct the sound card name
  ARM: dts: da850-evm: Correct the audio codec regulators
  ARM: davinci: omapl138-hawk: fix label names in GPIO lookup entries
  ARM: davinci: dm644x-evm: fix label names in GPIO lookup entries
  ARM: davinci: dm355-evm: fix label names in GPIO lookup entries
  ARM: davinci: da850-evm: fix label names in GPIO lookup entries
  ARM: davinci: da830-evm: fix label names in GPIO lookup entries
  arm64: defconfig: enable modules for amlogic s400 sound card
  reset: uniphier-glue: Add AHCI reset control support in glue layer
  dt-bindings: reset: uniphier: Add AHCI core reset description
  reset: uniphier-usb3: Rename to reset-uniphier-glue
  dt-bindings: reset: uniphier: Replace the expression of USB3 with generic peripherals
  ...

Pull btrfs fixes from David Sterba:

 - two regression fixes in clone/dedupe ioctls, the generic check
   callback needs to lock extents properly and wait for io to avoid
   problems with writeback and relocation

 - fix deadlock when using free space tree due to block group creation

 - a recently added check refuses a valid fileystem with seeding device,
   make that work again with a quickfix, proper solution needs more
   intrusive changes

* tag 'for-5.0-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: Use real device structure to verify dev extent
  Btrfs: fix deadlock when using free space tree due to block group creation
  Btrfs: fix race between reflink/dedupe and relocation
  Btrfs: fix race between cloning range ending at eof and writeback

Pull driver core fixes from Greg KH:
 "Here is one small sysfs change, and a documentation update for 5.0-rc2

  The sysfs change moves from using BUG_ON to WARN_ON, as discussed in
  an email thread on lkml while trying to track down another driver bug.
  sysfs should not be crashing and preventing people from seeing where
  they went wrong. Now it properly recovers and warns the developer.

  The documentation update removes the use of BUS_ATTR() as the kernel
  is moving away from this to use the specific BUS_ATTR_RW() and friends
  instead. There are pending patches in all of the different subsystems
  to remove the last users of this macro, but for now, don't advertise
  it should be used anymore to keep new ones from being introduced.

  Both have been in linux-next with no reported issues"

* tag 'driver-core-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  Documentation: driver core: remove use of BUS_ATTR
  sysfs: convert BUG_ON to WARN_ON

Pull staging driver fixes from Greg KH:
 "Here are some small staging driver fixes for some reported issues.

  One reverts a patch that was made to the rtl8723bs driver that turned
  out to not be needed at all as it was a bug in clang. The others fix
  up some reported issues in the rtl8188eu driver and update the
  MAINTAINERS file to point to Larry for this driver so he can get the
  bug reports easier.

  All have been in linux-next with no reported issues"

* tag 'staging-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert "staging: rtl8723bs: Mark ACPI table declaration as used"
  staging: rtl8188eu: Fix module loading from tasklet for WEP encryption
  staging: rtl8188eu: Fix module loading from tasklet for CCMP encryption
  MAINTAINERS: Add entry for staging driver r8188eu

Pull tty/serial fixes from Greg KH:
 "Here are 2 tty and serial fixes for 5.0-rc2 that resolve some reported
  issues.

  The first is a simple serial driver fix for a regression that showed
  up in 5.0-rc1. The second one resolves a number of reported issues
  with the recent tty locking fixes that went into 5.0-rc1. Lots of
  people have tested the second one and say it resolves their issues.

  Both have been in linux-next with no reported issues"

* tag 'tty-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Don't hold ldisc lock in tty_reopen() if ldisc present
  serial: lantiq: Do not swap register read/writes

Pull USB fixes from Greg KH:
 "Here are some small USB driver fixes and quirk updates for 5.0-rc2.

  The majority here are some quirks for some storage devices to get them
  to work properly. There's also a fix here to resolve the reported
  issues with some audio devices that say they are UAC3 compliant, but
  really are not.

  And a fix up for the MAINTAINERS file to remove a dead url.

  All have been in linux-next with no reported issues"

* tag 'usb-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: storage: Remove outdated URL from MAINTAINERS
  USB: Add USB_QUIRK_DELAY_CTRL_MSG quirk for Corsair K70 RGB
  usbcore: Select only first configuration for non-UAC3 compliant devices
  USB: storage: add quirk for SMI SM3350
  USB: storage: don't insert sane sense for SPC3+ when bad sense specified
  usb: cdc-acm: send ZLP for Telit 3G Intel based modems

Pull cifs fixes from Steve French:
 "A set of cifs/smb3 fixes, 4 for stable, most from Pavel. His patches
  fix an important set of crediting (flow control) problems, and also
  two problems in cifs_writepages, ddressing some large i/o and also
  compounding issues"

* tag '5.0-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  CIFS: Fix error paths in writeback code
  CIFS: Move credit processing to mid callbacks for SMB3
  CIFS: Fix credits calculation for cancelled requests
  cifs: Fix potential OOB access of lock element array
  cifs: Limit memory used by lock request calls to a page
  cifs: move large array from stack to heap
  CIFS: Do not hide EINTR after sending network packets
  CIFS: Fix credit computation for compounded requests
  CIFS: Do not set credits to 1 if the server didn't grant anything
  CIFS: Fix adjustment of credits for MTU requests
  cifs: Fix a tiny potential memory leak
  cifs: Fix a debug message

Late reset controller changes for v5.0

This adds missing deassert functionality to the ARC HSDK reset driver,
fixes some indentation and grammar issues in the kernel docs, adds a
helper to count the number of resets on a device for the non-DT case
as well, adds an early reset driver for SoCFPGA and simple reset driver
support for Stratix10, and generalizes the uniphier USB3 glue layer
reset to also cover AHCI.

* tag 'reset-for-5.0-rc2' of git://git.pengutronix.de/git/pza/linux:
  reset: uniphier-glue: Add AHCI reset control support in glue layer
  dt-bindings: reset: uniphier: Add AHCI core reset description
  reset: uniphier-usb3: Rename to reset-uniphier-glue
  dt-bindings: reset: uniphier: Replace the expression of USB3 with generic peripherals
  ARM: socfpga: dts: document "altr,stratix10-rst-mgr" binding
  reset: socfpga: add an early reset driver for SoCFPGA
  reset: fix null pointer dereference on dev by dev_name
  reset: Add reset_control_get_count()
  reset: Improve reset controller kernel docs
  ARC: HSDK: improve reset driver
Signed-off-by: Olof Johansson <olof@lixom.net>

mvebu fixes for 5.0

They are all device tree fixes which also worth being in stable:

 - Reserve PSCI area on Armada 7K/8K preventing the kernel accessing
   this area and crashing while doing it.

 - Use correct PCIe reset signal on MACCHIATOBin  (Armada 8040 based)

 - Fix polarity of GPIO fan line D-Link DNS NASes(kikwood based)

* tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu:
  ARM: dts: kirkwood: Fix polarity of GPIO fan lines
  arm64: dts: marvell: mcbin: fix PCIe reset signal
  arm64: dts: marvell: armada-ap806: reserve PSCI area
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'integrator-fixes-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into fixes

Fixes for the Integrator:
- Handle failed allocations in the IM/PC bus attachment.
- Use struct_size() for allocation.

* tag 'integrator-fixes-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
  ARM: integrator: impd1: use struct_size() in devm_kzalloc()
  gpio: pl061: handle failed allocations
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes

Amlogic DT fixes for v5.0-rc
- arm64: defconfig: enable modules for amlogic s400 sound card

* tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: defconfig: enable modules for amlogic s400 sound card
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'qcom-fixes-for-5.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into fixes

Qualcomm Driver Fixes for 5.0-rc1

* Add required includes into qcom_scm.h

* tag 'qcom-fixes-for-5.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  qcom-scm: Include <linux/err.h> header
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'davinci-fixes-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes

This pull request fixes some more regressions on legacy
DaVinci board support due to GPIO driver clean-up introduced
in v4.20 kernel. These are marked for stable.

Also has fixes for some long standing Audio issues on DA850
boards.

* tag 'davinci-fixes-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: dts: da850-lcdk: Correct the sound card name
  ARM: dts: da850-lcdk: Correct the audio codec regulators
  ARM: dts: da850-evm: Correct the sound card name
  ARM: dts: da850-evm: Correct the audio codec regulators
  ARM: davinci: omapl138-hawk: fix label names in GPIO lookup entries
  ARM: davinci: dm644x-evm: fix label names in GPIO lookup entries
  ARM: davinci: dm355-evm: fix label names in GPIO lookup entries
  ARM: davinci: da850-evm: fix label names in GPIO lookup entries
  ARM: davinci: da830-evm: fix label names in GPIO lookup entries
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-fixes-for-v5.0' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

Renesas ARM Based SoC Fixes for v5.0

Renesas SoCs:
* Fix build regressions caused by move of Kconfig symbols

RZ/G2E (r8a774c0) SoC:
* Correct initialization order of 3DG-{A,B} in SYSC driver

* tag 'renesas-fixes-for-v5.0' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  soc: renesas: r8a774c0-sysc: Fix initialization order of 3DG-{A,B}
  ARM: shmobile: fix build regressions
Signed-off-by: Olof Johansson <olof@lixom.net>

Commit 49e54187 ("ata: libahci_platform: comply to PHY framework") uses
the PHY_MODE_SATA, but that enum had not yet been added. This caused a
build failure for me, with today's linux.git.

Also, there is a potentially conflicting (mis-named) PHY_MODE_SATA, hiding
in the Marvell Berlin SATA PHY driver.

Fix the build by:

    1) Renaming Marvell's defined value to a more scoped name,
       in order to avoid any potential conflicts: PHY_BERLIN_MODE_SATA.

    2) Adding the missing enum, which was going to be added anyway as part
       of [1].

[1] https://lkml.kernel.org/r/20190108163124.6409-3-miquel.raynal@bootlin.com

Fixes: 49e54187 ("ata: libahci_platform: comply to PHY framework")
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Grzegorz Jaszczyk <jaz@semihalf.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull block fixes from Jens Axboe:

 - NVMe pull request from Christoph, with little fixes all over the map

 - Loop caching fix for offset/bs change (Jaegeuk Kim)

 - Block documentation tweaks (Jeff, Jon, Weiping, John)

 - null_blk zoned tweak (John)

 - ahch mvebu suspend/resume support. Should have gone into the merge
   window, but there was some confusion on which tree had it. (Miquel)

* tag 'for-linus-20190112' of git://git.kernel.dk/linux-block: (22 commits)
  ata: ahci: mvebu: request PHY suspend/resume for Armada 3700
  ata: ahci: mvebu: add Armada 3700 initialization needed for S2RAM
  ata: ahci: mvebu: do Armada 38x configuration only on relevant SoCs
  ata: ahci: mvebu: remove stale comment
  ata: libahci_platform: comply to PHY framework
  loop: drop caches if offset or block_size are changed
  block: fix kerneldoc comment for blk_attempt_plug_merge()
  nvme: don't initlialize ctrl->cntlid twice
  nvme: introduce NVME_QUIRK_IGNORE_DEV_SUBNQN
  nvme: pad fake subsys NQN vid and ssvid with zeros
  nvme-multipath: zero out ANA log buffer
  nvme-fabrics: unset write/poll queues for discovery controllers
  nvme-tcp: don't ask if controller is fabrics
  nvme-tcp: remove dead code
  nvme-pci: fix out of bounds access in nvme_cqe_pending
  nvme-pci: rerun irq setup on IO queue init errors
  nvme-pci: use the same attributes when freeing host_mem_desc_bufs.
  nvme-pci: fix the wrong setting of nr_maps
  block: doc: add slice_idle_us to bfq documentation
  block: clarify documentation for blk_{start|finish}_plug
  ...

Pull dma_zalloc_coherent() removal from Christoph Hellwig:
 "We've always had a weird situation around dma_zalloc_coherent. To
  safely support mapping the allocations to userspace major
  architectures like x86 and arm have always zeroed allocations from
  dma_alloc_coherent, but a couple other architectures were missing that
  zeroing either always or in corner cases.

  Then later we grew anothe dma_zalloc_coherent interface to explicitly
  request zeroing, but that just added __GFP_ZERO to the allocation
  flags, which for some allocators that didn't end up using the page
  allocator ended up being a no-op and still not zeroing the
  allocations.

  So for this merge window I fixed up all remaining architectures to
  zero the memory in dma_alloc_coherent, and made dma_zalloc_coherent a
  no-op wrapper around dma_alloc_coherent, which fixes all of the above
  issues.

  dma_zalloc_coherent is now pointless and can go away, and Luis helped
  me writing a cocchinelle script and patch series to kill it, which I
  think we should apply now just after -rc1 to finally settle these
  issue"

* tag 'remove-dma_zalloc_coherent-5.0' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: remove dma_zalloc_coherent()
  cross-tree: phase out dma_zalloc_coherent() on headers
  cross-tree: phase out dma_zalloc_coherent()

Pull KVM fixes from Radim Krčmář:
 "Minor fixes for new code, corner cases, and documentation"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  x86/kvm/nVMX: don't skip emulated instruction twice when vmptr address is not backed
  Documentation/virtual/kvm: Update URL for AMD SEV API specification
  KVM/VMX: Avoid return error when flush tlb successfully in the hv_remote_flush_tlb_with_range()
  kvm: sev: Fail KVM_SEV_INIT if already initialized
  KVM: validate userspace input in kvm_clear_dirty_log_protect()
  KVM: x86: Fix bit shifting in update_intel_pt_cfg

Pull more drm fixes from Daniel Vetter:
 "Dave sends out his pull, everybody remembers holidays are over :-)

  Since Dave's already in weekend mode and it was quite a few patches I
  figured better to apply all the pulls and forward them to you. Hence
  here 2nd part of bugfixes for -rc2.

  nouveau:
   - backlight fix
   - falcon register access fix
   - fan fix.

  i915:
   - Disable PSR for Apple panels
   - Broxton ERR_PTR error state fix
   - Kabylake VECS workaround fix
   - Unwind failure on pinning the gen7 ppgtt
   - GVT workload request allocation fix

  core:
   - Fix fb-helper to work correctly with SDL 1.2 bugs
   - Fix lockdep warning in the atomic ioctl and setproperty"

* tag 'drm-fixes-2019-01-11-1' of git://anongit.freedesktop.org/drm/drm:
  drm/nouveau/falcon: avoid touching registers if engine is off
  drm/nouveau: Don't disable polling in fallback mode
  drm/nouveau: register backlight on pascal and newer
  drm: Fix documentation generation for DP_DPCD_QUIRK_NO_PSR
  drm/i915: init per-engine WAs for all engines
  drm/i915: Unwind failure on pinning the gen7 ppgtt
  drm/i915: Skip the ERR_PTR error state
  drm/i915: Disable PSR in Apple panels
  gpu/drm: Fix lock held when returning to user space.
  drm/fb-helper: Ignore the value of fb_var_screeninfo.pixclock
  drm/fb-helper: Partially bring back workaround for bugs of SDL 1.2
  drm/i915/gvt: Fix workload request allocation before request add

A feature has been added in the libahci driver: the possibility to set
a new flag in hpriv->flags to let the core handle PHY suspend/resume
automatically. Make use of this feature to make suspend to RAM work
with SATA drives on A3700.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

A3700 comphy initialization is done in the firmware (TF-A). Looking at
the SATA PHY initialization routine, there is a comment about "vendor
specific" registers. Two registers are mentioned. They are not
initialized there in the firmware because they are AHCI related, while
the firmware at this location does only PHY configuration. The
solution to avoid doing such initialization is relying on U-Boot.

While this work at boot time, U-Boot is definitely not going to run
during a resume after suspending to RAM.

Two possible solutions were considered:
* Fixing the firmware.
* Fixing the kernel driver.

The first solution would take ages to propagate, while the second
solution is easy to implement as the driver as been a little bit
reworked to prepare for such platform configuration. Hence, this patch
adds an Armada 3700 configuration function to set these two registers
both at boot time (in the probe) and after a suspend (in the resume
path).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

At the beginning, only Armada 38x SoCs where supported by the
ahci_mvebu.c driver. Commit 15d3ce7b ("ata: ahci_mvebu: add
support for Armada 3700 variant") introduced Armada 3700 support. As
opposed to Armada 38x SoCs, the 3700 variants do not have to configure
mbus and the regret option. This patch took care of avoiding such
configuration when not needed in the probe function, but failed to do
the same in the resume path. While doing so looks harmless by
experience, let's clean the driver logic and avoid doing this useless
configuration with Armada 3700 SoCs.

Because the logic is very similar between these two places, it has
been decided to factorize this code and put it in a "Armada 38x
configuration function". This function is part of a new
(per-compatible) platform data structure, so that the addition of such
configuration function for Armada 3700 will be eased.

Fixes: 15d3ce7b ("ata: ahci_mvebu: add support for Armada 3700 variant")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

For Armada-38x (32-bit) SoCs, PM platform support has been added since:
commit 32f9494c ("ARM: mvebu: prepare pm-board.c for the
                      introduction of Armada 38x support")
commit 3cbd6a6c ("ARM: mvebu: Add standby support")

For Armada 64-bit SoCs, like the A3700 also using this AHCI driver, PM
platform support has always existed.

There are even suspend/resume hooks in this driver since:
commit d6ecf158 ("ata: ahci_mvebu: add suspend/resume support")

Remove the stale comment at the end of this driver stating that all
the above does not exist yet.

Fixes: d6ecf158 ("ata: ahci_mvebu: add suspend/resume support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Current implementation of the libahci does not take into account the
new PHY framework. Correct the situation by adding a call to
phy_set_mode() before phy_power_on().

PHYs should also be handled at suspend/resume time. For this, call
ahci_platform_enable/disable_phys() at suspend/resume_host() time. These
calls are guarded by a HFLAG (AHCI_HFLAG_SUSPEND_PHYS) that the user of
the libahci driver must set manually in hpriv->flags at probe time. This
is to avoid breaking users that have not been tested with this change.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull i2c fixes from Wolfram Sang:
 "I2C has one core and one driver bugfix for you"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: tegra: Fix Maximum transfer size
  i2c: dev: prevent adapter retries and timeout being set as minus value

Pull arm64 fixes from Will Deacon:
 "Another handful of arm64 fixes here. Most of the complication comes
  from improving our kpti code to avoid lengthy pauses (30+ seconds)
  during boot when we rewrite the page tables. There are also a couple
  of IORT fixes that came in via Lorenzo.

  Summary:

   - Don't error in kexec_file_load if kaslr-seed is missing in
     device-tree

   - Fix incorrect argument type passed to iort_match_node_callback()

   - Fix IORT build failure when CONFIG_IOMMU_API=n

   - Fix kpti performance regression with new rodata default option

   - Typo fix"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: kexec_file: return successfully even if kaslr-seed doesn't exist
  ACPI/IORT: Fix rc_dma_get_range()
  arm64: kpti: Avoid rewriting early page tables when KASLR is enabled
  arm64: asm-prototypes: Fix fat-fingered typo in comment
  ACPI/IORT: Fix build when CONFIG_IOMMU_API=n

Pull ceph updates from Ilya Dryomov:
 "A patch to allow setting abort_on_full and a fix for an old "rbd
  unmap" edge case, marked for stable"

* tag 'ceph-for-5.0-rc2' of git://github.com/ceph/ceph-client:
  rbd: don't return 0 on unmap if RBD_DEV_FLAG_REMOVING is set
  ceph: use vmf_error() in ceph_filemap_fault()
  libceph: allow setting abort_on_full for rbd

Pull perf tooling updates from Ingo Molnar:
 "Tooling changes only: fixes and a few stray improvements.

  Most of the diffstat is dominated by a PowerPC related fix of system
  call trace output beautification that allows us to (again) use the
  UAPI header version and sync up with the kernel's version of PowerPC
  system call names in the arch/powerpc/kernel/syscalls/syscall.tbl
  header"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
  tools headers powerpc: Remove unistd.h
  perf powerpc: Rework syscall table generation
  perf symbols: Add 'arch_cpu_idle' to the list of kernel idle symbols
  tools include uapi: Sync linux/if_link.h copy with the kernel sources
  tools include uapi: Sync linux/vhost.h with the kernel sources
  tools include uapi: Sync linux/fs.h copy with the kernel sources
  perf beauty: Switch from using uapi/linux/fs.h to uapi/linux/mount.h
  tools include uapi: Grab a copy of linux/mount.h
  perf top: Lift restriction on using callchains without "sym" in --sort
  tools lib traceevent: Remove tep_data_event_from_type() API
  tools lib traceevent: Rename tep_is_file_bigendian() to tep_file_bigendian()
  tools lib traceevent: Changed return logic of tep_register_event_handler() API
  tools lib traceevent: Changed return logic of trace_seq_printf() and trace_seq_vprintf() APIs
  tools lib traceevent: Rename struct cmdline to struct tep_cmdline
  tools lib traceevent: Initialize host_bigendian at tep_handle allocation
  tools lib traceevent: Introduce new libtracevent API: tep_override_comm()
  perf tests: Add a test for the ARM 32-bit [vectors] page
  perf tools: Make find_vdso_map() more modular
  perf trace: Fix alignment for [continued] lines
  perf trace: Fix ')' placement in "interrupted" syscall lines
  ...

Since commit 09abb5e3 ("KVM: nVMX: call kvm_skip_emulated_instruction
in nested_vmx_{fail,succeed}") nested_vmx_failValid() results in
kvm_skip_emulated_instruction() so doing it again in handle_vmptrld() when
vmptr address is not backed is wrong, we end up advancing RIP twice.

Fixes: fca91f6d ("kvm: nVMX: Set VM instruction error for VMPTRLD of unbacked page")
Reported-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>