- 25 Apr, 2024 2 commits
-
-
Linus Walleij authored
Merge tag 'intel-pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes intel-pinctrl for v6.9-1 * Correct GPIO selection and add UART3 pins for Intel Bay Trail The following is an automated git shortlog grouped by driver: baytrail: - Add pinconf group for uart3 - Fix selecting gpio pinctrl state Signed-off-by:
Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
Merge tag 'renesas-pinctrl-fixes-for-v6.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into fixes pinctrl: renesas: Fixes for v6.9 (take two) - Fix interrupt configuration on RZ/G2L after s2ram. Signed-off-by:
-
- 22 Apr, 2024 1 commit
-
-
Claudiu Beznea authored
Commit dce0919c ("irqchip/renesas-rzg2l: Do not set TIEN and TINT source at the same time") removed the setup of TINT from rzg2l_irqc_irq_enable(). To address the spurious interrupt issue the setup of TINT has been moved in rzg2l_tint_set_edge() through rzg2l_disable_tint_and_set_tint_source(). With this, the interrupts are not properly re-configured after a suspend-to-RAM cycle. To address this issue and avoid spurious interrupts while resumming set the interrupt type before enabling it. Fixes: dce0919c ("irqchip/renesas-rzg2l: Do not set TIEN and TINT source at the same time") Signed-off-by:
Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20240419063822.3467424-1-claudiu.beznea.uj@bp.renesas.comSigned-off-by:
-
- 17 Apr, 2024 1 commit
-
-
Linus Walleij authored
Merge tag 'renesas-pinctrl-fixes-for-v6.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into fixes pinctrl: renesas: Fixes for v6.9 - Fix a dtbs_check warning on RZ/G3S, - Fix a lockdep warning on RZ/G2L. Signed-off-by:
-
- 16 Apr, 2024 1 commit
-
-
Zeng Heng authored
If we fail to allocate propname buffer, we need to drop the reference count we just took. Because the pinctrl_dt_free_maps() includes the droping operation, here we call it directly. Fixes: 91d5c506 ("pinctrl: devicetree: fix null pointer dereferencing in pinctrl_dt_to_map") Suggested-by:
Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by:
Zeng Heng <zengheng4@huawei.com> Reviewed-by:
-
- 08 Apr, 2024 2 commits
-
-
Hans de Goede authored
GPIO_S0_SC57 / GPIO_S0_SC61 can be muxed to PCU_UART_TXD / PCU_UART_RXD, add a pinconf group for this. On Bay Trail board schematics using these pins as UART these are called UART3_TXD / UART3_RXD, name the pinconf group "uart3_grp" to be consistent with the schematics. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com>
-
Hans de Goede authored
For all the "score" pin-groups all the intel_pingroup-s to select the non GPIO function are re-used for byt_score_gpio_groups[]. But this is incorrect since a pin-group includes the mode setting, which for the non GPIO functions generally is 1, where as to select the GPIO function mode must be set to 0. So the GPIO function needs separate intel_pingroup-s with their own mode value of 0. Add a new PIN_GROUP_GPIO macro which adds a foo_gpio entry to each pin-group defined this way and update byt_score_gpio_groups[] to point to the new foo_gpio entries. The "sus" usb_oc_grp usb_ulpi_grp and pcu_spi_grp pin-groups are special because these have a non 0 mode value to select the GPIO functions and these already have matching foo_gpio pin-groups, leave these are unchanged. The pmu_clk "sus" groups added in commit 2f46d7f7 ("pinctrl: baytrail: Add pinconf group + function for the pmu_clk") do need to use the new PIN_GROUP_GPIO macro. Fixes: 2f46d7f7 ("pinctrl: baytrail: Add pinconf group + function for the pmu_clk") Signed-off-by:
-
- 04 Apr, 2024 2 commits
-
-
Chen-Yu Tsai authored
There is a misinterpretation of some of the PIN_CONFIG_* options in this driver library. PIN_CONFIG_OUTPUT_ENABLE should refer to a buffer or switch in the output direction of the electrical path. The MediaTek hardware does not have such a thing. The driver incorrectly maps this option to the GPIO function's direction. Likewise, PIN_CONFIG_INPUT_ENABLE should refer to a buffer or switch in the input direction. The hardware does have such a mechanism, and is mapped to the IES bit. The driver however sets the direction in addition to the IES bit, which is incorrect. On readback, the IES bit isn't even considered. Ironically, the driver does not support readback for PIN_CONFIG_OUTPUT, while its readback of PIN_CONFIG_{INPUT,OUTPUT}_ENABLE is what it should be doing for PIN_CONFIG_OUTPUT. Rework support for these three options, so that PIN_CONFIG_OUTPUT_ENABLE is completely removed, PIN_CONFIG_INPUT_ENABLE is only linked to the IES bit, and PIN_CONFIG_OUTPUT is linked to the GPIO function's direction and output level. Fixes: 80525098 ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings") Signed-off-by:Chen-Yu Tsai <wenst@chromium.org> Reviewed-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Message-ID: <20240327091336.3434141-3-wenst@chromium.org> Signed-off-by:
-
Chen-Yu Tsai authored
In the generic pin config library, readback of some options are handled differently compared to the setting of those options: the argument value is used to convey enable/disable of an option in the set path, but success or -EINVAL is used to convey if an option is enabled or disabled in the debugfs readback path. PIN_CONFIG_INPUT_SCHMITT_ENABLE is one such option. Fix the readback of the option in the mediatek-paris library, so that the debugfs dump is not showing "input schmitt enabled" for pins that don't have it enabled. Fixes: 1bea6afb ("pinctrl: mediatek: Refine mtk_pinconf_get()") Signed-off-by:
-
- 28 Mar, 2024 3 commits
-
-
Dan Carpenter authored
The "pctldev" struct is allocated in devm_pinctrl_register_and_init(). It's a devm_ managed pointer that is freed by devm_pinctrl_dev_release(), so freeing it in pinctrl_enable() will lead to a double free. The devm_pinctrl_dev_release() function frees the pindescs and destroys the mutex as well. Fixes: 61187142 ("pinctrl: core: Fix pinctrl_register_and_init() with pinctrl_enable()") Signed-off-by:
-
Jan Dakinevich authored
Other pins have _a or _x suffix, but this one doesn't have any. Most likely this is a typo. Fixes: dabad1ff ("pinctrl: meson: add pinctrl driver support for Meson-A1 SoC") Signed-off-by:
Jan Dakinevich <jan.dakinevich@salutedevices.com> Reviewed-by:
Neil Armstrong <neil.armstrong@linaro.org> Message-ID: <20240325113058.248022-1-jan.dakinevich@salutedevices.com> Signed-off-by:
-
Billy Tsai authored
The register offset to disable the internal pull-down of GPIOR~T is 0x630 instead of 0x620, as specified in the Ast2600 datasheet v15 The datasheet can download from the official Aspeed website. Fixes: 15711ba6 ("pinctrl: aspeed-g6: Add AST2600 pinconf support") Reported-by:
Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> Signed-off-by:
Billy Tsai <billy_tsai@aspeedtech.com> Reviewed-by:
Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by:
Andrew Jeffery <andrew@codeconstruct.com.au> Message-ID: <20240313092809.2596644-1-billy_tsai@aspeedtech.com> Signed-off-by:
-
- 26 Mar, 2024 2 commits
-
-
Claudiu Beznea authored
Lockdep detects a possible deadlock as listed below. This is because it detects the IA55 interrupt controller .irq_eoi() API is called from interrupt context while configuration-specific API (e.g., .irq_enable()) could be called from process context on resume path (by calling rzg2l_gpio_irq_restore()). To avoid this, protect the call of rzg2l_gpio_irq_enable() with spin_lock_irqsave()/spin_unlock_irqrestore(). With this the same approach that is available in __setup_irq() is mimicked to pinctrl IRQ resume function. Below is the lockdep report: WARNING: inconsistent lock state 6.8.0-rc5-next-20240219-arm64-renesas-00030-gb17a289abf1f #90 Not tainted -------------------------------- inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage. str_rwdt_t_001./159 [HC0[0]:SC0[0]:HE1:SE1] takes: ffff00000b001d70 (&rzg2l_irqc_data->lock){?...}-{2:2}, at: rzg2l_irqc_irq_enable+0x60/0xa4 {IN-HARDIRQ-W} state was registered at: lock_acquire+0x1e0/0x310 _raw_spin_lock+0x44/0x58 rzg2l_irqc_eoi+0x2c/0x130 irq_chip_eoi_parent+0x18/0x20 rzg2l_gpio_irqc_eoi+0xc/0x14 handle_fasteoi_irq+0x134/0x230 generic_handle_domain_irq+0x28/0x3c gic_handle_irq+0x4c/0xbc call_on_irq_stack+0x24/0x34 do_interrupt_handler+0x78/0x7c el1_interrupt+0x30/0x5c el1h_64_irq_handler+0x14/0x1c el1h_64_irq+0x64/0x68 _raw_spin_unlock_irqrestore+0x34/0x70 __setup_irq+0x4d4/0x6b8 request_threaded_irq+0xe8/0x1a0 request_any_context_irq+0x60/0xb8 devm_request_any_context_irq+0x74/0x104 gpio_keys_probe+0x374/0xb08 platform_probe+0x64/0xcc really_probe+0x140/0x2ac __driver_probe_device+0x74/0x124 driver_probe_device+0x3c/0x15c __driver_attach+0xec/0x1c4 bus_for_each_dev+0x70/0xcc driver_attach+0x20/0x28 bus_add_driver+0xdc/0x1d0 driver_register+0x5c/0x118 __platform_driver_register+0x24/0x2c gpio_keys_init+0x18/0x20 do_one_initcall+0x70/0x290 kernel_init_freeable+0x294/0x504 kernel_init+0x20/0x1cc ret_from_fork+0x10/0x20 irq event stamp: 69071 hardirqs last enabled at (69071): [<ffff800080e0dafc>] _raw_spin_unlock_irqrestore+0x6c/0x70 hardirqs last disabled at (69070): [<ffff800080e0cfec>] _raw_spin_lock_irqsave+0x7c/0x80 softirqs last enabled at (67654): [<ffff800080010614>] __do_softirq+0x494/0x4dc softirqs last disabled at (67645): [<ffff800080015238>] ____do_softirq+0xc/0x14 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&rzg2l_irqc_data->lock); <Interrupt> lock(&rzg2l_irqc_data->lock); *** DEADLOCK *** 4 locks held by str_rwdt_t_001./159: #0: ffff00000b10f3f0 (sb_writers#4){.+.+}-{0:0}, at: vfs_write+0x1a4/0x35c #1: ffff00000e43ba88 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0xe8/0x1a8 #2: ffff00000aa21dc8 (kn->active#40){.+.+}-{0:0}, at: kernfs_fop_write_iter+0xf0/0x1a8 #3: ffff80008179d970 (system_transition_mutex){+.+.}-{3:3}, at: pm_suspend+0x9c/0x278 stack backtrace: CPU: 0 PID: 159 Comm: str_rwdt_t_001. Not tainted 6.8.0-rc5-next-20240219-arm64-renesas-00030-gb17a289abf1f #90 Hardware name: Renesas SMARC EVK version 2 based on r9a08g045s33 (DT) Call trace: dump_backtrace+0x94/0xe8 show_stack+0x14/0x1c dump_stack_lvl+0x88/0xc4 dump_stack+0x14/0x1c print_usage_bug.part.0+0x294/0x348 mark_lock+0x6b0/0x948 __lock_acquire+0x750/0x20b0 lock_acquire+0x1e0/0x310 _raw_spin_lock+0x44/0x58 rzg2l_irqc_irq_enable+0x60/0xa4 irq_chip_enable_parent+0x1c/0x34 rzg2l_gpio_irq_enable+0xc4/0xd8 rzg2l_pinctrl_resume_noirq+0x4cc/0x520 pm_generic_resume_noirq+0x28/0x3c genpd_finish_resume+0xc0/0xdc genpd_resume_noirq+0x14/0x1c dpm_run_callback+0x34/0x90 device_resume_noirq+0xa8/0x268 dpm_noirq_resume_devices+0x13c/0x160 dpm_resume_noirq+0xc/0x1c suspend_devices_and_enter+0x2c8/0x570 pm_suspend+0x1ac/0x278 state_store+0x88/0x124 kobj_attr_store+0x14/0x24 sysfs_kf_write+0x48/0x6c kernfs_fop_write_iter+0x118/0x1a8 vfs_write+0x270/0x35c ksys_write+0x64/0xec __arm64_sys_write+0x18/0x20 invoke_syscall+0x44/0x108 el0_svc_common.constprop.0+0xb4/0xd4 do_el0_svc+0x18/0x20 el0_svc+0x3c/0xb8 el0t_64_sync_handler+0xb8/0xbc el0t_64_sync+0x14c/0x150 Fixes: 254203f9 ("pinctrl: renesas: rzg2l: Add suspend/resume support") Signed-off-by: -
Lad Prabhakar authored
On the RZ/G3S SMARC platform, the 'input' property is utilized in gpio-hog nodes, and the 'output-enable' property is used for ETH0/1 TXC pins. Update the binding documentation to include these properties, addressing the following dtbs_check warnings: arch/arm64/boot/dts/renesas/r9a08g045s33-smarc.dtb: pinctrl@11030000: key-1-gpio-hog: 'anyOf' conditional failed, one must be fixed: 'input' does not match any of the regexes: 'pinctrl-[0-9]+' arch/arm64/boot/dts/renesas/r9a08g045s33-smarc.dtb: pinctrl@11030000: eth0: 'anyOf' conditional failed, one must be fixed: 'output-enable' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
-
- 24 Mar, 2024 13 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efiLinus Torvalds authored
Pull EFI fixes from Ard Biesheuvel: - Fix logic that is supposed to prevent placement of the kernel image below LOAD_PHYSICAL_ADDR - Use the firmware stack in the EFI stub when running in mixed mode - Clear BSS only once when using mixed mode - Check efi.get_variable() function pointer for NULL before trying to call it * tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi: efi: fix panic in kdump kernel x86/efistub: Don't clear BSS twice in mixed mode x86/efistub: Call mixed mode boot services on the firmware's stack efi/libstub: fix efi_random_alloc() to allocate memory at alloc_min or higher address
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: - Ensure that the encryption mask at boot is properly propagated on 5-level page tables, otherwise the PGD entry is incorrectly set to non-encrypted, which causes system crashes during boot. - Undo the deferred 5-level page table setup as it cannot work with memory encryption enabled. - Prevent inconsistent XFD state on CPU hotplug, where the MSR is reset to the default value but the cached variable is not, so subsequent comparisons might yield the wrong result and as a consequence the result prevents updating the MSR. - Register the local APIC address only once in the MPPARSE enumeration to prevent triggering the related WARN_ONs() in the APIC and topology code. - Handle the case where no APIC is found gracefully by registering a fake APIC in the topology code. That makes all related topology functions work correctly and does not affect the actual APIC driver code at all. - Don't evaluate logical IDs during early boot as the local APIC IDs are not yet enumerated and the invoked function returns an error code. Nothing requires the logical IDs before the final CPUID enumeration takes place, which happens after the enumeration. - Cure the fallout of the per CPU rework on UP which misplaced the copying of boot_cpu_data to per CPU data so that the final update to boot_cpu_data got lost which caused inconsistent state and boot crashes. - Use copy_from_kernel_nofault() in the kprobes setup as there is no guarantee that the address can be safely accessed. - Reorder struct members in struct saved_context to work around another kmemleak false positive - Remove the buggy code which tries to update the E820 kexec table for setup_data as that is never passed to the kexec kernel. - Update the resource control documentation to use the proper units. - Fix a Kconfig warning observed with tinyconfig * tag 'x86-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/boot/64: Move 5-level paging global variable assignments back x86/boot/64: Apply encryption mask to 5-level pagetable update x86/cpu: Add model number for another Intel Arrow Lake mobile processor x86/fpu: Keep xfd_state in sync with MSR_IA32_XFD Documentation/x86: Document that resctrl bandwidth control units are MiB x86/mpparse: Register APIC address only once x86/topology: Handle the !APIC case gracefully x86/topology: Don't evaluate logical IDs during early boot x86/cpu: Ensure that CPU info updates are propagated on UP kprobes/x86: Use copy_from_kernel_nofault() to read from unsafe address x86/pm: Work around false positive kmemleak report in msr_build_context() x86/kexec: Do not update E820 kexec table for setup_data x86/config: Fix warning for 'make ARCH=x86_64 tinyconfig'
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler doc clarification from Thomas Gleixner: "A single update for the documentation of the base_slice_ns tunable to clarify that any value which is less than the tick slice has no effect because the scheduler tick is not guaranteed to happen within the set time slice" * tag 'sched-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/doc: Update documentation for base_slice_ns and CONFIG_HZ relation
-
git://git.infradead.org/users/hch/dma-mappingLinus Torvalds authored
Pull dma-mapping fixes from Christoph Hellwig: "This has a set of swiotlb alignment fixes for sometimes very long standing bugs from Will. We've been discussion them for a while and they should be solid now" * tag 'dma-mapping-6.9-2024-03-24' of git://git.infradead.org/users/hch/dma-mapping: swiotlb: Reinstate page-alignment for mappings >= PAGE_SIZE iommu/dma: Force swiotlb_max_mapping_size on an untrusted device swiotlb: Fix alignment checks when both allocation and DMA masks are present swiotlb: Honour dma_alloc_coherent() alignment in swiotlb_alloc() swiotlb: Enforce page alignment in swiotlb_alloc() swiotlb: Fix double-allocation of slots due to broken alignment handling
-
Oleksandr Tymoshenko authored
Check if get_next_variable() is actually valid pointer before calling it. In kdump kernel this method is set to NULL that causes panic during the kexec-ed kernel boot. Tested with QEMU and OVMF firmware. Fixes: bad267f9 ("efi: verify that variable services are supported") Signed-off-by:
Oleksandr Tymoshenko <ovt@google.com> Signed-off-by:
Ard Biesheuvel <ardb@kernel.org>
-
Ard Biesheuvel authored
Clearing BSS should only be done once, at the very beginning. efi_pe_entry() is the entrypoint from the firmware, which may not clear BSS and so it is done explicitly. However, efi_pe_entry() is also used as an entrypoint by the mixed mode startup code, in which case BSS will already have been cleared, and doing it again at this point will corrupt global variables holding the firmware's GDT/IDT and segment selectors. So make the memset() conditional on whether the EFI stub is running in native mode. Fixes: b3810c5a ("x86/efistub: Clear decompressor BSS in native EFI entrypoint") Signed-off-by:
-
Ard Biesheuvel authored
Normally, the EFI stub calls into the EFI boot services using the stack that was live when the stub was entered. According to the UEFI spec, this stack needs to be at least 128k in size - this might seem large but all asynchronous processing and event handling in EFI runs from the same stack and so quite a lot of space may be used in practice. In mixed mode, the situation is a bit different: the bootloader calls the 32-bit EFI stub entry point, which calls the decompressor's 32-bit entry point, where the boot stack is set up, using a fixed allocation of 16k. This stack is still in use when the EFI stub is started in 64-bit mode, and so all calls back into the EFI firmware will be using the decompressor's limited boot stack. Due to the placement of the boot stack right after the boot heap, any stack overruns have gone unnoticed. However, commit 5c4feadb0011983b ("x86/decompressor: Move global symbol references to C code") moved the definition of the boot heap into C code, and now the boot stack is placed right at the base of BSS, where any overruns will corrupt the end of the .data section. While it would be possible to work around this by increasing the size of the boot stack, doing so would affect all x86 systems, and mixed mode systems are a tiny (and shrinking) fraction of the x86 installed base. So instead, record the firmware stack pointer value when entering from the 32-bit firmware, and switch to this stack every time a EFI boot service call is made. Cc: <stable@kernel.org> # v6.1+ Signed-off-by: -
Tom Lendacky authored
Commit 63bed966 ("x86/startup_64: Defer assignment of 5-level paging global variables") moved assignment of 5-level global variables to later in the boot in order to avoid having to use RIP relative addressing in order to set them. However, when running with 5-level paging and SME active (mem_encrypt=on), the variables are needed as part of the page table setup needed to encrypt the kernel (using pgd_none(), p4d_offset(), etc.). Since the variables haven't been set, the page table manipulation is done as if 4-level paging is active, causing the system to crash on boot. While only a subset of the assignments that were moved need to be set early, move all of the assignments back into check_la57_support() so that these assignments aren't spread between two locations. Instead of just reverting the fix, this uses the new RIP_REL_REF() macro when assigning the variables. Fixes: 63bed966 ("x86/startup_64: Defer assignment of 5-level paging global variables") Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
Ingo Molnar <mingo@kernel.org> Reviewed-by:
-
Tom Lendacky authored
When running with 5-level page tables, the kernel mapping PGD entry is updated to point to the P4D table. The assignment uses _PAGE_TABLE_NOENC, which, when SME is active (mem_encrypt=on), results in a page table entry without the encryption mask set, causing the system to crash on boot. Change the assignment to use _PAGE_TABLE instead of _PAGE_TABLE_NOENC so that the encryption mask is set for the PGD entry. Fixes: 533568e0 ("x86/boot/64: Use RIP_REL_REF() to access early_top_pgt[]") Signed-off-by:
-
Tony Luck authored
This one is the regular laptop CPU. Signed-off-by:
Tony Luck <tony.luck@intel.com> Signed-off-by:
-
Adamos Ttofari authored
Commit 67236547 ("x86/fpu: Update XFD state where required") and commit 8bf26758 ("x86/fpu: Add XFD state to fpstate") introduced a per CPU variable xfd_state to keep the MSR_IA32_XFD value cached, in order to avoid unnecessary writes to the MSR. On CPU hotplug MSR_IA32_XFD is reset to the init_fpstate.xfd, which wipes out any stale state. But the per CPU cached xfd value is not reset, which brings them out of sync. As a consequence a subsequent xfd_update_state() might fail to update the MSR which in turn can result in XRSTOR raising a #NM in kernel space, which crashes the kernel. To fix this, introduce xfd_set_state() to write xfd_state together with MSR_IA32_XFD, and use it in all places that set MSR_IA32_XFD. Fixes: 67236547 ("x86/fpu: Update XFD state where required") Signed-off-by:
Adamos Ttofari <attofari@amazon.de> Signed-off-by:
Chang S. Bae <chang.seok.bae@intel.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240322230439.456571-1-chang.seok.bae@intel.com Closes: https://lore.kernel.org/lkml/20230511152818.13839-1-attofari@amazon.de
-
Tony Luck authored
The memory bandwidth software controller uses 2^20 units rather than 10^6. See mbm_bw_count() which computes bandwidth using the "SZ_1M" Linux define for 0x00100000. Update the documentation to use MiB when describing this feature. It's too late to fix the mount option "mba_MBps" as that is now an established user interface. Signed-off-by:
-
- 23 Mar, 2024 11 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Thomas Gleixner: "Two regression fixes for the timer and timer migration code: - Prevent endless timer requeuing which is caused by two CPUs racing out of idle. This happens when the last CPU goes idle and therefore has to ensure to expire the pending global timers and some other CPU come out of idle at the same time and the other CPU wins the race and expires the global queue. This causes the last CPU to chase ghost timers forever and reprogramming it's clockevent device endlessly. Cure this by re-evaluating the wakeup time unconditionally. - The split into local (pinned) and global timers in the timer wheel caused a regression for NOHZ full as it broke the idle tracking of global timers. On NOHZ full this prevents an self IPI being sent which in turn causes the timer to be not programmed and not being expired on time. Restore the idle tracking for the global timer base so that the self IPI condition for NOHZ full is working correctly again" * tag 'timers-urgent-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: timers: Fix removed self-IPI on global timer's enqueue in nohz_full timers/migration: Fix endless timer requeue after idle interrupts -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull more clocksource updates from Thomas Gleixner: "A set of updates for clocksource and clockevent drivers: - A fix for the prescaler of the ARM global timer where the prescaler mask define only covered 4 bits while it is actully 8 bits wide. This obviously restricted the possible range of prescaler adjustments - A fix for the RISC-V timer which prevents a timer interrupt being raised while the timer is initialized - A set of device tree updates to support new system on chips in various drivers - Kernel-doc and other cleanups all over the place" * tag 'timers-core-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: clocksource/drivers/timer-riscv: Clear timer interrupt on timer initialization dt-bindings: timer: Add support for cadence TTC PWM clocksource/drivers/arm_global_timer: Simplify prescaler register access clocksource/drivers/arm_global_timer: Guard against division by zero clocksource/drivers/arm_global_timer: Make gt_target_rate unsigned long dt-bindings: timer: add Ralink SoCs system tick counter clocksource: arm_global_timer: fix non-kernel-doc comment clocksource/drivers/arm_global_timer: Remove stray tab clocksource/drivers/arm_global_timer: Fix maximum prescaler value clocksource/drivers/imx-sysctr: Add i.MX95 support clocksource/drivers/imx-sysctr: Drop use global variables dt-bindings: timer: nxp,sysctr-timer: support i.MX95 dt-bindings: timer: renesas: ostm: Document RZ/Five SoC dt-bindings: timer: renesas,tmu: Document input capture interrupt clocksource/drivers/ti-32K: Fix misuse of "/**" comment clocksource/drivers/stm32: Fix all kernel-doc warnings dt-bindings: timer: exynos4210-mct: Add google,gs101-mct compatible clocksource/drivers/imx: Fix -Wunused-but-set-variable warning -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fixes from Thomas Gleixner: "A series of fixes for the Renesas RZG21 interrupt chip driver to prevent spurious and misrouted interrupts. - Ensure that posted writes are flushed in the eoi() callback - Ensure that interrupts are masked at the chip level when the trigger type is changed - Clear the interrupt status register when setting up edge type trigger modes - Ensure that the trigger type and routing information is set before the interrupt is enabled" * tag 'irq-urgent-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/renesas-rzg2l: Do not set TIEN and TINT source at the same time irqchip/renesas-rzg2l: Prevent spurious interrupts when setting trigger type irqchip/renesas-rzg2l: Rename rzg2l_irq_eoi() irqchip/renesas-rzg2l: Rename rzg2l_tint_eoi() irqchip/renesas-rzg2l: Flush posted write in irq_eoi() -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull core entry fix from Thomas Gleixner: "A single fix for the generic entry code: The trace_sys_enter() tracepoint can modify the syscall number via kprobes or BPF in pt_regs, but that requires that the syscall number is re-evaluted from pt_regs after the tracepoint. A seccomp fix in that area removed the re-evaluation so the change does not take effect as the code just uses the locally cached number. Restore the original behaviour by re-evaluating the syscall number after the tracepoint" * tag 'core-entry-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: entry: Respect changes to system call number by trace_sys_enter()
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull more powerpc updates from Michael Ellerman: - Handle errors in mark_rodata_ro() and mark_initmem_nx() - Make struct crash_mem available without CONFIG_CRASH_DUMP Thanks to Christophe Leroy and Hari Bathini. * tag 'powerpc-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/kdump: Split KEXEC_CORE and CRASH_DUMP dependency powerpc/kexec: split CONFIG_KEXEC_FILE and CONFIG_CRASH_DUMP kexec/kdump: make struct crash_mem available without CONFIG_CRASH_DUMP powerpc: Handle error in mark_rodata_ro() and mark_initmem_nx()
-
git://git.armlinux.org.uk/~rmk/linux-armLinus Torvalds authored
Pull ARM updates from Russell King: - remove a misuse of kernel-doc comment - use "Call trace:" for backtraces like other architectures - implement copy_from_kernel_nofault_allowed() to fix a LKDTM test - add a "cut here" line for prefetch aborts - remove unnecessary Kconfing entry for FRAME_POINTER - remove iwmmxy support for PJ4/PJ4B cores - use bitfield helpers in ptrace to improve readabililty - check if folio is reserved before flushing * tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: ARM: 9359/1: flush: check if the folio is reserved for no-mapping addresses ARM: 9354/1: ptrace: Use bitfield helpers ARM: 9352/1: iwmmxt: Remove support for PJ4/PJ4B cores ARM: 9353/1: remove unneeded entry for CONFIG_FRAME_POINTER ARM: 9351/1: fault: Add "cut here" line for prefetch aborts ARM: 9350/1: fault: Implement copy_from_kernel_nofault_allowed() ARM: 9349/1: unwind: Add missing "Call trace:" line ARM: 9334/1: mm: init: remove misuse of kernel-doc comment
-
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linuxLinus Torvalds authored
Pull more hardening updates from Kees Cook: - CONFIG_MEMCPY_SLOW_KUNIT_TEST is no longer needed (Guenter Roeck) - Fix needless UTF-8 character in arch/Kconfig (Liu Song) - Improve __counted_by warning message in LKDTM (Nathan Chancellor) - Refactor DEFINE_FLEX() for default use of __counted_by - Disable signed integer overflow sanitizer on GCC < 8 * tag 'hardening-v6.9-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: lkdtm/bugs: Improve warning message for compilers without counted_by support overflow: Change DEFINE_FLEX to take __counted_by member Revert "kunit: memcpy: Split slow memcpy tests into MEMCPY_SLOW_KUNIT_TEST" arch/Kconfig: eliminate needless UTF-8 character in Kconfig help ubsan: Disable signed integer overflow sanitizer on GCC < 8
-
Thomas Gleixner authored
The APIC address is registered twice. First during the early detection and afterwards when actually scanning the table for APIC IDs. The APIC and topology core warn about the second attempt. Restrict it to the early detection call. Fixes: 81287ad6 ("x86/apic: Sanitize APIC address setup") Signed-off-by:
Borislav Petkov (AMD) <bp@alien8.de> Tested-by:
Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20240322185305.297774848@linutronix.de
-
Thomas Gleixner authored
If there is no local APIC enumerated and registered then the topology bitmaps are empty. Therefore, topology_init_possible_cpus() will die with a division by zero exception. Prevent this by registering a fake APIC id to populate the topology bitmap. This also allows to use all topology query interfaces unconditionally. It does not affect the actual APIC code because either the local APIC address was not registered or no local APIC could be detected. Fixes: f1f758a8 ("x86/topology: Add a mechanism to track topology via APIC IDs") Reported-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Thomas Gleixner authored
The local APICs have not yet been enumerated so the logical ID evaluation from the topology bitmaps does not work and would return an error code. Skip the evaluation during the early boot CPUID evaluation and only apply it on the final run. Fixes: 380414be ("x86/cpu/topology: Use topology logical mapping mechanism") Signed-off-by:
-
Thomas Gleixner authored
The boot sequence evaluates CPUID information twice: 1) During early boot 2) When finalizing the early setup right before mitigations are selected and alternatives are patched. In both cases the evaluation is stored in boot_cpu_data, but on UP the copying of boot_cpu_data to the per CPU info of the boot CPU happens between #1 and #2. So any update which happens in #2 is never propagated to the per CPU info instance. Consolidate the whole logic and copy boot_cpu_data right before applying alternatives as that's the point where boot_cpu_data is in it's final state and not supposed to change anymore. This also removes the voodoo mb() from smp_prepare_cpus_common() which had absolutely no purpose. Fixes: 71eb4893 ("x86/percpu: Cure per CPU madness on UP") Reported-by:
-
- 22 Mar, 2024 2 commits
-
-
Nathan Chancellor authored
The current message for telling the user that their compiler does not support the counted_by attribute in the FAM_BOUNDS test does not make much sense either grammatically or semantically. Fix it to make it correct in both aspects. Signed-off-by:
Nathan Chancellor <nathan@kernel.org> Reviewed-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://lore.kernel.org/r/20240321-lkdtm-improve-lack-of-counted_by-msg-v1-1-0fbf7481a29c@kernel.orgSigned-off-by:
Kees Cook <keescook@chromium.org>
-
Kees Cook authored
The norm should be flexible array structures with __counted_by annotations, so DEFINE_FLEX() is updated to expect that. Rename the non-annotated version to DEFINE_RAW_FLEX(), and update the few existing users. Additionally add selftests for the macros. Reviewed-by:
Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by:
-
