If a command cannot be sent or there is a internal error an errno maybe
set instead of a command status.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds bt_status which can be used to convert Unix errno to
Bluetooth status.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This splits hci_dev_open_sync so each stage is handle by its own
function so it is easier to identify each stage.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Make use of hci_cmd_sync_queue for removing an advertisement monitor.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Make use of hci_cmd_sync_queue for adding an advertisement monitor.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk for fake CSR controllers.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk for QCA controllers.

The reason why these two HCI commands are broken for QCA controllers is
that feature "Erroneous Data Reporting" is not enabled by their firmware
as shown by below log:

@ RAW Open: hcitool (privileged) version 2.22
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Complete (0x0e) plen 68
  Read Local Supported Commands (0x04|0x0002) ncmd 1
    Status: Success (0x00)
    Commands: 288 entries
......
      Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
      Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
......

< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
> HCI Event: Command Complete (0x0e) plen 4
  Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
    Status: Unknown HCI Command (0x01)

< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 12
  Read Local Supported Features (0x04|0x0003) ncmd 1
    Status: Success (0x00)
    Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87
      3 slot packets
......
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

BT core driver should addtionally check LMP feature bit
"Erroneous Data Reporting" instead of quirk
HCI_QUIRK_BROKEN_ERR_DATA_REPORTING set by BT device driver to decide if
HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken.

BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 2, Part C | page 587
This feature indicates whether the device is able to support the
Packet_Status_Flag and the HCI commands HCI_Write_Default_-
Erroneous_Data_Reporting and HCI_Read_Default_Erroneous_-
Data_Reporting.

the quirk was introduced by 'commit cde1a8a9 ("Bluetooth: btusb: Fix
and detect most of the Chinese Bluetooth controllers")' to mark HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting broken by BT
device driver, but the reason why these two HCI commands are broken is
that feature "Erroneous Data Reporting" is not enabled by firmware, this
scenario is illustrated by below log of QCA controllers with USB I/F:

@ RAW Open: hcitool (privileged) version 2.22
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Complete (0x0e) plen 68
      Read Local Supported Commands (0x04|0x0002) ncmd 1
        Status: Success (0x00)
        Commands: 288 entries
......
          Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
          Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
......

< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
> HCI Event: Command Complete (0x0e) plen 4
      Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
        Status: Unknown HCI Command (0x01)

< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 12
      Read Local Supported Features (0x04|0x0003) ncmd 1
        Status: Success (0x00)
        Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87
          3 slot packets
......
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Event HCI_Truncated_Page_Complete should belong to central
and HCI_Peripheral_Page_Response_Timeout should belong to
peripheral, but hci_set_event_mask_page_2_sync() take these
two events for wrong roles, so correct it by this change.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add VID/PID 0489:e0e2 for MediaTek MT7922 Bluetooth chip. Found and
tested with Asus UM5302TA.

From /sys/kernel/debug/usb/devices:

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0e2 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: He Wang <xw897002528@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for MTK controllers
since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=215576Signed-off-by: Yuri D'Elia <wavexx@thregr.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add device specific data for max baudrate in autobaud mode. This allows the
host to use a baudrate higher than "init speed" when loading FW in autobaud
mode.

The device specific max baudrate in autobaud mode for CYW55572 is set to
921600 bps. Devices without device specific max baudrate in autobaud mode
will use init speed as before. If no device specific init speed has been
specified, it will default to the bcm_proto default 115200 bps.

The increased baud rate improves FW load time. The exact load time will
depend on the specific system and FW being used. As a rough indication,
the FW load time dropped from ~9s @ 115.2kbps to ~1.7s @ 921.6kbps in one
test.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Always prevent trying to set device baudrate before calling setup() when
using autobaud mode.

This was previously happening for devices which had device specific data
with member no_early_set_baudrate set to 0.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add conditional constraint to make property "reset-gpios" available only
for compatible devices acually having the reset pin.

Make property "brcm,requires-autobaud-mode" depend on property
"shutdown-gpios" as the shutdown pin is required to enter autobaud mode.

I looked at all compatible devices and compiled the matrix below before
formulating the conditional constraint. This was a pure paper exercise and
no verification testing has been performed.

                                d
                                e
                                v h
                                i o
                                c s
                            s   e t
                            h   - -
                            u   w w       v
                            t r a a     v d
                            d e k k     b d
                            o s e e     a i
                            w e u u     t o
                            n t p p     - -
                            - - - -     s s
                            g g g g     u u
                            p p p p t   p p
                            i i i i x l p p
                            o o o o c p l l
                            s s s s o o y y
    ---------------------------------------
    brcm,bcm20702a1         X X X X X X X X
    brcm,bcm4329-bt         X X X X X X X X
    brcm,bcm4330-bt         X X X X X X X X
    brcm,bcm4334-bt         X - X X X X X X
    brcm,bcm43438-bt        X - X X X X X X
    brcm,bcm4345c5          X - X X X X X X
    brcm,bcm43540-bt        X - X X X X X X
    brcm,bcm4335a0          X - X X X X X X
    brcm,bcm4349-bt         X - X X X X X X
    infineon,cyw55572-bt    X - X X X X X X
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon.
Extend the binding with its DT compatible.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The bt_skb_sendmsg() function can't return NULL so there is no need to
check for that.  Several of these checks were removed previously but
this one was missed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the support ID(0x13D3, 0x3586) to usb_device_id table for
Realtek RTL8852C.

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3586 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the support ID(0x13D3, 0x3587) to usb_device_id table for
Realtek RTL8852C.

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3587 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the support ID(0x0CB8, 0xC558) to usb_device_id table for
Realtek RTL8852C.

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cb8 ProdID=c558 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the support ID(0x04c5, 0x1675) to usb_device_id table for
Realtek RTL8852C.

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04c5 ProdID=1675 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the support ID(0x04CA, 0x4007) to usb_device_id table for
Realtek RTL8852C.

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=4007 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth HCI devices indicate if they are able to wakeup in the wakeup
callback since 'commit 4539ca67 ("Bluetooth: Rename driver
.prevent_wake to .wakeup")'. This patch adds a default wakeup callback
for Bluetooth HCI UAR devices. It assumes Bluetooth HCI UART devices are
wakeable for backward compatibility. For those who need a customized
behavior, one can override it before calling hci_uart_register_device().

Fixes: 4539ca67 ("Bluetooth: Rename driver .prevent_wake to .wakeup")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

These devices are likely going to be reprogrammed when disconnected so
this avoid a whole bunch of commands attempt to remove and the add back
to the list.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Zhengping Jiang <jiangzp@google.com>

When programming a new entry into the resolving list it shall default
to network mode since the params may contain the mode programmed when
the device was last added to the resolving list.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=209745
Fixes: 853b70b5 ("Bluetooth: hci_sync: Set Privacy Mode when updating the resolving list")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Zhengping Jiang <jiangzp@google.com>

Annotate hci_rx_work() with kcov_remote_start() and kcov_remote_stop()
calls, so remote KCOV coverage is collected while processing the rx_q
queue which is the main incoming Bluetooth packet queue.

Coverage is associated with the thread which created the packet skb.

The collected extra coverage helps kernel fuzzing efforts in finding
vulnerabilities.

This change only has effect if the kernel is compiled with CONFIG_KCOV,
otherwise kcov_ functions don't do anything.
Signed-off-by: Tamas Koczka <poprdi@google.com>
Tested-by: Aleksandr Nogikh <nogikh@google.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

After resuming, remove setting scanning_paused to false, because it is
checked and set to false in hci_resume_scan_sync. Also move setting
the value to false before updating passive scan, because the value is
used when resuming passive scan.

Fixes: 3b420553 (Bluetooth: hci_sync: Fix attempting to suspend with
unfiltered passive scan)
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Commit ce64b3e9 ("Bluetooth: mt7921s: Support wake on bluetooth")
adds the wake on bluethooth via a dedicated GPIO.

Extend the wake-on-bluetooth to use the SDIO DAT1 pin (in-band wakeup),
when supported by the SDIO host driver.
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Set the connection data before calling get_conn_info_sync, so it can be
verified the connection is still connected, before refreshing cached
values.

Fixes: 47db6b42 ("Bluetooth: hci_sync: Convert MGMT_OP_GET_CONN_INFO")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The scan response and advertising data needs to be tracked on a per
instance (adv_info) since when these instaces are removed so are their
data, to fix that new flags are introduced which is used to mark when
the data changes and then checked to confirm when the data needs to be
synced with the controller.
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Both dev_name and short_name are not guaranteed to be NULL terminated so
this instead use strnlen and then attempt to determine if the resulting
string needs to be truncated or not.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=216018Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Similar to the handling of l2cap_ecred_connect in commit d3715b23
("Bluetooth: use memset avoid memory leaks"), we thought a patch
might be needed here as well.

Use memset to initialize structs to prevent memory leaks
in l2cap_le_connect
Signed-off-by: Xiaohui Zhang <xiaohuizhang@ruc.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Preserve the error code from hci_register_suspend_notifier().  Don't
return success.

Fixes: d6bb2a91f95b ("Bluetooth: Unregister suspend with userchannel")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth
portion can be controlled over serial.

Two subversions are added for the chip, because ROM firmware reports
002.002.013 (at least for the chips I have here), while depending on
patchram firmware revision, either 002.002.013 or 002.002.014 is
reported.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth
portion can be controlled over serial.
Extend the binding with its DT compatible.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When HCI_USERCHANNEL is used, unregister the suspend notifier when
binding and register when releasing. The userchannel socket should be
left alone after open is completed.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When a userchannel socket is released, we should check whether the hdev
is already unregistered before sending out an IndexAdded.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The HCI command, event, and data packet processing workqueue is drained
to avoid deadlock in commit
76727c02 ("Bluetooth: Call drain_workqueue() before resetting state").

There is another delayed work, which will queue command to this drained
workqueue. Which results in the following error report:

Bluetooth: hci2: command 0x040f tx timeout
WARNING: CPU: 1 PID: 18374 at kernel/workqueue.c:1438 __queue_work+0xdad/0x1140
Workqueue: events hci_cmd_timeout
RIP: 0010:__queue_work+0xdad/0x1140
RSP: 0000:ffffc90002cffc60 EFLAGS: 00010093
RAX: 0000000000000000 RBX: ffff8880b9d3ec00 RCX: 0000000000000000
RDX: ffff888024ba0000 RSI: ffffffff814e048d RDI: ffff8880b9d3ec08
RBP: 0000000000000008 R08: 0000000000000000 R09: 00000000b9d39700
R10: ffffffff814f73c6 R11: 0000000000000000 R12: ffff88807cce4c60
R13: 0000000000000000 R14: ffff8880796d8800 R15: ffff8880796d8800
FS:  0000000000000000(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000c0174b4000 CR3: 000000007cae9000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 ? queue_work_on+0xcb/0x110
 ? lockdep_hardirqs_off+0x90/0xd0
 queue_work_on+0xee/0x110
 process_one_work+0x996/0x1610
 ? pwq_dec_nr_in_flight+0x2a0/0x2a0
 ? rwlock_bug.part.0+0x90/0x90
 ? _raw_spin_lock_irq+0x41/0x50
 worker_thread+0x665/0x1080
 ? process_one_work+0x1610/0x1610
 kthread+0x2e9/0x3a0
 ? kthread_complete_and_exit+0x40/0x40
 ret_from_fork+0x1f/0x30
 </TASK>

To fix this, we can add a new HCI_DRAIN_WQ flag, and don't queue the
timeout workqueue while command workqueue is draining.

Fixes: 76727c02 ("Bluetooth: Call drain_workqueue() before resetting state")
Reported-by: syzbot+63bed493aebbf6872647@syzkaller.appspotmail.com
Signed-off-by: Schspa Shi <schspa@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.

Fixes: 1ab1f239 ("Bluetooth: hci_intel: Add support for platform driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>