Once the E822 device has sent and received one packet, the hardware
computes the internal delay of the PHY using a process known as Vernier
calibration. This calibration calculates a more accurate offset for the
Tx and Rx timestamps. To make use of this offset, we need to exit the
bypass mode. This cannot be done until the PHY has completed offset
calibration, as indicated by the offset valid bits.

To handle this, introduce a kthread work item which will poll the offset
valid bits every few milliseconds seeing if it is safe to exit bypass
mode.

Once we have finished calibrating the offsets, we can program the total
Tx and Rx offset registers and turn off the bypass bit. This allows the
hardware to include the more precise vernier calibration offset, and
improves the timestamp precision.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The E822 device has a Clock Generation Unit (CGU) responsible for
determining the clock frequency that drives the timers.

Ensure this function is initialized when bringing up the PTP support, so
that the clock has a known frequency.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Implement support for the basic operations needed to enable the PTP
hardware clock on E822 devices.

This includes implementations for the various PHY access functions, as
well as the ability to start and stop the PHY timers. This is different
from the E810 device because the configuration depends on link speed, so
we cannot just start the PHYs immediately. We must wait until the link
is up to get proper values for the speed based initialization.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Convert the clk_freq value into the associated time_ref frequency value
for E822 devices. This simplifies determining the time reference value
for the clock.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

When we enable support for E822 devices, there are some additional
steps required to initialize the PTP hardware clock. To make this easier
to implement as device-specific behavior, refactor the register setups
in ice_ptp_init_owner to a new ice_ptp_init_phc function defined in
ice_ptp_hw.c

This function will have a common section, and an e810 specific
sub-implementation.

This will enable easily extending the functionality to cover the E822
specific setup required to initialize the hardware clock generation
unit. It also makes it clear which steps are E810 specific vs which ones
are necessary for all ice devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The ice_ptp_hw.c file introduced a bunch of uses of "int status" instead
of the more traditional "int err" or "int ret". These are actually
traditional Linux error codes (as opposed to the recently removed
ice_status enumeration values).

We're about to add a bunch of new functions to ice_ptp_hw.c. It's
normally preferred in the ice driver to use "int ret" or "int err" when
dealing with error code values.

Instead of making the new functions use "int status" lets just fix all
of ice_ptp_hw.c to use "int err". This will match the new functions and
ensures a consistent style across at least the PTP related files.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The tstamp_config structure is being set inside of
ice_ptp_cfg_timestamp, which is the function used to set Tx and
Rx timestamping during initialization.

This function is also used in order to set the PHY port timestamping
status. However, it makes sense to always set the tstamp_config directly
whenever the ice_set_tx_tstamp or ice_set_rx_tstamp functions are
called.

Move assignment of tstamp_config into the related functions and out of
ice_ptp_cfg_timestamp.

Now that we assign the timestamp mode in the relevant functions, we no
longer modify the config value in ice_set_timestamp_mode. In turn, we
no longer want to copy that config value into the PF cached structure.
Instead, this is now the source of truth for actual configuration. On
success of ice_set_timestamp_mode, copy the real configured mode back to
report it out to userspace.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

A future change will add additional possible increment values for the
E822 device support. To handle this, we want to look up the increment
value to use instead of hard coding it to the nominal value for E810
devices. Introduce ice_base_incval as a function to get the best nominal
increment value to use.

For now, it just returns the E810 value, but will be refactored in the
future to look up the value based on the device type and configured
clock frequency.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The PF reset does not reset PHC and PHY clocks so it's unnecessary to
stop them and reinitialize after the reset.
Configuring timestamping changes the VSI fields so it needs to be
performed after VSIs are initialized, which was not done in case of a
reset.
Suggested-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pasi Vaananen <pvaanane@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Merge tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
This time we have:
 * ndo_fill_forward_path support in mac80211, to let drivers use it
 * association comeback notification for userspace, to be able
   to react more sensibly to long delays
 * support for background radar detection hardware in some chipsets
 * SA Query Procedures offload on the AP side
 * more logging if we find problems with HT/VHT/HE
 * various cleanups and minor fixes

Conflicts:

net/wireless/reg.c:
  e08ebd6d ("cfg80211: Acquire wiphy mutex on regulatory work")
  701fdfe3 ("cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface")
  https://lore.kernel.org/r/20211221111950.57ecc6a7@canb.auug.org.au

drivers/net/wireless/ath/ath10k/wmi.c:
  7f599aec ("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel")
  3bf2537e ("ath10k: drop beacon and probe response which leak from other channel")
  https://lore.kernel.org/r/20211221115004.1cd6b262@canb.auug.org.au

* tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (32 commits)
  cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface
  rfkill: allow to get the software rfkill state
  cfg80211: refactor cfg80211_get_ies_channel_number()
  nl82011: clarify interface combinations wrt. channels
  nl80211: Add support to offload SA Query procedures for AP SME device
  nl80211: Add support to set AP settings flags with single attribute
  mac80211: add more HT/VHT/HE state logging
  cfg80211: Use the HE operation IE to determine a 6GHz BSS channel
  cfg80211: rename offchannel_chain structs to background_chain to avoid confusion with ETSI standard
  mac80211: Notify cfg80211 about association comeback
  cfg80211: Add support for notifying association comeback
  mac80211: introduce channel switch disconnect function
  cfg80211: Fix order of enum nl80211_band_iftype_attr documentation
  cfg80211: simplify cfg80211_chandef_valid()
  mac80211: Remove a couple of obsolete TODO
  mac80211: fix FEC flag in radio tap header
  mac80211: use coarse boottime for airtime fairness code
  ieee80211: change HE nominal packet padding value defines
  cfg80211: use ieee80211_bss_get_elem() instead of _get_ie()
  mac80211: Use memset_after() to clear tx status
  ...
====================

Link: https://lore.kernel.org/r/20211221112532.28708-1-johannes@sipsolutions.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix following coccicheck warnings:
./net/sched/cls_api.c:3333:17-18: WARNING opportunity for min()
./net/sched/cls_api.c:3389:17-18: WARNING opportunity for min()
./net/sched/cls_api.c:3427:17-18: WARNING opportunity for min()
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Raju Rangoju says:

====================
net: amd-xgbe: Add support for Yellow Carp Ethernet device

Add support for newer version of Hardware, the Yellow Carp Ethernet device
====================

Link: https://lore.kernel.org/r/20211220135428.1123575-1-rrangoju@amd.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Yellow Carp Ethernet devices do not require
Autonegotiation CDR workaround, hence disable the same.
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Newer generation Hardware uses the slightly different
port speed bit widths, so alter the existing port speed
bit range to extend support to the newer generation hardware
while maintaining the backward compatibility with older
generation hardware.

The previously reserved bits are now being used which
then requires the adjustment to the BIT values, e.g.:

Before:
   PORT_PROPERTY_0[22:21] - Reserved
   PORT_PROPERTY_0[26:23] - Supported Speeds

After:
   PORT_PROPERTY_0[21] - Reserved
   PORT_PROPERTY_0[26:22] - Supported Speeds

To make this backwards compatible, the existing BIT
definitions for the port speeds are incremented by one
to maintain the original position.
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Yellow Carp Ethernet devices use the existing PCI ID but
the window settings for the indirect PCS access have been
altered. Add the check for Yellow Carp Ethernet devices to
use the new register values.
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Userspace can receive notification of MCTP address changes via
RTNLGRP_MCTP_IFADDR rtnetlink multicast group.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20211220023104.1965509-1-matt@codeconstruct.com.auSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Horatiu Vultur says:

====================
net: lan966x: Add switchdev and vlan support

This patch series extends lan966x with switchdev and vlan support.
The first patches just adds new registers and extend the MAC table to
handle the interrupts when a new address is learn/forget.

v7->v8:
- remove extra mac learn when the port leaves the bridge
- replace memcpy with ether_addr_copy
- change the order of operations in lan966x_switch_driver_init/exit
- refactor lan966x_port_bridge_flags

v6->v7:
- fix build issues when compiling as a module

v5->v6:
- fix issues with the singletones, they were not really singletons
- simplify the case where lan966x ports are added to bridges with foreign
  ports
- drop the cases NETDEV_PRE_UP and NETDEV_DOWN
- fix the change of MAC address
- drop the callbacks .ndo_set_features, .ndo_vlan_rx_add_vid,
  .ndo_vlan_rx_kill_vid
- remove duplicate code when port was added in a vlan, the MAC entries
  will be added by the fdb

v4->v5:
- make the notifier_block from lan966x to be singletones
- use switchdev_handle_port_obj_add and switchdev_handle_fdb_event_to_device
  when getting callbacks in the lan966x
- merge the two vlan patches in a single one

v3->v4:
- split the last patch in multiple patches
- replace spin_lock_irqsave/restore with spin_lock/spin_unlock
- remove lan966x_port_change_rx_flags because it was copying all the frames to
  the CPU instead of removing all RX filters.
- implement SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS
- remove calls to __dev_mc_unsync/sync as they are not needed
- replace 0/1 with false/true
- make sure that the lan966x ports are not added to bridges that have other
  interfaces except lan966x
- and allow the lan966x ports to be part of only the same bridge.

v2->v3:
- separate the PVID used when the port is in host mode or vlan unaware
- fix issue when the port was leaving the bridge

v1->v2:
- when allocating entries for the mac table use kzalloc instead of
  devm_kzalloc
- also use GFP_KERNEL instead of GFP_ATOMIC, because is never called
  in atomic context
- when deleting an mac table entry, the order of operations was wrong
- if ana irq is enabled make sure it gets disabled when the driver is
  removed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend lan966x driver with fdb support by implementing the switchdev
calls SWITCHDEV_FDB_ADD_TO_DEVICE and SWITCHDEV_FDB_DEL_TO_DEVICE.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently allow a port to be part or not of the multicast flooding mask.
By implementing the switchdev calls SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS
and SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the driver to support vlan filtering  by implementing the
switchdev calls SWITCHDEV_OBJ_ID_PORT_VLAN,
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds basic support to offload in the HW the forwarding of the
frames. The driver registers to the switchdev callbacks and implements
the callbacks for attributes SWITCHDEV_ATTR_ID_PORT_STP_STATE and
SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME.
It is not allowed to add a lan966x port to a bridge that contains a
different interface than lan966x.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function lan966x_port_change_rx_flags() was used only when
IFF_PROMISC flag was set. In that case it was setting to copy all the
frames to the CPU instead of removing any RX filters. Therefore remove
it.

Fixes: d28d6d2e ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for adding/removing mac entries in the SW list
of entries and in the HW table. This is used by the bridge
functionality.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for handling the interrupts generated by the
analyzer. Currently, only the MAC table generates these interrupts.
The MAC table will generate an interrupt whenever it learns or forgets
an entry in the table. It is the SW responsibility figure out which
entries were added/removed.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend dt-bindings for lan966x with analyzer interrupt.
This interrupt can be generated for example when the HW learn/forgets
an entry in the MAC table.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the registers that will be used to enable switchdev and
vlan functionality in the HW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: devlink health reporter extensions

This patchset extends the devlink health reporter registered by mlxsw to
report new health events and their related parameters. These are meant
to aid in debugging hardware and firmware issues.

Patches #1-#2 are preparations.

Patch #3 adds the definitions of the new events and parameters.

Patch #4 extends the health reporter to report the new events and
parameters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the devlink health reporter registered by mlxsw to report new
health events and their related parameters. These are meant to aid in
debugging of hardware / firmware issues.

Beside the test event ('MLXSW_REG_MFDE_EVENT_ID_TEST') that is triggered
following the devlink health 'test' sub-command, the new events are used
to report the triggering of asserts in firmware code
('MLXSW_REG_MFDE_EVENT_ID_FW_ASSERT') and hardware issues
('MLXSW_REG_MFDE_EVENT_ID_FATAL_CAUSE').

Each event is accompanied with a severity parameter and per-event
parameters that are meant to help root cause the detected issue.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the Monitoring Firmware Debug (MFDE) register with new events and
their related parameters. These events will be utilized by
devlink-health in the next patch.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert a series of if statements that handle different events to a
switch case statement. Encapsulate the per-event code in different
functions to simplify the code.

This is a preparation for subsequent patches that will add more events
that need to be handled.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the MFDE register field names are using the convention:
reg_mfde_<NAME_OF_FIELD>, and do not consider the name of the MFDE
event.

Fix the field names so they fit the more accurate convention:
reg_mfde_<NAME_OF_EVENT>_<NAME_OF_FIELD>.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0a6890b9 ("bnx2x: Utilize FW 7.13.15.0.")
added validation for fastpath HSI versions for different
client init which was not meant for SR-IOV VF clients, which
resulted in firmware asserts when running VF clients with
different fastpath HSI version.

This patch along with the new firmware support in patch #1
fixes this behavior in order to not validate fastpath HSI
version for the VFs.

Fixes: 0a6890b9 ("bnx2x: Utilize FW 7.13.15.0.")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This new firmware addresses few important issues and enhancements
as mentioned below -

- Support direct invalidation of FP HSI Ver per function ID, required for
  invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility

This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently cfg80211 checks for invalid channels whenever there is a
regulatory update and stops the active interfaces if it is operating on
an unsupported channel in the new regulatory domain.

This is done based on a regulatory flag REGULATORY_IGNORE_STALE_KICKOFF
set during wiphy registration which disables this enforcement when
unsupported interface modes are supported by driver.

Add support to enable this enforcement when Mesh Point interface type
is advertised by drivers.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1638409120-28997-1-git-send-email-quic_srirrama@quicinc.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi needs to be able to differentiate between the
software rfkill state and the hardware rfkill state.

The reason for this is that iwlwifi needs to notify any
change in the software rfkill state even when it doesn't
own the device (which means even when the hardware rfkill
is asserted).

In order to be able to know the software rfkill when the
host does not own the device, iwlwifi needs to be able to
ask the state of the software rfkill ignoring the state
of the hardware rfkill.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20211219195124.125689-1-emmanuel.grumbach@intel.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Now that this is no longer part of the bigger function,
we can get rid of the channel_num variable. Also change
the function to use the struct element helpers, instead
of open-coding the element handling.

Link: https://lore.kernel.org/r/20211202130913.a0adf67a9319.I6db0340a34fff18d78e9cd512f4abf855da4e43a@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Thinking about MLD (Draft 802.11be) now, it's clear that
we'll have new limitations where different stations (or
links) must be on _different_ channels (or in different
frequency ranges even.) Clarify that the current limit of
multiple channels is a maximum and the same one is OK.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20211201110924.2816d91b6862.I2d997abd525574529f88e941d90aeb640dbb1abf@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Add a flag attribute to use in ap settings to indicate userspace
supports offloading of SA Query procedures to driver. Also add AP SME
device feature flag to advertise that the SA Query procedures offloaded
to driver when userspace indicates support for offloading of SA Query
procedures.

Driver handles SA Query procedures in driver's SME it self and skip
sending SA Query request or response frames to userspace when userspace
indicates support for SA Query procedures offload. But if userspace
doesn't advertise support for SA Query procedures offload driver shall
not offload SA Query procedures handling.

Also userspace with SA Query procedures offload capability shall skip SA
Query specific validations when driver indicates support for handling SA
Query procedures.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/1637911519-21306-2-git-send-email-vjakkam@codeaurora.orgSigned-off-by: Johannes Berg <johannes.berg@intel.com>

In previous method each AP settings flag is represented by a top-level
flag attribute and conversion to enum cfg80211_ap_settings_flags had to
be done before sending them to driver. This commit is to make it easier
to define new AP settings flags and sending them to driver.

This commit also deprecate sending of
%NL80211_ATTR_EXTERNAL_AUTH_SUPPORT in %NL80211_CMD_START_AP. But to
maintain backwards compatibility checks for
%NL80211_ATTR_EXTERNAL_AUTH_SUPPORT in %NL80211_CMD_START_AP when
%NL80211_ATTR_AP_SETTINGS_FLAGS not present in %NL80211_CMD_START_AP.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/1637911519-21306-1-git-send-email-vjakkam@codeaurora.orgSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Add more logging in places that affect HT/VHT/HE state, so
things get easier to debug.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211130131608.ac51d574458c.If197b45c5b31d2fbd254fa12c2d7c736f304d4ae@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>