- 11 Feb, 2021 2 commits
-
-
Casey Bowman authored
Increasing the virtual timeout time to account for scenarios that may require more time, like DisplayPort Multi-Stream Transport (DP MST), where the disconnect time can be extended longer than usual. The recommended timeout range is 5-10 seconds, of which we will take the lower bound. Signed-off-by:
Casey Bowman <casey.g.bowman@intel.com> Acked-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20210210192041.17022-1-casey.g.bowman@intel.comSigned-off-by:
Hans de Goede <hdegoede@redhat.com>
-
Maximilian Luz authored
The raw message frame length is unaligned and explicitly marked as little endian. It should not be accessed without the appropriate accessor functions. Fix this. Note that payload.len already contains the correct length after parsing via sshp_parse_frame(), so we can simply use that instead. Reported-by:
kernel-test-robot <lkp@intel.com> Fixes: c167b9c7 ("platform/surface: Add Surface Aggregator subsystem") Signed-off-by:
Maximilian Luz <luzmaximilian@gmail.com> Acked-by:
Mark Gross <mgross@linux.intel.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210211124149.2439007-1-luzmaximilian@gmail.comSigned-off-by:
-
- 09 Feb, 2021 1 commit
-
-
Hans de Goede authored
-
- 08 Feb, 2021 5 commits
-
-
Srinivas Pandruvada authored
Update version for changes released with v5.12 kernel release. Signed-off-by:Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
-
Srinivas Pandruvada authored
Add a new command to get and set TRL (Turbo Ratio Limits). This will help users to get/set TRL, when the direct MSR access is removed. Signed-off-by: -
Srinivas Pandruvada authored
Add a new command "turbo-mode", which allows to enable/disable turbo mode globally. This uses base-frequency as the max frequency when turbo-mode is disabled. This allows soft disable turbo mode without depending on kernel or BIOS. Signed-off-by: -
Rikard Falkeborn authored
The only usage of it is to assign its address to the ops field in the regulator_desc struct, which is a pointer to const struct regulator_ops. Make it const to allow the compiler to put it in read-only memory. Signed-off-by:
Rikard Falkeborn <rikard.falkeborn@gmail.com> Link: https://lore.kernel.org/r/20210206232152.58046-1-rikard.falkeborn@gmail.comSigned-off-by:
-
Maximilian Luz authored
Some Surface Book 2 and 3 models have a discrete GPU (dGPU) that is hot-pluggable. On those devices, the dGPU is contained in the base, which can be separated from the tablet part (containing CPU and touchscreen) while the device is running. It (in general) is presented as/behaves like a standard PCIe hot-plug capable device, however, this device can also be put into D3cold. In D3cold, the device itself is turned off and can thus not submit any standard PCIe hot-plug events. To properly detect hot-(un)plugging while the dGPU is in D3cold, out-of-band signaling is required. Without this, the device state will only get updated during the next bus-check, eg. via a manually issued lspci call. This commit adds a driver to handle out-of-band PCIe hot-(un)plug events on Microsoft Surface devices. On those devices, said events can be detected via GPIO interrupts, which are then forwarded to the corresponding ACPI DSM calls by this driver. The DSM then takes care of issuing the appropriate bus-/device-check, causing the PCI core to properly pick up the device change. Signed-off-by:
-
- 04 Feb, 2021 32 commits
-
-
Andy Shevchenko authored
Neither original structure nor platform_data is declared with const. Drop mistakenly added const when assing platform_data. Fixes: a507e5d9 ("platform/x86: intel_scu_wdt: Get rid of custom x86 model comparison") Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
Barnabás Pőcze authored
LED class support is needed by the ideapad-laptop module to compile after the referenced commit. Add missing NEW_LEDS and LEDS_CLASS to Kconfig. Fixes: 503325f8 ("platform/x86: ideapad-laptop: add keyboard backlight control support") Signed-off-by:
Barnabás Pőcze <pobrn@protonmail.com> Link: https://lore.kernel.org/r/20210204142010.356675-1-pobrn@protonmail.comSigned-off-by:
-
Hans de Goede authored
ACPI_EXCEPTION is only intended for internal use by the ACPICA code. ACPI_EXCEPTION was being used here to change the apci_status code into something human-readable, use acpi_format_exception() for this instead, which is the proper way to do this outside of ACPICA. Signed-off-by:
-
Hans de Goede authored
With the #if IS_ENABLED(CONFIG_ACPI_PLATFORM_PROFILE), we get the following errors when thinkpad_acpi is builtin while CONFIG_ACPI_PLATFORM_PROFILE=m : drivers/platform/x86/thinkpad_acpi.c:10186: undefined reference to `platform_profile_notify' drivers/platform/x86/thinkpad_acpi.c:10226: undefined reference to `platform_profile_register' drivers/platform/x86/thinkpad_acpi.c:10246: undefined reference to `platform_profile_remove' This could be fixed by changing the IS_ENABLED to IS_REACHABLE, but I believe that it is better to just switch to using depends on. Using depends on ensures that platform-profile support is always available when thinkpad_acpi is build, hopefully leading to less confusing bug-reports about it sometimes not working. Cc: Mark Pearson <markpearson@lenovo.com> Signed-off-by:
-
Hans de Goede authored
Some of the new dytc handling functions are not marked static, even though they are only used internally. Mark these static, fixing the following compiler warnings: drivers/platform/x86/thinkpad_acpi.c:10081:5: warning: no previous prototype for 'dytc_profile_get' [-Wmissing-prototypes] drivers/platform/x86/thinkpad_acpi.c:10095:5: warning: no previous prototype for 'dytc_cql_command' [-Wmissing-prototypes] drivers/platform/x86/thinkpad_acpi.c:10133:5: warning: no previous prototype for 'dytc_profile_set' [-Wmissing-prototypes] Cc: Mark Pearson <markpearson@lenovo.com> Signed-off-by:
-
Hans de Goede authored
Explicitly check the status rather then relying on output.pointer staying NULL on an error. Reported-by:
-
Hans de Goede authored
Explicitly check the status rather then relying on output.pointer staying NULL on an error. This silences the following compiler warning: drivers/platform/surface/surface3-wmi.c:60:14: warning: variable 'status' set but not used [-Wunused-but-set-variable] Reported-by:
-
Mario Limonciello authored
A user without a Dell system doesn't need to pick any of these drivers. Users with a Dell system can enable this submenu and all drivers behind it will be enabled. Suggested-by:
Mario Limonciello <mario.limonciello@dell.com> Link: https://lore.kernel.org/r/20210203195832.2950605-1-mario.limonciello@dell.comReviewed-by:
-
Barnabás Pőcze authored
Document the conservation_mode attributes provided by the ideapad-laptop module. Fixes: ade50296 ("platform/x86: ideapad-laptop: Expose conservation mode switch") Signed-off-by:
-
Barnabás Pőcze authored
The documentation referred to non-existent device attributes under a non-existent platform device. Update it with the current location of the attributes. Fixes: b5c37b79 ("ideapad_laptop: convert ideapad device/driver to platform bus") Signed-off-by:
-
Barnabás Pőcze authored
Certain models have a so-called "always on USB charging" feature, which enables USB charging even when the computer is turned off or suspended, and which may be controlled/queried using the SALS/HALS ACPI methods. Expose this functionality via a new device attribute (usb_charging). Tested on: Lenovo YOGA 520-14IKB 80X8 Signed-off-by:
-
Barnabás Pőcze authored
On certain models it is possible to control/query the keyboard backlight via the SALS/HALS ACPI methods. Add support for that, and register an LED class device to expose this functionality. Tested on: Lenovo YOGA 520-14IKB 80X8 Signed-off-by:
-
Barnabás Pőcze authored
Consumers can determine if the value of an attribute changed much more easily if changes are broadcast using sysfs_notify(), so utilize it. Signed-off-by:
-
Barnabás Pőcze authored
Fix all checkpatch warnings. Reorder variable definitions from longest to shortest. Add more whitespaces for better readability. Rename variables named `ret` to `err` where appropriate. Reorder sysfs attributes show/store callbacks and the `ideapad_attributes` array in lexicographic order. And other minor formatting changes. No significant functional changes are intended. Signed-off-by:
-
Barnabás Pőcze authored
The touchpad can be enabled/disabled via this attribute on a Lenovo Yoga 520-14IKB. Allow writing as it provides legitimate functionality. This reverts commit 7f363145. Signed-off-by:
-
Barnabás Pőcze authored
Minor formatting changes. Use seq_puts() where possible. Signed-off-by:
-
Barnabás Pőcze authored
Remove conservation mode reporting since it is already reported via the appropriate device attribute, and its state can be deduced from the value of GBMD. Add the return value of the GBMD and HALS ACPI methods to the output. Use seq_puts() where possible. Signed-off-by:
-
Barnabás Pőcze authored
Bit 30 of _CFG is set if the device has a touchpad, check that in is_visible() for the touchpad attribute. Show 'touchpad', if supported, in the list of capabilities in the 'cfg' debugfs file. Signed-off-by:
-
Barnabás Pőcze authored
Bit 9 in the return value of the HALS ACPI method is set if Fn-lock is supported. Change ideapad_check_features() to check it. Signed-off-by:
-
Barnabás Pőcze authored
Store the supported features in the driver private data, and modify the is_visible() callback to use it, and create ideapad_check_features() to populate it. Signed-off-by:
-
Barnabás Pőcze authored
Create dedicated helper functions for accessing the main ACPI methods: GBMD, SMBC, HALS, SALS; and utilize them. Use `unsigned long` consistently in every ACPI helper wherever possible. Change names to better express purpose. Do not assign values to output parameters in case of failure. Signed-off-by:
-
Barnabás Pőcze authored
Group and rename constants depending on which ACPI interface they pertain to, and rename CFG_X constants to CFG_CAP_X. Signed-off-by:
-
Barnabás Pőcze authored
Do not handle zero length buffer separately. Use kstrtouint() instead of sscanf(). Use kstrtobool() in store_ideapad_cam(). These introduce minor ABI changes, but it is expected that no users rely on the previous behavior. Thus the change is deemed justifed. Additionally, use `!!` to convert to `int` and use the "%d" format specifier in sysfs_emit() for boolean-like attributes. Signed-off-by:
-
Barnabás Pőcze authored
Consumers can differentiate an error from a successful read much more easily if the read() call fails with an appropriate errno instead of returning a magic string like "-1". This introduces an ABI change, but not many users are expected to be relying on the previous behavior, and this change makes this module conforming to the standard behavior that sysfs attribute show/store callbacks return an appropriate errno in case of failure. Thus the ABI breakage is deemed justified. Signed-off-by:
-
Barnabás Pőcze authored
ACPI helpers returned -1 in case of failure. Convert these functions to return appropriate error codes, and convert their users to propagate these error codes accordingly. Signed-off-by:
-
Barnabás Pőcze authored
Having the device name in the log message makes it easier to determine in the context of which device the message was printed, so utilize the appropriate variants of dev_{err,warn,...} when printing log messages. Signed-off-by: -
Barnabás Pőcze authored
The current code used a hand-crafted formula to convert milliseconds to jiffies, replace it with the msecs_to_jiffies() function. Furthermore, use a while loop instead of for loop for shorter lines and simplicity. Signed-off-by:
-
Barnabás Pőcze authored
The current code used the combination of a for loop + test_bit, which can be simplified using for_each_set_bit(), so utilize that. Signed-off-by:
-
Barnabás Pőcze authored
Use kobj_to_dev() instead of open-coding the container_of() macro. Signed-off-by:
-
Barnabás Pőcze authored
Use device_{add,remove}_group instead of sysfs_{add,remove}_group. Signed-off-by: -
Barnabás Pőcze authored
sysfs_emit() has been introduced to make it less ambiguous which function is preferred when writing to the output buffer in a device attribute's show() callback. Convert the ideapad-laptop module to utilize this new helper function. Signed-off-by:
-
Barnabás Pőcze authored
ideapad_dytc_profile_exit() is not called in ideapad_acpi_add() in the error path. Add the missing call. Signed-off-by:
-
