From: Russell King <rmk@armlinux.org.uk>
As per the patches posted, discussed and tested by Peter Rosin, this
converts TDA998x to a bridge driver, while still allowing Armada and
TI LCDC to continue using it as they always have done.  It also gets
rid of the private .fill_modes function, and tweaks the TMDS divider
calculation to be more correct to the available information.

[airlied: fixed two conflicts]
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802093421.GA29670@rmk-PC.armlinux.org.uk

From: Liviu Dudau <Liviu.Dudau@arm.com>
"I managed to loose track of a few patches for HDLCD while focusing
on Mali DP and found them again when investigating an issue with
the way HDLCD behaves on teardown. They can go into drm-next for
one of the v4.19-rcX if you're not going to do another pull request
before the merge window."
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731170831.GF17455@e110455-lin.cambridge.arm.com

The serializer PLL divider is a power-of-two divider, so our calculation
which assumes that it's a numerical divider is incorrect.  Replace it
with one that results in a power-of-two divider value instead.

Tested with all supported modes with a Samsung S24C750.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

We can achieve the same effect via the get_modes() method, rather than
wrapping the fill_modes helper.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Move the mode_valid() implementation to the bridge instead of the
connector, as we're checking the bridge's capabilities.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Register the bridge outside of the component helper as we have
drivers that wish to use the tda998x without its encoder.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Cleanup the code a little from the effects of the previous changes:
- Move tda998x_destroy() to be above tda998x_create()
- Use 'dev' directly in tda998x_create() where appropriate.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Move the tda998x_priv allocation inside tda998x_create() and simplify
the tda998x_create()'s arguments.  Pass the same to tda998x_destroy().
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Convert tda998x to a bridge driver with built-in encoder support for
compatibility with existing component drivers.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Move the non-DT configuration of the TDA998x into tda998x_create()
so that we do all setup in one place.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

This fits better with the drm_bridge callbacks for when this
driver becomes a drm_bridge.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
[edited by rmk to just split the tda998x_encoder_dpms() function
 and restore the double-disable protection we originally had,
 preserving original behaviour.]
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

This prepares for being a drm_bridge which will not register the
encoder. That makes the connector the better choice.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

This set of changes migrates Armada DRM from legacy modeset to atomic
modeset.  This is everything from the "Transition Armada DRM planes to
atomic state" and "Finish Armada DRM transition to atomic modeset"
patch sets as posted on drm-devel, excluding the "Finish Armada DRM DT
support" series.

These series did not evoke any comments - if there are any, these can
be addressed via follow up patches.

Developed and tested on Dove Cubox with xf86-video-armada including the
overlay plane, and also tested with the tools in libdrm.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180730110543.GA30664@rmk-PC.armlinux.org.uk

A bit larger this time around, due to introduction of "dpu1" support
for the display controller in sdm845 and beyond.  This has been on
list and undergoing refactoring since Feb (going from ~110kloc to
~30kloc), and all my review complaints have been addressed, so I'd be
happy to see this upstream so further feature work can procede on top
of upstream.

Also includes the gpu coredump support, which should be useful for
debugging gpu crashes.  And various other misc fixes and such.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv-8y3zguY0Mj1vh=o+vrv_bJ8AwZ96wBXYPvMeQT2XcA@mail.gmail.com

The HDLCD engine needs an active plane while the CRTC is active, as
it will start scanning out data from HDLCD_REG_FB_BASE once it gets
enabled. Make sure that the only available plane doesn't get disabled
while the CRTC remains active, as this will scanout invalid data.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

The plane cleanup handler currently calls drm_plane_helper_disable(),
which is a legacy helper function. Replace it with a call to
drm_atomic_helper_shutdown() at removal time. The plane .destroy()
handler now consisting only of a call to drm_plane_cleanup(), replace it
with direct calls to that function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

The top-level error handler calls drm_mode_config_cleanup() which will
destroy all planes. There's no need to destroy them manually in lower
error handlers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Use drm_fb_cma_fbdev_init() and drm_fb_cma_fbdev_fini() which relies on
the fact that drm_device holds a pointer to the drm_fb_helper structure.
This means that the driver doesn't have to keep track of that.
Also use the drm_fb_helper functions directly.

Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Replace driver's code with the generic helpers that do the same thing
including the NULL check.

Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

A set of cleanups and fixes for Mikulas for using udl on arm boards.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAPM=9twQNgrmfe0=Okq1NTgWHRQXy+AzeDy8A0p_-y856p4vtA@mail.gmail.com

The udl kms driver writes messages to the syslog whenever some application
opens or closes /dev/fb0 and whenever the user switches between the
Xserver and the console.

This patch changes the priority of these messages to debug.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

spin_lock_irqsave and spin_unlock_irqrestore is inteded to be called from
a context where it is unknown if interrupts are enabled or disabled (such
as interrupt handlers). From a process context, we should call
spin_lock_irq and spin_unlock_irq, that avoids the costly pushf and popf
instructions.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Modern processors can detect linear memory accesses and prefetch data
automatically, so there's no need to use prefetch.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Division is slow, so it shouldn't be done by the pixel generating code.
The driver supports only 2 or 4 bytes per pixel, so we can replace
division with a shift.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

We must use kzalloc when allocating the fb_deferred_io structure.
Otherwise, the field first_io is undefined and it causes a crash.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Allocations larger than PAGE_ALLOC_COSTLY_ORDER are unreliable and they
may fail anytime. This patch fixes the udl kms driver so that when a large
alloactions fails, it tries to do multiple smaller allocations.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

If we leave urbs around, it causes not only leak, but also memory
corruption. This patch fixes the function udl_free_urb_list, so that it
always waits for all urbs that are in progress.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Adds bindings for Snapdragon 845 display processing unit

Changes in v2:
- Use SoC specific compatibles for mdss and dpu (Rob Herring)
- Use assigned-clocks to set initial clock frequency (Rob Herring)

Changes in v3 (all suggested by Rob Herring):
- Rename mdss_phys to mdss
- Correct description for clocks/assigned-clocks
- Rename mdp_phys to mdp
- Rename vbif_phys to vbif
- Remove redundant interrupt-parent from mdss_mdp
- Fully specify 'ranges' and use relative reg address in mdss_mdp

Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Rajesh Yadav <ryadav@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Adds mdp transfer time to msm dsi binding

Changes in v3:
- Added Rob's R-b
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Rajesh Yadav <ryadav@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Mark a number of static functions that are only unsed in the file
that defines them and remove the prototypes from the headers where
needed.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Remove dpu_format_get_block_size, dpu_format_get_framebuffer_size,
dpu_set_scaler_v2 and dpu_copy_formats they are unused and unneeded.
Signed-off-by: Jordan Crouse <jcrouse@codeauorora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

None of the functions in dpu_kms_utils.c seem to be used so
remove them all.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Remove a chunk of unused code from drm_crtc.c, namely
dpu_crtc_res_add, dpu_crtc_res_get, dpu_crtc_res_put
and associated static functions.

Also zap dpu_crtc_event_queue(), helper functions
and members.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Remove dpu_encoder_check_mode and dpu_encoder_helper_hw_release
frmo drm_encoder.c as they appear to be unused.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

PTR_RET is deprecated, use PTR_ERR_OR_ZERO instead.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The suspend/resume functions are not referenced when power
management is disabled:

drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c:1288:12: error: 'dpu_runtime_resume' defined but not used [-Werror=unused-function]
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c:1261:12: error: 'dpu_runtime_suspend' defined but not used [-Werror=unused-function]

This marks them as __maybe_unused to let the compiler
drop the functions without complaining.

Fixes: 591225291ca2 ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Fix the sparse error. the dpu_rm_init declaration is not consistent
with the implement.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
[robclark un-typo'd subject line]
Signed-off-by: Rob Clark <robdclark@gmail.com>

All users of do_gettimeofday() have been removed, but this one recently
crept in, along with an incorrect printing of the microseconds portion.

This converts it to using ktime_get_real_timespec64() as a direct
replacement, and adds the leading zeroes. I considered using monotonic
times (ktime_get()) instead, but as this timestamp appears to only
be used for humans rather than compared with other timestamps, the
real time domain is probably good enough.

Fixes: e43b045e2c82 ("drm/msm/gpu: Capture the state of the GPU")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>

This fixes up a collision between introducing dual-channel support and
the dsi refactors. This patch applies the same dual-channel
considerations and pclk calculations to both v2 and 6G, with a bit of
abstracting for good measure.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

In these cases, we want to enumerate _all_ clocks, not just the ones
that are assigned a rate.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>