- 27 Jul, 2010 40 commits
-
-
James Bottomley authored
we also need to clean up and free the cdev. Reported-by:
Jani Nikula <ext-jani.1.nikula@nokia.com> Cc: Stable Tree <stable@kernel.org> Signed-off-by:
James Bottomley <James.Bottomley@suse.de>
-
Brian King authored
Bump driver version Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Brian King authored
If we encounter an error when sending a management datagram (i.e. non SCSI command, such as virtual adapter initialization command), we end up incrementing the request_limit, even though we don't decrement it for these commands. Fix this up by doing this increment in the error path for SRP commands only. Signed-off-by:
-
Brian King authored
Fixes a deadlock that can occur if we hit a command timeout during the virtual adapter initialization. The event done functions are written with the assumption that no locks are held, however, when purging requests this is not true. Fix up the purge function to drop the lock so that the done function is not called with the lock held, which can cause a deadlock. Signed-off-by:
-
Brian King authored
This fixes a softlockup seen on resume. During resume, the CRQ must be reenabled. However, the H_ENABLE_CRQ hcall used to do this may return H_BUSY or H_LONG_BUSY. When this happens, the caller is expected to retry later. This patch changes a simple loop, which was causing the softlockup, to a loop at task level which sleeps between retries rather than simply spinning. Signed-off-by:
-
Brian King authored
Bump driver version. Signed-off-by:
-
Brian King authored
Adds support for fc_block_scsi_eh to block the EH handlers if the target device is in the blocked state to ensure we don't take devices offline. Signed-off-by:
-
Brian King authored
This fixes a softlockup seen on resume. During resume, the CRQ must be reenabled. However, the H_ENABLE_CRQ hcall used to do this may return H_BUSY or H_LONG_BUSY. When this happens, the caller is expected to retry later. Normally the H_ENABLE_CRQ succeeds relatively soon. However, we have seen cases where this can take long enough to see softlockup warnings. This patch changes a simple loop, which was causing the softlockup, to a loop at task level which sleeps between retries rather than simply spinning. Signed-off-by:
-
Bandan Das authored
In mpt_detach, call to pci_set_drvdata is redundant because it has already been called in mpt_adapter_disable. In mpt_attach, ioc->pcidev is set to pdev two times. Signed-off-by:
Bandan Das <bandan.das@stratus.com> Acked-by:
"Desai, Kashyap" <Kashyap.Desai@lsi.com> Signed-off-by:
-
Kashyap, Desai authored
Upgrade driver version to 3.4.16 Signed-off-by:
-
Kashyap, Desai authored
Added missing part which will reset ioc_reset_in_progress before returning from SoftResetHandler. Signed-off-by:
-
Kashyap, Desai authored
Issue: SATA hotplug does not work sometimes. At the time of ADD device/ADD phys disk, drive may fail to add SATA device due to temporary SAS Address for SATA device generated by firmware. Final SAS address for SATA driver will be generated only after disk spinup is done. This may take some times for slow spining SATA drives. At phy link up driver gets attached device sas address and stores into phyinfo. At the time of ADD event driver will read sas device page0 using channel and FW ID provided in ADD Device event. Here in case of SATA drives, driver will see miss match in phyinfo->sas_address and latest sas address read from SAS DEVICE PAGE0 and eventually device won't be added to OS. Fix: When Driver read SAS DEVICE PAGE0, it can identify Device type looking at device_info. If device is SATA drive and sas address mismatch happens, Driver will do same stuffs which happened at the time of LINK UP to get correct piece of information from Pages. ( Find parent device and refresh parent device phys either HBA refresh/Exp refresh) Signed-off-by:
-
Kashyap, Desai authored
Issue: target reset will be queued to driver's internal queue to get schedule later. When driver add target into internal target_reset queue we will block IOs on those target using scsi midlayer API. Now due to some cause driver is not executing those target_reset list and it is always in block state. Changes: now we are clearing target_reset queue from all other Callback context instead of only DeviceReset context.Now wherever driver is clearing taskmgmt_in_progress flag it is considering target_reset queue cleanup also. Signed-off-by:
-
Kashyap, Desai authored
Added sanity check before treating any device is a valid device. It is possible that firmware can have device page0 in its table, but that devicemay not be available in topology. Device will be available in topology only if there is Bus Target mapping is done in firmware. Driver will always check B_T mapping of firmware before reporting device to upper layer. Signed-off-by:
-
Kashyap, Desai authored
device missing delay is 8 bit value in io unit pg1. Making correct variable declaration for device_missing_delay. The driver is storing the calculated device missing delay in IOC structure as a u8 instead of a u16. It needs to be a u16 if the delay is > 255. Signed-off-by:
-
Kashyap, Desai authored
Changed the return value for Nexus Loss IOs to be DID_TRANSPORT_DISRUPTED. What this will allow is the multi-path driver to delay the fail over process. They would like the path to keep up as long as the nexus loss Loginfo is return from firmware. With DID_BUS_BUSY the path fails over immediately. Signed-off-by:
-
Kashyap, Desai authored
fw_events_off is flag checking for driver to do Event handling or not. Normally it should be OFF at the time of initialization. Only enable it at the time of INTR enable of device first time. This will always occur only after resource allocation. ioc->fw_events_off = 1 is set in mpt_attach() Signed-off-by:
-
Kashyap, Desai authored
Version upgrade patch Signed-off-by:
-
Kashyap, Desai authored
Current driver is not clearing the per device tm_busy flag following the Task Mangement request completion from the IOCTL path. When this flag is set, the IO queues are frozen. The reason the flag didn't get cleared is becuase the driver is referencing memory associated to the mpi request following the completion, when the memory had been reallocated for a new request. When the memory was reallocated, the driver didn't clear the flag becuase it was expecting a task managment reqeust, and the reallocated request was for SCSI_IO. To fix the problem the driver needs to have a cached backup copy of the original reqeust. Signed-off-by:
-
Kashyap, Desai authored
(1) driver was not setting the sense data size prior to sending SCSI_IO, resulting in the 0x31190000 loginfo (2) The driver needs to copy the sense data to local buffer prior to releasing the request message frame. If not, the sense buffer gets overwritten by the next SCSI_IO request. Signed-off-by:
-
Kashyap, Desai authored
Adding additional messages to the error escallation callbacks which displays the wwid, sas address, handle, phy number, enclosure logical id, and slot. In the same eh callbacks, routines, the printks were converted to sdev_printks, which displays the bus target mapping. These additional modifications help better identify the device which is in recovery. Signed-off-by:
-
Kashyap, Desai authored
ISSUE DESCRIPTION: This test case involves creating two RAID1 volumes, then simultaneiously issue host reset and pull all the drives associated to the 1st raid volume. The observed behavour is the physical drives are removed, however the volume remains. The expected behavour is the volume as well as physical drives should be removed from OS. FIX: Add support in the post host reset device scan logic for raid volumes where the driver will have an additional check for responding raid volume where the status should be either online, optimal, or degraded. So for voluemes that have a status of missing or failed, the driver will mark them for deletion. Signed-off-by:
-
Kashyap, Desai authored
In the driver mpt2sas_base_attach subroutine, we need to add support to return the proper error code when there are memory allocation failures, e.g. returning -ENOMEM. Signed-off-by:
-
Kashyap, Desai authored
Actual problem : Driver may receiving the top level expander removal event prior to all the individual PD removal events, hence the driver is breaking down all the PDs in advanced to the actaul PD UNHIDE event. Driver sends multiple Target Resets to the same volume handle for each individual PD removal. FIX DESCRIPTION: To fix this issue, the entire PD device handshake protocal has to be moved to interrupt context so the breakdown occurs immediately after the actual UNHIDE event arrives. The driver will only issue one Target Reset to the volume handle, occurring after the FAILED or MISSING volume status event arrives from interrupt context. For the PD UNHIDE event, the driver will issue target resets to the PD handles, followed by OP_REMOVE. The driver will set the "deteleted" flag during interrupt context. A "pd_handle" bitmask was introduced so the driver has a list of known pds during entire life of the PD; this replaces the "hidden_raid_component" flag handle in the sas_device object. Each bit in the bitmask represents a device handle. The bit in the bitmask would be toggled ON/OFF when the HIDE/UNHIDE events arrive; also this pd_handle bitmask would bould be refreshed across host resets. Here we kept older behavior of sending target reset to volume when there is a single drive pull, wait for the reply, then send target resets to the PDs. We kept this behavior so the driver will behave the same for older versions of firmware. Signed-off-by:
-
Kashyap, Desai authored
Add support to display additional debug info for SCSI_IO and RAID_SCSI_IO_PASSTHROUGH sent from the normal entry queued entry point, as well as internal generated commands, and IOCTLS. The additional debug info included the phy number, as well as the sas address, enclosure logical id, and slot number. This debug info has to be enabled thru the logging_level command line option, by default this will not be displayed. Signed-off-by:
-
Kashyap, Desai authored
Converting print level from MPT2SAS_DEBUG_FMT to MPT2SAS_INFO_FMT. Signed-off-by:
-
Kashyap, Desai authored
Added support so the diag ring buffer can be pulled via sysfs Added three new shost attributes: host_trace_buffer, host_trace_buffer_enable, and host_trace_buffer_size. The host_trace_buffer_enable attribute is used to either post or release the trace buffers. The host_trace_buffer_size attribute contains the size of the trace buffer. The host_trace_buffer atttribute contains a maximum 4KB window of the buffer. In order to read the entire host buffer, you will need to write the offset to host_trace_buffer prior to reading it. release the host buffer, then write the entire host buffer contents to a file. In addition to this enhancement, we moved the automatic posting of host buffers at driver load time to be called prior to port_enable, instead of after. That way discovery is available in the host buffer. Signed-off-by:
-
Kashyap, Desai authored
Updating MPI header version N. Removed mpi_history.txt. Signed-off-by:
-
Kashyap, Desai authored
Added a new sysfs shost attribute called ioc_reset_count. This will keep count of host resets (both diagnostic and message unit). Signed-off-by:
-
Kashyap, Desai authored
Added support to send link resets, hard resets, enable/disable phys, and changing link rates for for expanders. This will be exported to attributes within the sas transport layer. A new wrapper function was added for sending SMP passthru to expanders for phy control. Signed-off-by:
-
Kashyap, Desai authored
Added support to retrieve the invalid_dword_count, running_disparity_error_count, loss_of_dword_sync_count, and phy_reset_problem_count for expanders. This will be exported to attributes within the sas transport layer. A new wrapper function was added for sending SMP passthru to retrieve the expander phy error log. Signed-off-by:
-
Kashyap, Desai authored
Added command line option called disable_discovery. When enabled on the command line, the driver will not send a port_enable when loaded for the first time. If port_enable is not called, then there is no discovery of devices, as well as the sas topology. Then later if one desires to invoke discovery, then they will need to issue a diagnostic reset. A diagnostic reset can be issued various ways. One of the way is throught sysfs. Signed-off-by:
-
Kashyap, Desai authored
Driver should not allow multiple host reset when already host reset is in progress. It is possible that host reset was sent by scsi mid layer while there was already an host reset active, either issued via IOCTL interface or internaly, like a config page timeout. Since there was a host reset active, the driver would return a FAILED response to the scsi mid layer. The solution is make sure pending host resets will wait for the active host reset to complete before returning control back up the call stack. Signed-off-by:
-
Kashyap, Desai authored
[SCSI] mpt2sas: Fix to use sas device list instead of enclosure list for _transpor_get_enclosure_identifier. Enclosure_identifier not being returned by mpt2sas The driver exports callback function to the sas transport layer for obtaining the enclosure logical id. This function is called _transport_get_enclosure_identifier. The driver was searching the wrong list for the enclosure_identifier. The driver should be searching the sas device list instead of enclosure list. The sas address that is passed to the driver is for the end device, not enclosure. Signed-off-by:
-
Karen Xie authored
Zero out the reserved or un-used CPL message fields to prevent any garbage value. Signed-off-by:
Karen Xie <kxie@chelsio.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Stephen M. Cameron authored
Some controllers might try to tell us they support 0 commands in performant mode. This is a lie told by buggy firmware. We have to be wary of this lest we try to allocate a negative number of command blocks, which will be treated as unsigned, and get an out of memory condition. Signed-off-by:
Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by:
-
Stephen M. Cameron authored
There are things which need to be done in the intx interrupt handler which do not need to be done in the msi/msix interrupt handler, like checking that the interrupt is actually for us, and checking that the interrupt pending bit on the hardware is set (which we weren't previously doing at all, which means old controllers wouldn't work), so it makes sense to separate these into two functions. Signed-off-by:
-
Stephen M. Cameron authored
The 6402/6404 are two PCI devices -- two Smart Array controllers -- that fit into one slot. It is possible to reset them independently, however, they share a battery backed cache module. One of the pair controls the cache and the 2nd one access the cache through the first one. If you reset the one controlling the cache, the other one will not be a happy camper. So we just forbid resetting this conjoined mess. Signed-off-by:
-
Stephen M. Cameron authored
Smart Array controllers newer than the P600 do not honor the PCI power state method of resetting the controllers. Instead, in these cases we can get them to reset via the "doorbell" register. This escaped notice until we began using "performant" mode because the fact that the controllers did not reset did not normally impede subsequent operation, and so things generally appeared to "work". Once the performant mode code was added, if the controller does not reset, it remains in performant mode. The code immediately after the reset presumes the controller is in "simple" mode (which previously, it had remained in simple mode the whole time). If the controller remains in performant mode any code which presumes it is in simple mode will not work. So the reset needs to be fixed. Unfortunately there are some controllers which cannot be reset by either method. (eg. p800). We detect these cases by noticing that the controller seems to remain in performant mode even after a reset has been attempted. In those case, we proceed anyway, as if the reset has happened (and skip the step of waiting for the controller to become ready -- which is expecting it to be in "simple" mode.) To sum up, we try to do a better job of resetting the controller if "reset_devices" is set, and if it doesn't work, we print a message and try to continue anyway. Signed-off-by:
-
Stephen M. Cameron authored
for kdump support Signed-off-by:
-
