[ Upstream commit a01cbae5 ]

Use the element from the loop iteration, not the same element we want to
deactivate otherwise this branch always evaluates true.

Fixes: 6c03ae21 ("netfilter: nft_set_hash: add non-resizable hashtable implementation")
Reported-by: Florian Westphal <fw@strlen.de>
Tested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3b02b0ad ]

Call jhash_1word() for the 4-bytes key case from the insertion and
deactivation path, otherwise big endian arch set lookups fail.

Fixes: 446a8268 ("netfilter: nft_set_hash: add lookup variant for fixed size hashtable")
Reported-by: Florian Westphal <fw@strlen.de>
Tested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 761156ff ]

The length of wmi tlv command for management tx send is calculated
incorrectly in case of protected management frames as there is addition
of IEEE80211_CCMP_MIC_LEN twice. This leads to improper behaviour of
firmware as the wmi tlv mgmt tx send command for protected mgmt frames
is formed wrongly.

Fix the length calculation of wmi tlv command for mgmt tx send in case
of protected management frames by adding the IEEE80211_CCMP_MIC_LEN only
once.

Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1

Fixes: 1807da49 "ath10k: wmi: add management tx by reference support over wmi"
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c25d4788 ]

The wm831x_dcdc_ilim entries needs to be uA because it is used to compare
with min_uA and max_uA.
While at it also make the array const and change to use unsigned int.

Fixes: e4ee831f ("regulator: Add WM831x DC-DC buck convertor support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d410a8a4 ]

To access PRBARn, where n is referenced as a binary number:

MRC p15, 0, <Rt>, c6, c8+n[3:1], 4*n[0] ; Read PRBARn into Rt
MCR p15, 0, <Rt>, c6, c8+n[3:1], 4*n[0] ; Write Rt into PRBARn

To access PRLARn, where n is referenced as a binary number:

MRC p15, 0, <Rt>, c6, c8+n[3:1], 4*n[0]+1 ; Read PRLARn into Rt
MCR p15, 0, <Rt>, c6, c8+n[3:1], 4*n[0]+1 ; Write Rt into PRLARn

For PR{B,L}AR4, n is 4, n[0] is 0, n[3:1] is 2, while current encoding
done with n[0] set to 1 which is wrong. Use proper encoding instead.

Fixes: 046835b4 ("ARM: 8757/1: NOMMU: Support PMSAv8 MPU")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9db043d3 ]

arm64 has got relaxation on GIC version check at early boot stage due
to update of the GIC architecture let's align ARM with that.

To help backports (even though the code was correct at the time of writing)
Fixes: e59941b9 ("ARM: 8527/1: virt: enable GICv3 system registers")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ca70ea43 ]

MCPM does a soft reset of the CPUs and uses common cpu_resume() routine to
perform low-level platform initialization. This results in a try to install
HYP stubs for the second time for each CPU and results in false HYP/SVC
mode mismatch detection. The HYP stubs are already installed at the
beginning of the kernel initialization on the boot CPU (head.S) or in the
secondary_startup() for other CPUs. To fix this issue MCPM code should use
a cpu_resume() routine without HYP stubs installation.

This change fixes HYP/SVC mode mismatch on Samsung Exynos5422-based Odroid
XU3/XU4/HC1 boards.

Fixes: 3721924c ("ARM: 8081/1: MCPM: provide infrastructure to allow for MCPM loopback")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 18b3af44 ]

A change made in the final version of IOMMU debugfs support replaced the
public function iommu_debugfs_new_driver_dir() by the public dentry
iommu_debugfs_dir in <linux/iommu.h>, but forgot to update both the
implementation in iommu-debugfs.c, and the patch description.

Fix this by exporting iommu_debugfs_dir, and removing the reference to
and implementation of iommu_debugfs_new_driver_dir().

Fixes: bad614b2 ("iommu: Enable debugfs exposure of IOMMU driver internals")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1e20186e ]

We need to handle mmc_of_parse() errors during probe otherwise the
MMC driver could start without proper initialization (e.g. power sequence).

Fixes: 476bf3d6 ("mmc: sdhci-brcmstb: Add driver for Broadcom BRCMSTB SoCs")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5085607d ]

If a bulk layout recall or a metadata server reboot coincides with a
umount, then holding a reference to an inode is unsafe unless we
also hold a reference to the super block.

Fixes: fd9a8d71 ("NFSv4.1: Fix bulk recall and destroy of layouts")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c355ec65 ]

In the function wmi_dev_match() the variable id is dereferenced without
first performing a NULL check. The variable can for example be NULL if
a WMI driver is registered without specifying the id_table field in
struct wmi_driver.

Add a NULL check and return that the driver can't handle the device if
the variable is NULL.

Fixes: 844af950 ("platform/x86: wmi: Turn WMI into a bus driver")
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b9307420 ]

While freeing interrupt handlers in error path, don't assume that all
requested interrupts are per-processor interrupts and properly release
standard interrupts too.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 56a94f13 ("clocksource: exynos_mct: Avoid blocking calls in the cpu hotplug notifier")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e7e7e0d7 ]

If the clock tree is not fully populated when the timer-sun5i init code
is called, attempts to get the clock rate for the timer would fail and
return 0.

Make the init code for both clock events and clocksource check the
returned clock rate and fail gracefully if the result is 0, instead of
causing a divide by 0 exception later on.

Fixes: 4a59058f ("clocksource/drivers/sun5i: Refactor the current code")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c60f83b8 ]

Currently, the address range calculation for file-based filters works as
long as the vma that maps the matching part of the object file starts
from offset zero into the file (vm_pgoff==0). Otherwise, the resulting
filter range would be off by vm_pgoff pages. Another related problem is
that in case of a partially matching vma, that is, a vma that matches
part of a filter region, the filter range size wouldn't be adjusted.

Fix the arithmetics around address filter range calculations, taking
into account vma offset, so that the entire calculation is done before
the filter configuration is passed to the PMU drivers instead of having
those drivers do the final bit of arithmetics.

Based on the patch by Adrian Hunter <adrian.hunter.intel.com>.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: 375637bc ("perf/core: Introduce address range filtering")
Link: http://lkml.kernel.org/r/20190215115655.63469-3-alexander.shishkin@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 18736eef ]

When a child event is allocated in the inherit_event() path, the VMA
based filter offsets are not copied from the parent, even though the
address space mapping of the new task remains the same, which leads to
no trace for the new task until exec.
Reported-by: Mansour Alharthi <malharthi9@gatech.edu>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: 375637bc ("perf/core: Introduce address range filtering")
Link: http://lkml.kernel.org/r/20190215115655.63469-2-alexander.shishkin@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6f9449be ]

Fix a soft lockup when NFS client delegation recovery is attempted
but the inode is in the process of being freed. When the
igrab(inode) call fails, and we have to restart the recovery process,
we need to ensure that we won't attempt to recover the same delegation
again.

Fixes: 45870d69 ("NFSv4.1: Test delegation stateids when server...")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8cfaf106 ]

In cpufeatures_process_feature(), if a provided CPU feature is unknown and
enable_unknown is false, we erroneously print that the feature is being
enabled and return true, even though no feature has been enabled, and
may also set feature bits based on the last entry in the match table.

Fix this so that we only set feature bits from the match table if we have
actually enabled a feature from that table, and when failing to enable an
unknown feature, always print the "not enabling" message and return false.

Coincidentally, some older gccs (<GCC 7), when invoked with
-fsanitize-coverage=trace-pc, cause a spurious uninitialised variable
warning in this function:

  arch/powerpc/kernel/dt_cpu_ftrs.c: In function ‘cpufeatures_process_feature’:
  arch/powerpc/kernel/dt_cpu_ftrs.c:686:7: warning: ‘m’ may be used uninitialized in this function [-Wmaybe-uninitialized]
    if (m->cpu_ftr_bit_mask)

An upcoming patch will enable support for kcov, which requires this option.
This patch avoids the warning.

Fixes: 5a61ef74 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Reported-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[ajd: add commit message]
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e8edc32d ]

Clang warns:

drivers/staging/rtlwifi/halmac/halmac_88xx/halmac_func_88xx.c:2472:11:
warning: implicit conversion from enumeration type 'enum
halmac_cmd_process_status' to different enumeration type 'enum
halmac_ret_status' [-Wenum-conversion]
                        return HALMAC_CMD_PROCESS_ERROR;
                        ~~~~~~ ^~~~~~~~~~~~~~~~~~~~~~~~
1 warning generated.

Fix this by using the proper enum for allocation failures,
HALMAC_RET_MALLOC_FAIL, which is used in the rest of this file.

Fixes: e4b08e16 ("staging: r8822be: check kzalloc return or bail")
Link: https://github.com/ClangBuiltLinux/linux/issues/375Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 40cc394b ]

In the rare and unsupported case of a hostname list nfs_parse_devname
will modify dev_name.  There is no need to modify dev_name as the all
that is being computed is the length of the hostname, so the computed
length can just be shorted.

Fixes: dc045898 ("NFS: Use common device name parsing logic for NFSv4 and NFSv2/v3")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9c2054a5 ]

When a DSA port is added to a bridge and brought up, the resulting STP
state programmed into the hardware depends on the order that these
operations are performed.  However, the Linux bridge code believes that
the port is in disabled mode.

If the DSA port is first added to a bridge and then brought up, it will
be in blocking mode.  If it is brought up and then added to the bridge,
it will be in disabled mode.

This difference is caused by DSA always setting the STP mode in
dsa_port_enable() whether or not this port is part of a bridge.  Since
bridge always sets the STP state when the port is added, brought up or
taken down, it is unnecessary for us to manipulate the STP state.

Apparently, this code was copied from Rocker, and the very next day a
similar fix for Rocker was merged but was not propagated to DSA.  See
e47172ab ("rocker: put port in FORWADING state after leaving bridge")

Fixes: b73adef6 ("net: dsa: integrate with SWITCHDEV for HW bridging")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8d166720 ]

The apq8016 driver leaves the of-node refcount at aborting from the
loop of for_each_child_of_node() in the error path.  Not only the
iterator node of for_each_child_of_node(), the children nodes referred
from it for codec and cpu have to be properly unreferenced.

Fixes: bdb052e8 ("ASoC: qcom: add apq8016 sound card support")
Cc: Patrick Lai <plai@codeaurora.org>
Cc: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 36003d4c ]

Commit 4c06c4e6 ("driver core: Fix possible supplier PM-usage
counter imbalance") introduced a regression that causes suppliers
to be suspended prematurely for device links added during consumer
driver probe if the initial PM-runtime status of the consumer is
"suspended" and the consumer is resumed after adding the link and
before pm_runtime_put_suppliers() is called.  In that case,
pm_runtime_put_suppliers() will drop the rpm_active refcount for
the link by one and (since rpm_active is equal to two after the
preceding consumer resume) the supplier's PM-runtime usage counter
will be decremented, which may cause the supplier to suspend even
though the consumer's PM-runtime status is "active".

For this reason, partially revert commit 4c06c4e6 as the problem
it tried to fix needs to be addressed somewhat differently, and
change pm_runtime_get_suppliers() and pm_runtime_put_suppliers() so
that the latter only drops rpm_active references acquired by the
former.  [This requires adding a new field to struct device_link,
but I coulnd't find a cleaner way to address the issue that would
work in all cases.]

This causes pm_runtime_put_suppliers() to effectively ignore device
links added during consumer probe, so device_link_add() doesn't need
to worry about ensuring that suppliers will remain active after
pm_runtime_put_suppliers() for links created with DL_FLAG_RPM_ACTIVE
set and it only needs to bump up rpm_active by one for those links,
so pm_runtime_active_link() is not necessary any more.

Fixes: 4c06c4e6 ("driver core: Fix possible supplier PM-usage counter imbalance")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 785cf1ee ]

The NOUVEAU_GETPARAM_PCI_DEVICE case is missing a break statement and falls
through to the following NOUVEAU_GETPARAM_BUS_TYPE case and may end up
re-assigning the getparam->value to an undesired value. Fix this by adding
in the missing break.

Detected by CoverityScan, CID#1460507 ("Missing break in switch")

Fixes: 359088d5 ("drm/nouveau: remove trivial cases of nvxx_device() usage")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b1d03fc3 ]

Currently the uninitialized values in the array reply are printed out
when exec is false and nvkm_pmu_send has not updated the array. Avoid
confusion by only dumping out these values if they have been actually
updated.

Detected by CoverityScan, CID#1271291 ("Uninitialized scaler variable")
Fixes: ebb58dc2 ("drm/nouveau/pmu: rename from pwr (no binary change)")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 13649101 ]

Currently, the expression for calculating RON is always going to result
in zero no matter the value of ram->mr[1] because the ! operator has
higher precedence than the shift >> operator.  I believe the missing
parentheses around the expression before appying the ! operator will
result in the desired result.

[ Note, not tested ]

Detected by CoveritScan, CID#1324005 ("Operands don't affect result")

Fixes: c25bf7b6 ("drm/nouveau/bios/ramcfg: Separate out RON pull value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 56642837 ]

fpga_qpn was assigned but never used and compilation with W=1
produced the following warning:

drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c: In function _mlx5_fpga_event_:
drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c:320:6: warning:
variable _fpga_qpn_ set but not used [-Wunused-but-set-variable]
  u32 fpga_qpn;
      ^~~~~~~~

Fixes: 98db16ba ("net/mlx5: FPGA, Handle QP error event")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a968b5e9 ]

RGMII_ID specifies that we should have internal delay, so resurrect the
delay addition routine but under the RGMII_ID mode.

Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a5455c91 ]

Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.

Fixes: c90456e3 ("regulator: pv88090: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3c413f59 ]

Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.

Fixes: 99cf3af5 ("regulator: pv88080: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7cd415f8 ]

Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.

Fixes: f307a7e9 ("regulator: pv88060: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit aaf6a5e8 ]

Since we moved the drivers debugfs directory under ieee80211 debugfs the
debugfs entries need to be added after wiphy_register() has been called.
For most part that has been done accordingly, but for the debugfs entries
added by SDIO it was not and failed silently. This patch fixes that by
adding a bus-layer callback for it.

Fixes: 856d5a01 ("brcmfmac: allocate struct brcmf_pub instance using wiphy_new()")
Reported-by: Russel King <linux@armlinux.org.uk>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0742a338 ]

'rv' is the correct return value, pass it upstream instead of 0

Fixes: 17d80d56 ("USB: autosuspend for cdc-wdm")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3e5daee5 ]

Using dma_dev->dev for mappings before it's assigned with the correct
device is unlikely to work as expected, and with future dma-direct
changes, passing a NULL device may end up crashing entirely. I don't
know enough about this hardware or the mv_xor_prep_dma_interrupt()
operation to implement the appropriate error-handling logic that would
have revealed those dma_map_single() calls failing on arm64 for as long
as the driver has been enabled there, but moving the assignment earlier
will at least make the current code operate as intended.

Fixes: 22843545 ("dma: mv_xor: Add support for DMA_INTERRUPT")
Reported-by: John David Anglin <dave.anglin@bell.net>
Tested-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e4b08e16 ]

The kzalloc() in halmac_parse_psd_data_88xx() can fail and return NULL
so check the psd_set->data after allocation and if allocation failed
return HALMAC_CMD_PROCESS_ERROR.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 938a0447 ("staging: r8822be: Add code for halmac sub-drive")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a67614cc ]

The SPAPR TCE KVM device references all hardware IOMMU tables assigned to
some IOMMU group to ensure that in-kernel KVM acceleration of H_PUT_TCE
can work. The tables are references when an IOMMU group gets registered
with the VFIO KVM device by the KVM_DEV_VFIO_GROUP_ADD ioctl;
KVM_DEV_VFIO_GROUP_DEL calls into the dereferencing code
in kvm_spapr_tce_release_iommu_group() which walks through the list of
LIOBNs, finds a matching IOMMU table and calls kref_put() when found.

However that code stops after the very first successful derefencing
leaving other tables referenced till the SPAPR TCE KVM device is destroyed
which normally happens on guest reboot or termination so if we do hotplug
and unplug in a loop, we are leaking IOMMU tables here.

This removes a premature return to let kvm_spapr_tce_release_iommu_group()
find and dereference all attached tables.

Fixes: 121f80ba ("KVM: PPC: VFIO: Add in-kernel acceleration for VFIO")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 780feae7 ]

Fix coccinelle warning:

./drivers/net/phy/mdio_bus.c:51:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44
./drivers/net/phy/mdio_bus.c:52:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44

fix this by using IS_ERR before PTR_ERR

Fixes: bafbdd52 ("phylib: Add device reset GPIO support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ff066653 ]

Fix tps53679_probe() by using dynamically allocated "pmbus_driver_info"
structure instead of static. Usage of static structures causes
overwritten of the field "vrm_version", in case the system is equipped
with several tps53679 devices with the different "vrm_version".
In such case the last probed device overwrites this field for all
others.

Fixes: 61052652 ("hwmon: (pmbus) Add support for Texas Instruments tps53679 device")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0cfd027b ]

pci_map_rom/pci_get_rom_size() performs memory access in the ROM.
In case the Memory Space accesses were disabled, readw() is likely
to trigger a synchronous external abort on some platforms.

In case memory accesses were disabled, re-enable them before the
call and disable them back again just after.

Fixes: 89e1f7d4 ("vfio: Add PCI device driver")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5c88ee02 ]

Since the removal of the stale soc_camera headers, Migo-R board fails to
build due to missing dma-mapping include directive.

Include missing dma-mapping.h header in Migo-R board file to fix the build
error.

Fixes: a50c7738 ("media: sh: migor: Remove stale soc_camera include")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit cb83585e ]

Move q->ndesc initialization before the for loop in mt76u_alloc_rx
since otherwise allocated urbs will not be freed in mt76u_buf_free
Double-check scatterlist pointer in mt76u_buf_free

Fixes: b40b15e1 ("mt76: add usb support to mt76 layer")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>