QoS offload needs Ethernet Offload (ETHOFLD) resources present in the
NIC. These resources are shared with other ULDs. So, query firmware
for the available number of traffic classes, as well as, start and
end indices (EOTID) of the ETHOFLD region.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I forgot to change last_packets field in struct net_rate_estimator.

Without this fix, rate estimators would misbehave after more
than 2^32 packets have been sent.

Another solution would be to be careful and only use the
32 least significant bits of packets counters, but we have
a hole in net_rate_estimator structure and this looks
easier to read/maintain.

Fixes: d0083d98 ("net_sched: extend packet counter to 64bit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

phylink_set_port_modes will be compiled if CONFIG_PHYLINK enabled,
dpaa2_mac_validate will be compiled if CONFIG_FSL_DPAA2_ETH enabled,
it should select CONFIG_PHYLINK when dpaa2_mac_validate call
phylink_set_port_modes

drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_validate':
dpaa2-mac.c:(.text+0x3a1): undefined reference to `phylink_set_port_modes'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_connect':
dpaa2-mac.c:(.text+0x91a): undefined reference to `phylink_create'
dpaa2-mac.c:(.text+0x94e): undefined reference to `phylink_of_phy_connect'
dpaa2-mac.c:(.text+0x97f): undefined reference to `phylink_destroy'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_disconnect':
dpaa2-mac.c:(.text+0xa9f): undefined reference to `phylink_disconnect_phy'
dpaa2-mac.c:(.text+0xab0): undefined reference to `phylink_destroy'
make: *** [vmlinux] Error 1

Fixes: 71947923 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2019-11-06

This series contains updates to ice driver only.

Scott adds ethtool -m support so that we can read eeprom data on SFP/OSFP
modules.

Anirudh updates the return value to properly reflect when SRIOV is not
supported.

Md Fahad updates the driver to handle a change in the NVM, where the
boot configuration section was moved to the Preserved Field Area (PFA)
of the NVM.

Paul resolves an issue when DCBx requests non-contiguous TCs, transmit
hangs could occur, so configure a default traffic class (TC0) in these
cases to prevent traffic hangs.  Adds a print statement to notify the
user when unsupported modules are inserted.

Bruce fixes up the driver unload code flow to ensure we do not clear the
interrupt scheme until the reset is complete, otherwise a hardware error
may occur.

Dave updates the DCB initialization to set is_sw_lldp boolean when the
firmware has been detected to be in an untenable state.  This will
ensure that the firmware is in a known state.

Michal saves off the PCI state and I/O BARs address after PCI bus reset
so that after the reset, device registers can be read.  Also adds a NULL
pointer check to prevent a potential kernel panic.

Mitch resolves an issue where VF's on PF's other than 0 were not seeing
resets by using the per-PF VF ID instead of the absolute VF ID.

Krzysztof does some code cleanup to remove a unneeded wrapper and
reduces the code complexity.

Brett reduces confusion by changing the name of ice_vc_dis_vf() to
ice_vc_reset_vf() to better describe what the function is actually
doing.

v2: dropped patch 3 "ice: Add support for FW recovery mode detection"
    from the origin al series, while Ani makes changes based on
    community feedback to implement devlink into the changes.
v3: dropped patch 1 "ice: implement set_eeprom functionality" due to a
    bug found and additional changes will be needed when Ani implements
    devlink in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

mv88e6xxx_g2_atu_stats_get() takes two parameters. Make the stub
function also take two, otherwise we get compile errors.

Fixes: c5f299d5 ("net: dsa: mv88e6xxx: global1_atu: Add helper for get next")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Walle says:

====================
net: phy: at803x device tree binding

Adds a device tree binding to configure the clock and the RGMII voltage.

Changes since v1:
 - rebased to latest net-next
 - renamed "Atheros" to "Qualcomm Atheros"
 - add a new patch to remove config_init() from AR9331

Changes since the RFC:
 - renamed the Kconfig entry to "Qualcomm Atheros.." and reordered the
   item
 - renamed the prefix from atheros to qca
 - use the correct name AR803x (instead of AT803x) in new files and
   dt-bindings.
 - listed the PHY maintainers in the new schema. Hopefully, thats ok.
 - fixed a typo in the bindings schema
 - run dtb_checks and dt_binding_check and fixed the schema
 - dropped the rgmii-io-1v8 property; instead provide two regulators vddh
   and vddio, add one consumer vddio-supply
 - fix the clock settings for the AR8030/AR8035
 - only the AR8031 supports chaning the LDO and the PLL mode in software.
   Check if we have the correct PHY.
 - new patch to mention the AR8033 which is the same as the AR8031 just
   without PTP support
 - new patch which corrects any displayed PHY names and comments. Be
   consistent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

According to its datasheet, the internal PHY doesn't have debug
registers nor MMDs. Since config_init() only configures delays and
clocks and so on in these registers it won't be needed on this PHY.
Remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix at least the displayed strings. The actual name of the chip is
AR803x.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AR8033 is the AR8031 without PTP support. All other registers are
the same. Unfortunately, they share the same PHY ID. Therefore, we
cannot distinguish between the one with PTP support and the one without.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document the Atheros AR803x PHY bindings.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The name of the PHY is actually AR803x not AT803x. Additionally, add the
name of the vendor and mention the AR8031 support.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reading tp->recvmsg_inq after socket lock is released
raises a KCSAN warning [1]

Replace has_tss & has_cmsg by cmsg_flags and make
sure to not read tp->recvmsg_inq a second time.

[1]
BUG: KCSAN: data-race in tcp_chrono_stop / tcp_recvmsg

write to 0xffff888126adef24 of 2 bytes by interrupt on cpu 0:
 tcp_chrono_set net/ipv4/tcp_output.c:2309 [inline]
 tcp_chrono_stop+0x14c/0x280 net/ipv4/tcp_output.c:2338
 tcp_clean_rtx_queue net/ipv4/tcp_input.c:3165 [inline]
 tcp_ack+0x274f/0x3170 net/ipv4/tcp_input.c:3688
 tcp_rcv_established+0x37e/0xf50 net/ipv4/tcp_input.c:5696
 tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1561
 tcp_v4_rcv+0x19dc/0x1bb0 net/ipv4/tcp_ipv4.c:1942
 ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204
 ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
 NF_HOOK include/linux/netfilter.h:305 [inline]
 NF_HOOK include/linux/netfilter.h:299 [inline]
 ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
 dst_input include/net/dst.h:442 [inline]
 ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
 NF_HOOK include/linux/netfilter.h:305 [inline]
 NF_HOOK include/linux/netfilter.h:299 [inline]
 ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
 __netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010
 __netif_receive_skb+0x37/0xf0 net/core/dev.c:5124
 netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5214
 napi_skb_finish net/core/dev.c:5677 [inline]
 napi_gro_receive+0x28f/0x330 net/core/dev.c:5710

read to 0xffff888126adef25 of 1 bytes by task 7275 on cpu 1:
 tcp_recvmsg+0x77b/0x1a30 net/ipv4/tcp.c:2187
 inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
 sock_recvmsg_nosec net/socket.c:871 [inline]
 sock_recvmsg net/socket.c:889 [inline]
 sock_recvmsg+0x92/0xb0 net/socket.c:885
 sock_read_iter+0x15f/0x1e0 net/socket.c:967
 call_read_iter include/linux/fs.h:1889 [inline]
 new_sync_read+0x389/0x4f0 fs/read_write.c:414
 __vfs_read+0xb1/0xc0 fs/read_write.c:427
 vfs_read fs/read_write.c:461 [inline]
 vfs_read+0x143/0x2c0 fs/read_write.c:446
 ksys_read+0xd5/0x1b0 fs/read_write.c:587
 __do_sys_read fs/read_write.c:597 [inline]
 __se_sys_read fs/read_write.c:595 [inline]
 __x64_sys_read+0x4c/0x60 fs/read_write.c:595
 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7275 Comm: sshd Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: b75eba76 ("tcp: send in-queue bytes in cmsg upon read")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk->sk_backlog.tail might be read without holding the socket spinlock,
we need to add proper READ_ONCE()/WRITE_ONCE() to silence the warnings.

KCSAN reported :

BUG: KCSAN: data-race in tcp_add_backlog / tcp_recvmsg

write to 0xffff8881265109f8 of 8 bytes by interrupt on cpu 1:
 __sk_add_backlog include/net/sock.h:907 [inline]
 sk_add_backlog include/net/sock.h:938 [inline]
 tcp_add_backlog+0x476/0xce0 net/ipv4/tcp_ipv4.c:1759
 tcp_v4_rcv+0x1a70/0x1bd0 net/ipv4/tcp_ipv4.c:1947
 ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204
 ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
 NF_HOOK include/linux/netfilter.h:305 [inline]
 NF_HOOK include/linux/netfilter.h:299 [inline]
 ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
 dst_input include/net/dst.h:442 [inline]
 ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
 NF_HOOK include/linux/netfilter.h:305 [inline]
 NF_HOOK include/linux/netfilter.h:299 [inline]
 ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
 __netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:4929
 __netif_receive_skb+0x37/0xf0 net/core/dev.c:5043
 netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5133
 napi_skb_finish net/core/dev.c:5596 [inline]
 napi_gro_receive+0x28f/0x330 net/core/dev.c:5629
 receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
 virtnet_receive drivers/net/virtio_net.c:1323 [inline]
 virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
 napi_poll net/core/dev.c:6311 [inline]
 net_rx_action+0x3ae/0xa90 net/core/dev.c:6379
 __do_softirq+0x115/0x33f kernel/softirq.c:292
 invoke_softirq kernel/softirq.c:373 [inline]
 irq_exit+0xbb/0xe0 kernel/softirq.c:413
 exiting_irq arch/x86/include/asm/apic.h:536 [inline]
 do_IRQ+0xa6/0x180 arch/x86/kernel/irq.c:263
 ret_from_intr+0x0/0x19
 native_safe_halt+0xe/0x10 arch/x86/kernel/paravirt.c:71
 arch_cpu_idle+0x1f/0x30 arch/x86/kernel/process.c:571
 default_idle_call+0x1e/0x40 kernel/sched/idle.c:94
 cpuidle_idle_call kernel/sched/idle.c:154 [inline]
 do_idle+0x1af/0x280 kernel/sched/idle.c:263
 cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:355
 start_secondary+0x208/0x260 arch/x86/kernel/smpboot.c:264
 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:241

read to 0xffff8881265109f8 of 8 bytes by task 8057 on cpu 0:
 tcp_recvmsg+0x46e/0x1b40 net/ipv4/tcp.c:2050
 inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
 sock_recvmsg_nosec net/socket.c:871 [inline]
 sock_recvmsg net/socket.c:889 [inline]
 sock_recvmsg+0x92/0xb0 net/socket.c:885
 sock_read_iter+0x15f/0x1e0 net/socket.c:967
 call_read_iter include/linux/fs.h:1889 [inline]
 new_sync_read+0x389/0x4f0 fs/read_write.c:414
 __vfs_read+0xb1/0xc0 fs/read_write.c:427
 vfs_read fs/read_write.c:461 [inline]
 vfs_read+0x143/0x2c0 fs/read_write.c:446
 ksys_read+0xd5/0x1b0 fs/read_write.c:587
 __do_sys_read fs/read_write.c:597 [inline]
 __se_sys_read fs/read_write.c:595 [inline]
 __x64_sys_read+0x4c/0x60 fs/read_write.c:595
 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 8057 Comm: syz-fuzzer Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the phy_mode() function to return the if_mode through an
argument, similar to the new form of of_get_phy_mode().
This will help with handling errors in a common manner and also will fix
an always true condition.

Fixes: 0c65b2b9 ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 69c51582ff786 ("dpif-netlink: don't allocate per
thread netlink sockets"), in Open vSwitch ovs-vswitchd, has
changed the number of allocated sockets to just one per port
by moving the socket array from a per handler structure to
a per datapath one. In the kernel datapath, a vport will have
only one socket in most case, if so select it directly in
fast-path.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the DMA memory resource get failed case, the error is not
set and 0 will be returned. Fix it by removing redundant check
since devm_ioremap_resource() will handle it.

Fixes: 28ef9ebd ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function ptp_clock_register() returns ERR_PTR() and never returns
NULL. The NULL test should be removed.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the missing unlock before return from function idtcm_probe()
in the error handling case.

Fixes: 3a6ba7dc ("ptp: Add a ptp clock driver for IDT ClockMatrix.")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When preparing tunnel packets for the link failover or synchronization,
as for the safe algorithm, we added a dummy packet on the pair link but
never sent it out. In the case of failover, the pair link will be reset
anyway. But for link synching, it will always result in retransmission
of the dummy packet after that.
We have also observed that such the retransmission at the early stage
when a new node comes in a large cluster will take some time and hard
to be done, leading to the repeated retransmit failures and the link is
reset.

Since in commit 4929a932 ("tipc: optimize link synching mechanism")
we have already built a dummy 'TUNNEL_PROTOCOL' message on the new link
for the synchronization, there's no need for the dummy on the pair one,
this commit will skip it when the new mechanism takes in place. In case
nothing exists in the pair link's transmq, the link synching will just
start and stop shortly on the peer side.

The patch is backward compatible.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
lwtunnel: add ip and ip6 options setting and dumping

With this patchset, users can configure options by ip route encap
for geneve, vxlan and ersapn lwtunnel, like:

  # ip r a 1.1.1.0/24 encap ip id 1 geneve class 0 type 0 \
    data "1212121234567890" dst 10.1.0.2 dev geneve1

  # ip r a 1.1.1.0/24 encap ip id 1 vxlan gbp 456 \
    dst 10.1.0.2 dev erspan1

  # ip r a 1.1.1.0/24 encap ip id 1 erspan ver 1 idx 123 \
    dst 10.1.0.2 dev erspan1

iproute side patch is attached on the reply of this mail.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on the code framework built on the last patch, to
support setting and dumping for vxlan, we only need to
add ip_tun_parse_opts_erspan() for .build_state and
ip_tun_fill_encap_opts_erspan() for .fill_encap and
if (tun_flags & TUNNEL_ERSPAN_OPT) for .get_encap_size.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on the code framework built on the last patch, to
support setting and dumping for vxlan, we only need to
add ip_tun_parse_opts_vxlan() for .build_state and
ip_tun_fill_encap_opts_vxlan() for .fill_encap and
if (tun_flags & TUNNEL_VXLAN_OPT) for .get_encap_size.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To add options setting and dumping, .build_state(), .fill_encap() and
.get_encap_size() in ip_tun_lwt_ops needs to be extended:

ip_tun_build_state():
  ip_tun_parse_opts():
    ip_tun_parse_opts_geneve()

ip_tun_fill_encap_info():
  ip_tun_fill_encap_opts():
    ip_tun_fill_encap_opts_geneve()

ip_tun_encap_nlsize()
   ip_tun_opts_nlsize():
     if (tun_flags & TUNNEL_GENEVE_OPT)

ip_tun_parse_opts(), ip_tun_fill_encap_opts() and ip_tun_opts_nlsize()
processes LWTUNNEL_IP_OPTS.

ip_tun_parse_opts_geneve(), ip_tun_fill_encap_opts_geneve() and
if (tun_flags & TUNNEL_GENEVE_OPT) processes LWTUNNEL_IP_OPTS_GENEVE.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When comparing two tun_info, dst_cache member should have been skipped,
as dst_cache is a per cpu pointer and they are always different values
even in two tun_info with the same keys.

So this patch is to skip dst_cache member and compare the key, mode and
options_len only. For the future opts setting support, also to compare
options.

Fixes: 2d798499 ("lwtunnel: ip tunnel: fix multiple routes with different encap")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without options copied to the dst tun_info in iptunnel_metadata_reply()
called by arp_process for handling arp_request, the generated arp_reply
packet may be dropped or sent out with wrong options for some tunnels
like erspan and vxlan, and the traffic will break.

Fixes: 63d008a4 ("ipv4: send arp replies to the correct tunnel")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With huge cluster (e.g >200nodes), the amount of that flow:
gap -> retransmit packet -> acked will take time in case of STATE_MSG
dropped/delayed because a lot of traffic. This lead to 1.5 sec tolerance
value criteria made link easy failure around 2nd, 3rd of failed
retransmission attempts.

Instead of re-introduced criteria of 99 faled retransmissions to fix the
issue, we increase failure detection timer to ten times tolerance value.

Fixes: 77cf8edb ("tipc: simplify stale link failure criteria")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two improvements when re-calculate cluster capabilities:

- When deleting a specific down node, need to re-calculate.
- In tipc_node_cleanup(), do not need to re-calculate if node
is still existing in cluster.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon
Signed-off-by: David S. Miller <davem@davemloft.net>

Added the following traceroute tests.

IPV6:
Verify that in this scenario

       ------------------------ N2
        |                    |
      ------              ------  N3  ----
      | R1 |              | R2 |------|H2|
      ------              ------      ----
        |                    |
       ------------------------ N1
                 |
                ----
                |H1|
                ----

where H1's default route goes through R1 and R1's default route goes
through R2 over N2, traceroute6 from H1 to H2 reports R2's address
on N2 and not N1.

IPV4:
Verify that traceroute from H1 to H2 shows 1.0.1.1 in this scenario

                   1.0.3.1/24
---- 1.0.1.3/24    1.0.1.1/24 ---- 1.0.2.1/24    1.0.2.4/24 ----
|H1|--------------------------|R1|--------------------------|H2|
----            N1            ----            N2            ----

where net.ipv4.icmp_errors_use_inbound_ifaddr is set on R1 and
1.0.3.1/24 and 1.0.1.1/24 are respectively R1's primary and secondary
address on N1.

v2: fixed some typos, and have bridge in R1 instead of R2 in IPV6 test.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the device is not capable of supporting SR-IOV -ENODEV is being
returned; -EOPNOTSUPP is more appropriate.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_vc_dis_vf() tells iavf that it's going to perform a reset
and then performs a software reset. This is misleading based on
the function name because the VF does not get disabled. So fix
this by changing the name to ice_vc_reset_vf().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_cleanup_hdrs() has been stripped of most of its content, it only serves
as a wrapper for eth_skb_pad(). We can get rid of it altogether and
simplify the codebase.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Print message to inform user of PCI link speed and width.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Print message to inform user if unsupported module is inserted, and
extend the topology / configuration detection.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF_MBX_ARQLEN register array is per-PF, not global, so we should not
use the absolute VF ID as an index. Instead, use the per-PF VF ID.

This fixes an issue with VFs on PFs other than 0 not seeing reset.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Without this check rebuild vsi can lead to kernel panic.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Save state to correct recovery memory and I/O BARs address
after PCI bus reset. Without this after reset kernel can't
read device registers.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Adjust ice_init_dcb to set the is_sw_lldp boolean
in the case where the FW has been detected to be
in an untenable state such that the driver
should forcibly make sure it is off.

This will ensure that the FW is in a known state.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

As part of the driver unload flow, a PF reset is issued which may still
cause an interrupt to be generated by the device.  Do not clear the
interrupt scheme until the reset is complete and there are no pending
transactions otherwise a hardware error may occur.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If DCBx request non-contiguous TCs, then the driver will configure default
traffic class (TC0). This is done to prevent Tx hang since the driver
currently does not support non-contiguous TC.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>