The user may change the speed. Use it to replace the default one.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move calling set_speed() from open() to rtl_hw_phy_work_func_t().
Then, we would set the default speed only for first initialization
or after resuming.

Besides, the set_speed() could handle the flag of PHY_RESET which
would be set in rtl_ops.hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the settings of PHY to a work queue and schedule it after
rtl_ops.init().

There are some reasons for this. First, the settings are only
needed for the first time initialization or after the power
down occurs.

Second, the settings are independent with the others.

Last, the settings may take more time than the others. Leave
they in probe() or open() may delay the following flows.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When skip_sw is set and hardware fails to apply filter, return error to
user. This will make error propagation logic similar to the one
currently used in u32 classifier.
Also, changed code to use tc_skip_sw() utility function.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Updates for net-next.

-Add default VLAN support for VFs.
-Add NPAR (NIC partioning) support.
-Add support for new device 5731x and 5741x. GRO logic is different.
-Support new ETHTOOL_{G|S}LINKSETTINGS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To fully support 25G and 50G link settings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some cards do not support autoneg.  The current code does not prevent the
user from enabling autoneg with ethtool on such cards, causing confusion.
Firmware provides the autoneg capability information and we just need to
store it in the support_auto_speeds field in bnxt_link_info struct.
The ethtool set_settings() call will check this field before proceeding
with autoneg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add bnxt_gro_func_5731x() to handle GRO packets for this chip.  The
completion structures used in the new chip have new data to help determine
the header offsets.  The offsets can be off by 4 if the packet is an
internal loopback packet (e.g. from one VF to another VF).  Some additional
logic is added to adjust the offsets if it is a loopback packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer chips require different logic to handle GRO packets.  So refactor
the code so that we can call different functions depending on the chip.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define all the supported chip numbers and chip categories.  Store the
chip_num returned by firmware.  If the call to get the version and chip
number fails, we should abort.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NPAR type is read from bnxt_hwrm_func_qcfg.  Do not allow changing link
parameters if in NPAR mode sinc ethe port is shared among multiple
partitions.  The link parameters are set up by firmware.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the VF driver gets this event, the VF configuration has changed (such
as default VLAN).  The VF driver will initiate a silent reset to pick up
the new configuration.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a default VLAN is added to the VF, the VF driver needs to reset to
pick up the default VLAN ID.  We can use the same tx timeout reset logic
to do that, without the debug output.  This new function, with the
silent parameter to suppress debug output will now serve both purposes.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PF can setup a default VLAN for a VF.  The default VLAN tag is
automatically inserted and stripped without the knowledge of the
stack running on the VF.  The VF driver needs to know that default
VLAN is enabled as VLAN acceleration on the RX side is no longer
supported.  Call netdev_update_features() to fix up the VLAN features
as necessary.  Also, VLAN strip mode must be enabled to strip out
the default VLAN tag.

Only allow VF default VLAN to be set if the firmware spec is >= 1.2.1.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move the enic driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit e858fae2 ("virtio_net: use common code for virtio_net_hdr
and skb GSO conversion") replaced the tun code for header manipulation
with the generic helpers. While doing so, it implictly moved the
skb_partial_csum_set() invocation after eth_type_trans(), which
invalidate the current gso start/offset values.
Fix it by moving the helper invocation before the mac pulling.

Fixes: e858fae2 ("virtio_net: use common code for virtio_net_hdr and
skb GSO conversion")
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_atm returns this when TC_ACT_SHOT classification occurs.

But all other schedulers that use tc_classify
(htb, hfsc, drr, fq_codel ...) return NET_XMIT_SUCCESS | __BYPASS
in this case so just do that in atm.

BATMAN uses it as an intermediate return value to signal
forwarding vs. buffering, but it did not return POLICED to
callers outside of BATMAN.
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since msleep is based on jiffies the PHY reset could take longer
than expected. So use msleep for values greater than 20 msec otherwise
usleep_range.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In IPv6 the ToS values are part of the flowlabel in flowi6 and get
extracted during fib rule lookup, but we forgot to correctly initialize
the flowlabel before the routing lookup.

Reported-by: <liam.mcbirnie@boeing.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net_sched: remove qdisc_is_throttled()

HTB, CBQ and HFSC pay a very high cost updating the qdisc 'throttled'
status that nothing but CBQ seems to use.

CBQ usage is flaky anyway, since no qdisc ->enqueue() updates the
'throttled' qdisc status.

This looks like some 'optimization' that actually cost more than code
without the optimization, and might cause latency issues with CBQ.

In my tests, I could achieve a 8 % performance increase in TCP_RR
workload through HTB qdisc, in presence of throttled classes,
and 5 % without throttled classes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

__QDISC_STATE_THROTTLED bit manipulation is rather expensive
for HTB and few others.

I already removed it for sch_fq in commit f2600cf0
("net: sched: avoid costly atomic operation in fq_dequeue()")
and so far nobody complained.

When one ore more packets are stuck in one or more throttled
HTB class, a htb dequeue() performs two atomic operations
to clear/set __QDISC_STATE_THROTTLED bit, while root qdisc
lock is held.

Removing this pair of atomic operations bring me a 8 % performance
increase on 200 TCP_RR tests, in presence of throttled classes.

This patch has no side effect, since nothing actually uses
disc_is_throttled() anymore.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like it is only there as some optimization attempt.

Since __QDISC_STATE_THROTTLED set/unset is way too expensive,
and netem is the last user, just remove this check.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far no qdisc ever unset the throttled bit at enqueue() time,
so CBQ usage of qdisc_is_throttled() was flaky.

Since __QDISC_STATE_THROTTLED set/unset is way too expensive
considering that only CBQ was eventually caring for this status,
it would make sense to implement a Qdisc ops ->is_throttled()
if we find that this is needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We want to get rid of generic qdisc throttled management,
so this qdisc has to use a private flag.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pramod Kumar says:

====================
Add MDIO bus multiplexer support for iProc SoCs

Broadcom iProc based SoCs use a MDIO bus multiplexer where child buses
could be internal as well external to SoCs. These buses could supports
MDIO transaction compatible to C-22/C-45.

Broadcom MDIO bus multiplexer is an integrated multiplexer where child bus
selection and mdio transaction logic lies inside multiplexer itself.
To accommodate this multiplexer in existing mux framework below changes
were required-

1. Passed MDIO parent bus via mdio_mux_init to MDIO mux framework.

This patch set includes MDIO bus multiplexer driver along with above
framework change. It includes one external bus node having Ethernet PHY
attached and two internal bus node holding PCIe PHYs.

This patch series is based on v4.7-rc1 and is available from github-
repo: https://github.com/Broadcom/arm64-linux.git
branch:mdio-mux-v5

-Changes from v4:
- disabled PCIe PHYs from dtsi and enabled in dts file.

-Changes from v3:
- Unregister and free the parent MDIO bus.
- rebased on net-next/master branch.

Reason for resend:
-Rebased on v4.7-rc1

Changes from v2:
-Addressed Rob's comments in this patch regarding typo/grammers.
-Addressed David's comments regarding local variables order.
-Removed property "mdio-integrated-mux" and used mdiobus_register()
in place of of_mdiobus_regsiter().
-removed usage of IS_ERR_OR_NULL to IS_ERR in PCIe PHY driver.

Changes from v1:
- stop using "brcm,is_c45" from bus node as suggested by Andrew. MDIO
PHY driver will logically OR MII_ADDR_C45 into the address when issues
any C45 MDIO read/write transaction.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add PCI Phy support for Broadcom Northstar2 SoCs.  This driver uses the
interface from the iproc mdio mux driver to enable the devices
respective phys.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Binding doc for NS2 PCIe PHYs.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

iProc based SoCs supports the integrated mdio multiplexer which
has the bus selection as well as mdio transaction generation logic
inside.

This multiplexer has child buses for PCIe, SATA, USB and ETH. These
buses could be internal or external to SOC where PHYs are attached.
These buses could use C-45 or C-22 mdio transaction.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add integrated MDIO multiplexer driver node which contains
two mux PCIe bus and one ethernet bus along with phys
lying on these bus.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add DT binding doc for Broadcom MDIO bus multiplexer driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change "mdio-parent-bus" from mandatory section to optional
as it won't be required by integrated MDIO multiplexer
which has bus selection and mdio transaction generation logic,
integrated inside.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

An integrated multiplexer uses same address space for
"muxed bus selection" and "generation of mdio transaction"
hence its good to register parent bus from mux driver.

Hence added a mechanism where mux driver could register a
parent bus and pass it down to framework via mdio_mux_init api.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now sctp doesn't change socket state upon shutdown reception. It changes
just the assoc state, even though it's a TCP-style socket.

For some cases, if we really need to check sk->sk_state, it's necessary to
fix this issue, at least when we use ss or netstat to dump, we can get a
more exact information.

As an improvement, we will change sk->sk_state when we change asoc->state
to SHUTDOWN_RECEIVED, and also do it in sctp_shutdown to keep consistent
with sctp_close.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2016-06-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
For the next cycle, we have the following:
 * the biggest change is Michał's work on integrating FQ/codel
   with the mac80211 internal software queues
 * cfg80211 connect result gets clarified for the
   "no connection at all" case
 * advertisement of per-interface type capabilities, in case
   they differ (which makes a lot of sense for some capabilities)
 * most of the nl80211 & hwsim unprivileged namespace operation
   changes
 * human-readable VHT capabilities in debugfs
 * some other cleanups, like spelling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Zi Shen Lim says:

====================
arm64 BPF JIT updates

Updates for arm64 eBPF JIT.
The main addition here is implementation of bpf_tail_call.

Changes since v2:
 - None. Resubmit per David Miller.

Changes since v1:
 - Added patch #1 to address build error due to missing header inclusion
   in linux/bpf.h. (Thanks to suggestion and ack by Daniel Borkmann)
   Ordered it ahead of bpf_tail_call patch #2 so build error is not
   triggered.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove superfluous stack frame, saving us 3 instructions for every
LD_ABS or LD_IND.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove superfluous stack frame, saving us 3 instructions for
every JMP_CALL.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for JMP_CALL_X (tail call) introduced by commit 04fd61ab
("bpf: allow bpf programs to tail-call other bpf programs").

bpf_tail_call() arguments:
  ctx   - context pointer passed to next program
  array - pointer to map which type is BPF_MAP_TYPE_PROG_ARRAY
  index - index inside array that selects specific program to run

In this implementation arm64 JIT jumps into callee program after prologue,
so callee program reuses the same stack. For tail_call_cnt, we use the
callee-saved R26 (which was already saved/restored but previously unused
by JIT).

With this patch a tail call generates the following code on arm64:

  if (index >= array->map.max_entries)
      goto out;

  34:   mov     x10, #0x10                      // #16
  38:   ldr     w10, [x1,x10]
  3c:   cmp     w2, w10
  40:   b.ge    0x0000000000000074

  if (tail_call_cnt > MAX_TAIL_CALL_CNT)
      goto out;
  tail_call_cnt++;

  44:   mov     x10, #0x20                      // #32
  48:   cmp     x26, x10
  4c:   b.gt    0x0000000000000074
  50:   add     x26, x26, #0x1

  prog = array->ptrs[index];
  if (prog == NULL)
      goto out;

  54:   mov     x10, #0x68                      // #104
  58:   ldr     x10, [x1,x10]
  5c:   ldr     x11, [x10,x2]
  60:   cbz     x11, 0x0000000000000074

  goto *(prog->bpf_func + prologue_size);

  64:   mov     x10, #0x20                      // #32
  68:   ldr     x10, [x11,x10]
  6c:   add     x10, x10, #0x20
  70:   br      x10
  74:
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>