- 06 Aug, 2020 40 commits
-
-
George Shen authored
[Why] During SetPathMode and UpdatePlanes, the plane state can be null. We default to linear swizzle mode when plane state is null. This resulted in bandwidth validation failing when trying to set 8K60 mode (which previously passed validation during rebuild timing list). [How] Change the default swizzle mode from linear to 4kb_s and update pitch accordingly. Signed-off-by:
George Shen <george.shen@amd.com> Reviewed-by:
Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by:
Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
JinZe.Xu authored
[How] Use dc_is_hdmi_signal to determine signal type. Signed-off-by:
JinZe.Xu <JinZe.Xu@amd.com> Reviewed-by:
Charlene Liu <Charlene.Liu@amd.com> Acked-by:
-
Aric Cyr authored
[Why] Sink OUI supported cap is not set so driver skips programming it. [How] Revert the change the skips OUI programming if the cap is not set Signed-off-by:
Aric Cyr <aric.cyr@amd.com> Reviewed-by:
Anthony Koo <Anthony.Koo@amd.com> Acked-by:
-
Harry Wentland authored
[Why&How] use correct logger context Signed-off-by:
Harry Wentland <harry.wentland@amd.com> Reviewed-by:
Roman Li <Roman.Li@amd.com> Acked-by:
-
Dmytro Laktyushkin authored
Signed-off-by:
Eric Bernstein <Eric.Bernstein@amd.com> Acked-by:
-
Igor Kravchenko authored
[Why] For ver.4.4 and higher VBIOS contains default setting table. {How] Read Golden Settings Table from VBIOS, apply Aux tuning parameters. Signed-off-by:Igor Kravchenko <Igor.Kravchenko@amd.com> Reviewed-by:
-
Eric Bernstein authored
Signed-off-by:
Chris Park <Chris.Park@amd.com> Acked-by:
-
Jiansong Chen authored
Enable GFXOFF for navy_flounder. Signed-off-by:
Jiansong Chen <Jiansong.Chen@amd.com> Reviewed-by:
Likun Gao <Likun.Gao@amd.com> Signed-off-by:
-
Liu ChengZhe authored
1. For Navi12, CHIP_SIENNA_CICHLID, skip tmr load operation; 2. Check pointer before release firmware. v2: use CHIP_SIENNA_CICHLID instead v3: remove local "bool ret"; fix grammer issue v4: use my name instead of "root" v5: fix grammer issue and indent issue Signed-off-by:
Liu ChengZhe <ChengZhe.Liu@amd.com> Reviewed-by:
Luben Tuikov <luben.tuikov@amd.com> Signed-off-by:
-
Liu ChengZhe authored
Assigning false to block->status.hw overwrites PSP's previous hardware status, which causes the PSP to Resume operation after hardware init. Remove this assignment and let the PSP execute Resume operation when it is told to. v2: Remove the braces. v3: Modify the description. Signed-off-by:
-
Jiansong Chen authored
Update GC golden setting for navy_flounder. Signed-off-by:
Tao Zhou <tao.zhou1@amd.com> Signed-off-by:
-
Jiansong Chen authored
It's in accordance with pmfw 65.5.0 for navy_flounder. Signed-off-by:
Kenneth Feng <kenneth.feng@amd.com> Signed-off-by:
-
Huang Rui authored
It doesn't expose PPTable descriptor on APU platform. So max/min temperature values cannot be got from APU platform. v2: Stoney needs to skip crit temperature as well. Signed-off-by:
Huang Rui <ray.huang@amd.com> Reviewed-by:
Kevin Wang <kevin1.wang@amd.com> Signed-off-by:
-
Aric Cyr authored
[Why] Test expects that we also read HPD_IRQ_VECTOR when checking for symbol loss as well lane status. [How] Read bytes 0x200-0x205 instead of just 0x202-0x205 Signed-off-by:
Jun Lei <Jun.Lei@amd.com> Acked-by:
Eryk Brol <eryk.brol@amd.com> Signed-off-by:
-
Wyatt Wood authored
[Why] Feature requires synchronization of dig, pipe, and cursor locking between driver and fw. [How] Set flag to force psr to use hw lock mgr. Signed-off-by:
Wyatt Wood <wyatt.wood@amd.com> Reviewed-by:
-
hersen wu authored
[Why] ramp_up_dispclk_with_dpp is to change dispclk, dppclk and dprefclk according to bandwidth requirement. call stack: rv1_update_clocks --> update_clocks --> dcn10_prepare_bandwidth / dcn10_optimize_bandwidth --> prepare_bandwidth / optimize_bandwidth. before change dcn hw, prepare_bandwidth will be called first to allow enough clock, watermark for change, after end of dcn hw change, optimize_bandwidth is executed to lower clock to save power for new dcn hw settings. below is sequence of commit_planes_for_stream: step 1: prepare_bandwidth - raise clock to have enough bandwidth step 2: lock_doublebuffer_enable step 3: pipe_control_lock(true) - make dchubp register change will not take effect right way step 4: apply_ctx_for_surface - program dchubp step 5: pipe_control_lock(false) - dchubp register change take effect step 6: optimize_bandwidth --> dc_post_update_surfaces_to_stream for full_date, optimize clock to save power at end of step 1, dcn clocks (dprefclk, dispclk, dppclk) may be changed for new dchubp configuration. but real dcn hub dchubps are still running with old configuration until end of step 5. this need clocks settings at step 1 should not less than that before step 1. this is checked by two conditions: 1. if (should_set_clock(safe_to_lower , new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz) || new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz) 2. request_dpp_div = new_clocks->dispclk_khz > new_clocks->dppclk_khz the second condition is based on new dchubp configuration. dppclk for new dchubp may be different from dppclk before step 1. for example, before step 1, dchubps are as below: pipe 0: recout=(0,40,1920,980) viewport=(0,0,1920,979) pipe 1: recout=(0,0,1920,1080) viewport=(0,0,1920,1080) for dppclk for pipe0 need dppclk = dispclk new dchubp pipe split configuration: pipe 0: recout=(0,0,960,1080) viewport=(0,0,960,1080) pipe 1: recout=(960,0,960,1080) viewport=(960,0,960,1080) dppclk only needs dppclk = dispclk /2. dispclk, dppclk are not lock by otg master lock. they take effect after step 1. during this transition, dispclk are the same, but dppclk is changed to half of previous clock for old dchubp configuration between step 1 and step 6. This may cause p-state warning intermittently. [How] for new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz, we need make sure dppclk are not changed to less between step 1 and 6. for new_clocks->dispclk_khz > clk_mgr_base->clks.dispclk_khz, new display clock is raised, but we do not know ratio of new_clocks->dispclk_khz and clk_mgr_base->clks.dispclk_khz, new_clocks->dispclk_khz /2 does not guarantee equal or higher than old dppclk. we could ignore power saving different between dppclk = displck and dppclk = dispclk / 2 between step 1 and step 6. as long as safe_to_lower = false, set dpclk = dispclk to simplify condition check. CC: Stable <stable@vger.kernel.org> Signed-off-by:
Hersen Wu <hersenxs.wu@amd.com> Reviewed-by:
-
Reza Amini authored
[Why] Each asic can optimize best based on its capabilities [How] Optimizing timing for a new pixel clock Signed-off-by:
Reza Amini <Reza.Amini@amd.com> Reviewed-by:
-
Jun Lei authored
[Why] Programming DCN is explicitly forbidden during idle optimzations allowed state. Existing implemenation relies on OS/DM, which is not robust. Instead DC should sequence this. Note that DC will not re-enter idle optimized state on its own, it is only responsible for catching out of sequence calls. It is still DM responsibility to sequence appropriate for optimized power, but this change removes the requirement for DM to cover the .1% case. [How] - elevate updates during idle optimized state to full updates - disable idle power optimizations prior to programming Signed-off-by:
-
Stylon Wang authored
[Why] Setting abm level does not correctly update CRTC state. As a result no surface update is added to dc stream state and triggers warning. [How] Correctly update CRTC state when setting abm level property. CC: Stable <stable@vger.kernel.org> Signed-off-by:
Stylon Wang <stylon.wang@amd.com> Reviewed-by:
Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by:
-
Bhawanpreet Lakha authored
Use DCN21 functions instead of DCE110 Signed-off-by:
Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by:
-
Bhawanpreet Lakha authored
[Why] Currently navy_flounder is using sienna_cichlid_dmcub.bin. [How] Create a seperate define so navy_flounder will use its own firmware. Signed-off-by:
-
Martin Tsai authored
[Why] Some monitors could suffer symbol unlock but cannot send HPD IRQ to notic source device to handle link loss. This makes monitor stuck in abnormal status and causes black screen. [How] According to the suggestion from scalar vendor, to check lane status again after link training done. That can improve the comaptibility from current production monitors. Signed-off-by:
Martin Tsai <martin.tsai@amd.com> Reviewed-by:
-
Alvin Lee authored
[Why] In dcn3_update_clocks there are situations where dppclk is not lowered (i.e. stays the same), but DTO still needs to be increased before we program pipe frontend (i.e. in prepare_bandwidth). If we don't program the new DTO value before we program the pipe, we will underflow as soon as the pipe lock is released until the next call to dcn3_update_clocks where the DTO is updated. [How] Remove dppclk check before programming new DTO value. Signed-off-by:
Alvin Lee <alvin.lee2@amd.com> Reviewed-by:
-
Eryk Brol authored
[why] Fix naming and return bits rather than bytes per pixel for naming consistency. Because registers return Bytes per pixel, but DSC Config structure is expecting bits per pixel as input. So when returning the value convert from bytes into bits. Signed-off-by:
Mikita Lipski <mikita.lipski@amd.com> Reviewed-by:
-
Eryk Brol authored
[Why] Struct dcn_dsc_state is used for reading current state and parameters of DSC on a pipe, the target rate parameter uses bytes per pixel even though its reading BITS_PER_PIXEL register. [How] Changing it to Bits Per Pixel for consistency. Signed-off-by:
-
Dmytro Laktyushkin authored
[Why] This change replaces older looping code in favor of these functions. [How] There are built in functions for extracting global sync params during mode validation now. Signed-off-by:
-
Kevin Wang authored
1. allow asic to handle sensor type by itself. 2. if not, use smu common sensor to handle it. Signed-off-by:
-
Dan Carpenter authored
These tables have _COUNT number of elements so the comparisons should be >= instead of > to prevent reading one element beyond the end of the array. Fixes: 8264ee69 ("drm/amd/powerplay: drop unused code") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Likun Gao authored
Update sienna_cichlid driver if header and related files. Support new smu metrics for pre & postDS frequency. Signed-off-by:
-
Changfeng authored
Take back patch:drop unnecessary message support check Because the gpu reset fail problem on renoir can be fixed by: drm/amd/powerplay: skip invalid msg when smu set mp1 state It needs to remove SWSMU_CODE_LAYER_L1 in smu_cmn.h to guard a clear code layer. Signed-off-by:
changfeng <Changfeng.Zhu@amd.com> Reviewed-by:
Evan Quan <evan.quan@amd.com> Signed-off-by:
-
Boyuan Zhang authored
Signed-off-by:
Boyuan Zhang <boyuan.zhang@amd.com> Reviewed-by:
Leo Liu <leo.liu@amd.com> Signed-off-by:
-
James Zhu authored
jpeg ip block is already selected based on ASIC type during set_ip_blocks. Signed-off-by:
James Zhu <James.Zhu@amd.com> Reviewed-by:
-
Likun Gao authored
Update golden setting for sienna_cichlid. Signed-off-by:
Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by:
-
Likun Gao authored
Set valid_in_vf to false for the message not support in vf mode on sienna cichlid. Signed-off-by:
-
Likun Gao authored
Mapping Mode1Reset message for sienna_cichlid. Signed-off-by:
-
Likun Gao authored
Some asic may not support for some message of set mp1 state. If the return value of smu_send_smc_msg is -EINVAL, that means it failed to send msg to smc as it can not map an valid message for the ASIC. And with that case, smu_set_mp1_state should be skipped as those ASIC was in fact do not support for that. Signed-off-by:
-
Kenneth Feng authored
It's not necessary to retrieve the power features status when the asic is booted up the first time. This patch can have the features enablement status still checked in suspend/resume case and removed from the first boot up sequence. Signed-off-by:
-
Changfeng authored
The below 3 messages are not supported on Renoir SMU_MSG_PrepareMp1ForShutdown SMU_MSG_PrepareMp1ForUnload SMU_MSG_PrepareMp1ForReset It needs to revert patch: drm/amd/powerplay: drop unnecessary message support check to avoid set mp1 state fail during gpu reset on renoir. Signed-off-by:
-
Guchun Chen authored
This will tell users if the faulty page has been written to external eeprom device in dmesg log. Signed-off-by:
Guchun Chen <guchun.chen@amd.com> Reviewed-by:
-
John Clements authored
Added dedicated 64bit reg read/write support Reviewed-by:
John Clements <john.clements@amd.com> Signed-off-by:
-
