- 13 Mar, 2022 13 commits
-
-
Marc Kleine-Budde authored
This patch increases the number of RX-FIFOs to 3 and the max TX-FIFO depth to 16. This leads to the following default ring configuration. CAN-2.0 mode: | FIFO setup: TEF: 0x400: 8*12 bytes = 96 bytes | FIFO setup: RX-0: FIFO 1/0x460: 32*20 bytes = 640 bytes | FIFO setup: RX-1: FIFO 2/0x6e0: 32*20 bytes = 640 bytes | FIFO setup: RX-2: FIFO 3/0x960: 16*20 bytes = 320 bytes | FIFO setup: TX: FIFO 4/0xaa0: 8*16 bytes = 128 bytes | FIFO setup: free: 224 bytes CAN-FD mode: | FIFO setup: TEF: 0x400: 4*12 bytes = 48 bytes | FIFO setup: RX-0: FIFO 1/0x430: 16*76 bytes = 1216 bytes | FIFO setup: RX-1: FIFO 2/0x8f0: 4*76 bytes = 304 bytes | FIFO setup: TX: FIFO 3/0xa20: 4*72 bytes = 288 bytes | FIFO setup: free: 192 bytes With the previously added ethtool ring configuration support the RAM on the chip can now be runtime configured between RX and TX buffers. Link: https://lore.kernel.org/20220313083640.501791-13-mkl@pengutronix.deSigned-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Marc Kleine-Budde authored
This patch adds support ethtool based configuration for the TX IRQ coalescing added in the previous patch. Link: https://lore.kernel.org/20220313083640.501791-12-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds TX IRQ coalescing support to the driver. The implemented algorithm is similar to the RX IRQ coalescing support added in the previous patch. Link: https://lore.kernel.org/20220313083640.501791-11-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds support ethtool based configuration for the RX IRQ coalescing added in the previous patch. Link: https://lore.kernel.org/20220313083640.501791-10-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds RX IRQ coalescing support to the driver. The mcp251xfd chip doesn't support proper hardware based coalescing, so this patch tries to implemented it in software. The RX-FIFO offers a "FIFO not empty" interrupt, which is used if no coalescing is active. With activated RX IRQ coalescing the "FIFO not empty" interrupt is disabled in the RX IRQ handler and the "FIFO half full" or "FIFO full interrupt" (depending on RX max coalesced frames IRQ) is used instead. To avoid RX CAN frame starvation a hrtimer is setup with RX coalesce usecs IRQ,on timer expiration the "FIFO not empty" is enabled again. Support for ethtool configuration is added in the next patch. Link: https://lore.kernel.org/20220313083640.501791-9-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds runtime configurable RX and TX ring parameters via ethtool to the driver. Link: https://lore.kernel.org/20220313083640.501791-8-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
So far the configuration of the hardware FIFOs is hard coded and depend only on the selected CAN mode (CAN-2.0 or CAN-FD). This patch updates the macros describing the ring, FIFO and RAM layout to prepare for the next patches that add support for runtime configurable ring parameters via ethtool. Link: https://lore.kernel.org/20220313083640.501791-7-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch prepares the driver for runtime configurable RX and TX ring parameters. The actual runtime config support will be added in the next patch. Link: https://lore.kernel.org/20220313083640.501791-6-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds basic ethtool support (to query the current and maximum ring parameters) to the driver. Link: https://lore.kernel.org/20220313083640.501791-5-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds support for coalescing to the RAM layout calculation. Link: https://lore.kernel.org/20220313083640.501791-4-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds a helper function to calculate the ring configuration of the controller based on various constraints, like available RAM, size of RX and TX objects, CAN-mode, number of FIFOs and FIFO depth. Link: https://lore.kernel.org/20220313083640.501791-3-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
In case of an erroneous ring configuration more RAM than available might be used. Change the printf modifier to a signed int to properly print this erroneous value. Fixes: 83daa863 ("can: mcp251xfd: ring: update FIFO setup debug info") Link: https://lore.kernel.org/20220313083640.501791-2-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch fixes the freeing of the "oskb", by using kfree_skb() instead of kfree(). Fixes: 1574481b ("vxcan: remove sk reference in peer skb") Link: https://lore.kernel.org/all/20220311123741.382618-1-mkl@pengutronix.de Cc: Oliver Hartkopp <socketcan@hartkopp.net> Reported-by:
kernel test robot <lkp@intel.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
- 12 Mar, 2022 23 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueDavid S. Miller authored
Tony Nguyen says: ==================== ice: GTP support in switchdev Marcin Szycik says: Add support for adding GTP-C and GTP-U filters in switchdev mode. To create a filter for GTP, create a GTP-type netdev with ip tool, enable hardware offload, add qdisc and add a filter in tc: ip link add $GTP0 type gtp role <sgsn/ggsn> hsize <hsize> ethtool -K $PF0 hw-tc-offload on tc qdisc add dev $GTP0 ingress tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \ action mirred egress redirect dev $VF1_PR By default, a filter for GTP-U will be added. To add a filter for GTP-C, specify enc_dst_port = 2123, e.g.: tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \ enc_dst_port 2123 action mirred egress redirect dev $VF1_PR Note: outer IPv6 offload is not supported yet. Note: GTP-U with no payload offload is not supported yet. ICE COMMS package is required to create a filter as it contains GTP profiles. Changes in iproute2 [1] are required to be able to add GTP netdev and use GTP-specific options (QFI and PDU type). [1] https://lore.kernel.org/netdev/20220211182902.11542-1-wojciech.drewek@intel.com/T --- v2: Add more CC v3: Fix mail thread, sorry for spam v4: Add GTP echo response in gtp module v5: Change patch order v6: Add GTP echo request in gtp module v7: Fix kernel-docs in ice v8: Remove handling of GTP Echo Response v9: Add sending of multicast message on GTP Echo Response, fix GTP-C dummy packet selection v10: Rebase, fixed most 80 char line limits v11: Rebase, collect Harald's Reviewed-by on patch 3 ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Oleksij Rempel authored
In case external PHY is used, we need to take care of embedded PHY. Since there are no methods to disable this PHY from the MAC side and keeping RMII reference clock, we need to suspend it. This patch will reduce electrical noise (PHY is continuing to send FLPs) and power consumption by 0,22W. Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
-
Oleksij Rempel authored
In most cases we use own mdio bus, there is no need to create and store string for the PHY address. Signed-off-by:
-
Oleksij Rempel authored
We already read chipid on probe. There is no need to read it on reset. Signed-off-by:
-
Oleksij Rempel authored
The only difference is the reset code, so remove not needed duplicates. Signed-off-by:
-
Eric Dumazet authored
Before adding yet another possibly contended atomic_long_t, it is time to add per-cpu storage for existing ones: dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler Because many devices do not have to increment such counters, allocate the per-cpu storage on demand, so that dev_get_stats() does not have to spend considerable time folding zero counters. Note that some drivers have abused these counters which were supposed to be only used by core networking stack. v4: should use per_cpu_ptr() in dev_get_stats() (Jakub) v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo) v2: add a missing include (reported by kernel test robot <lkp@intel.com>) Change in netdev_core_stats_alloc() (Jakub) Signed-off-by:Eric Dumazet <edumazet@google.com> Cc: jeffreyji <jeffreyji@google.com> Reviewed-by:
Brian Vazquez <brianvv@google.com> Reviewed-by:
Jakub Kicinski <kuba@kernel.org> Acked-by:
Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.comSigned-off-by:
-
Jakub Kicinski authored
Simon Horman says: ==================== nfp: preliminary support for NFP-3800 This series is the first step to add support to the NFP driver for the new NFP-3800 device. In this first series the goal is to clean up small issues found while adding support for the new device, prepare an abstraction of the differences between the already supported devices and the new Kestrel device and add the new PCI ID. * Patch 1/11 and 2/11 starts by removing some dead code and incorrect assumptions found while working Kestrel support. Patch 3/11, 4/11 and 5/11 cleans up and prepares for adding the new PCI ID for Kestrel. * Patches 6/11, 7/11, 8/11, 9/11, 10/11 adds, plumb and populates a device information structure to abstract the differences between the existed supported devices (NFP-4000, NFP-5000 and NFP-6000) and the new device (NFP3800). * Finally patch 11/11 adds the new PCI ID for Kestrel. More work is needed to drive the new NFP-3800 device after this first batch of patches the foundation is prepared for the follow up work. Thanks to the work of all those who contributed to this work. ==================== Link: https://lore.kernel.org/r/20220311104306.28357-1-simon.horman@corigine.comSigned-off-by:
-
Dirk van der Merwe authored
Enable binding the nfp driver to NFP3800 and NFP3803 devices. The PCIE_SRAM offset is different for the NFP3800 device, which also only supports a single explicit group. Changes to Dirk's work: * 48-bit dma addressing is not ready yet. Keep 40-bit dma addressing for NFP3800. Signed-off-by:
Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
Fei Qin <fei.qin@corigine.com> Signed-off-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Jakub Kicinski authored
NFP3800 has slightly different queue controller range bounds. Use the static chip data instead of defines. This commit still assumes unchanged descriptor format. Later datapath changes will allow adjusting for descriptor accounting. Signed-off-by:
-
Jakub Kicinski authored
The queue controller (QCP) is accessed based on a device specific offset. The NFP3800 device also supports more queues. Furthermore, the NFP3800 VFs also access the QCP differently to how the NFP6000 VFs accesses it, though still indirectly. Fortunately, we can remove the offset all together for both VF types. This is safe for NFP6000 VFs since the offset was effectively a wrap around and only used for convenience to have it set the same as the NFP6000 PF. Use nfp_dev_info to store queue controller parameters. Signed-off-by:
-
Jakub Kicinski authored
In preparation for new chips instead of defines use dev_info constants to store DMA mask length. Signed-off-by:
-
Jakub Kicinski authored
NFP3800 uses a different PCIe configuration to CPP expansion BAR offsets. We don't need to differentiate between the NFP4000, NFP5000 and NFP6000 since they all use the same offsets. Signed-off-by:
-
Jakub Kicinski authored
In preparation for supporting new chip add a driver data structure which will hold per-chip-version information such as register offsets. Plumb it through to the relevant functions (nfpcore and nfp_net). For now only a very simple member holding chip names is added, following commits will add more. Signed-off-by:
-
Jakub Kicinski authored
Make sure the device ID tables are in ascending order. Signed-off-by:
-
Dirk van der Merwe authored
The model number for NFP3800 and newer devices can be completely derived from PluDevice register without subtracting 0x10. Signed-off-by:
-
Dirk van der Merwe authored
The PCI_DEVICE_ID_NETRONOME_NFP6000_VF is available for use and should be used instead of the PCI_DEVICE_NFP6000VF. Meanwhile, PCI_DEVICE_NFP6000VF PCI ID is removed for not being used. Signed-off-by:
-
Christo du Toit authored
Multiple writes cause intermediate pointer values that do not end on complete TX descriptors. The QCP peripheral on the NFP provides a number of access modes. In some access modes, the maximum amount to add must be restricted to a 6bit value. The particular access mode used by _nfp_qcp_ptr_add() has no such restrictions, so the "< NFP_QCP_MAX_ADD" test is unnecessary. Note that trying to add more that the configured ring size in a single add will cause a QCP overflow, caught and handled by the QCP peripheral. Signed-off-by:
Christo du Toit <christo.du.toit@netronome.com> Signed-off-by:
-
Jakub Kicinski authored
NFP driver ABI contains a bit for ring prioritization which was never implemented in the initially envisioned form. Remove it, and open up the possibility of reclaiming for other uses. Signed-off-by:
-
Yang Li authored
The print function dev_err() is redundant because platform_get_irq() already prints an error. Eliminate the follow coccicheck warning: ./drivers/net/ethernet/8390/mcf8390.c:414:2-9: line 414 is redundant because platform_get_irq() already prints an error Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Link: https://lore.kernel.org/r/20220311001756.12234-1-yang.lee@linux.alibaba.comSigned-off-by:
-
Jakub Kicinski authored
netdev_name_node_alt_create() and netdev_name_node_alt_destroy() are only called by rtnetlink, so no need for exports. Reviewed-by:
David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20220310223952.558779-1-kuba@kernel.orgSigned-off-by:
-
Saurabh Sengar authored
In function netvsc_process_raw_pkt for VM_PKT_DATA_USING_XFER_PAGES case there is already a 'return' statement which results 'break' as dead code Signed-off-by:
Saurabh Sengar <ssengar@linux.microsoft.com> Reviewed-by:
Haiyang Zhang <haiyangz@microsoft.com> Link: https://lore.kernel.org/r/1646933534-29493-1-git-send-email-ssengar@linux.microsoft.comSigned-off-by:
-
Christoph Hellwig authored
Both functions are only used by core networking code. Signed-off-by:
Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220310143229.895319-1-hch@lst.deSigned-off-by:
-
Alex Elder authored
In review for commit 8ee7ec48 ("net: ipa: embed interconnect array in the power structure"), Jakub Kicinski suggested that a follow-up patch use struct_size() when computing the size of the IPA power structure, which ends with a flexible array member. Do that. Suggested-by:
Alex Elder <elder@linaro.org> Link: https://lore.kernel.org/r/20220311162423.872645-1-elder@linaro.orgSigned-off-by:
-
- 11 Mar, 2022 4 commits
-
-
Jakub Kicinski authored
Merge tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Johannes Berg says: ==================== brcmfmac * add BCM43454/6 support rtw89 * add support for 160 MHz channels and 6 GHz band * hardware scan support iwlwifi * support UHB TAS enablement via BIOS * remove a bunch of W=1 warnings * add support for channel switch offload * support 32 Rx AMPDU sessions in newer devices * add support for a couple of new devices * add support for band disablement via BIOS mt76 * mt7915 thermal management improvements * SAR support for more mt76 drivers * mt7986 wmac support on mt7915 ath11k * debugfs interface to configure firmware debug log level * debugfs interface to test Target Wake Time (TWT) * provide 802.11ax High Efficiency (HE) data via radiotap ath9k * use hw_random API instead of directly dumping into random.c wcn36xx * fix wcn3660 to work on 5 GHz band ath6kl * add device ID for WLU5150-D81 cfg80211/mac80211 * initial EHT (from 802.11be) support (EHT rates, 320 MHz, larger block-ack) * support disconnect on HW restart * tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (247 commits) mac80211: Add support to trigger sta disconnect on hardware restart mac80211: fix potential double free on mesh join mac80211: correct legacy rates check in ieee80211_calc_rx_airtime nl80211: fix typo of NL80211_IF_TYPE_OCB in documentation mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possible mac80211: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE rtw89: 8852c: process logic efuse map rtw89: 8852c: process efuse of phycap rtw89: support DAV efuse reading operation rtw89: 8852c: add chip::dle_mem rtw89: add page_regs to handle v1 chips rtw89: add chip_info::{h2c,c2h}_reg to support more chips rtw89: add hci_func_en_addr to support variant generation rtw89: add power_{on/off}_func rtw89: read chip version depends on chip ID rtw89: pci: use a struct to describe all registers address related to DMA channel rtw89: pci: add V1 of PCI channel address rtw89: pci: add struct rtw89_pci_info rtw89: 8852c: add 8852c empty files MAINTAINERS: add devicetree bindings entry for mt76 ... ==================== Link: https://lore.kernel.org/r/20220311124029.213470-1-johannes@sipsolutions.netSigned-off-by:
-
Marcin Szycik authored
Add support for creating filters for GTP-U and GTP-C in switchdev mode. Add support for parsing GTP-specific options (QFI and PDU type) and TEID. By default, a filter for GTP-U will be added. To add a filter for GTP-C, specify enc_dst_port = 2123, e.g.: tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \ enc_dst_port 2123 action mirred egress redirect dev $VF1_PR Note: GTP-U with outer IPv6 offload is not supported yet. Note: GTP-U with no payload offload is not supported yet. Signed-off-by:
Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by:
Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by:
Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Michal Swiatkowski authored
Checking only protocol ids while searching for correct FVs can lead to a situation, when incorrect FV will be added to the list. Incorrect means that FV has correct protocol id but incorrect offset. Call ice_get_sw_fv_list with ice_prot_lkup_ext struct which contains all protocol ids with offsets. With this modification allocating and collecting protocol ids list is not longer needed. Signed-off-by:
-
Wojciech Drewek authored
Add a function that checks if a net device type is GTP. Signed-off-by:
Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by:
Harald Welte <laforge@gnumonks.org> Signed-off-by:
-
