Remove BW160 and BW80+80 capability in mt7915.
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Money Wang<Money.Wang@mediatek.com>
Signed-off-by: MeiChia Chiu <MeiChia.Chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix typo MCU_UNI_CMD_POWER_CREL to MCU_UNI_CMD_POWER_CTRL.

Fixes: 779d34de ("wifi: mt76: connac: add more unified command IDs")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use the sts variable when setting vht beamform sts cap.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

In newer chipsets, CFEND_RATE setting has been moved to different hw
module.

Fixes: 98686cd2 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix per-band chainmask when restoring from the dev chainmask.

Fixes: 98686cd2 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This reports signal strength of ACK packets from the peer as measured
at each interface.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When the chanctx enabled, IEEE80211_CONF_CHANGE_CHANNEL in .config()
would not be called anymore. mt76 cannot control RF channel for monitor.
Add monitor type set-channel flow in .change_chanctx().

Fixes: 41ac53c8 ("wifi: mt76: mt7921: introduce chanctx support")
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When flash mode is enabled, and the eeprom data in the flash is not for
the current chipset, it'll still be checked valid, and the default
eeprom bin won't be loaded.
(e.g., mt7915 NIC inserted with mt7916 eeprom data in the flash.)

Fix this kind of case by adding chip id into consideration in
mt7915_check_eeprom().
Reported-by: Cheng-Ji Li <cheng-ji.li@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add dev_err so that it is easier to see invalid setting while looking at
dmesg.
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Call mt7915_mcu_set_thermal_protect() through
mt7915_thermal_temp_store() to update firmware trigger/restore temp
directly.

Fixes: 02ee68b9 ("mt76: mt7915: add control knobs for thermal throttling")
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This patch includes 2 changes:
1. Firmware expects to disable thermal protect first before
reconfiguring.
2. Separate setting thermal_protect and setting thermal_tx_duty into
different functions. These two firmware commands do not need to send
together.

Fixes: 34b877d9 ("mt76: mt7915: add thermal cooling device support")
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Enable thermal management by default shall not be executed during mcu
init. This causes thermal configuration being reset to the firmware
default settings.

Fixes: 0063b86c ("mt76: mt7915e: Enable thermal management by default")
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When mt7921_abort_roc is called with dev->mutex held, it can deadlock while
calling cancel_work_sync(&phy->roc_work), because the work function could
be waiting to acquire the mutex.

Fix this by flushing the work before taking the mutex
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Fixes: 034ae28b ("wifi: mt76: mt7921: introduce remain_on_channel support")
Fixes: 41ac53c8 ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Frank Sae says:

====================
net: add dts for yt8521 and yt8531s, add driver for yt8531

Add dts for yt8521 and yt8531s, add driver for yt8531.
 These patches have been verified on our AM335x platform (motherboard)
 which has one integrated yt8521 and one RGMII interface.
 It can connect to daughter boards like yt8531s or yt8531 board.

 v5:
 - change the compatible of yaml
 - change the maintainers of yaml from "frank sae" to "Frank Sae"

 v4:
 - change default tx delay from 150ps to 1950ps
 - add compatible for yaml

 v3:
 - change default rx delay from 1900ps to 1950ps
 - moved ytphy_rgmii_clk_delay_config_with_lock from yt8521's patch to yt8531's patch
 - removed unnecessary checks of phydev->attached_dev->dev_addr

 v2:
 - split BIT macro as one patch
 - split "dts for yt8521/yt8531s ... " patch as two patches
 - use standard rx-internal-delay-ps and tx-internal-delay-ps, removed motorcomm,sds-tx-amplitude
 - removed ytphy_parse_dt, ytphy_probe_helper and ytphy_config_init_helper
 - not store dts arg to yt8521_priv
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have
 verified the driver on AM335x platform with yt8531 board. On the
 board, yt8531 gigabit ethernet phy works in utp mode, RGMII
 interface, supports 1000M/100M/10M speeds, and wol(magic package).
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dts support for Motorcomm yt8531s gigabit ethernet phy.
 Change yt8521_probe to support clk config of yt8531s. Becase
 yt8521_probe does the things which yt8531s is needed, so
 removed yt8531s function.
 This patch has been verified on AM335x platform with yt8531s board.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dts support for Motorcomm yt8521 gigabit ethernet phy.
 Add ytphy_rgmii_clk_delay_config function to support dst config for
 the delay of rgmii clk. This funciont is common for yt8521, yt8531s
 and yt8531.
 This patch has been verified on AM335x platform.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add BIT macro for Motorcomm yt8521/yt8531 gigabit ethernet phy.
 This is a preparatory patch. Add BIT macro for 0xA012 reg, and
 supplement for 0xA001 and 0xA003 reg. These will be used to support dts.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a YAML binding document for the Motorcomm yt8xxx Ethernet phy.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vlad Buslov says:

====================
net: Allow offloading of UDP NEW connections via act_ct

Currently only bidirectional established connections can be offloaded
via act_ct. Such approach allows to hardcode a lot of assumptions into
act_ct, flow_table and flow_offload intermediate layer codes. In order
to enabled offloading of unidirectional UDP NEW connections start with
incrementally changing the following assumptions:

- Drivers assume that only established connections are offloaded and
  don't support updating existing connections. Extract ctinfo from meta
  action cookie and refuse offloading of new connections in the drivers.

- Fix flow_table offload fixup algorithm to calculate flow timeout
  according to current connection state instead of hardcoded
  "established" value.

- Add new flow_table flow flag that designates bidirectional connections
  instead of assuming it and hardcoding hardware offload of every flow
  in both directions.

- Add new flow_table flow flag that designates connections that are
  offloaded to hardware as "established" instead of assuming it. This
  allows some optimizations in act_ct and prevents spamming the
  flow_table workqueue with redundant tasks.

With all the necessary infrastructure in place modify act_ct to offload
UDP NEW as unidirectional connection. Pass reply direction traffic to CT
and promote connection to bidirectional when UDP connection state
changes to "assured". Rely on refresh mechanism to propagate connection
state change to supporting drivers.

Note that early drop algorithm that is designed to free up some space in
connection tracking table when it becomes full (by randomly deleting up
to 5% of non-established connections) currently ignores connections
marked as "offloaded". Now, with UDP NEW connections becoming
"offloaded" it could allow malicious user to perform DoS attack by
filling the table with non-droppable UDP NEW connections by sending just
one packet in single direction. To prevent such scenario change early
drop algorithm to also consider "offloaded" connections for deletion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Both synchronous early drop algorithm and asynchronous gc worker completely
ignore connections with IPS_OFFLOAD_BIT status bit set. With new
functionality that enabled UDP NEW connection offload in action CT
malicious user can flood the conntrack table with offloaded UDP connections
by just sending a single packet per 5tuple because such connections can no
longer be deleted by early drop algorithm.

To mitigate the issue allow both early drop and gc to consider offloaded
UDP connections for deletion.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify the offload algorithm of UDP connections to the following:

- Offload NEW connection as unidirectional.

- When connection state changes to ESTABLISHED also update the hardware
flow. However, in order to prevent act_ct from spamming offload add wq for
every packet coming in reply direction in this state verify whether
connection has already been updated to ESTABLISHED in the drivers. If that
it the case, then skip flow_table and let conntrack handle such packets
which will also allow conntrack to potentially promote the connection to
ASSURED.

- When connection state changes to ASSURED set the flow_table flow
NF_FLOW_HW_BIDIRECTIONAL flag which will cause refresh mechanism to offload
the reply direction.

All other protocols have their offload algorithm preserved and are always
offloaded as bidirectional.

Note that this change tries to minimize the load on flow_table add
workqueue. First, it tracks the last ctinfo that was offloaded by using new
flow 'NF_FLOW_HW_ESTABLISHED' flag and doesn't schedule the refresh for
reply direction packets when the offloads have already been updated with
current ctinfo. Second, when 'add' task executes on workqueue it always
update the offload with current flow state (by checking 'bidirectional'
flow flag and obtaining actual ctinfo/cookie through meta action instead of
caching any of these from the moment of scheduling the 'add' work)
preventing the need from scheduling more updates if state changed
concurrently while the 'add' work was pending on workqueue.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently tcf_ct_flow_table_fill_actions() function assumes that only
established connections can be offloaded and always sets ctinfo to either
IP_CT_ESTABLISHED or IP_CT_ESTABLISHED_REPLY strictly based on direction
without checking actual connection state. To enable UDP NEW connection
offload set the ctinfo, metadata cookie and NF_FLOW_HW_ESTABLISHED
flow_offload flags bit based on ct->status value.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify flow table offload to cache the last ct info status that was passed
to the driver offload callbacks by extending enum nf_flow_flags with new
"NF_FLOW_HW_ESTABLISHED" flag. Set the flag if ctinfo was 'established'
during last act_ct meta actions fill call. This infrastructure change is
necessary to optimize promoting of UDP connections from 'new' to
'established' in following patches in this series.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify flow table offload to support unidirectional connections by
extending enum nf_flow_flags with new "NF_FLOW_HW_BIDIRECTIONAL" flag. Only
offload reply direction when the flag is set. This infrastructure change is
necessary to support offloading UDP NEW connections in original direction
in following patches in series.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently flow_offload_fixup_ct() function assumes that only replied UDP
connections can be offloaded and hardcodes UDP_CT_REPLIED timeout value. To
enable UDP NEW connection offload in following patches extract the actual
connections state from ct->status and set the timeout according to it.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to offload connections in other states besides "established" the
driver offload callbacks need to have access to connection conntrack info.
Flow offload intermediate representation data structure already contains
that data encoded in 'cookie' field, so just reuse it in the drivers.

Reject offloading IP_CT_NEW connections for now by returning an error in
relevant driver callbacks based on value of ctinfo. Support for offloading
such connections will need to be added to the drivers afterwards.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable debugfs for vcap for lan966x. This will allow to print all the
entries in the VCAP and also the port information regarding which keys
are configured.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yoshihiro Shimoda says:

====================
net: renesas: rswitch: Modify initialization for SERDES and PHY

- My platform has the 88x2110.
- The MACTYPE setting of strap pin on the platform is SXGMII.
- However, we realized that the SoC cannot communicate the PHY with SXGMII
  because of mismatching hardware specification.
- We have a lot of boards which mismatch the MACTYPE setting.

So, I would like to change the MACTYPE as SGMII by software for the platform.

The patch [1/5] sets phydev->host_interfaces by phylink for Marvell PHY
driver (marvell10g) to initialize the MACTYPE.

- The patch [1/5] siplifies the rswitch driver.
- The patch [2/5] converts to phy_device from phylink.
- The patch [3/5] sets phydev->host_interfaces from this driver without
  any new functions of phylib.
- The patch [4/5] adds phy_power_on() calling to initialize the Ethernet
  SERDES PHY driver (r8a779f0-eth-serdes) for each channel.
- The patch [5/5] adds "max-speed" handling.

Changes from v4:
https://lore.kernel.org/all/20230127142621.1761278-1-yoshihiro.shimoda.uh@renesas.com/
 - No modification of phylink API.
 - Convert to phylib instead of phylink.
 - Add "max-speed" handling.

Changes from v3:
https://lore.kernel.org/all/20230127014812.1656340-1-yoshihiro.shimoda.uh@renesas.com/
 - Keep a pointer of "port" and more simplify the code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous code set the speed by the interface mode of PHY.
Also this hardware has a restriction which cannot change the speed
at runtime. To use other speed, add "max-speed" handling to set
each port's speed if needed.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Ethernet PHYs (like marvell10g) will decide the host interface
mode by the media-side speed. So, the rswitch driver needs to
initialize one of the Ethernet SERDES (r8a779f0-eth-serdes) ports
after linked the Ethernet PHY up. The r8a779f0-eth-serdes driver has
.init() for initializing all ports and .power_on() for initializing
each port. So, add phy_power_{on,off} calling for it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set phydev->host_interfaces before calling of_phy_connect() to
configure the PHY with the information of host_interfaces.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Intended to set phy_device->host_interfaces by phylink in the future.
But there is difficult to implement phylink properly, especially
supporting the in-band mode on this driver because extra initialization
is needed after linked the ethernet PHY up. So, convert to phy_device
from phylink.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify struct phy *serdes handling by keeping the valiable in
the struct rswitch_device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the unlikely case incoming packets are dropped because
of IP_MINTTL / IPV6_MINHOPCOUNT constraints...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230201174345.2708943-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Conversion to gpiod API done in commit 468ba54b ("fec: convert
to gpio descriptor") clashed with gpiolib applying the same quirk to the
reset GPIO polarity (introduced in commit b02c85c9). This results in
the reset line being left active/device being left in reset state when
reset line is "active low".

Remove handling of 'phy-reset-active-high' property from the driver and
rely on gpiolib to apply needed adjustments to avoid ending up with the
double inversion/flipped logic.

Fixes: 468ba54b ("fec: convert to gpio descriptor")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230201215320.528319-2-dmitry.torokhov@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Conversion of the driver to gpiod API done in 468ba54b ("fec:
convert to gpio descriptor") incorrectly made reset line mandatory and
resulted in aborting driver probe in cases where reset line was not
specified (note: this way of specifying PHY reset line is actually
deprecated).

Switch to using devm_gpiod_get_optional() and skip manipulating reset
line if it can not be located.

Fixes: 468ba54b ("fec: convert to gpio descriptor")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230201215320.528319-1-dmitry.torokhov@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

net/core/gro.c
  7d2c89b3 ("skb: Do mix page pool and page referenced frags in GRO")
  b1a78b9b ("net: add support for ipv4 big tcp")
https://lore.kernel.org/all/20230203094454.5766f160@canb.auug.org.au/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf, can and netfilter.

  Current release - regressions:

   - phy: fix null-deref in phy_attach_direct

   - mac802154: fix possible double free upon parsing error

  Previous releases - regressions:

   - bpf: preserve reg parent/live fields when copying range info,
     prevent mis-verification of programs as safe

   - ip6: fix GRE tunnels not generating IPv6 link local addresses

   - phy: dp83822: fix null-deref on DP83825/DP83826 devices

   - sctp: do not check hb_timer.expires when resetting hb_timer

   - eth: mtk_sock: fix SGMII configuration after phylink conversion

  Previous releases - always broken:

   - eth: xdp: execute xdp_do_flush() before napi_complete_done()

   - skb: do not mix page pool and page referenced frags in GRO

   - bpf:
      - fix a possible task gone issue with bpf_send_signal[_thread]()
      - fix an off-by-one bug in bpf_mem_cache_idx() to select the right
        cache
      - add missing btf_put to register_btf_id_dtor_kfuncs
      - sockmap: fon't let sock_map_{close,destroy,unhash} call itself

   - gso: fix null-deref in skb_segment_list()

   - mctp: purge receive queues on sk destruction

   - fix UaF caused by accept on already connected socket in exotic
     socket families

   - tls: don't treat list head as an entry in tls_is_tx_ready()

   - netfilter: br_netfilter: disable sabotage_in hook after first
     suppression

   - wwan: t7xx: fix runtime PM implementation

  Misc:

   - MAINTAINERS: spring cleanup of networking maintainers"

* tag 'net-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
  mtk_sgmii: enable PCS polling to allow SFP work
  net: mediatek: sgmii: fix duplex configuration
  net: mediatek: sgmii: ensure the SGMII PHY is powered down on configuration
  MAINTAINERS: update SCTP maintainers
  MAINTAINERS: ipv6: retire Hideaki Yoshifuji
  mailmap: add John Crispin's entry
  MAINTAINERS: bonding: move Veaceslav Falico to CREDITS
  net: openvswitch: fix flow memory leak in ovs_flow_cmd_new
  net: ethernet: mtk_eth_soc: disable hardware DSA untagging for second MAC
  virtio-net: Keep stop() to follow mirror sequence of open()
  selftests: net: udpgso_bench_tx: Cater for pending datagrams zerocopy benchmarking
  selftests: net: udpgso_bench: Fix racing bug between the rx/tx programs
  selftests: net: udpgso_bench_rx/tx: Stop when wrong CLI args are provided
  selftests: net: udpgso_bench_rx: Fix 'used uninitialized' compiler warning
  can: mcp251xfd: mcp251xfd_ring_set_ringparam(): assign missing tx_obj_num_coalesce_irq
  can: isotp: split tx timer into transmission and timeout
  can: isotp: handle wait_event_interruptible() return values
  can: raw: fix CAN FD frame transmissions over CAN XL devices
  can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
  hv_netvsc: Fix missed pagebuf entries in netvsc_dma_map/unmap()
  ...

Merge tag 'linux-kselftest-kunit-fixes-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull KUnit fixes from Shuah Khan:
 "Three fixes to bugs that cause kernel crash, link error during build,
  and a third to fix kunit_test_init_section_suites() extra indirection
  issue"

* tag 'linux-kselftest-kunit-fixes-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  kunit: fix kunit_test_init_section_suites(...)
  kunit: fix bug in KUNIT_EXPECT_MEMEQ
  kunit: Export kunit_running()