- 07 Sep, 2020 17 commits
-
-
Maxime Ripard authored
The VIDEN bit in the pixelvalve currently being used to enable or disable the pixelvalve seems to not be enough in some situations, which whill end up with the pixelvalve stalling. In such a case, even re-enabling VIDEN doesn't bring it back and we need to clear the FIFO. This can only be done if the pixelvalve is disabled though. In order to overcome this, we can configure the pixelvalve during mode_set_no_fb by calling vc4_crtc_config_pv, but only enable it in atomic_enable and flush the FIFO there, and in atomic_disable disable the pixelvalve again. Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Tested-by:
Chanwoo Choi <cw00.choi@samsung.com> Tested-by:
Hoegeun Kwon <hoegeun.kwon@samsung.com> Tested-by:
Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by:
Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://patchwork.freedesktop.org/patch/msgid/e97596f62f4df83424d994a23465463ac60f986e.1599120059.git-series.maxime@cerno.tech
-
Maxime Ripard authored
The vc4_crtc_handle_page_flip already has a local variable holding the value of vc4_crtc->channel, so let's use it instead. Signed-off-by:
-
Maxime Ripard authored
In vc5, the HVS has 6 outputs and 3 FIFOs (or channels), with pixelvalves each being assigned to a given output, but each output can then be muxed to feed from multiple FIFOs. Since vc4 had that entirely static, both were probably equivalent, but since that changes, let's rename hvs_channel to hvs_output in the vc4_crtc_data, since a pixelvalve is really connected to an output, and not to a FIFO. Signed-off-by:
-
Maxime Ripard authored
The COB allocation depends on the HVS channel used for a given pixelvalve. While the channel allocation was entirely static in vc4, vc5 changes that and at bind time, a pixelvalve can be assigned to multiple HVS channels. Let's prepare that rework by allocating the COB when it's actually needed. Signed-off-by:
Eric Anholt <eric@anholt.net> Link: https://patchwork.freedesktop.org/patch/msgid/484cbd4b00cfeee425295df438222258cc39a3dd.1599120059.git-series.maxime@cerno.tech
-
Maxime Ripard authored
Some pixelvalves in vc5 use the same interrupt line so let's register our interrupt handler as a shared one. Signed-off-by:
-
Maxime Ripard authored
Some of the HDMI pixelvalves in vc5 output two pixels per clock cycle. Let's put the number of pixel output per clock cycle in the CRTC data and update the various calculations to reflect that. Signed-off-by:
-
Maxime Ripard authored
Let's now create more planes that can be affected to all the CRTCs. vc4 has 3 CRTCs, 1 primary and 1 cursor each, and was having 24 (8 planes per CRTC) overlays. However, vc5 has 5 CRTCs, so keeping the same logic would put us at 50 planes which is well above the 32 planes limit imposed by DRM. Using 16 seems like a good tradeoff between staying under 32 and yet providing enough planes. Signed-off-by:
-
Dave Stevenson authored
The current code is using the maximum of the source line size and the destination line size to compute the size of the LBM to allocate. While this is simpler, it starts to be an issue with modes such as 4k with a quite long that will consume all the available memory, so we no longer have that luxury. Signed-off-by:
-
Dave Stevenson authored
The HVS5 needs an alignment of 64bytes for its LBM memory, so let's reflect it. Signed-off-by:
-
Maxime Ripard authored
In order to prevent timeouts and stalls in the pipeline, the core clock needs to be maxed at 500MHz during a modeset on the BCM2711. Signed-off-by:
-
Dave Stevenson authored
The HVS found in the BCM2711 is slightly different from the previous generations. Most notably, the display list layout changes a bit, the LBM doesn't have the same size and the formats ordering for some formats is swapped. Signed-off-by:
-
Maxime Ripard authored
The HVS found in the BCM2711 is slightly different from the previous generations, let's add a compatible for it. Signed-off-by:
-
Angelo Ribeiro authored
Add support for the video pattern generator (VPG) BER pattern mode and configuration in runtime. This enables using the debugfs interface to manipulate the VPG after the pipeline is set. Also, enables the usage of the VPG BER pattern. Changes in v2: - Added VID_MODE_VPG_MODE - Solved incompatible return type on __get and __set Reported-by:
kbuild test robot <lkp@intel.com> Reported-by:
Adrian Pop <pop.adrian61@gmail.com> Signed-off-by:
Angelo Ribeiro <angelo.ribeiro@synopsys.com> Tested-by:
Yannick Fertre <yannick.fertre@st.com> Tested-by:
Neil Armstrong <narmstrong@baylibre.com> Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Jose Abreu <jose.abreu@synopsys.com> Signed-off-by:
-
Antonio Borneo authored
Current code enables the HS clock when video mode is started or to send out a HS command, and disables the HS clock to send out a LP command. This is not what DSI spec specify. Enable HS clock either in command and in video mode. Set automatic HS clock management for panels and devices that support non-continuous HS clock. Signed-off-by:
Antonio Borneo <antonio.borneo@st.com> Tested-by:
Philippe Cornu <philippe.cornu@st.com> Reviewed-by:
-
Antonio Borneo authored
Current code does not properly computes the max length of LP commands that can be send during H or V sync, and rely on static values. Limiting the max LP length to 4 byte during the V-sync is overly conservative. Relax the limit and allows longer LP commands (16 bytes) to be sent during V-sync. Signed-off-by:
-
Antonio Borneo authored
Current code only sends LP commands in command mode. Allows sending LP commands also in video mode by setting the proper flag in DSI_VID_MODE_CFG. Signed-off-by:
-
Kristian H. Kristensen authored
Make sure we can use this on mixed systems. Signed-off-by:
Kristian H. Kristensen <hoegsberg@google.com> Link: http://patchwork.freedesktop.org/patch/msgid/20200903181652.432067-1-hoegsberg@google.comSigned-off-by:
Gerd Hoffmann <kraxel@redhat.com>
-
- 06 Sep, 2020 1 commit
-
-
Linus Walleij authored
Ooops the panel drivers stopped to use DRM_DEV* messages and we predictably create errors by merging code that still use it. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Acked-by:
Sam Ravnborg <sam@ravnborg.org> Acked-by:
David Airlie <airlied@linux.ie> Link: https://patchwork.freedesktop.org/patch/msgid/20200906132903.5739-1-linus.walleij@linaro.org
-
- 04 Sep, 2020 5 commits
-
-
Linus Walleij authored
The upstream S6E63M0 driver has some peculiarities around the prepare/enable disable/unprepare sequence: the screen is taken out of sleep in prepare() as part of s6e63m0_init() the put to on with MIPI_DCS_SET_DISPLAY_ON in enable(). However it is just put into sleep mode directly in disable(). As disable()/enable() can be called without unprepare()/prepare() being called, this is unbalanced, we should take the display out of sleep in enable() then turn it off(). Further MIPI_DCS_SET_DISPLAY_OFF is never called balanced with MIPI_DCS_SET_DISPLAY_ON. The vendor driver for Samsung GT-I8190 (Golden) does all of these things in strict order. Augment the driver to do exit sleep/set display on in enable() and set display off/enter sleep in disable(). Further send an explicit reset pulse in power_on() so we come up in a known state, and issue the MCS_ERROR_CHECK command after setting display on like the vendor driver does. Also use the timings from the vendor driver in the sequence. Doing all of these things makes the display much more stable on the Samsung GT-I8190 when enabling/disabling the display pipeline. Signed-off-by:
-
Linus Walleij authored
We add code to identify a few different panels mounted on the s6e63m0 controller. This is necessary to achieve the proper biasing with DSI versions of the panel. Signed-off-by:
Stephan Gerhold <stephan@gerhold.net> Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Acked-by:
Paul Cercueil <paul@crapouillou.net> Link: https://patchwork.freedesktop.org/patch/msgid/20200809215104.1830206-5-linus.walleij@linaro.org
-
Linus Walleij authored
This adds code to send read commands to read a single byte from the display, in order to perform MTP ID look-up of the mounted panel on the s6e63m0 controller. This is needed for proper biasing on the DSI variants. Signed-off-by:
-
Linus Walleij authored
This makes it possible to use the s6e63m0 panel with a DSI host, such as in the Samsung GT-I8190 (Golden) mobile phone. Signed-off-by:
-
Linus Walleij authored
This panel can be accessed using both SPI and DSI. To make it possible to probe and use the device also from a DSI bus, first break out the SPI support to its own file. Since all the panel driver does is write DCS commands to the panel, we pass a DCS write function to probe() from each subdriver. We make the Kconfig entry for SPI mode default so all current users will continue to work. Signed-off-by:
-
- 03 Sep, 2020 4 commits
-
-
Daniel Vetter authored
Following functions are only used internally, not by drivers: - devm_drm_dev_init Also, now that we have a very slick and polished way to allocate a drm_device with devm_drm_dev_alloc, update all the docs to reflect the new reality. Mostly this consists of deleting old and misleading hints. Two main ones: - it is no longer required that the drm_device base class is first in the structure. devm_drm_dev_alloc can cope with it being anywhere - obviously embedded now strongly recommends using devm_drm_dev_alloc v2: Fix typos (Noralf) v3: Split out the removal of drm_dev_init, that's blocked on some discussions on how to convert vgem/vkms/i915-selftests. Adjust commit message to reflect that. Cc: Noralf Trønnes <noralf@tronnes.org> Acked-by: Noralf Trønnes <noralf@tronnes.org> (v2) Acked-by:
Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200902072627.3617301-1-daniel.vetter@ffwll.ch
-
Christian König authored
That is not used any more. v2: keep the NULL checks in TTM. v3: remove unused variable Signed-off-by:
Christian König <christian.koenig@amd.com> Acked-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by:
Ben Skeggs <bskeggs@redhat.com> Link: https://patchwork.freedesktop.org/patch/388646/
-
Christian König authored
While working on TTM cleanups I've found that the io_reserve_lru used by Nouveau is actually not working at all. In general we should remove driver specific handling from the memory management, so this patch moves the io_reserve_lru handling into Nouveau instead. v2: don't call ttm_bo_unmap_virtual in nouveau_ttm_io_mem_reserve v3: rebased and use both base and offset in the check v4: fix small typos and test the patch v5: rebased and keep the mem.bus init in TTM. Signed-off-by:
-
Christian König authored
We are trying to remove the io_lru handling and depend on zero init base, offset and addr here. v2: init addr as well Signed-off-by:
-
- 02 Sep, 2020 4 commits
-
-
Randy Dunlap authored
Fix kernel-doc warning in <linux/dma-buf.h>: ../include/linux/dma-buf.h:330: warning: Function parameter or member 'name_lock' not described in 'dma_buf' Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Christian König <christian.koenig@amd.com> Cc: linux-media@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Reviewed-by:
-
Randy Dunlap authored
Add @cookie to dma_fence_end_signalling() to prevent kernel-doc warning in drivers/dma-buf/dma-fence.c: ../drivers/dma-buf/dma-fence.c:291: warning: Function parameter or member 'cookie' not described in 'dma_fence_end_signalling' Signed-off-by:
-
Gerd Hoffmann authored
Not needed, already tracked by drm_crtc_state->active. Signed-off-by:
-
Gerd Hoffmann authored
When going through a disable/enable cycle without changing the framebuffer the optimization added by commit 3954ff10 ("drm/virtio: skip set_scanout if framebuffer didn't change") causes the screen stay blank. Add a bool to force an update to fix that. v2: use drm_atomic_crtc_needs_modeset() (Daniel). Cc: 1882851@bugs.launchpad.net Fixes: 3954ff10 ("drm/virtio: skip set_scanout if framebuffer didn't change") Signed-off-by:
Jiri Slaby <jirislaby@kernel.org> Tested-by:
Diego Viola <diego.viola@gmail.com> Acked-by:
-
- 01 Sep, 2020 5 commits
-
-
Rikard Falkeborn authored
The only usage of these is to assign their address to the fbops field in the fb_info struct, which is a const pointer. Make them const to allow the compiler to put them in read-only memory. Signed-off-by:
Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by:
-
Ville Syrjälä authored
In order to shrink drm_display_mode below the magic two cacheline mark in 64bit we need to shrink it by another 8 bytes. The easiest thing to eliminate is the 'export_head' list head which is only used during the getconnector ioctl to temporarly track which modes on the connector's mode list are to be exposed and which are to remain hidden. We can simply replace the list head with a boolean which we use to tag the modes that are to be exposed. If we make sure to clear the tags after we're done with them we don't even need an extra loop over the modes to reset the tags at the start of the getconnector ioctl. Conveniently we already have a hole for the boolean left behind by the removal of mode->private_flags. The final size of the struct is now 112 bytes on 32bit and 120 bytes on 64bit. Another alternative would be a temp bitmask so we wouldn't have to have anything in the mode struct itself. The main issue is how large of a bitmask do we need? I guess we could allocate it dynamically but that means an extra kcalloc() and an extra loop through the modes to count them first (or grow the bitmask with krealloc() as needed). CC: Sam Ravnborg <sam@ravnborg.org> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Emil Velikov <emil.l.velikov@gmail.com> Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200428171940.19552-17-ville.syrjala@linux.intel.comReviewed-by:
Emil Velikov <emil.velikov@collabora.com>
-
Ville Syrjälä authored
The last two uses of mode->private_flags (in i915 and gma500) are now gone. So let's remove mode->private_flags entirely. v2: Drop the earlier int->u8 conversion CC: Sam Ravnborg <sam@ravnborg.org> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Emil Velikov <emil.l.velikov@gmail.com> Reviewed-by:
-
Sam McNally authored
For DP MST outputs, the i2c device currently only supports transfers that can be implemented using remote i2c reads. Such transfers must consist of zero or more write transactions followed by one read transaction. DDC/CI commands require standalone write transactions and hence aren't supported. Since each remote i2c write is handled as a separate transfer, remote i2c writes can support transfers consisting of write transactions, where all but the last have I2C_M_STOP set. According to the DDC/CI 1.1 standard, DDC/CI commands only require a single write or read transaction in a transfer, so this is sufficient. For i2c transfers meeting the above criteria, generate and send a remote i2c write message for each transaction. Add the trivial remote i2c write reply parsing support so remote i2c write acks bubble up correctly. Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/37Signed-off-by:
Sam McNally <sammc@chromium.org> Signed-off-by:
-
Dinghao Liu authored
When verify_crc_source() fails, source needs to be freed. However, current code is returning directly and ends up leaking memory. Fixes: d5cc15a0 ("drm: crc: Introduce verify_crc_source callback") Signed-off-by:
Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> [danvet: change Fixes: tag per Laurent's review] Signed-off-by:
-
- 31 Aug, 2020 4 commits
-
-
Randy Dunlap authored
Fix kconfig dependency warning by using a different Kconfig symbol. WARNING: unmet direct dependencies detected for VIRTIO_DMA_SHARED_BUFFER Depends on [n]: VIRTIO_MENU [=n] && DMA_SHARED_BUFFER [=y] Selected by [y]: - DRM_VIRTIO_GPU [=y] && HAS_IOMEM [=y] && DRM [=y] && VIRTIO [=y] && MMU [=y] Signed-off-by:
-
Dave Airlie authored
This can be gotten back from bdev. Reviewed-by:
Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200826014428.828392-3-airlied@gmail.com
-
Dave Airlie authored
Reviewed-by:
-
Tian Tao authored
hibmc can only be used in ARM64 architectures, and mmu defaults to y in arch/arm64/Kconfig, so there is no need to add a dependency on mmu in hibmc's kconfig. Signed-off-by:
Tian Tao <tiantao6@hisilicon.com> Reviewed-by:
Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/1598428528-49046-1-git-send-email-tiantao6@hisilicon.com
-
