The renameat2() system call was only wired up for x86-64.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Link: http://lkml.kernel.org/r/1397211951-20549-2-git-send-email-miklos@szeredi.hu
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

Pull spi fixes from Mark Brown:
 "A few driver specific fixes, the main one being the fix for handling
  of complete callbacks that are open coded in individual drivers to
  allow callers to omit the completion.  As we move things into the core
  that sort of issue should become less and less common"

* tag 'spi-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: qup: Depend on ARCH_QCOM
  spi: efm32: Update binding document to make "efm32,location" property optional
  spi: omap2-mcspi: Convert to use devm_kcalloc
  spi: Always check complete callback before calling it

Merge tag 'regulator-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "A few driver specific fixes that have come in over the merge window,
  all only relevant for the specific driver"

* tag 'regulator-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: bcm590xx: Set n_voltages for linear reg
  regulator: s5m8767: Fix carried over ena_gpio assignment
  regulator: s2mps11: Don't check enable_shift before setting enable ramp rate
  regulator: s2mpa01: Don't check enable_shift before setting enable ramp rate

Pull regmap fix from Mark Brown:
 "regmap: Fix for nodev mode

  Add mising braces so that the nodev mode actually works (which was a
  bit of an oversight)"

Testing schmesting.  We don't need not steenking testing.  We have
deadlines to beat, and new code to write.

* tag 'regmap-v3.15-nodev' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: adds missing braces in regmap_init()

Pull more ACPI and power management fixes and updates from Rafael Wysocki:
 "This is PM and ACPI material that has emerged over the last two weeks
  and one fix for a CPU hotplug regression introduced by the recent CPU
  hotplug notifiers registration series.

  Included are intel_idle and turbostat updates from Len Brown (these
  have been in linux-next for quite some time), a new cpufreq driver for
  powernv (that might spend some more time in linux-next, but BenH was
  asking me so nicely to push it for 3.15 that I couldn't resist), some
  cpufreq fixes and cleanups (including fixes for some silly breakage in
  a couple of cpufreq drivers introduced during the 3.14 cycle),
  assorted ACPI cleanups, wakeup framework documentation fixes, a new
  sysfs attribute for cpuidle and a new command line argument for power
  domains diagnostics.

  Specifics:

   - Fix for a recently introduced CPU hotplug regression in ARM KVM
     from Ming Lei.

   - Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
     cpufreq drivers introduced during the 3.14 cycle (-stable material)
     from Chen Gang and Viresh Kumar.

   - New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
     from Gautham R Shenoy and Srivatsa S Bhat.

   - Exynos cpufreq driver fix preventing it from being included into
     multiplatform builds that aren't supported by it from Sachin Kamat.

   - cpufreq cleanups related to the usage of the driver_data field in
     struct cpufreq_frequency_table from Viresh Kumar.

   - cpufreq ppc driver cleanup from Sachin Kamat.

   - Intel BayTrail support for intel_idle and ACPI idle from Len Brown.

   - Intel CPU model 54 (Atom N2000 series) support for intel_idle from
     Jan Kiszka.

   - intel_idle fix for Intel Ivy Town residency targets from Len Brown.

   - turbostat updates (Intel Broadwell support and output cleanups)
     from Len Brown.

   - New cpuidle sysfs attribute for exporting C-states' target
     residency information to user space from Daniel Lezcano.

   - New kernel command line argument to prevent power domains enabled
     by the bootloader from being turned off even if they are not in use
     (for diagnostics purposes) from Tushar Behera.

   - Fixes for wakeup sysfs attributes documentation from Geert
     Uytterhoeven.

   - New ACPI video blacklist entry for ThinkPad Helix from Stephen
     Chandler Paul.

   - Assorted ACPI cleanups and a Kconfig help update from Jonghwan
     Choi, Zhihui Zhang, Hanjun Guo"

* tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
  ACPI: Update the ACPI spec information in Kconfig
  arm, kvm: fix double lock on cpu_add_remove_lock
  cpuidle: sysfs: Export target residency information
  cpufreq: ppc: Remove duplicate inclusion of fsl_soc.h
  cpufreq: create another field .flags in cpufreq_frequency_table
  cpufreq: use kzalloc() to allocate memory for cpufreq_frequency_table
  cpufreq: don't print value of .driver_data from core
  cpufreq: ia64: don't set .driver_data to index
  cpufreq: powernv: Select CPUFreq related Kconfig options for powernv
  cpufreq: powernv: Use cpufreq_frequency_table.driver_data to store pstate ids
  cpufreq: powernv: cpufreq driver for powernv platform
  cpufreq: at32ap: don't declare local variable as static
  cpufreq: loongson2_cpufreq: don't declare local variable as static
  cpufreq: unicore32: fix typo issue for 'clk'
  cpufreq: exynos: Disable on multiplatform build
  PM / wakeup: Correct presence vs. emptiness of wakeup_* attributes
  PM / domains: Add pd_ignore_unused to keep power domains enabled
  ACPI / dock: Drop dock_device_ids[] table
  ACPI / video: Favor native backlight interface for ThinkPad Helix
  ACPI / thermal: Fix wrong variable usage in debug statement
  ...

Pullx86 core platform updates from Peter Anvin:
 "This is the x86/platform branch with the objectionable IOSF patches
  removed.

  What is left is proper memory handling for Intel GPUs, and a change to
  the Calgary IOMMU code which will be required to make kexec work
  sanely on those platforms after some upcoming kexec changes"

* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, calgary: Use 8M TCE table size by default
  x86/gpu: Print the Intel graphics stolen memory range
  x86/gpu: Add Intel graphics stolen memory quirk for gen2 platforms
  x86/gpu: Add vfunc for Intel graphics stolen memory base address

Pull x86 fixes from Peter Anvin:
 "This is a collection of minor fixes for x86, plus the IRET information
  leak fix (forbid the use of 16-bit segments in 64-bit mode)"

NOTE! We may have to relax the "forbid the use of 16-bit segments in
64-bit mode" part, since there may be people who still run and depend on
16-bit Windows binaries under Wine.

But I'm taking this in the current unconditional form for now to see who
(if anybody) screams bloody murder.  Maybe nobody cares.  And maybe
we'll have to update it with some kind of runtime enablement (like our
vm.mmap_min_addr tunable that people who run dosemu/qemu/wine already
need to tweak).

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86-64, modify_ldt: Ban 16-bit segments on 64-bit kernels
  efi: Pass correct file handle to efi_file_{read,close}
  x86/efi: Correct EFI boot stub use of code32_start
  x86/efi: Fix boot failure with EFI stub
  x86/platform/hyperv: Handle VMBUS driver being a module
  x86/apic: Reinstate error IRQ Pentium erratum 3AP workaround
  x86, CMCI: Add proper detection of end of CMCI storms

Pull second set of ARM changes from Russell King:
 "This is the remainder of the ARM changes for this merge window.
  Included in this request are:

   - fixes for kprobes for big-endian support
   - fix tracing in soft_restart
   - avoid phys address overflow in kdump code
   - fix reporting of read-only pmd bits in kernel page table dump
   - remove unnecessary (and possibly buggy) call to outer_flush_all()
   - fix a three sparse warnings (missing header file for function
     prototypes)
   - fix pj4 crashing single zImage (thanks to arm-soc merging changes
     which enables this with knowledge that the corresponding fix had
     not even been submitted for my tree before the merge window opened)
   - vfp macro cleanups
   - dump register state on undefined instruction userspace faults when
     debugging"

* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  Dump the registers on undefined instruction userspace faults
  ARM: 8018/1: Add {inc,dec}_preempt_count asm macros
  ARM: 8017/1: Move asm macro get_thread_info to asm/assembler.h
  ARM: 8016/1: Check cpu id in pj4_cp0_init.
  ARM: 8015/1: Add cpu_is_pj4 to distinguish PJ4 because it has some differences with V7
  ARM: add missing system_misc.h include to process.c
  ARM: 8009/1: dcscb.c: remove call to outer_flush_all()
  ARM: 8014/1: mm: fix reporting of read-only PMD bits
  ARM: 8012/1: kdump: Avoid overflow when converting pfn to physaddr
  ARM: 8010/1: avoid tracers in soft_restart
  ARM: kprobes-test: Workaround GAS .align bug
  ARM: kprobes-test: use <asm/opcodes.h> for Thumb instruction building
  ARM: kprobes-test: use <asm/opcodes.h> for ARM instruction building
  ARM: kprobes-test: use <asm/opcodes.h> for instruction accesses
  ARM: probes: fix instruction fetch order with <asm/opcodes.h>

Pull Microblaze updates from Michal Simek:
 - use asm-generic/io.h and fix intc/timer code
 - clean platform handling
 - enable some syscalls

* tag 'microblaze-3.15-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Use asm-generic/io.h
  microblaze: Remove platform folder
  microblaze: Remove generic platform
  microblaze: Sort Kconfig options
  microblaze: Move DTS file to common location at boot/dts folder
  microblaze: Fix compilation failure because of release_thread
  microblaze: Fix sparse warning because of missing cpu.h header
  microblaze: Make timer driver endian aware
  microblaze: Make intc driver endian aware
  microblaze: Wire-up new system calls sched_setattr/getattr
  microblaze: Wire-up preadv/pwritev in syscall table
  microblaze: Enable pselect6 syscall
  microblaze: Drop architecture-specific declaration of early_printk
  microblaze: Rename global function heartbeat()

The IRET instruction, when returning to a 16-bit segment, only
restores the bottom 16 bits of the user space stack pointer.  We have
a software workaround for that ("espfix") for the 32-bit kernel, but
it relies on a nonzero stack segment base which is not available in
32-bit mode.

Since 16-bit support is somewhat crippled anyway on a 64-bit kernel
(no V86 mode), and most (if not quite all) 64-bit processors support
virtualization for the users who really need it, simply reject
attempts at creating a 16-bit segment when running on top of a 64-bit
kernel.

Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/n/tip-kicdm89kzw9lldryb1br9od0@git.kernel.org
Cc: <stable@vger.kernel.org>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent

Pull EFI fixes from Matt Fleming:

"* Fix EFI boot regression introduced during the merge window where the
   firmware was reading random values from the stack because we were
   passing a pointer to the wrong object type.

 * Kernel corruption has been reported when booting with the EFI boot
   stub which was tracked down to setting a bogus value for
   bp->hdr.code32_start, resulting in corruption during relocation.

 * Olivier Martin reported that the wrong file handles were being passed
   to efi_file_(read|close), which works for x86 by luck due to the way
   that the FAT driver is implemented, but doesn't work on ARM."
Signed-off-by: Ingo Molnar <mingo@kernel.org>

New kexec-tools wants to pass kdump kernel needed memmap via E820
directly, instead of memmap=exactmap. This makes saved_max_pfn not
be passed down to 2nd kernel. To keep 1st kernel and 2nd kernel using
the same TCE table size, Muli suggest to hard code the size to max (8M).

We can't get rid of saved_max_pfn this time, for backward compatibility
with old first kernel and new second kernel. However new first kernel
and old second kernel can not work unfortunately.

v2->v1:
- retain saved_max_pfn so new 2nd kernel can work with old 1st kernel
  from Vivek
Signed-off-by: WANG Chao <chaowang@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Muli Ben-Yehuda <mulix@mulix.org>
Acked-by: Jon Mason <jdmason@kudzu.us>
Link: http://lkml.kernel.org/r/1394463120-26999-1-git-send-email-chaowang@redhat.comSigned-off-by: H. Peter Anvin <hpa@linux.intel.com>

Merge remote-tracking branches 'spi/fix/complete', 'spi/fix/efm32', 'spi/fix/omap2-mcspi' and 'spi/fix/qup' into spi-linus

spi: Updates for v3.15

A busy release for both cleanups and new drivers this time along with
further factoring out of replicated code into the core:

 - Provide support in the core for DMA mapping transfers - essentially
   all drivers weren't implementing this properly, now there's no
   excuse.
 - Dual and quad mode support for spidev.
 - Fix handling of cs_change in the generic implementation.
 - Remove the S3C_DMA code from the s3c64xx driver now that all the
   platforms using it have been converted to dmaengine.
 - Lots of improvements to the Renesas SPI controllers.
 - Drivers for Allwinner A10 and A31, Qualcomm QUP and Xylinx xtfpga.
 - Removal of the bitrotted ti-ssp driver.

# gpg: Signature made Mon 31 Mar 2014 12:03:09 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg:                 aka "Mark Brown <broonie@debian.org>"
# gpg:                 aka "Mark Brown <broonie@kernel.org>"
# gpg:                 aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg:                 aka "Mark Brown <broonie@linaro.org>"
# gpg:                 aka "Mark Brown <Mark.Brown@linaro.org>"

Merge remote-tracking branches 'regulator/fix/bcm590xx', 'regulator/fix/s2m' and 'regulator/fix/s5m8767' into regulator-linus

regulator: Updates for v3.15

This release has lots and lots of small cleanups and fixes in the
regulator subsystem, mainly cleaning up some bad patterns that got
duplicated in DT code, but otherwise very little of note outside
of the scope of the relevant drivers:

 - Support for configuration of the initial state for gpio regulators
   with multi-voltage support.
 - Support for calling regulator_set_voltage() on fixed regulators.
 - New drivers for Broadcom BCM590xx, Freescale pfuze200, Samsung S2MPA01 &
   S2MPS11/4, some PWM controlled regulators found on some ST boards and
   TI TPS65218.

# gpg: Signature made Mon 31 Mar 2014 12:29:14 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg:                 aka "Mark Brown <broonie@debian.org>"
# gpg:                 aka "Mark Brown <broonie@kernel.org>"
# gpg:                 aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg:                 aka "Mark Brown <broonie@linaro.org>"
# gpg:                 aka "Mark Brown <Mark.Brown@linaro.org>"

Fix the macro used to define linear range regulators to include the
number of voltages.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

Pull exofs updates from Boaz Harrosh:
 "Trivial updates to exofs for 3.15-rc1

  Just a few fixes sent by people"

* 'for-linus' of git://git.open-osd.org/linux-open-osd:
  MAINTAINERS: Update email address for bhalevy
  fs: Mark functions as static in exofs/ore_raid.c
  fs: Mark function as static in exofs/super.c

We're currently passing the file handle for the root file system to
efi_file_read() and efi_file_close(), instead of the file handle for the
file we wish to read/close.

While this has worked up until now, it seems that it has only been by
pure luck. Olivier explains,

 "The issue is the UEFI Fat driver might return the same function for
  'fh->read()' and 'h->read()'. While in our case it does not work with
  a different implementation of EFI_SIMPLE_FILE_SYSTEM_PROTOCOL. In our
  case, we return a different pointer when reading a directory and
  reading a file."

Fixing this actually clears up the two functions because we can drop one
of the arguments, and instead only pass a file 'handle' argument.
Reported-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>

code32_start should point at the start of the protected mode code, and
*not* at the beginning of the bzImage. This is much easier to do in
assembly so document that callers of make_boot_params() need to fill out
code32_start.

The fallout from this bug is that we would end up relocating the image
but copying the image at some offset, resulting in what appeared to be
memory corruption.
Reported-by: Thomas Bächler <thomas@archlinux.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>

commit 54b52d87 ("x86/efi: Build our own EFI services pointer
table") introduced a regression because the 64-bit file_size()
implementation passed a pointer to a 32-bit data object, instead of a
pointer to a 64-bit object.

Because the firmware treats the object as 64-bits regardless it was
reading random values from the stack for the upper 32-bits.

This resulted in people being unable to boot their machines, after
seeing the following error messages,

    Failed to get file info size
    Failed to alloc highmem for files
Reported-by: Dzmitry Sledneu <dzmitry.sledneu@gmail.com>
Reported-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>

Pull x86 platform driver updates from Matthew Garrett:
 "Support for the new keyboard features on the Thinkpad Carbon, a bunch
  of updates for the Sony and Toshiba drivers, a new driver for upcoming
  Alienware hardware and a few misc fixes.  There's a couple of patches
  that got Acked today but aren't invasive, so I'll send a further PR
  for them next week"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (28 commits)
  alienware-wmi: cover some scenarios where memory allocations would fail
  Add WMI driver for controlling AlienFX features on some Alienware products
  fujitsu-tablet: add support for Lifebook T901 and T902
  x86, platform: Make HP_WIRELESS option text more descriptive
  x86, acpi: LLVMLinux: Remove nested functions from Thinkpad ACPI
  save and restore adaptive keyboard mode for suspend and,resume
  support Thinkpad X1 Carbon 2nd generation's adaptive keyboard
  toshiba_acpi: Fix whitespace
  toshiba_acpi: Update version and copyright info
  toshiba_acpi: Add accelerometer support
  toshiba_acpi: Add ECO mode led support
  toshiba_acpi: Add touchpad enable/disable support-
  toshiba_acpi: Add keyboard backlight support
  toshiba_acpi: Adapt Illumination code to use SCI
  toshiba_acpi: Add System Configuration Interface
  thinkpad_acpi: Fix inconsistent mute LED after resume
  sonypi: Simplify dependencies
  Revert "X86 platform: New BayTrail IOSF-SB MBI driver"
  sony-laptop: remove useless sony-laptop versioning
  sony-laptop: add smart connect control function
  ...

Pull block layer fixes from Jens Axboe:
 "A small collection of fixes that should go in before -rc1.  The pull
  request contains:

   - A two patch fix for a regression with block enabled tagging caused
     by a commit in the initial pull request.  One patch is from Martin
     and ensures that SCSI doesn't truncate 64-bit block flags, the
     other one is from me and prevents us from double using struct
     request queuelist for both completion and busy tags.  This caused
     anything from a boot crash for some, to crashes under load.

   - A blk-mq fix for a potential soft stall when hot unplugging CPUs
     with busy IO.

   - percpu_counter fix is listed in here, that caused a suspend issue
     with virtio-blk due to percpu counters having an inconsistent state
     during CPU removal.  Andrew sent this in separately a few days ago,
     but it's here.  JFYI.

   - A few fixes for block integrity from Martin.

   - A ratelimit fix for loop from Mike Galbraith, to avoid spewing too
     much in error cases"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: fix regression with block enabled tagging
  scsi: Make sure cmd_flags are 64-bit
  block: Ensure we only enable integrity metadata for reads and writes
  block: Fix integrity verification
  block: Fix for_each_bvec()
  drivers/block/loop.c: ratelimit error messages
  blk-mq: fix potential stall during CPU unplug with IO pending
  percpu_counter: fix bad counter state during suspend

Pull sound fixes from Takashi Iwai:
 "Here is a bunch of small fixes that have been collected since the
  previous pull request.  In addition to various misc fixes, the
  following are included:

   - HD-audio quirks for Dell, HP, Chromebook, and ALC28x codecs
   - HD-audio AMD HDMI regression fix
   - Continued PM support/fixes for ice1712 driver
   - Multiplatform fixes for ASoC samsung drivers
   - Addition of device id tables to a few ASoC drivers
   - Bit clock polarity config and error flag fixes in ASoC fsl_sai"

* tag 'sound-fix-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (32 commits)
  ALSA: usb-audio: Suppress repetitive debug messages from retire_playback_urb()
  ALSA: hda - Make full_reset boolean
  ALSA: hda - add headset mic detect quirk for a Dell laptop
  sound: dmasound: use module_platform_driver_probe()
  ALSA: au1x00: use module_platform_driver()
  ALSA: hda - Use runtime helper to check active state.
  ALSA: ice1712: Fix boundary checks in PCM pointer ops
  ASoC: davinci-mcasp: Fix bit clock polarity settings
  ASoC: samsung: Fix build on multiplatform
  ASoC: fsl_sai: Fix Bit Clock Polarity configurations
  ALSA: hda - Do not assign streams in reverse order
  ALSA: hda/realtek - Add eapd shutup to ALC283
  ALSA: hda/realtek - Change model name alias for ChromeOS
  ASoC: da732x: Print correct major id
  ALSA: hda/realtek - Improve HP depop when system change power state on Chromebook
  ASoC: cs42l52: Fix mask for REVID
  sound/oss: Remove uncompilable DBG macro use
  ALSA: ice1712: Save/restore routing and rate registers
  ALSA: ice1712: restore AK4xxx volumes on resume
  ASoC: alc56(23|32): fix undefined return value of probing code
  ...

Pull thermal management updates from Zhang Rui:
 "We only have a couple of fixes/cleanups for platform thermal drivers
  this time.

  Specifics:

   - rcar thermal driver: avoid updating the thermal zone in case an IRQ
     was triggered but the temperature didn't effectively change.  From
     Patrick Titiano.

   - update the imx thermal driver' formula of converting thermal
     sensor' raw date to real temperature in degree C.  From Anson
     Huang.

   - trivial code cleanups of ti soc thermal and rcar thermal driver
     from Jingoo Han and Patrick Titiano"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: rcar-thermal: update thermal zone only when temperature changes
  thermal: rcar-thermal: fix same mask applied twice
  thermal: ti-soc-thermal: Use SIMPLE_DEV_PM_OPS macro
  thermal: imx: update formula for thermal sensor

Intel test builder caught a few instances that should test if kzalloc failed to
allocate memory as well as a scenario that platform_driver wasn't properly
initialized.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

Pull LED updates from Bryan Wu:
 "This cycle we got:
   - new driver for leds-mc13783
   - bug fixes
   - code cleanup"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
  leds: make sure we unregister a trigger only once
  leds: leds-pwm: properly clean up after probe failure
  leds: clevo-mail: Make probe function __init
  leds-ot200: Fix dependencies
  leds-gpio: of: introduce MODULE_DEVICE_TABLE for module autoloading
  leds: clevo-mail: remove __initdata marker
  leds: leds-ss4200: remove __initdata marker
  leds: blinkm: remove unnecessary spaces
  leds: lp5562: remove unnecessary parentheses
  leds: leds-ss4200: remove DEFINE_PCI_DEVICE_TABLE macro
  leds: leds-s3c24xx: Trivial cleanup in header file
  drivers/leds: delete non-required instances of include <linux/init.h>
  leds: leds-gpio: add retain-state-suspended property
  leds: leds-mc13783: Add devicetree support
  leds: leds-mc13783: Remove unnecessary cleaning of registers on exit
  leds: leds-mc13783: Use proper "max_brightness" value fo LEDs
  leds: leds-mc13783: Use LED core PM functions
  leds: leds-mc13783: Add MC34708 LED support
  leds: Turn off led if blinking is disabled
  ledtrig-cpu: Handle CPU hot(un)plugging

Pull slave-dmaengine updates from Vinod Koul:
 - New driver for Qcom bam dma
 - New driver for RCAR peri-peri
 - New driver for FSL eDMA
 - Various odd fixes and updates thru the subsystem

* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
  dmaengine: add Qualcomm BAM dma driver
  shdma: add R-Car Audio DMAC peri peri driver
  dmaengine: sirf: enable generic dt binding for dma channels
  dma: omap-dma: Implement device_slave_caps callback
  dmaengine: qcom_bam_dma: Add device tree binding
  dma: dw: Add suspend and resume handling for PCI mode DW_DMAC.
  dma: dw: allocate memory in two stages in probe
  Add new line to test result strings produced in verbose mode
  dmaengine: pch_dma: use tasklet_kill in teardown
  dmaengine: at_hdmac: use tasklet_kill in teardown
  dma: cppi41: start tear down only if channel is busy
  usb: musb: musb_cppi41: Dont reprogram DMA if tear down is initiated
  dmaengine: s3c24xx-dma: make phy->irq signed for error handling
  dma: imx-dma: Add missing module owner field
  dma: imx-dma: Replace printk with dev_*
  dma: fsl-edma: fix static checker warning of NULL dereference
  dma: Remove comment about embedding dma_slave_config into custom structs
  dma: mmp_tdma: move to generic device tree binding
  dma: mmp_pdma: add IRQF_SHARED when request irq
  dma: edma: Fix memory leak in edma_prep_dma_cyclic()
  ...

Pull backlight changes from Lee Jones:
 - core: call put_device() instead of kfree()
 - gpio-backlight: add DT support
 - lm3639_bl driver: use managed resources

* tag 'backlight-for-linus-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
  backlight: lm3639: Use devm_backlight_device_register()
  backlight: gpio-backlight: Add DT support
  backlight: core: Replace kfree with put_device

Martin reported that his test system would not boot with
current git, it oopsed with this:

BUG: unable to handle kernel paging request at ffff88046c6c9e80
IP: [<ffffffff812971e0>] blk_queue_start_tag+0x90/0x150
PGD 1ddf067 PUD 1de2067 PMD 47fc7d067 PTE 800000046c6c9060
Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: sd_mod lpfc(+) scsi_transport_fc scsi_tgt oracleasm
rpcsec_gss_krb5 ipv6 igb dca i2c_algo_bit i2c_core hwmon
CPU: 3 PID: 87 Comm: kworker/u17:1 Not tainted 3.14.0+ #246
Hardware name: Supermicro X9DRX+-F/X9DRX+-F, BIOS 3.00 07/09/2013
Workqueue: events_unbound async_run_entry_fn
task: ffff8802743c2150 ti: ffff880273d02000 task.ti: ffff880273d02000
RIP: 0010:[<ffffffff812971e0>]  [<ffffffff812971e0>]
blk_queue_start_tag+0x90/0x150
RSP: 0018:ffff880273d03a58  EFLAGS: 00010092
RAX: ffff88046c6c9e78 RBX: ffff880077208e78 RCX: 00000000fffc8da6
RDX: 00000000fffc186d RSI: 0000000000000009 RDI: 00000000fffc8d9d
RBP: ffff880273d03a88 R08: 0000000000000001 R09: ffff8800021c2410
R10: 0000000000000005 R11: 0000000000015b30 R12: ffff88046c5bb8a0
R13: ffff88046c5c0890 R14: 000000000000001e R15: 000000000000001e
FS:  0000000000000000(0000) GS:ffff880277b00000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff88046c6c9e80 CR3: 00000000018f6000 CR4: 00000000000407e0
Stack:
 ffff880273d03a98 ffff880474b18800 0000000000000000 ffff880474157000
 ffff88046c5c0890 ffff880077208e78 ffff880273d03ae8 ffffffff813b9e62
 ffff880200000010 ffff880474b18968 ffff880474b18848 ffff88046c5c0cd8
Call Trace:
 [<ffffffff813b9e62>] scsi_request_fn+0xf2/0x510
 [<ffffffff81293167>] __blk_run_queue+0x37/0x50
 [<ffffffff8129ac43>] blk_execute_rq_nowait+0xb3/0x130
 [<ffffffff8129ad24>] blk_execute_rq+0x64/0xf0
 [<ffffffff8108d2b0>] ? bit_waitqueue+0xd0/0xd0
 [<ffffffff813bba35>] scsi_execute+0xe5/0x180
 [<ffffffff813bbe4a>] scsi_execute_req_flags+0x9a/0x110
 [<ffffffffa01b1304>] sd_spinup_disk+0x94/0x460 [sd_mod]
 [<ffffffff81160000>] ? __unmap_hugepage_range+0x200/0x2f0
 [<ffffffffa01b2b9a>] sd_revalidate_disk+0xaa/0x3f0 [sd_mod]
 [<ffffffffa01b2fb8>] sd_probe_async+0xd8/0x200 [sd_mod]
 [<ffffffff8107703f>] async_run_entry_fn+0x3f/0x140
 [<ffffffff8106a1c5>] process_one_work+0x175/0x410
 [<ffffffff8106b373>] worker_thread+0x123/0x400
 [<ffffffff8106b250>] ? manage_workers+0x160/0x160
 [<ffffffff8107104e>] kthread+0xce/0xf0
 [<ffffffff81070f80>] ? kthread_freezable_should_stop+0x70/0x70
 [<ffffffff815f0bac>] ret_from_fork+0x7c/0xb0
 [<ffffffff81070f80>] ? kthread_freezable_should_stop+0x70/0x70
Code: 48 0f ab 11 72 db 48 81 4b 40 00 00 10 00 89 83 08 01 00 00 48 89
df 49 8b 04 24 48 89 1c d0 e8 f7 a8 ff ff 49 8b 85 28 05 00 00 <48> 89
58 08 48 89 03 49 8d 85 28 05 00 00 48 89 43 08 49 89 9d
RIP  [<ffffffff812971e0>] blk_queue_start_tag+0x90/0x150
 RSP <ffff880273d03a58>
CR2: ffff88046c6c9e80

Martin bisected and found this to be the problem patch;

	commit 6d113398
	Author: Jan Kara <jack@suse.cz>
	Date:   Mon Feb 24 16:39:54 2014 +0100

	    block: Stop abusing rq->csd.list in blk-softirq

and the problem was immediately apparent. The patch states that
it is safe to reuse queuelist at completion time, since it is
no longer used. However, that is not true if a device is using
block enabled tagging. If that is the case, then the queuelist
is reused to keep track of busy tags. If a device also ended
up using softirq completions, we'd reuse ->queuelist for the
IPI handling while block tagging was still using it. Boom.

Fix this by adding a new ipi_list list head, and share the
memory used with the request hash table. The hash table is
never used after the request is moved to the dispatch list,
which happens long before any potential completion of the
request. Add a new request bit for this, so we don't have
cases that check rq->hash while it could potentially have
been reused for the IPI completion.
Reported-by: Martin K. Petersen <martin.petersen@oracle.com>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jens Axboe <axboe@fb.com>

cmd_flags in struct request is now 64 bits wide but the scsi_execute
functions truncated arguments passed to int leading to errors. Make sure
the flags parameters are u64.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Jens Axboe <axboe@fb.com>
CC: Jan Kara <jack@suse.cz>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>

BugLink: http://bugs.launchpad.net/bugs/1305133

Malfunctioning or slow devices can cause a flood of dmesg SPAM.

I've ignored checkpatch.pl complaints about the use of printk_ratelimit() in favour
of prior art in sound/usb/pcm.c.

WARNING: Prefer printk_ratelimited or pr_<level>_ratelimited to printk_ratelimit
+	if (printk_ratelimit() &&

Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Eldad Zack <eldad@fogrefinery.com>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-v3.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v3.15

A smattering of device specific fixes, nothing stands out here except
for the multiplatform fixes for Samsung and the device IDs being added
by Stephen Warren - there's no real code changes from those and they
give better robustness to the enumeration with DT.

Pull i2c updates from Wolfram Sang:
 "Here is the pull request from the i2c subsystem.  It got a little
  delayed because I needed to wait for a dependency to be included
  (commit b424080a: "reset: Add optional resets and stubs").  Plus,
  I had some email problems.  All done now, the highlights are:

   - drivers can now deprecate their use of i2c classes.  That shouldn't
     be used on embedded platforms anyhow and was often blindly
     copy&pasted.  This mechanism gives users time to switch away and
     ultimately boot faster once the use of classes for those drivers is
     gone for good.

   - new drivers for QUP, Cadence, efm32

   - tracepoint support for I2C and SMBus

   - bigger cleanups for the mv64xxx, nomadik, and designware drivers

  And the usual bugfixes, cleanups, feature additions.  Most stuff has
  been in linux-next for a while.  Just some hot fixes and new drivers
  were added a bit more recently."

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (63 commits)
  i2c: cadence: fix Kconfig dependency
  i2c: Add driver for Cadence I2C controller
  i2c: cadence: Document device tree bindings
  Documentation: i2c: improve section about flags mangling the protocol
  i2c: qup: use proper type fro clk_freq
  i2c: qup: off by ones in qup_i2c_probe()
  i2c: efm32: fix binding doc
  MAINTAINERS: update I2C web resources
  i2c: qup: New bus driver for the Qualcomm QUP I2C controller
  i2c: qup: Add device tree bindings information
  i2c: i2c-xiic: deprecate class based instantiation
  i2c: i2c-sirf: deprecate class based instantiation
  i2c: i2c-mv64xxx: deprecate class based instantiation
  i2c: i2c-designware-platdrv: deprecate class based instantiation
  i2c: i2c-davinci: deprecate class based instantiation
  i2c: i2c-bcm2835: deprecate class based instantiation
  i2c: mv64xxx: Fix reset controller handling
  i2c: omap: fix usage of IS_ERR_VALUE with pm_runtime_get_sync
  i2c: efm32: new bus driver
  i2c: exynos5: remove unnecessary cast of void pointer
  ...

Pull MMC updates from Chris Ball:
 "MMC highlights for 3.15:

  Core:
   - CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
   - DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
   - Add GPIO descriptor based slot-gpio card detect API

  Drivers:
   - dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
   - mmci: Support HW busy detection on ux500
   - omap: Support MMC_ERASE
   - omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
   - rtsx: Support pre-req/post-req async
   - sdhci: Add support for Realtek RTS5250 controllers
   - sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
   - sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
   - sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"

* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
  mmc: sdhci-acpi: Intel SDIO has broken card detect
  mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
  mmc: sdhci-msm: Add platform_execute_tuning implementation
  mmc: sdhci-msm: Initial support for Qualcomm chipsets
  mmc: sdhci-msm: Qualcomm SDHCI binding documentation
  sdhci: only reprogram retuning timer when flag is set
  mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
  mmc: sdhci: Allow for irq being shared
  mmc: sdhci-acpi: Add device id 80860F16
  mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
  mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
  mmc: slot-gpio: Split out CD IRQ request into a separate function
  mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
  Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
  mmc: sdhci-spear: use generic card detection gpio support
  mmc: sdhci-spear: remove support for power gpio
  mmc: sdhci-spear: simplify resource handling
  mmc: sdhci-spear: fix platform_data usage
  mmc: sdhci-spear: fix error handling paths for DT
  mmc: sdhci-bcm-kona: fix build errors when built-in
  ...

Pull more powerpc updates from Ben Herrenschmidt:
 "Here are a few more powerpc things for you.

  So you'll find here the conversion of the two new firmware sysfs
  interfaces to the new API for self-removing files that Greg and Tejun
  introduced, so they can finally remove the old one.

  I'm also reverting the hwmon driver for powernv.  I shouldn't have
  merged it, I got a bit carried away here.  I hadn't realized it was
  never CCed to the relevant maintainer(s) and list(s), and happens to
  have some issues so I'm taking it out and it will come back via the
  proper channels.

  The rest is a bunch of LE fixes (argh, some of the new stuff was
  broken on LE, I really need to start testing LE myself !) and various
  random fixes here and there.

  Finally one bit that's not strictly a fix, which is the HVC OPAL
  change to "kick" the HVC thread when the firmware tells us there is
  new incoming data.  I don't feel like waiting for this one, it's
  simple enough, and it makes a big difference in console responsiveness
  which is good for my nerves"

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (26 commits)
  powerpc/powernv Adapt opal-elog and opal-dump to new sysfs_remove_file_self
  Revert "powerpc/powernv: hwmon driver for power values, fan rpm and temperature"
  power, sched: stop updating inside arch_update_cpu_topology() when nothing to be update
  powerpc/le: Avoid creatng R_PPC64_TOCSAVE relocations for modules.
  arch/powerpc: Use RCU_INIT_POINTER(x, NULL) in platforms/cell/spu_syscalls.c
  powerpc/opal: Add missing include
  powerpc: Convert last uses of __FUNCTION__ to __func__
  powerpc: Add lq/stq emulation
  powerpc/powernv: Add invalid OPAL call
  powerpc/powernv: Add OPAL message log interface
  powerpc/book3s: Fix mc_recoverable_range buffer overrun issue.
  powerpc: Remove dead code in sycall entry
  powerpc: Use of_node_init() for the fakenode in msi_bitmap.c
  powerpc/mm: NUMA pte should be handled via slow path in get_user_pages_fast()
  powerpc/powernv: Fix endian issues with sensor code
  powerpc/powernv: Fix endian issues with OPAL async code
  tty/hvc_opal: Kick the HVC thread on OPAL console events
  powerpc/powernv: Add opal_notifier_unregister() and export to modules
  powerpc/ppc64: Do not turn AIL (reloc-on interrupts) too early
  powerpc/ppc64: Gracefully handle early interrupts
  ...

Jan Stancek reported:
 "pthread_cond_broadcast/4-1.c testcase from openposix testsuite (LTP)
  occasionally fails, because some threads fail to wake up.

  Testcase creates 5 threads, which are all waiting on same condition.
  Main thread then calls pthread_cond_broadcast() without holding mutex,
  which calls:

      futex(uaddr1, FUTEX_CMP_REQUEUE_PRIVATE, 1, 2147483647, uaddr2, ..)

  This immediately wakes up single thread A, which unlocks mutex and
  tries to wake up another thread:

      futex(uaddr2, FUTEX_WAKE_PRIVATE, 1)

  If thread A manages to call futex_wake() before any waiters are
  requeued for uaddr2, no other thread is woken up"

The ordering constraints for the hash bucket waiter counting are that
the waiter counts have to be incremented _before_ getting the spinlock
(because the spinlock acts as part of the memory barrier), but the
"requeue" operation didn't honor those rules, and nobody had even
thought about that case.

This fairly simple patch just increments the waiter count for the target
hash bucket (hb2) when requeing a futex before taking the locks.  It
then decrements them again after releasing the lock - the code that
actually moves the futex(es) between hash buckets will do the additional
required waiter count housekeeping.
Reported-and-tested-by: Jan Stancek <jstancek@redhat.com>
Acked-by: Davidlohr Bueso <davidlohr@hp.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # 3.14
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>