Audio IPs on Exynos7 require gpios available in AUDIO
pin controller block. So adding the AUDIO pinctrl support.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add MLB+ 3-pin mode pin group to R8A7790 PFC driver.

Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add MLB+ 3-pin mode pin group to R8A7791 PFC driver.

Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The R8A7791 manual sometimes calls the signal MLB_CLK and sometimes MLB_CK; the
latter can only be encountered in the PFC section and  is probably  just a typo
(this  signal is always called MLB_CLK in the R8A7790  manual). Fix occurences
of MLB_CK throughout the R8A7791 PFC driver.

Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

marco chip has been dropped, clear its support.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make also
of_device_id array const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make also
of_device_id array const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The A31s is a stripped down version of the A31, as such it is missing some
pins and some functions on some pins.

The new pinctrl-sun6i-a31s.c this commit adds is a copy of pinctrl-sun6i-a31s.c
with the missing pins and functions removed.

Note there is no a31s specific version of pinctrl-sun6i-a31-r.c, as the
prcm pins are identical between the A31 and the A31s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

While working on pinctrl for the A31s, I noticed that function 4 of
PA15 - PA18 was missing, add these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These functions are supposed to return an error pointer, not NULL.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

USB and Power regulator on Exynos7 require gpios available
in BUS1 pin controller block.
So adding the BUS1 pinctrl support.
Signed-off-by: Naveen Krishna Ch <naveenkrishna.ch@gmail.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Adding list of aliases for supported Exynos7 pin controller blocks.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

New pin controllers such as ACPI-based may also have custom properties
to parse, and should be able to use generic pin config. Let's make the
code compile on !OF systems and rename members a bit to underscore it
is custom parameters and not necessarily DT parameters.

This fixes a build regression for x86_64 on the zeroday kernel builds.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-and-tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of the driver caring about implementation details like device
tree, just provide information about driver specific pinconf parameters
to pinconf-generic which takes care of parsing the DT.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds a pin-control driver for Zynq.

Changes since v2:
- driver-specific DT properties are passed to the core in two arrays,
  one for the actual DT parsing one for the debugfs representation.
  Issue a compiler warning when the number of entries is not the same
  for both arrays.

Changes since v1:
 - fix EMIO_SD1_CD pin name
 - add USB to pinmux options

changes since RFCv2:
 - let Zynq select PINCTRL_ZYNQ. Boot hangs when pinctrl information is
   present in DT but no driver available.
 - add #defines to get rid of magical constants
 - add commas at end of initializers
 - separate changes in mach-zynq in separate patch
 - add driver specific io-standard DT property
 - refactored pinconf set function to not require arguments for
   argument-less properties
 - squash other patches in
   - support for IO-standard property
   - support for low-power mode property
   - migration to pinconf_generic_dt_node_to_map_all()
 - use newly created infrastructure to add pass driver-specific DT
   params to pinconf-generic

changes since RFC:
 - use syscon/regmap to access registers in SLCR space
 - rebase to 3.18: rename enable -> set_mux
 - add kernel-doc
 - support pinconf
   - supported attributes
     - pin-bias: pull up, tristate, disable
     - slew-rate: 0 == slow, 1 == fast; generic pinconf does not display
       argument
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add documentation for the devicetree binding for the Zynq pincontroller.

Changes since v1:
 - fix typo
 - add USB related documentation
 - remove 'pinctrl-' prefix for pinctrl sub-nodes
 - update documentation to enforce strict separation of pinmux
   and pinconf nodes
   - update example accordingly
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Additionally to the generic DT parameters, allow drivers to provide
driver-specific DT parameters to be used with the generic parser
infrastructure.

To achieve this 'struct pinctrl_desc' is extended to pass custom pinconf
option to the core. In order to pass this kind of information, the
related data structures - 'struct pinconf_generic_dt_params',
'pin_config_item' - are moved from pinconf internals to the
pinconf-generic header.

Additionally pinconfg-generic is refactored to not only iterate over the
generic pinconf parameters but also take the parameters into account
that are provided through the driver's 'struct pinctrl_desc'.
In particular 'pinconf_generic_parse_dt_config()' and
'pinconf_generic_dump' helpers are split into two parts each. In order
to have a more generic helper that can be used to process the generic
parameters as well as the driver-specific ones.

v2:
 - fix typo
 - add missing documentation for @conf_items member in struct
 - rebase to pinctrl/devel: conflict in abx500
 - rename _pinconf_generic_dump() to pinconf_generic_dump_one()
 - removed '_' from _parse_dt_cfg()
 - removed BUG_ONs, error condition is handled in if statements
 - removed pinconf_generic_dump_group() & pinconf_generic_dump_pin
   helpers
   - fixed up corresponding call sites
   - renamed pinconf_generic_dump() to pinconf_generic_dump_pins()
   - added kernel-doc to pinconf_generic_dump_pins()
 - add kernel-doc
 - more verbose commit message
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

With the new 'groups' property, the DT parser can infer the map type
from the fact whether 'pins' or 'groups' is used to specify the pin
group to work on.

To maintain backwards compatibitliy with current usage of the DT
binding, this is only done when PIN_MAP_TYPE_INVALID is passed to the
parsing function as type.

Also, a new helper 'pinconf_generic_dt_node_to_map_all()' is introduced,
which can be used by drivers as generic callback for dt_node_to_map() to
leverage the new feature.

Changes since v2:
 - rename dt_pin_specifier to subnode_target_type
 - add additional comment in header file explaining passing an invalid
   map type
 - mention map_all() helper in commit message
Changes since RFC v2:
 - none
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When drivers are compiled in subdirectories the -DDEBUG flag need
to be passed in the individual Makefiles.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Suggested-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

After the Nomadik pin controller was force migrated to generic pin
control bindings, some leftovers in the documentation need to be
cleaned up. The code and device trees are already migrated.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The MPP19 and MMP20 pins also have the ability to be muxed to the uart1
function.

Add this case to the pinctrl driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Before resuming from system sleep BIOS restores its view of pin
configuration. If we have configured some pins differently from that, for
instance some driver requested a pin as a GPIO but it was not in GPIO mode
originally, our view of the pin configuration will not match the hardware
state anymore.

This patch saves the pin configuration and interrupt mask registers on
suspend and restores them on exit. This should make sure that the
previously configured state is still in effect.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull KVM fixes from Paolo Bonzini:
 "The important fixes are for two bugs introduced by the merge window.

  On top of this, add a couple of WARN_ONs and stop spamming dmesg on
  pretty much every boot of a virtual machine"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: warn on more invariant breakage
  kvm: fix sorting of memslots with base_gfn == 0
  kvm: x86: drop severity of "generation wraparound" message
  kvm: x86: vmx: reorder some msr writing

Pull vfs fix from Al Viro:
 "An embarrassing bug in lustre patches from this cycle ;-/"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  [regression] braino in "lustre: use is_root_inode()"

Modifying a non-existent slot is not allowed.  Also check that the
first loop doesn't move a deleted slot beyond the used part of
the mslots array.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Before commit 0e60b079 (kvm: change memslot sorting rule from size
to GFN, 2014-12-01), the memslots' sorting key was npages, meaning
that a valid memslot couldn't have its sorting key equal to zero.
On the other hand, a valid memslot can have base_gfn == 0, and invalid
memslots are identified by base_gfn == npages == 0.

Because of this, commit 0e60b079 broke the invariant that invalid
memslots are at the end of the mslots array.  When a memslot with
base_gfn == 0 was created, any invalid memslot before it were left
in place.

This can be fixed by changing the insertion to use a ">=" comparison
instead of "<=", but some care is needed to avoid breaking the case
of deleting a memslot; see the comment in update_memslots.

Thanks to Tiejun Chen for posting an initial patch for this bug.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Pull sound fixes from Takashi Iwai:
 "Just a couple of fixes for the new Intel Skylake HD-audio support"

* tag 'sound-3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda_intel: apply the Seperate stream_tag for Skylake
  ALSA: hda_controller: Separate stream_tag for input and output streams.

Since most virtual machines raise this message once, it is a bit annoying.
Make it KERN_DEBUG severity.

Cc: stable@vger.kernel.org
Fixes: 7a2e8aafSigned-off-by: Paolo Bonzini <pbonzini@redhat.com>

The commit 34a1cd60, "x86: vmx: move some vmx setting from
vmx_init() to hardware_setup()", tried to refactor some codes
specific to vmx hardware setting into hardware_setup(), but some
msr writing should depend on our previous setting condition like
enable_apicv, enable_ept and so on.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

In one of the places (ll_md_blocking_ast()) we had open-coded
!is_root_inode(inode) and replaced it with is_root_inode(inode).
See the last chunk of f76c23:
-                   inode != inode->i_sb->s_root->d_inode)
+                   is_root_inode(inode))
should've been
+                   !is_root_inode(inode))
obviously...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull parisc build fix from Helge Deller:
 "This unbreaks the kernel compilation on parisc with gcc-4.9"

* 'parisc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: fix out-of-register compiler error in ldcw inline assembler function

The __ldcw macro has a problem when its argument needs to be reloaded from
memory. The output memory operand and the input register operand both need to
be reloaded using a register in class R1_REGS when generating 64-bit code.
This fails because there's only a single register in the class. Instead, use a
memory clobber. This also makes the __ldcw macro a compiler memory barrier.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org>        [3.13+]
Signed-off-by: Helge Deller <deller@gmx.de>

The total stream number of Skylake's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.

This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Implemented separate stream_tag assignment for input and output streams.
According to hda specification stream tag must be unique throughout the
input streams group, however an output stream might use a stream tag
which is already in use by an input stream. This change is necessary
to support HW which provides a total of more than 15 stream DMA engines
which with legacy implementation causes an overflow on SDxCTL.STRM
field (and the whole SDxCTL register) and as a result usage of
Reserved value 0 in the SDxCTL.STRM field which confuses HDA controller.
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull drm fixes from Dave Airlie:
 "Xmas fixes pull:

  core:
      one atomic fix, revert the WARN_ON dumb buffers patch.

  agp:
      fixup Dave J.

  nouveau:
      fix 3.18 regression for old userspace

  tegra fixes:
      vblank and iommu fixes

  amdkfd:
      fix bugs shown by testing with userspace, init apertures once

  msm:
      hdmi fixes and cleanup

  i915:
      misc fixes

  There is also a link ordering fix that I've asked to be cc'ed to you,
  putting iommu before gpu, it fixes an issue with amdkfd when things
  are all in the kernel, but I didn't like sending it via my tree
  without discussion.

  I'll probably be a bit on/off for a few weeks with pulls now, due to
  holidays and LCA, so don't be surprised if stuff gets a bit backed up,
  and things end up a bit large due to lag"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
  Revert "drm/gem: Warn on illegal use of the dumb buffer interface v2"
  agp: Fix up email address & attributions in AGP MODULE_AUTHOR tags
  nouveau: bring back legacy mmap handler
  drm/msm/hdmi: rework HDMI IRQ handler
  drm/msm/hdmi: enable regulators before clocks to avoid warnings
  drm/msm/mdp5: update irqs on crtc<->encoder link change
  drm/msm: block incoming update on pending updates
  drm/atomic: fix potential null ptr on plane enable
  drm/msm: Deletion of unnecessary checks before the function call "release_firmware"
  drm/msm: Deletion of unnecessary checks before two function calls
  drm/tegra: dc: Select root window for event dispatch
  drm/tegra: gem: Use the proper size for GEM objects
  drm/tegra: gem: Flush buffer objects upon allocation
  drm/tegra: dc: Fix a potential race on page-flip completion
  drm/tegra: dc: Consistently use the same pipe
  drm/irq: Add drm_crtc_vblank_count()
  drm/irq: Add drm_crtc_handle_vblank()
  drm/irq: Add drm_crtc_send_vblank_event()
  drm/i915: Disable PSMI sleep messages on all rings around context switches
  drm/i915: Force the CS stall for invalidate flushes
  ...

Pull ipmi driver bugfixes from Corey Minyard:
 "Fix two bugs:

  One that lockdep turned up, I didn't go far enough with cleanup of
  attributes for IPMI.  This has been there a long time; my previous fix
  of this didn't fix all the attributes.

  One fix for some arches that need an explicit linux/ctype.h for
  isspace()"

* tag 'for-linus-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
  ipmi: Fix compile issue with isspace()
  ipmi: Finish cleanup of BMC attributes

This reverts commit 355a7018.

This had some bad side effects under normal operation, and should
have been dropped earlier.
Signed-off-by: Dave Airlie <airlied@redhat.com>

- Display MEC fw version in topology. Without this, the HSA userspace
  stack is broken.

- Init apertures information only once per process

* tag 'amdkfd-fixes-2014-12-23' of git://people.freedesktop.org/~gabbayo/linux:
  amdkfd: init aperture once per process
  amdkfd: Display MEC fw version in topology node
  drm/radeon: Add implementation of get_fw_version
  drm/amd: Add get_fw_version to kfd-->kgd interface