- 20 Jun, 2017 40 commits
-
-
Stanimir Varbanov authored
This adds encoder part of the driver plus encoder controls. Signed-off-by:
Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Stanimir Varbanov authored
This consists of video decoder implementation plus decoder controls. Signed-off-by:
-
Stanimir Varbanov authored
* core.c has implemented the platform driver methods, file operations and v4l2 registration. * helpers.c has implemented common helper functions for: - buffer management - vb2_ops and functions for format propagation, - functions for allocating and freeing buffers for internal usage. The buffer parameters describing internal buffers depends on current format, resolution and codec. - functions for calculation of current load of the hardware. Depending on the count of instances and resolutions it selects the best clock rate for the video core. * firmware loader Signed-off-by:
-
Stanimir Varbanov authored
Add an entry for Venus video encoder/decoder accelerator driver. Signed-off-by:
-
Stanimir Varbanov authored
Add binding document for Venus video encoder/decoder driver Cc: Rob Herring <robh+dt@kernel.org> Cc: devicetree@vger.kernel.org Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Stanimir Varbanov authored
this add functions for: - remove buffers from src/dst queue by index - remove exact buffer from src/dst queue also extends m2m API to iterate over a list of src/dst buffers in safely and non-safely manner. Signed-off-by:
-
Mauro Carvalho Chehab authored
Linux 4.12-rc6 * tag 'v4.12-rc6': (813 commits) Linux 4.12-rc6 mm: larger stack guard gap, between vmas virtio_balloon: disable VIOMMU support mm: correct the comment when reclaimed pages exceed the scanned pages userfaultfd: shmem: handle coredumping in handle_userfault() mm: numa: avoid waiting on freed migrated pages swap: cond_resched in swap_cgroup_prepare() mm/memory-failure.c: use compound_head() flags for huge pages perf unwind: Report module before querying isactivation in dwfl unwind fs: pass on flags in compat_writev objtool: Add fortify_panic as __noreturn function powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks drm: mxsfb_crtc: Reset the eLCDIF controller drm/mgag200: Fix to always set HiPri for G200e4 V2 i2c: ismt: fix wrong device address when unmap the data buffer i2c: rcar: use correct length when unmapping DMA powerpc/xive: Fix offset for store EOI MMIOs drm/tegra: Correct idr_alloc() minimum id drm/tegra: Fix lockup on a use of staging API ... Signed-off-by: -
Mauro Carvalho Chehab authored
As reported by gcc: drivers/media/i2c/ov13858.c:953:20: warning: duplicate const drivers/media/i2c/ov13858.c:953:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier] static const const s64 link_freq_menu_items[OV13858_NUM_OF_LINK_FREQS] = { ^~~~~ Signed-off-by: -
Andy Shevchenko authored
There is no need to split long string literals. Join them back. No functional change intended. Signed-off-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Rajmohan Mani authored
DW9714 is a 10 bit DAC, designed for linear control of voice coil motor. This driver creates a V4L2 subdevice and provides control to set the desired focus. [Sakari Ailus: Add MAINTAINERS entry.] Signed-off-by:
Rajmohan Mani <rajmohan.mani@intel.com> Signed-off-by:
-
Hyungwoo Yang authored
This patch adds driver for Omnivision's ov13858 sensor, the driver supports following features: - manual exposure/gain(analog and digital) control support - two link frequencies - VBLANK/HBLANK support - test pattern support - media controller support - runtime pm support - supported resolutions + 4224x3136 at 30FPS + 2112x1568 at 30FPS(default) and 60FPS + 2112x1188 at 30FPS(default) and 60FPS + 1056x784 at 30FPS(default) and 60FPS [Sakari Ailus: use V4L2_CID_DIGITAL_GAIN instead, add MAINTAINERS entry.] Signed-off-by:
Hyungwoo Yang <hyungwoo.yang@intel.com> Signed-off-by:
-
Sakari Ailus authored
Elaborate the differences between V4L2_CID_GAIN and gain-type specific V4L2_CID_DIGITAL_GAIN and V4L2_CID_ANALOGUE_GAIN. Signed-off-by:
-
Sakari Ailus authored
Add V4L2_CID_DIGITAL_GAIN to control explicitly digital gain. We already have analogue gain control which the digital gain control complements. Typically higher quality images are obtained using analogue gain only as the digital gain does not add information to the image (rather it may remove it). Signed-off-by:
-
Steve Longerbeam authored
Add maintainer entry for the imx-media driver. Signed-off-by:
Steve Longerbeam <steve_longerbeam@mentor.com> Acked-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Marek Vasut authored
Calling S_STREAM OFF multiple times on a video device is valid, although dubious, practice. Instead of warning about it and setting stream count lower than zero, just ignore the subsequent S_STREAM calls and correct the stream count to zero. Signed-off-by:
Marek Vasut <marex@denx.de> Signed-off-by:
-
Steve Longerbeam authored
This patch adds a call to imx_media_fill_default_mbus_fields() in the *_try_fmt() functions at the sink pads, to set empty field order and colorimetry parameters. If the field order is set to ANY, choose the currently set field order at the sink pad. If the colorspace is set to DEFAULT, choose the current colorspace at the sink pad. If any of xfer_func, ycbcr_enc or quantization are set to DEFAULT, either choose the current sink pad setting, or the default setting for the new colorspace, if non-DEFAULT colorspace was given. If a format is destined to be routed through the Image Converter, fixed quantization and Y`CbCr encoding must be set. Colorimetry is also propagated from sink to source pads anywhere this has not already been done. Signed-off-by:
-
Russell King authored
Add support for enumerating frame sizes and frame intervals from the first subdev via the V4L2 interfaces. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Russell King authored
Add frame size and frame interval enumeration to CSI. CSI can downscale the image independently horizontally and vertically by a factor of two, which enumerates to four different frame sizes at the output pads. The input pad supports a range of frame sizes. CSI can also drop frames, resulting in frame rate reduction, so enumerate the resulting possible output frame rates. Signed-off-by:
-
Philipp Zabel authored
Move the crop rectangle to the sink pad and add a sink compose rectangle to configure scaling. Also propagate rectangles from sink pad to crop rectangle, to compose rectangle, and to the source pads both in ACTIVE and TRY variants of set_fmt/selection, and initialize the default crop and compose rectangles. Signed-off-by:
-
Philipp Zabel authored
The CSI can skip any out of up to 6 input frames, allowing to reduce the frame rate at the output pads by small fractions. Signed-off-by:
-
Philipp Zabel authored
The IDMAC supports burst sizes of up to 32 pixels for interleaved YUV formats and up to 64 pixels for planar YUV formats. Signed-off-by:
-
Russell King authored
Bayer formats must be treated as generic data and passthrough mode must be used. Add the correct setup for these formats. - added check to csi_link_validate() to verify that destination is IDMAC output pad when passthrough conditions exist: bayer formats and 16-bit parallel buses. Signed-off-by:
-
Steve Longerbeam authored
Adds MIPI CSI-2 Receiver subdev driver. This subdev is required for sensors with a MIPI CSI2 interface. - Switch from the v4l2_of_ APIs to the v4l2_fwnode_ APIs. - Add the function csi2ipu_gasket_init() to initialize the gasket at s_power(ON). The gasket needs to be programmed with the correct color component ordering to handle UYVY vs. YUYV ordered mbus formats from sensors. Note that the description of the CSI2IPU_GASKET register in the i.MX6 reference manual is wrong w.r.t bit 2 (the manual refers to this register as CSI2_SW_RST): setting bit 2 selects YUYV order, not UYVY. Signed-off-by:
-
Steve Longerbeam authored
This is a set of three media entity subdevice drivers for the i.MX Image Converter: - Pre-process Router: Takes input frames from CSI0, CSI1, or VDIC. Two output pads enable either or both of the preprocess tasks below. If the input is from one of the CSIs, both proprocess task links can be enabled to process frames from that CSI simultaneously. If the input is the VDIC, only the Pre-processing Viewfinder task link can be enabled. - Pre-processing Encode task: video frames are routed directly from the CSI and can be scaled, color-space converted, and rotated. Scaled output is limited to 1024x1024 resolution. Output frames are routed to the prpenc capture device. - Pre-processing Viewfinder task: this task can perform the same conversions as the pre-process encode task, but in addition can be used for hardware motion compensated deinterlacing. Frames can come either directly from the CSI or from the VDIC. Scaled output is limited to 1024x1024 resolution. Output frames are routed to the prpvf capture device. Signed-off-by:
-
Steve Longerbeam authored
This is a media entity subdevice driver for the i.MX Video De-Interlacing or Combining Block. So far this entity does not implement the Combining function but only motion compensated deinterlacing. Video frames are received from the CSI and are routed to the IC PRPVF entity. Signed-off-by:
-
Steve Longerbeam authored
This is a media entity subdevice for the i.MX Camera Sensor Interface module. - Added support for negotiation of frame intervals. - Fixed cropping rectangle negotiation at input and output pads. - Added support for /2 downscaling, if the output pad dimension(s) are 1/2 the crop dimension(s) at csi_setup() time. Signed-off-by:
-
Steve Longerbeam authored
This is the capture device interface driver that provides the v4l2 user interface. Frames can be received from various sources: - directly from CSI for capturing unconverted images directly from camera sensors. - from the IC pre-process encode task. - from the IC pre-process viewfinder task. Signed-off-by:
-
Steve Longerbeam authored
Add a TODO file. Signed-off-by:
-
Steve Longerbeam authored
Add the core media driver for i.MX SOC. Switch from the v4l2_of_ APIs to the v4l2_fwnode_ APIs. Add the bayer formats to imx-media's list of supported pixel and bus formats. Signed-off-by:
-
Steve Longerbeam authored
This adds a header file for use by userspace programs wanting to interact with the i.MX media driver. It defines custom events and v4l2 controls for the i.MX v4l2 subdevices. Signed-off-by:
-
Steve Longerbeam authored
Add bindings documentation for the i.MX media driver. Signed-off-by:
-
Steve Longerbeam authored
Add maintainer entry for the OV5640 V4L2 sensor driver. Signed-off-by:
-
Steve Longerbeam authored
This driver is based on ov5640_mipi.c from Freescale imx_3.10.17_1.0.0_beta branch, modified heavily to bring forward to latest interfaces and code cleanup. Signed-off-by:
-
Steve Longerbeam authored
Add device tree binding documentation for the OV5640 camera sensor. Signed-off-by:
-
Philipp Zabel authored
Add maintainer entry for the video multiplexer v4l2 subdevice driver that will control video bus multiplexers via the multiplexer framework. Signed-off-by:
-
Philipp Zabel authored
This driver can handle SoC internal and external video bus multiplexers, controlled by mux controllers provided by the mux controller framework, such as MMIO register bitfields or GPIOs. The subdevice passes through the mbus configuration of the active input to the output side. Since the mux framework is not yet merged, this driver contains temporary mmio-mux support to work without the framework. The driver should be converted to use the multiplexer API once the "mux: minimal mux subsystem" and "mux: mmio-based syscon mux controller" patches are merged. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
Pavel Machek <pavel@ucw.cz> [hans.verkuil@cisco.com: add 'select REGMAP' to Kconfig] Signed-off-by:
-
Philipp Zabel authored
Add two new media entity function definitions for video multiplexers and video interface bridges. - renamed MEDIA_ENT_F_MUX to MEDIA_ENT_F_VID_MUX Signed-off-by:
-
Philipp Zabel authored
Add bindings documentation for the video multiplexer device. Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.co.uk> Acked-by:
-
Mauro Carvalho Chehab authored
load is an unsigned integer. So, it is always bigger or equal to zero, as reported by gcc: drivers/media/i2c/max2175.c: In function 'max2175_refout_load_to_bits': drivers/media/i2c/max2175.c:1272:11: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits] if (load >= 0 && load <= 40) ^~ Signed-off-by: -
Ramesh Shanmugasundaram authored
Add maintainter entry for the R-Car DRIF and MAX2175 drivers. Signed-off-by:
Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Signed-off-by:
Hans Verkuil <hansverk@cisco.com> Signed-off-by:
-
