In a similar fashion to Spectrum-1, enforce a specific firmware version
for Spectrum-2 so that the driver and firmware are always in sync with
regards to new features.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The version adds support for querying port module type. It will be used
by a followup patch set from Jiri to make port split code more generic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SN3800 Spectrum-2 based systems have gearboxes that need to be
initialized by the firmware during its initialization flow. In certain
cases, the firmware might need to flash these gearboxes, which is
currently a time-consuming process.

In newer firmware versions, the firmware will not signal to the driver
that it is ready until the gearboxes are flashed. Increase the PCI reset
timeout for these situations. In normal cases, the driver will need to
wait no longer than 5 seconds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In new firmware versions this register is extended with a sampling rate
for Spectrum-2 and future ASICs.

Increase the size of the register to ensure the field is initialized to
0 which means every packet is mirrored.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lars Poeschel says:

====================
nfc: pn533: add uart phy driver

The purpose of this patch series is to add a uart phy driver to the
pn533 nfc driver.
It first changes the dt strings and docs. The dt compatible strings
need to change, because I would add "pn532-uart" to the already
existing "pn533-i2c" one. These two are now unified into just
"pn532". Then the neccessary changes to the pn533 core driver are
made. Then the uart phy is added.
As the pn532 chip supports a autopoll, I wanted to use this instead
of the software poll loop in the pn533 core driver. It is added and
activated by the last to patches.
The way to add the autopoll later in seperate patches is chosen, to
show, that the uart phy driver can also work with the software poll
loop, if someone needs that for some reason.
In v11 of this patchseries I address a byte ordering issue reported
by kbuild test robot in patch 5/7.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This switches the pn532 UART phy driver from manually polling to the new
autopoll mechanism.

Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

pn532 devices support an autopoll command, that lets the chip
automatically poll for selected nfc technologies instead of manually
looping through every single nfc technology the user is interested in.
This is faster and less cpu and bus intensive than manually polling.
This adds this autopoll capability to the pn533 driver.

Cc: Johan Hovold <johan@kernel.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the UART phy interface for the pn533 driver.
The pn533 driver can be used through UART interface this way.
It is implemented as a serdev device.

Cc: Johan Hovold <johan@kernel.org>
Cc: Claudiu Beznea <Claudiu.Beznea@microchip.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a problem in the initialisation and setup of the pn533: It
registers with nfc too early. It could happen, that it finished
registering with nfc and someone starts using it. But setup of the pn533
is not yet finished. Bad or at least unintended things could happen.
So I split out nfc registering (and unregistering) to seperate functions
that have to be called late in probe then.
i2c requires a bit more love: i2c requests an irq in it's probe
function. 'Commit 32ecc75d ("NFC: pn533: change order operations in
dev registation")' shows, this can not happen too early. An irq can be
served before structs are fully initialized. The way chosen to prevent
this is to request the irq after nfc_alloc_device initialized the
structs, but before nfc_register_device. So there is now this
pn532_i2c_nfc_alloc function.

Cc: Johan Hovold <johan@kernel.org>
Cc: Claudiu Beznea <Claudiu.Beznea@microchip.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds hooks for dev_up and dev_down to the phy_ops. They are
optional.
The idea is to inform the phy driver when the nfc chip is really going
to be used. When it is not used, the phy driver can suspend it's
interface to the nfc chip to save some power. The nfc chip is considered
not in use before dev_up and after dev_down.

Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds documentation about the uart phy to the pn532 binding doc. As
the filename "pn533-i2c.txt" is not appropriate any more, rename it to
the more general "pn532.txt".
This also documents the deprecation of the compatible strings ending
with "...-i2c".

Cc: Johan Hovold <johan@kernel.org>
Cc: Simon Horman <horms@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is favourable to have one unified compatible string for devices that
have multiple interfaces. So this adds simply "pn532" as the devicetree
binding compatible string and makes a note that the old ones are
deprecated.

Cc: Johan Hovold <johan@kernel.org>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
net: bridge: convert fdbs to use bitops

We'd like to have a well-defined behaviour when changing fdb flags. The
problem is that we've added new fields which are changed from all
contexts without any locking. We are aware of the bit test/change races
and these are fine (we can remove them later), but it is considered
undefined behaviour to change bitfields from multiple threads and also
on some architectures that can result in unexpected results,
specifically when all fields between the changed ones are also
bitfields. The conversion to bitops shows the intent clearly and
makes them use functions with well-defined behaviour in such cases.
There is no overhead for the fast-path, the bit changing functions are
used only in special cases when learning and in the slow path.
In addition this conversion allows us to simplify fdb flag handling and
avoid bugs for future bits (e.g. a forgetting to clear the new bit when
allocating a new fdb). All bridge selftests passed, also tried all of the
converted bits manually in a VM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to have separate arguments for each flag, just set the flags to
whatever was passed to fdb_create() before the fdb is published.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the offloaded field to a flag and use bitops.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the added_by_external_learn field to a flag and use bitops.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Straight-forward convert of the added_by_user field to bitops.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Straight-forward convert of the is_sticky field to bitops.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the is_static to bitops, make use of the combined
test_and_set/clear_bit to simplify expressions in fdb_add_entry.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds a new fdb flags field in the hole between the two cache
lines and uses it to convert is_local to bitops.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only smc-related reference in net/sock.h is struct smc_hashinfo.
But just its address is refered to. Thus there is no need for the
include of net/smc.h. Remove it.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, TIPC transports intra-node user data messages directly
socket to socket, hence shortcutting all the lower layers of the
communication stack. This gives TIPC very good intra node performance,
both regarding throughput and latency.

We now introduce a similar mechanism for TIPC data traffic across
network namespaces located in the same kernel. On the send path, the
call chain is as always accompanied by the sending node's network name
space pointer. However, once we have reliably established that the
receiving node is represented by a namespace on the same host, we just
replace the namespace pointer with the receiving node/namespace's
ditto, and follow the regular socket receive patch though the receiving
node. This technique gives us a throughput similar to the node internal
throughput, several times larger than if we let the traffic go though
the full network stacks. As a comparison, max throughput for 64k
messages is four times larger than TCP throughput for the same type of
traffic.

To meet any security concerns, the following should be noted.

- All nodes joining a cluster are supposed to have been be certified
and authenticated by mechanisms outside TIPC. This is no different for
nodes/namespaces on the same host; they have to auto discover each
other using the attached interfaces, and establish links which are
supervised via the regular link monitoring mechanism. Hence, a kernel
local node has no other way to join a cluster than any other node, and
have to obey to policies set in the IP or device layers of the stack.

- Only when a sender has established with 100% certainty that the peer
node is located in a kernel local namespace does it choose to let user
data messages, and only those, take the crossover path to the receiving
node/namespace.

- If the receiving node/namespace is removed, its namespace pointer
is invalidated at all peer nodes, and their neighbor link monitoring
will eventually note that this node is gone.

- To ensure the "100% certainty" criteria, and prevent any possible
spoofing, received discovery messages must contain a proof that the
sender knows a common secret. We use the hash mix of the sending
node/namespace for this purpose, since it can be accessed directly by
all other namespaces in the kernel. Upon reception of a discovery
message, the receiver checks this proof against all the local
namespaces'hash_mix:es. If it finds a match, that, along with a
matching node id and cluster id, this is deemed sufficient proof that
the peer node in question is in a local namespace, and a wormhole can
be opened.

- We should also consider that TIPC is intended to be a cluster local
IPC mechanism (just like e.g. UNIX sockets) rather than a network
protocol, and hence we think it can justified to allow it to shortcut the
lower protocol layers.

Regarding traceability, we should notice that since commit 6c9081a3
("tipc: add loopback device tracking") it is possible to follow the node
internal packet flow by just activating tcpdump on the loopback
interface. This will be true even for this mechanism; by activating
tcpdump on the involved nodes' loopback interfaces their inter-name
space messaging can easily be tracked.

v2:
- update 'net' pointer when node left/rejoined
v3:
- grab read/write lock when using node ref obj
v4:
- clone traffics between netns to loopback
Suggested-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot triggered struct net NULL deref in NF_HOOK_LIST:
RIP: 0010:NF_HOOK_LIST include/linux/netfilter.h:331 [inline]
RIP: 0010:ip6_sublist_rcv+0x5c9/0x930 net/ipv6/ip6_input.c:292
 ipv6_list_rcv+0x373/0x4b0 net/ipv6/ip6_input.c:328
 __netif_receive_skb_list_ptype net/core/dev.c:5274 [inline]

Reason:
void ipv6_list_rcv(struct list_head *head, struct packet_type *pt,
                   struct net_device *orig_dev)
[..]
        list_for_each_entry_safe(skb, next, head, list) {
		/* iterates list */
                skb = ip6_rcv_core(skb, dev, net);
		/* ip6_rcv_core drops skb -> NULL is returned */
                if (skb == NULL)
                        continue;
	[..]
	}
	/* sublist is empty -> curr_net is NULL */
        ip6_sublist_rcv(&sublist, curr_dev, curr_net);

Before the recent change NF_HOOK_LIST did a list iteration before
struct net deref, i.e. it was a no-op in the empty list case.

List iteration now happens after *net deref, causing crash.

Follow the same pattern as the ip(v6)_list_rcv loop and add a list_empty
test for the final sublist dispatch too.

Cc: Edward Cree <ecree@solarflare.com>
Reported-by: syzbot+c54f457cad330e57e967@syzkaller.appspotmail.com
Fixes: ca58fbe0 ("netfilter: add and use nf_hook_slow_list()")
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use true/false for bool type in bnxt_timer function.
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use true/false on bool type variables for assignment.
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: marvell: fix and extend downshift support

This series includes two fixes and two extensions for downshift support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

More PHY versions are compatible with the existing downshift
implementation, so let's add downshift support for them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds downshift support for M88E1111. This PHY version uses
another register for downshift configuration, reading downshift status
is possible via the same register as for other PHY versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I got access to the M88E1111 datasheet, and this PHY version uses
another register for downshift configuration. Therefore change prefix
to m88e1011, aligned with constants like MII_M1011_PHY_SCR.

Fixes: a3bdfce7 ("net: phy: marvell: support downshift as PHY tunable")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix typo and use PHY_SCR for PHY-specific Control Register.

Fixes: a3bdfce7 ("net: phy: marvell: support downshift as PHY tunable")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sync the ABI description with the interface statistics that are currently
available through sysfs.

CC: Jarod Wilson <jarod@redhat.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: linux-doc@vger.kernel.org
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/pensando/ionic/ionic_txrx.c: In function 'ionic_rx_empty':
drivers/net/ethernet/pensando/ionic/ionic_txrx.c:405:28: warning:
 variable 'sg_desc' set but not used [-Wunused-but-set-variable]

It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds WoL support on TI DP83867 for magic, magic secure, unicast and
broadcast.
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix currenty ignored returned error by properly checking *err* after
calling aq_nic->aq_hw_ops->hw_ring_hwts_rx_fill().

Addresses-Coverity-ID: 1487357 ("Unused value")
Fixes: 04a18399 ("net: aquantia: implement data PTP datapath")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When NET_DSA_SMSC_LAN9303=y and NET_DSA_SMSC_LAN9303_MDIO=y,
below errors can be seen:
drivers/net/dsa/lan9303_mdio.c:87:23: error: REGMAP_ENDIAN_LITTLE
undeclared here (not in a function)
  .reg_format_endian = REGMAP_ENDIAN_LITTLE,
drivers/net/dsa/lan9303_mdio.c:93:3: error: const struct regmap_config
has no member named reg_read
  .reg_read = lan9303_mdio_read,

It should select REGMAP in config NET_DSA_SMSC_LAN9303.

Fixes: dc700583 ("net: dsa: LAN9303: add MDIO managed mode support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using ARCH=mips CROSS_COMPILE=mips-linux-gnu-
to build drivers/net/ethernet/aquantia/atlantic/aq_ptp.o
and drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.o,
below errors can be seen:
drivers/net/ethernet/aquantia/atlantic/aq_ptp.c:1378:6:
warning: symbol 'aq_ptp_poll_sync_work_cb' was not declared.
Should it be static?

drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.c:1155:5:
warning: symbol 'hw_atl_b0_ts_to_sys_clock' was not declared.
Should it be static?

This patch to make aq_ptp_poll_sync_work_cb and hw_atl_b0_ts_to_sys_clock
be static to fix these warnings.

Fixes: 9c477032 ("net: aquantia: add support for PIN funcs")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2019-10-25

This series contains updates to i40e only.  Several are fixes that could
go to 'net', but were intended for 'net-next'.

Sylwia changes how the driver function to read the NVM module data, so
that it is able to read the LLDP agent configuration to allow for
persistent LLDP.

Jaroslaw resolves an issue where the incorrect FEC settings were being
displayed in ethtool, by setting the proper FEC bits.

Piotr moves the hardware flags detection into a separate function, so
that the specific flags can be set based on the MAC and NVM.  Also
extends the PHY access function to include a command flag to let the
firmware know it should not change the page while accessing a OSFP module.
Updates the driver to display the driver and firmware version when in
recovery mode.

Aleksandr refactored the VF MAC filters accounting since an untrusted
VF was able to delete but not add a MAC filter, so refactor the code to
have more consistency and improved logging.

Nicholas updates the driver to use a default interval of 50 usecs,
instead of the current 100 usecs which was causing some regression
performance issues.

Damian resolved LED blinking issues for X710T*L devices by adding
specific flows for these devices in the LED operations.

Navid Emamdoost found where allocated memory is not being properly freed
upon a failure in setting up MAC VLANs, so added the missing kfree().

v2: Dropped patches 2 & 6 from the original series while we wait for the
    author to respond to community feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The pointer bdp is being assigned with a value that is never
read, so the assignment is redundant and hence can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return directly from within the loop as soon as the port is found,
otherwise we won't return NULL if the end of the list is reached.

Fixes: b96ddf25 ("net: dsa: use ports list in dsa_to_port")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>