- 17 Mar, 2022 16 commits
-
-
https://github.com/nbd168/wirelessKalle Valo authored
mt76 patches for 5.18 - bugfixes - mbssid support for mt7915 - 6 GHz support for mt7915 - mt7921u driver
-
Ping-Ke Shih authored
These function is used to stop transmitting when we are going to switch channels or do some RF calibration. Before these operations, we need to stop channel transmission and backup setting into parameter tx_en. After operations are done, resume transmitting by backup parameter tx_en. Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220317055543.40514-13-pkshih@realtek.com
-
Ping-Ke Shih authored
In order to support 8852C that uses 32 bits to control TX types. This patch doesn't really use 32 bits tx_en yet, but next patch will use it. Signed-off-by:
-
Ping-Ke Shih authored
Use if() style would be clear than "? :", because the else cases are always 0. The read val from rtw89_mac_read_lte() isn't used, so remove this statement. Signed-off-by:
-
Chia-Yuan Li authored
The BT-coexistence uses these function to control antenna and TDMA, so implement the variant type to support all chips. Signed-off-by:
Chia-Yuan Li <leo.li@realtek.com> Signed-off-by:
-
Chia-Yuan Li authored
Initialize FW status and disabled H2C function if CPU disabled. Then, it can reset to initial state. Signed-off-by:
-
Ping-Ke Shih authored
8852C add new hardware feature -- preload window, which is used to load more data to D-MAC, so it can possibly yield better performance. This patch is to configure preload and reserved size for next window. Signed-off-by:
-
Chia-Yuan Li authored
Modify functions that control D-MAC (data MAC) and LDO to support variant chips. Signed-off-by:
-
Ping-Ke Shih authored
The format of RF parameter is changed; it doesn't encode delay parameters into table, but the delay coding becomes regular pair of register address and value. To help firmware to recover RF register settings, we need to download these parameters to firmware. For v1 format, only download partial parameters (ignore them with addr < 0x100). Signed-off-by:
-
Chung-Hsuan Hung authored
Using encoded address which BIT(16) is used to discriminate which region is going to access. Illustrate the calling flow as below rtw89_phy_write_rf_v1() -+-> rtw89_phy_write_rf() // old interface +-> rtw89_phy_write_rf_a() // new interface Signed-off-by:Chung-Hsuan Hung <hsuan8331@realtek.com> Signed-off-by:
-
Yuan-Han Zhang authored
Configure this TX power to indicate TX power offset that uses to transmit TB (trigger base) uplink frames. Also, shrink the unit of TX power offset changes to suitable type s8. Signed-off-by:
Yuan-Han Zhang <yuanhan1020@realtek.com> Signed-off-by:
-
Yuan-Han Zhang authored
The CFO tracking algorithm is the same, but control methods are different. Set parameters via xtal serial interfaces (SI). Signed-off-by:
-
Yuan-Han Zhang authored
The dcfo_comp is digital CFO (central frequency offset) compensation. Since the flow can be shared with all chips, add chip parameters to support variant register address and format. Signed-off-by:
-
Colin Ian King authored
There are some spelling mistakes in some literal strings. Fix them. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Acked-by:
-
Colin Ian King authored
There are some spelling mistakes in comments and brcmf_dbg messages. Fix these. Signed-off-by:
-
Arnd Bergmann authored
Building iwlmei without CONFIG_CFG80211 causes a link-time warning: ld.lld: error: undefined symbol: ieee80211_hdrlen >>> referenced by net.c >>> net/wireless/intel/iwlwifi/mei/net.o:(iwl_mei_tx_copy_to_csme) in archive drivers/built-in.a Add an explicit dependency to avoid this. In theory it should not be needed here, but it also seems pointless to allow IWLMEI for configurations without CFG80211. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Emmanuel Grumbach <Emmanuel.grumbach@intel.com> Acked-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
-
- 16 Mar, 2022 24 commits
-
-
Deren Wu authored
When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to fw for channel config. This would cause rx performance bad while monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would get the same performance as normal channels. Reviewed-by:
Shayne Chen <shayne.chen@mediatek.com> Signed-off-by:
Deren Wu <deren.wu@mediatek.com> Signed-off-by:
Felix Fietkau <nbd@nbd.name>
-
Sean Wang authored
IEEE80211_CONF_CHANGE_MONITOR would be set every time even when vif runs as sta mode. If vif runs as sta mode, the beacon filter would be falsely enabled earlier than the associated state. That is not the behavior the firmware expects and also breaks the original logic of sta mode. Thus, we only limit the operation to set the beacon filter only for monitor mode when IEEE80211_CONF_CHANGE_MONITOR is set. Fixes: 4ad65a54 ("mt76: mt7921: toggle runtime-pm adding a monitor vif") Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
-
Deren Wu authored
Due to the missing IEEE80211_RADIOTAP_HE_DATA1_BW_RU_ALLOC_KNOWN in status report, the HE rate in wirehsark/tcpdump always shows wrong value. Applications will refer to IEEE80211_RADIOTAP_HE_DATA5_DATA_BW_RU_ALLOC when the flag is set and shows the correct data rate. Reviewed-by:
Ryder Lee <ryder.lee@mediatek.com> Signed-off-by:
-
Lorenzo Bianconi authored
Introduce mbss mcu APIs to enable 802.11ax multi-bss AP support for mt7915 devices Tested-by:
Money Wang <money.wang@mediatek.com> Co-developed-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Lorenzo Bianconi authored
Firmware initialization can take a while. Move mt7921_init_hw routine in a dedicated work in order to not slow down bootstrap process. Tested-by:
-
Lorenzo Bianconi authored
Introduce support for MT7921U 802.11ax 2x2:2SS wireless devices. Tested-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to add mt7921u driver support. Tested-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to add mt7921u driver support. Tested-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to add mt7921u driver support. Tested-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to add mt7921u driver support. Tested-by:
-
Lorenzo Bianconi authored
Runtime-pm is not currently supported by usb driver Tested-by:
-
Lorenzo Bianconi authored
Introduce __mt76u_init unitility routine and move mt7615 usb bus ops into mt7615 module in order to allow specifying driver specific parameter. This is a preliminary patch to add usb support to mt7921 driver. Tested-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to add usb support to mt7921 driver. Tested-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to add usb support to mt7921 driver. Tested-by:
-
Julia Lawall authored
Various spelling mistakes in comments. Detected with the help of Coccinelle. Signed-off-by:
Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by:
-
Peter Chiu authored
This patch fixes performance issue of beamforming tx on bandwidth 160MHz. Fixes: 99ad32a4 ("mt76: mt7915: add support for MT7986") Signed-off-by:
Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by:
-
Shayne Chen authored
Some of beamforming mib counters are moved to different offsets or registers in newer chipsets. Fixes: 99ad32a4 ("mt76: mt7915: add support for MT7986") Signed-off-by:
-
Shayne Chen authored
Set proper group index of tx descriptor for band1. Signed-off-by:
-
Deren Wu authored
Drop invalid rssi value to calculate a reasonable report Fixes: 4550fb9e ("mt76: improve signal strength reporting") Signed-off-by:
-
Ryder Lee authored
Switch to use le32/16_get_bits() to simplfy codes and specify the size explicitly to avoid potential issues. Signed-off-by:
-
Colin Ian King authored
Don't populate the read-only array ba_range on the stack but instead make it static const. Also makes the object code a little smaller. Signed-off-by:
-
Dan Carpenter authored
If devm_pinctrl_get() fails then it leads to an error pointer dereference. Add a check to prevent that. Fixes: 99ad32a4 ("mt76: mt7915: add support for MT7986") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Lorenzo Bianconi authored
mt7921_wait_for_mcu_init is no longer used. Signed-off-by:
-
Shayne Chen authored
Add support to init txpower values of 6GHz band. Signed-off-by:
MeiChia Chiu <MeiChia.Chiu@mediatek.com> Signed-off-by:
-
