Skip to content

L
linux
Switch branch/tag
  1. 10 Jul, 2016 3 commits
    • Lukas Wunner's avatar
      x86/quirks: Add early quirk to reset Apple AirPort card · abb2bafd
      Lukas Wunner authored 
      The EFI firmware on Macs contains a full-fledged network stack for
downloading OS X images from osrecovery.apple.com. Unfortunately
on Macs introduced 2011 and 2012, EFI brings up the Broadcom 4331
wireless card on every boot and leaves it enabled even after
ExitBootServices has been called. The card continues to assert its IRQ
line, causing spurious interrupts if the IRQ is shared. It also corrupts
memory by DMAing received packets, allowing for remote code execution
over the air. This only stops when a driver is loaded for the wireless
card, which may be never if the driver is not installed or blacklisted.

The issue seems to be constrained to the Broadcom 4331. Chris Milsted
has verified that the newer Broadcom 4360 built into the MacBookPro11,3
(2013/2014) does not exhibit this behaviour. The chances that Apple will
ever supply a firmware fix for the older machines appear to be zero.

The solution is to reset the card on boot by writing to a reset bit in
its mmio space. This must be done as an early quirk and not as a plain
vanilla PCI quirk to successfully combat memory corruption by DMAed
packets: Matthew Garrett found out in 2012 that the packets are written
to EfiBootServicesData memory (http://mjg59.dreamwidth.org/11235.html).
This type of memory is made available to the page allocator by
efi_free_boot_services(). Plain vanilla PCI quirks run much later, in
subsys initcall level. In-between a time window would be open for memory
corruption. Random crashes occurring in this time window and attributed
to DMAed packets have indeed been observed in the wild by Chris
Bainbridge.

When Matthew Garrett analyzed the memory corruption issue in 2012, he
sought to fix it with a grub quirk which transitions the card to D3hot:
http://git.savannah.gnu.org/cgit/grub.git/commit/?id=9d34bb85da56

This approach does not help users with other bootloaders and while it
may prevent DMAed packets, it does not cure the spurious interrupts
emanating from the card. Unfortunately the card's mmio space is
inaccessible in D3hot, so to reset it, we have to undo the effect of
Matthew's grub patch and transition the card back to D0.

Note that the quirk takes a few shortcuts to reduce the amount of code:
The size of BAR 0 and the location of the PM capability is identical
on all affected machines and therefore hardcoded. Only the address of
BAR 0 differs between models. Also, it is assumed that the BCMA core
currently mapped is the 802.11 core. The EFI driver seems to always take
care of this.

Michael Büsch, Bjorn Helgaas and Matt Fleming contributed feedback
towards finding the best solution to this problem.

The following should be a comprehensive list of affected models:
    iMac13,1        2012  21.5"       [Root Port 00:1c.3 = 8086:1e16]
    iMac13,2        2012  27"         [Root Port 00:1c.3 = 8086:1e16]
    Macmini5,1      2011  i5 2.3 GHz  [Root Port 00:1c.1 = 8086:1c12]
    Macmini5,2      2011  i5 2.5 GHz  [Root Port 00:1c.1 = 8086:1c12]
    Macmini5,3      2011  i7 2.0 GHz  [Root Port 00:1c.1 = 8086:1c12]
    Macmini6,1      2012  i5 2.5 GHz  [Root Port 00:1c.1 = 8086:1e12]
    Macmini6,2      2012  i7 2.3 GHz  [Root Port 00:1c.1 = 8086:1e12]
    MacBookPro8,1   2011  13"         [Root Port 00:1c.1 = 8086:1c12]
    MacBookPro8,2   2011  15"         [Root Port 00:1c.1 = 8086:1c12]
    MacBookPro8,3   2011  17"         [Root Port 00:1c.1 = 8086:1c12]
    MacBookPro9,1   2012  15"         [Root Port 00:1c.1 = 8086:1e12]
    MacBookPro9,2   2012  13"         [Root Port 00:1c.1 = 8086:1e12]
    MacBookPro10,1  2012  15"         [Root Port 00:1c.1 = 8086:1e12]
    MacBookPro10,2  2012  13"         [Root Port 00:1c.1 = 8086:1e12]

For posterity, spurious interrupts caused by the Broadcom 4331 wireless
card resulted in splats like this (stacktrace omitted):

    irq 17: nobody cared (try booting with the "irqpoll" option)
    handlers:
    [<ffffffff81374370>] pcie_isr
    [<ffffffffc0704550>] sdhci_irq [sdhci] threaded [<ffffffffc07013c0>] sdhci_thread_irq [sdhci]
    [<ffffffffc0a0b960>] azx_interrupt [snd_hda_codec]
    Disabling IRQ #17

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79301
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111781
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=728916
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=895951#c16
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1009819
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1098621
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1149632#c5
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1279130
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1332732
Tested-by: Konstantin Simanov <k.simanov@stlk.ru>        # [MacBookPro8,1]
Tested-by: Lukas Wunner <lukas@wunner.de>                # [MacBookPro9,1]
Tested-by: Bryan Paradis <bryan.paradis@gmail.com>       # [MacBookPro9,2]
Tested-by: Andrew Worsley <amworsley@gmail.com>          # [MacBookPro10,1]
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com> # [MacBookPro10,2]
Signed-off-by: default avatarLukas Wunner <lukas@wunner.de>
Acked-by: default avatarRafał Miłecki <zajec5@gmail.com>
Acked-by: default avatarMatt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris Milsted <cmilsted@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Michael Buesch <m@bues.ch>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: b43-dev@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: stable@vger.kernel.org # 123456789abc: x86/quirks: Apply nvidia_bugs quirk only on root bus
Cc: stable@vger.kernel.org # 123456789abc: x86/quirks: Reintroduce scanning of secondary buses
Link: http://lkml.kernel.org/r/48d0972ac82a53d460e5fce77a07b2560db95203.1465690253.git.lukas@wunner.de
[ Did minor readability edits. ]
Signed-off-by: default avatarIngo Molnar <mingo@kernel.org>
      abb2bafd
    • Lukas Wunner's avatar
      x86/quirks: Reintroduce scanning of secondary buses · 850c3210
      Lukas Wunner authored 
      We used to scan secondary buses until the following commit that
was applied in 2009:

  8659c406 ("x86: only scan the root bus in early PCI quirks")

which commit constrained early quirks to the root bus only. Its
motivation was to prevent application of the nvidia_bugs quirk
on secondary buses.

We're about to add a quirk to reset the Broadcom 4331 wireless card on
2011/2012 Macs, which is located on a secondary bus behind a PCIe root
port. To facilitate that, reintroduce scanning of secondary buses.

The commit message of 8659c406 notes that scanning only the root bus
"saves quite some unnecessary scanning work". The algorithm used prior
to 8659c406 was particularly time consuming because it scanned
buses 0 to 31 brute force. To avoid lengthening boot time, employ a
recursive strategy which only scans buses that are actually reachable
from the root bus.

Yinghai Lu pointed out that the secondary bus number read from a
bridge's config space may be invalid, in particular a value of 0 would
cause an infinite loop. The PCI core goes beyond that and recurses to a
child bus only if its bus number is greater than the parent bus number
(see pci_scan_bridge()). Since the root bus is numbered 0, this implies
that secondary buses may not be 0. Do the same on early scanning.

If this algorithm is found to significantly impact boot time or cause
infinite loops on broken hardware, it would be possible to limit its
recursion depth: The Broadcom 4331 quirk applies at depth 1, all others
at depth 0, so the bus need not be scanned deeper than that for now. An
alternative approach would be to revert to scanning only the root bus,
and apply the Broadcom 4331 quirk to the root ports 8086:1c12, 8086:1e12
and 8086:1e16. Apple always positioned the card behind either of these
three ports. The quirk would then check presence of the card in slot 0
below the root port and do its deed.
Signed-off-by: default avatarLukas Wunner <lukas@wunner.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/f0daa70dac1a9b2483abdb31887173eb6ab77bdf.1465690253.git.lukas@wunner.deSigned-off-by: default avatarIngo Molnar <mingo@kernel.org>
      850c3210
    • Lukas Wunner's avatar
      x86/quirks: Apply nvidia_bugs quirk only on root bus · 447d29d1
      Lukas Wunner authored 
      Since the following commit:

  8659c406 ("x86: only scan the root bus in early PCI quirks")

... early quirks are only applied to devices on the root bus.

The motivation was to prevent application of the nvidia_bugs quirk on
secondary buses.

We're about to reintroduce scanning of secondary buses for a quirk to
reset the Broadcom 4331 wireless card on 2011/2012 Macs. To prevent
regressions, open code the requirement to apply nvidia_bugs only on the
root bus.
Signed-off-by: default avatarLukas Wunner <lukas@wunner.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/4d5477c1d76b2f0387a780f2142bbcdd9fee869b.1465690253.git.lukas@wunner.deSigned-off-by: default avatarIngo Molnar <mingo@kernel.org>
      447d29d1
  3. 09 Jul, 2016 2 commits
    • Dave Hansen's avatar
      x86/cpu: Fix duplicated X86_BUG(9) macro · 8709ed4d
      Dave Hansen authored 
      cpufeatures.h currently defines X86_BUG(9) twice on 32-bit:

	#define X86_BUG_NULL_SEG        X86_BUG(9) /* Nulling a selector preserves the base */
	...
	#ifdef CONFIG_X86_32
	#define X86_BUG_ESPFIX          X86_BUG(9) /* "" IRET to 16-bit SS corrupts ESP/RSP high bits */
	#endif

I think what happened was that this added the X86_BUG_ESPFIX, but
in an #ifdef below most of the bugs:

	58a5aac5 x86/entry/32: Introduce and use X86_BUG_ESPFIX instead of paravirt_enabled

Then this came along and added X86_BUG_NULL_SEG, but collided
with the earlier one that did the bug below the main block
defining all the X86_BUG()s.

	7a5d6704 x86/cpu: Probe the behavior of nulling out a segment at boot time
Signed-off-by: default avatarDave Hansen <dave.hansen@linux.intel.com>
Acked-by: default avatarAndy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160618001503.CEE1B141@viggo.jf.intel.comSigned-off-by: default avatarIngo Molnar <mingo@kernel.org>
      8709ed4d
    • Linus Torvalds's avatar
      Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi · ee40fb29
      Linus Torvalds authored 
      Pull SCSI fixes from James Bottomley:
 "Three fixes.  One is the qla24xx MSI regression, one is a theoretical
  problem over blacklist matching, which would bite USB badly if it ever
  triggered and one is a system hang with a particular type of IPR
  device"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  qla2xxx: Fix NULL pointer deref in QLA interrupt
  SCSI: fix new bug in scsi_dev_info_list string matching
  ipr: Clear interrupt on croc/crocodile when running with LSI
      ee40fb29
  5. 08 Jul, 2016 19 commits
  7. 07 Jul, 2016 11 commits
  9. 06 Jul, 2016 5 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7