- 15 Jun, 2010 29 commits
-
-
Eric Dumazet authored
inetpeer currently uses an AVL tree protected by an rwlock. It's possible to make most lookups use RCU 1) Add a struct rcu_head to struct inet_peer 2) add a lookup_rcu_bh() helper to perform lockless and opportunistic lookup. This is a normal function, not a macro like lookup(). 3) Add a limit to number of links followed by lookup_rcu_bh(). This is needed in case we fall in a loop. 4) add an smp_wmb() in link_to_pool() right before node insert. 5) make unlink_from_pool() use atomic_cmpxchg() to make sure it can take last reference to an inet_peer, since lockless readers could increase refcount, even while we hold peers.lock. 6) Delay struct inet_peer freeing after rcu grace period so that lookup_rcu_bh() cannot crash. 7) inet_getpeer() first attempts lockless lookup. Note this lookup can fail even if target is in AVL tree, but a concurrent writer can let tree in a non correct form. If this attemps fails, lock is taken a regular lookup is performed again. 8) convert peers.lock from rwlock to a spinlock 9) Remove SLAB_HWCACHE_ALIGN when peer_cachep is created, because rcu_head adds 16 bytes on 64bit arches, doubling effective size (64 -> 128 bytes) In a future patch, this is probably possible to revert this part, if rcu field is put in an union to share space with rid, ip_id_count, tcp_ts & tcp_ts_stamp. These fields being manipulated only with refcnt > 0. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
Fix the code that handles the error case when cnic_cm_abort() cannot proceed normally. We cannot just set the csk->state and we must go through cnic_ready_to_close() to handle all the conditions. We also add error return code in cnic_cm_abort(). Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Eddie Wai <waie@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
Combine RESET_RECEIVED and RESET_COMP logic and fix race condition between these 2 events and cnic_cm_close(). In particular, we need to (test_and_clear_bit(SK_F_OFFLD_COMPLETE, &csk->flags)) before we update csk->state. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Eddie Wai <waie@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
Move chip-specific code to the respective chip's ->close_conn() functions for better code organization. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Eddie Wai <waie@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
So that bnx2i can handle the error condition immediately and not have to wait for timeout. Signed-off-by: Michael Chan <mchan@broadcom.com. Signed-off-by: Eddie Wai <waie@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
This change corrects issues where macvlan was not correctly triggering promiscuous mode on ixgbe due to the filters not being correctly set. It also corrects the fact that VF rar filters were being overwritten when the PF was reset. CC: Shirley Ma <xma@us.ibm.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Changli Gao authored
unify tcp flag macros: TCPHDR_FIN, TCPHDR_SYN, TCPHDR_RST, TCPHDR_PSH, TCPHDR_ACK, TCPHDR_URG, TCPHDR_ECE and TCPHDR_CWR. TCBCB_FLAG_* are replaced with the corresponding TCPHDR_*. Signed-off-by: Changli Gao <xiaosuo@gmail.com> ---- include/net/tcp.h | 24 ++++++------- net/ipv4/tcp.c | 8 ++-- net/ipv4/tcp_input.c | 2 - net/ipv4/tcp_output.c | 59 ++++++++++++++++----------------- net/netfilter/nf_conntrack_proto_tcp.c | 32 ++++++----------- net/netfilter/xt_TCPMSS.c | 4 -- 6 files changed, 58 insertions(+), 71 deletions(-) Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Register net_bridge_port pointer as rx_handler data pointer. As br_port is removed from struct net_device, another netdev priv_flag is added to indicate the device serves as a bridge port. Also rcuized pointers are now correctly dereferenced in br_fdb.c and in netfilter parts. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Register macvlan_port pointer as rx_handler data pointer. As macvlan_port is removed from struct net_device, another netdev priv_flag is added to indicate the device serves as a macvlan port. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Add possibility to register rx_handler data pointer along with a rx_handler. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Herbert Xu authored
There are multiple problems with the newly added netpoll support: 1) Use-after-free on each netpoll packet. 2) Invoking unsafe code on netpoll/IRQ path. 3) Breaks when netpoll is enabled on the underlying device. This patch fixes all of these problems. In particular, we now allocate proper netpoll structures for each underlying device. We only allow netpoll to be enabled on the bridge when all the devices underneath it support netpoll. Once it is enabled, we do not allow non-netpoll devices to join the bridge (until netpoll is disabled again). This allows us to do away with the npinfo juggling that caused problem number 1. Incidentally this patch fixes number 2 by bypassing unsafe code such as multicast snooping and netfilter. Reported-by: Qianfeng Zhang <frzhang@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Herbert Xu authored
This patch adds the helper netpoll_tx_running for use within ndo_start_xmit. It returns non-zero if ndo_start_xmit is being invoked by netpoll, and zero otherwise. This is currently implemented by simply looking at the hardirq count. This is because for all non-netpoll uses of ndo_start_xmit, IRQs must be enabled while netpoll always disables IRQs before calling ndo_start_xmit. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Herbert Xu authored
This patch adds the functions __netpoll_setup/__netpoll_cleanup which is designed to be called recursively through ndo_netpoll_seutp. They must be called with RTNL held, and the caller must initialise np->dev and ensure that it has a valid reference count. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Herbert Xu authored
This patch adds ndo_netpoll_setup as the initialisation primitive to complement ndo_netpoll_cleanup. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Herbert Xu authored
As it stands, netpoll_setup and netpoll_cleanup have no locking protection whatsoever. So chaos ensures if two entities try to perform them on the same device. This patch adds RTNL to the equation. The code has been rearranged so that bits that do not need RTNL protection are now moved to the top of netpoll_setup. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Herbert Xu authored
The use of RCU in netpoll is incorrect in a number of places: 1) The initial setting is lacking a write barrier. 2) The synchronize_rcu is in the wrong place. 3) Read barriers are missing. 4) Some places are even missing rcu_read_lock. 5) npinfo is zeroed after freeing. This patch fixes those issues. As most users are in BH context, this also converts the RCU usage to the BH variant. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Herbert Xu authored
Now that netpoll always zaps npinfo we no longer need to do it in bridge. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Herbert Xu authored
Since we have to NULL npinfo regardless of whether there is a ndo_netpoll_cleanup, it makes sense to do this unconditionally in netpoll_cleanup rather than having every driver do it by themselves. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Patrick McHardy authored
Conflicts: include/net/netfilter/xt_rateest.h net/bridge/br_netfilter.c net/netfilter/nf_conntrack_core.c Signed-off-by: Patrick McHardy <kaber@trash.net>
-
Luciano Coelho authored
This patch implements an idletimer Xtables target that can be used to identify when interfaces have been idle for a certain period of time. Timers are identified by labels and are created when a rule is set with a new label. The rules also take a timeout value (in seconds) as an option. If more than one rule uses the same timer label, the timer will be restarted whenever any of the rules get a hit. One entry for each timer is created in sysfs. This attribute contains the timer remaining for the timer to expire. The attributes are located under the xt_idletimer class: /sys/class/xt_idletimer/timers/<label> When the timer expires, the target module sends a sysfs notification to the userspace, which can then decide what to do (eg. disconnect to save power). Cc: Timo Teras <timo.teras@iki.fi> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Patrick McHardy <kaber@trash.net>
-
Eric Dumazet authored
- clusterip_lock becomes a spinlock - lockless lookups - kfree() deferred after RCU grace period - rcu_barrier_bh() inserted in clusterip_tg_exit() v2) - As Patrick pointed out, we use atomic_inc_not_zero() in clusterip_config_find_get(). - list_add_rcu() and list_del_rcu() variants are used. - atomic_dec_and_lock() used in clusterip_config_entry_put() Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net>
-
Yaniv Rosner authored
Change 2wire transfer rate of SFP+ module EEPROM from 400Khz to 100Khz since some DACs(direct attached cables) do not work at 400Khz. Reported-by: Krzysztof Oldzki <ole@ans.pl> Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Try to reduce cache line contentions in peer management, to reduce IP defragmentation overhead. - peer_fake_node is marked 'const' to make sure its not modified. (tested with CONFIG_DEBUG_RODATA=y) - Group variables in two structures to reduce number of dirtied cache lines. One named "peers" for avl tree root, its number of entries, and associated lock. (candidate for RCU conversion) - A second one named "unused_peers" for unused list and its lock - Add a !list_empty() test in unlink_from_unused() to avoid taking lock when entry is not unused. - Use atomic_dec_and_lock() in inet_putpeer() to avoid taking lock in some cases. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Uses a seqcount_t to synchronize stat producer and consumer, for packets and bytes counter, now u64 types. (dropped counter being rarely used, stay a native "unsigned long" type) No noticeable performance impact on x86, as it only adds two increments per frame. It might be more expensive on arches where smp_wmb() is not free. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Use RCU to avoid atomic ops on idev refcnt in ipv6_get_mtu() and ip6_dst_hoplimit() Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Use __in6_dev_get() instead of in6_dev_get()/in6_dev_put() Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ben Hutchings authored
commit 97f8aefb "net: fix ethtool coding style errors and warnings" changed the indentation of several macro definitions in ethtool.h. These definitions line up in the diff where there is an extra character at the start of each line, but not in the resulting file. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Conflicts: drivers/net/ixgbe/ixgbe_ethtool.c With merge conflict help from Stephen Rothwell. Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 14 Jun, 2010 9 commits
-
-
Shan Wei authored
The parameter (work) is unused, remove it. Reported from Eric Dumazet. Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net>
-
Shan Wei authored
Instead of doing one atomic operation per frag, we can factorize them. Reported from Eric Dumazet. Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net>
-
Shan Wei authored
If the returned csum value is 0, We has set ip_summed with CHECKSUM_UNNECESSARY flag in __skb_checksum_complete_head(). So this patch kills the check and changes to return to upper caller directly. Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: Patrick McHardy <kaber@trash.net>
-
Eric Dumazet authored
- must use atomic_inc_not_zero() in instance_lookup_get() - must use hlist_add_head_rcu() instead of hlist_add_head() - must use hlist_del_rcu() instead of hlist_del() - Introduce NFULNL_COPY_DISABLED to stop lockless reader from using an instance, before we do final instance_put() on it. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net>
-
Andy Gospodarek authored
This patch added to 2.6.34: commit f8d1dcaf Author: Jesse Brandeburg <jesse.brandeburg@intel.com> Date: Tue Apr 27 01:37:20 2010 +0000 ixgbe: enable extremely low latency introduced a feature where LRO (called RSC on the hardware) was disabled automatically when setting rx-usecs to 0 via ethtool. Some might not like the fact that LRO was disabled automatically, but I'm fine with that. What I don't like is that LRO/RSC is automatically enabled when rx-usecs is set >0 via ethtool. This would certainly be a problem if the device was used for forwarding and it was determined that the low latency wasn't needed after the device was already forwarding. I played around with saving the state of LRO in the driver, but it just didn't seem worthwhile and would require a small change to dev_disable_lro() that I did not like. This patch simply leaves LRO disabled when setting rx-usecs >0 and requires that the user enable it again. An extra informational message will also now appear in the log so users can understand why LRO isn't being enabled as they expect. Inconsistency of LRO setting first noticed by Stanislaw Gruszka. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Stanislaw Gruszka <sgruszka@redhat.com> CC: stable@kernel.org Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Joe Perches authored
commit 675ad473 removed the capability to use ethtool.set_msglevel to control the types of messages emitted by the driver. That commit should probably be reverted. If not, then this patch fixes a message logging defect introduced by converting a printk without KERN_<level> to e_info. This also reduces text by about 200 bytes. Signed-off-by: Joe Perches <joe@perches.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Don Skidmore authored
There is a small window where the watchdog could be running as the interface is brought down on a NIC with two ports wired back to back. If ixgbe_update_status is then called can lead to a panic. This patch allows the update to bail if we are in that condition. This issue was orignally reported and fix proposed by Akihiko Saitou. CC: Akihiko Saitou <asaitou@users.sourceforge.net> Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
No need to copy rxhash again in __skb_clone() Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
John Fastabend authored
deliver_no_wcard is not being set in skb_copy_header. In the skb_cloned case it is not being cleared and may cause the skb to be dropped when the loopback device pushes it back up the stack. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 13 Jun, 2010 2 commits
-
-
Ben Hutchings authored
Device statistics have type unsigned long and several of the device-specific parameters printed here have type __u32. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ben Hutchings authored
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-