The sja1105 hardware has a quirk in that some changes require a switch
reset, which loses all configuration. When the reset is initiated,
everything needs to be reprogrammed, including the MACs and the PCS.
This is currently done in sja1105_static_config_reload() - we manually
call sja1105_adjust_port_config(), sja1105_sgmii_pcs_config() and
sja1105_sgmii_pcs_force_speed() which are all internal functions.

There is a desire for sja1105 to use the common xpcs driver, and that
means that the equivalents of those functions, xpcs_do_config() and
xpcs_link_up() respectively, will no longer be local functions.

Forcing phylink to retrigger a resolve somehow, say by doing dev_close()
followed by dev_open() is not really an option, because the CPU port
might have a PCS as well, and there is no net device which we can close
and reopen for that. Additionally, the dev_close/dev_open sequence might
force a renegotiation of the copper-side link for SGMII ports connected
to a PHY, and this is undesirable as well, because the switch reset is
much quicker than a PHY autoneg, so we would have a lot more downtime.

The only solution I see is for the sja1105 driver to keep doing what
it's doing, and that means we need to export the equivalents from xpcs
for sja1105_sgmii_pcs_config and sja1105_sgmii_pcs_force_speed, and call
them directly in sja1105_static_config_reload(). This will be done
during the conversion patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The NXP SJA1110 switch integrates its own, non-Synopsys PMA, but it
manages it through the register space of the XPCS itself, in a small
register window inside MDIO_MMD_VEND2 from address 0x8030 to 0x806e.

This coincides with where the registers for the default Synopsys PMA
are, but the register definitions are of course not the same.

This situation is an odd hardware quirk, but the simplest way to manage
it is to drive the SJA1110's PMA from within the XPCS driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The NXP SJA1105 DSA switch integrates a Synopsys SGMII XPCS on port 4.
The generic code works fine, except there is an integration issue which
needs to be dealt with: in this switch, the XPCS is integrated with a
PMA that has the TX lane polarity inverted by default (PLUS is MINUS,
MINUS is PLUS).

To obtain normal non-inverted behavior, the TX lane polarity must be
inverted in the PCS, via the DIGITAL_CONTROL_2 register.

We introduce a pma_config() method in xpcs_compat which is called by the
phylink_pcs_config() implementation.

Also, the NXP SJA1105 returns all zeroes in the PHY ID registers 2 and 3.
We need to hack up an ad-hoc PHY ID (OUI is zero, device ID is 1) in
order for the XPCS driver to recognize it. This PHY ID is added to the
public include/linux/pcs/pcs-xpcs.h for that reason (for the sja1105
driver to be able to use it in a later patch).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xpcs_get_id() searches multiple MMDs for a known PHY ID, starting with
MDIO_MMD_PCS (3). However not all integrators might have implemented
that MMD on their MDIO bus. For example, the NXP SJA1105 and SJA1110
switches only implement vendor-specific MMD 1 and 2.

When there is nothing on an MDIO bus at a certain address, traditionally
the bus returns 0xffff, which means that the bus remained in its default
pull-up state for the duration of the MDIO transaction. The 0xffff value
is widely used in drivers/net/phy/phy_device.c (see get_phy_c22_id for
example) to denote a missing device.

So it makes sense for the xpcs to ignore this value as well, and
continue its search, eventually finding the proper PHY ID in the
vendor-specific MMDs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In fixed-link use cases, the XPCS can disable the clause 37 in-band
autoneg process, disable the "Automatic Speed Mode Change after CL37 AN"
setting, and force operation in a speed dictated by management.

Add support for this operating mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vendors which integrate the Designware XPCS might modify a few things
here and there, and to support those, it's best to create separate C
files in order to not clutter up the main pcs-xpcs.c.

Because the vendor files might want to access the common xpcs registers
too, let's move them in a header file which is local to this driver and
can be included by vendor files as appropriate.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no reason to embed an if within an if, we can just logically
AND the two conditions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reorder the variable declarations in descending line length order,
according to the networking coding style.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The struct mdio_xpcs_args is reminiscent of when a similarly named
struct mdio_xpcs_ops existed. Now that that is removed, we can shorten
the name to dw_xpcs (dw for DesignWare).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: qualcomm: rmnet: MAPv4 download checksum cleanup, part 1

I'm posting a large series an two smaller parts; this is part 1.

The RMNet driver handles MAP (or QMAP) protocol traffic.  There are
several versions of this protocol.  Version 1 supports multiplexing,
as well as aggregation of packets in a single buffer.  Version 4
adds the ability to perform checksum offload.  And version 5
implements checksum offload in a different way from version 4.

This series involves only MAPv4 protocol checksum offload, and only
in the download (RX) direction.  It affects handling of checksums
computed by hardware for UDP datagrams and TCP segments, carried
over both IPv4 and IPv6.

MAP packets arriving on an RMNet port implementing MAPv4 checksum
offload are passed to rmnet_map_checksum_downlink_packet() for
handling.

The packet is then passed to rmnet_map_ipv4_dl_csum_trailer() or
rmnet_map_ipv6_dl_csum_trailer(), depending contents of the MAP
payload.  These two functions interpret checksum metadata to
determine whether the checksum in the received packet matches that
calculated by the hardware.

It is these two functions that are the subject of this series (parts
1 and 2).  The bulk of these functions are transformed--in a lot of
small steps--from an extremely difficult-to-follow block of checksum
processing code into a fairly simple, heavily commented equivalent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In the previous patch IPv4 download checksum offload code was
updated to avoid unnecessary byte swapping, based on properties of
the Internet checksum algorithm.  This patch makes comparable
changes to the IPv6 download checksum offload handling.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Internet checksums are used for IPv4 header checksum, as well as TCP
segment and UDP datagram checksums.  Such a checksum represents the
negated sum of adjacent pairs of bytes, using ones' complement
arithmetic.

One property of the Internet checkum is byte order independence [1].
Specifically, the sum of byte-swapped pairs is equal to the result
of byte swapping the sum of those same pairs when not byte-swapped.

So for example if a, b, c, d, y, and z are hexadecimal digits, and
PLUS represents ones' complement addition:
    If:		ab PLUS cd = yz
    Then:	ba PLUS dc = zy

For this reason, there is no need to swap the order of bytes in the
checksum value held in a message header, nor the one in the QMAPv4
trailer, in order to operate on them.

In other words, we can determine whether the hardware-computed
checksum matches the one in the message header without any byte
swaps.

(This patch leaves in place all existing type casts.)

[1] https://tools.ietf.org/html/rfc1071Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In rmnet_map_ipv6_dl_csum_trailer() there is an especially involved
line of code that determines the ones' complement sum of the IPv6
packet header (in host byte order).  Simplify that by storing the
result of computing just the header checksum in a local variable,
then using that in the original assignment.

Use the size of the IPv6 header structure as the number of bytes to
checksum, rather than computing the offset to the transport header.
And use ip_fast_csum() rather than ipa_compute_csum(), knowing that
the size of an IPv6 header (40 bytes) is a multiple of 4 bytes
greater than 16.

Add some comments to match rmnet_map_ipv4_dl_csum_trailer().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In rmnet_map_ipv4_dl_csum_trailer(), an illegal checksum subtraction
is done, subtracting hdr_csum (in host byte order) from csum_value (in
network byte order).  Despite being illegal, it generally works,
because it turns out the value subtracted is (or should be) always 0,
which has the same representation in either byte order.

Doing illegal operations is not good form though, so fix this by
verifying the IP header checksum early in that function.  If its
checksum is non-zero, the packet will be bad, so just return an
error.  This will cause the packet to passed to the IP layer where
it can be dropped.

Thereafter, there is no need subtract the IP header checksum from
the checksum value in the trailer because we know it is zero.
Add a comment explaining this.

This type of packet error is different from other types, so add a
new statistics counter to track this condition.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The checksum fields of the TCP and UDP header structures already
have type __sum16.  We don't support any other protocol headers, so
we can simplify rmnet_map_get_csum_field(), getting rid of the local
variable entirely and just returning the appropriate address.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The value passed as an argument to rmnet_map_ipv4_ul_csum_header()
is always an IPv4 header.  Rather than using a local variable, just
have the type of the argument reflect the proper type.

In rmnet_map_ipv6_ul_csum_header() things are defined a little
differently, but make the same basic change there.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If IPV6 is not enabled in the kernel configuration, the RMNet
checksum code indicates a buffer containing an IPv6 packet is not
supported.  The same thing happens if a buffer contains something
other than an IPv4 or IPv6 packet.

We can rearrange things a bit in two functions so that some #ifdef
calls can simply be eliminated.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In rmnet_map_ipv4_dl_csum_trailer() use ip_is_fragment() to
determine whether a socket buffer contains a packet fragment.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Jake Keller says:

====================
100GbE Intel Wired LAN Driver Updates 2021-06-11

Extend the ice driver to support basic PTP clock functionality for E810
devices.

This includes some tangential work required to setup the sideband queue and
driver shared parameters as well.

This series only supports E810-based devices. This is because other devices
based on the E822 MAC use a different and more complex PHY.

The low level device functionality is kept within ice_ptp_hw.c and is
designed to be extensible for supporting E822 devices in a future series.

This series also only supports very basic functionality including the
ptp_clock device and timestamping. Support for configuring periodic outputs
and external input timestamps will be implemented in a future series.

There are a couple of potential "what? why?" bits in this series I want to
point out:

1) the PTP hardware functionality is shared between multiple functions. This
means that the same clock registers are shared across multiple PFs. In order
to avoid contention or clashing between PFs, firmware assigns "ownership" to
one PF, while other PFs are merely "associated" with the timer. Because we
share the hardware resource, only the clock owner will allocate and register
a PTP clock device. Other PFs determine the appropriate PTP clock index to
report by using a firmware interface to read a shared parameter that is set
by the owning PF.

2) the ice driver uses its own kthread instead of using do_aux_work. This is
because the periodic and asynchronous tasks are necessary for all PFs, but
only one PF will allocate the clock.

The series is broken up into functional pieces to allow easy review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Arseny Krasnov says:

====================
virtio/vsock: introduce SOCK_SEQPACKET support

This patchset implements support of SOCK_SEQPACKET for virtio
transport.
	As SOCK_SEQPACKET guarantees to save record boundaries, so to
do it, new bit for field 'flags' was added: SEQ_EOR. This bit is
set to 1 in last RW packet of message.
	Now as  packets of one socket are not reordered neither on vsock
nor on vhost transport layers, such bit allows to restore original
message on receiver's side. If user's buffer is smaller than message
length, when all out of size data is dropped.
	Maximum length of datagram is limited by 'peer_buf_alloc' value.
	Implementation also supports 'MSG_TRUNC' flags.
	Tests also implemented.

	Thanks to stsp2@yandex.ru for encouragements and initial design
recommendations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add SEQPACKET socket type to vsock trace event.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement two tests of SOCK_SEQPACKET socket: first sends data by
several 'write()'s and checks that number of 'read()' were same.
Second test checks MSG_TRUNC flag. Cases for connect(), bind(),
etc. are not tested, because it is same as for stream socket.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add SEQPACKET ops for loopback transport and 'seqpacket_allow()'
callback.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When received packet is copied to guests's rx queue, data buffers
of rx queue could be smaller that data buffer of input packet, so
data of input packet is copied to each rx buffer, thus each rx
buffer will be a packet with dynamically created header. Fields
of such header are initialized from header of input packet(except
length field which value is depends on number of bytes copied to
rx buffer). But in SEQPACKET case, we also need to take care of
record delimeter bit: if input packet has this bit set, we don't
copy it to header of packet in rx buffer, except case when such
rx buffer is last part of input packet. Otherwise, we will get
sequence of packets with delimeter bit set, thus braking record
bounds.
Also remove ignore of non-stream type of packets, handle SEQPACKET
feature bit.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To make transport work with SOCK_SEQPACKET add two things:
1) SOCK_SEQPACKET ops for virtio transport and 'seqpacket_allow()'
   callback.
2) Handling of SEQPACKET bit: guest tries to negotiate it with vhost,
   so feature will be enabled only if bit is negotiated with device.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Small updates to make SOCK_SEQPACKET work:
1) Send SHUTDOWN on socket close for SEQPACKET type.
2) Set SEQPACKET packet type during send.
3) Set 'VIRTIO_VSOCK_SEQ_EOR' bit in flags for last
   packet of message.
4) Implement data check function for SEQPACKET.
5) Check for max datagram size.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update current receive logic for SEQPACKET support: performs
check for packet and socket types on receive(if mismatch, then
reset connection). Increment EOR counter on receive. Also if
buffer of new packet was appended to buffer of last packet in
rx queue, update flags of last packet with flags of new packet.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Callback fetches RW packets from rx queue of socket until whole record
is copied(if user's buffer is full, user is not woken up). This is done
to not stall sender, because if we wake up user and it leaves syscall,
nobody will send credit update for rest of record, and sender will wait
for next enter of read syscall at receiver's side. So if user buffer is
full, we just send credit update and drop data.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add set of defines and constants for SOCK_SEQPACKET support
in vsock.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is static and 'hdr' arg was always NULL.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to set type of packet which differs from type
of socket, so move passing type of packet from 'info' structure
to  'virtio_transport_send_pkt_info()' function. Since at current
time only stream type is supported, set it directly in 'virtio_
transport_send_pkt_info()', so callers don't need to set it.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace 'stream' to 'connection oriented' in comments as
SEQPACKET is also connection oriented.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add socket ops for SEQPACKET type and .seqpacket_allow() callback
to query transports if they support SEQPACKET. Also split path
for data check for STREAM and SEQPACKET branches.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update current stream enqueue function for SEQPACKET
support:
1) Call transport's seqpacket enqueue callback.
2) Return value from enqueue function is whole record length or error
   for SOCK_SEQPACKET.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add receive loop for SEQPACKET. It looks like receive loop for
STREAM, but there are differences:
1) It doesn't call notify callbacks.
2) It doesn't care about 'SO_SNDLOWAT' and 'SO_RCVLOWAT' values, because
   there is no sense for these values in SEQPACKET case.
3) It waits until whole record is received.
4) It processes and sets 'MSG_TRUNC' flag.

So to avoid extra conditions for two types of socket inside one loop, two
independent functions were created.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some code in receive data loop could be shared between SEQPACKET
and STREAM sockets, while another part is type specific, so move STREAM
specific data receive logic to '__vsock_stream_recvmsg()' dedicated
function, while checks, that will be same for both STREAM and SEQPACKET
sockets, stays in 'vsock_connectible_recvmsg()'.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wait loop for data could be shared between SEQPACKET and STREAM
sockets, so move it to dedicated function. While moving the code
around, let's update an old comment.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepare af_vsock.c for SEQPACKET support: rename some functions such
as setsockopt(), getsockopt(), connect(), recvmsg(), sendmsg() in general
manner, because they are shared with stream sockets.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Naveen Mamindlapalli says:

====================
octeontx2: Add trusted VF support

This series adds support for trusted VF. The trusted VF support
allows VFs to perform priviliged operations such as setting VF
interface in promiscuous mode, all-multicast mode and also
changing the VF MAC address even if it was asssigned by PF.

Patches #1 and #2 provides the necessary functionality for supporting
promiscuous and multicast packets on both the PF and VF.

Patches #3 and #4 enable trusted VF configuration support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for setting a VF as a trusted VF by PF admin. Trusted VF
feature allows VFs to perform priviliged operations such as enabling
VF promiscuous mode, all-multicast mode and changing the VF MAC address
even if it was assigned by PF.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>