- 24 Apr, 2020 34 commits
-
-
Thomas Gleixner authored
commit 3d51507f upstream. All exception entry points must have ASM_CLAC right at the beginning. The general_protection entry is missing one. Fixes: e59d1b0a ("x86-32, smap: Add STAC/CLAC instructions to 32-bit kernel entry") Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Frederic Weisbecker <frederic@kernel.org> Reviewed-by:
Alexandre Chartre <alexandre.chartre@oracle.com> Reviewed-by:
Andy Lutomirski <luto@kernel.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200225220216.219537887@linutronix.deSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric W. Biederman authored
commit d1e7fd64 upstream. Replace the 32bit exec_id with a 64bit exec_id to make it impossible to wrap the exec_id counter. With care an attacker can cause exec_id wrap and send arbitrary signals to a newly exec'd parent. This bypasses the signal sending checks if the parent changes their credentials during exec. The severity of this problem can been seen that in my limited testing of a 32bit exec_id it can take as little as 19s to exec 65536 times. Which means that it can take as little as 14 days to wrap a 32bit exec_id. Adam Zabrocki has succeeded wrapping the self_exe_id in 7 days. Even my slower timing is in the uptime of a typical server. Which means self_exec_id is simply a speed bump today, and if exec gets noticably faster self_exec_id won't even be a speed bump. Extending self_exec_id to 64bits introduces a problem on 32bit architectures where reading self_exec_id is no longer atomic and can take two read instructions. Which means that is is possible to hit a window where the read value of exec_id does not match the written value. So with very lucky timing after this change this still remains expoiltable. I have updated the update of exec_id on exec to use WRITE_ONCE and the read of exec_id in do_notify_parent to use READ_ONCE to make it clear that there is no locking between these two locations. Link: https://lore.kernel.org/kernel-hardening/20200324215049.GA3710@pi3.com.pl Fixes: 2.3.23pre2 Cc: stable@vger.kernel.org Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Remi Pommarel authored
commit 968ae2ca upstream. When TPC is disabled IEEE80211_CONF_CHANGE_POWER event can be handled to reconfigure HW's maximum txpower. This fixes 0dBm txpower setting when user attaches to an interface for the first time with the following scenario: ieee80211_do_open() ath9k_add_interface() ath9k_set_txpower() /* Set TX power with not yet initialized sc->hw->conf.power_level */ ieee80211_hw_config() /* Iniatilize sc->hw->conf.power_level and raise IEEE80211_CONF_CHANGE_POWER */ ath9k_config() /* IEEE80211_CONF_CHANGE_POWER is ignored */ This issue can be reproduced with the following: $ modprobe -r ath9k $ modprobe ath9k $ wpa_supplicant -i wlan0 -c /tmp/wpa.conf & $ iw dev /* Here TX power is either 0 or 3 depending on RF chain */ $ killall wpa_supplicant $ iw dev /* TX power goes back to calibrated value and subsequent calls will be fine */ Fixes: 283dd119 ("ath9k: add per-vif TX power capability") Cc: stable@vger.kernel.org Signed-off-by:
Remi Pommarel <repk@triplefau.lt> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Gustavo A. R. Silva authored
commit 792a402c upstream. There is a potential NULL pointer dereference in case kzalloc() fails and returns NULL. Fix this by adding a NULL check on *cd* This bug was detected with the help of Coccinelle. Fixes: 64b139f9 ("MIPS: OCTEON: irq: add CIB and other fixes") Cc: stable@vger.kernel.org Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by:
-
Sungbo Eo authored
commit 6a214a28 upstream. Clear its own IRQs before the parent IRQ get enabled, so that the remaining IRQs do not accidentally interrupt the parent IRQ controller. This patch also fixes a reboot bug on OX820 SoC, where the remaining rps-timer IRQ raises a GIC interrupt that is left pending. After that, the rps-timer IRQ is cleared during driver initialization, and there's no IRQ left in rps-irq when local_irq_enable() is called, which evokes an error message "unexpected IRQ trap". Fixes: bdd272cb ("irqchip: versatile FPGA: support cascaded interrupts from DT") Signed-off-by:
Sungbo Eo <mans0n@gorani.run> Signed-off-by:
Marc Zyngier <maz@kernel.org> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200321133842.2408823-1-mans0n@gorani.runSigned-off-by:
-
Yang Xu authored
commit 2e356101 upstream. Currently, when we add a new user key, the calltrace as below: add_key() key_create_or_update() key_alloc() __key_instantiate_and_link generic_key_instantiate key_payload_reserve ...... Since commit a08bf91c ("KEYS: allow reaching the keys quotas exactly"), we can reach max bytes/keys in key_alloc, but we forget to remove this limit when we reserver space for payload in key_payload_reserve. So we can only reach max keys but not max bytes when having delta between plen and type->def_datalen. Remove this limit when instantiating the key, so we can keep consistent with key_alloc. Also, fix the similar problem in keyctl_chown_key(). Fixes: 0b77f5bf ("keys: make the keyring quotas controllable through /proc/sys") Fixes: a08bf91c ("KEYS: allow reaching the keys quotas exactly") Cc: stable@vger.kernel.org # 5.0.x Cc: Eric Biggers <ebiggers@google.com> Signed-off-by:
Yang Xu <xuyang2018.jy@cn.fujitsu.com> Reviewed-by:
Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
-
Martin Blumenstingl authored
commit 3f5b9959 upstream. When CONFIG_DEVFREQ_THERMAL is disabled all functions except of_devfreq_cooling_register_power() were already inlined. Also inline the last function to avoid compile errors when multiple drivers call of_devfreq_cooling_register_power() when CONFIG_DEVFREQ_THERMAL is not set. Compilation failed with the following message: multiple definition of `of_devfreq_cooling_register_power' (which then lists all usages of of_devfreq_cooling_register_power()) Thomas Zimmermann reported this problem [0] on a kernel config with CONFIG_DRM_LIMA={m,y}, CONFIG_DRM_PANFROST={m,y} and CONFIG_DEVFREQ_THERMAL=n after both, the lima and panfrost drivers gained devfreq cooling support. [0] https://www.spinics.net/lists/dri-devel/msg252825.html Fixes: a76caf55 ("thermal: Add devfreq cooling") Cc: stable@vger.kernel.org Reported-by:
Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200403205133.1101808-1-martin.blumenstingl@googlemail.comSigned-off-by:
-
Jan Engelhardt authored
commit ecb9c790 upstream. The value in "new" is constructed from "old" such that all bits defined as reserved by the ACPI spec[1] are left untouched. But if those bits do not happen to be all zero, "new < 3" will not evaluate to true. The firmware of the laptop(s) Medion MD63490 / Akoya P15648 comes with garbage inside the "FACS" ACPI table. The starting value is old=0x4944454d, therefore new=0x4944454e, which is >= 3. Mask off the reserved bits. [1] https://uefi.org/sites/default/files/resources/ACPI_6_2.pdf Link: https://bugzilla.kernel.org/show_bug.cgi?id=206553 Cc: All applicable <stable@vger.kernel.org> Signed-off-by:
Jan Engelhardt <jengelh@inai.de> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Benoit Parrot authored
commit 1db56284 upstream. disable_irqs() was mistakenly disabling all interrupts when called. This cause all port stream to stop even if only stopping one of them. Cc: stable <stable@vger.kernel.org> Signed-off-by:
Benoit Parrot <bparrot@ti.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit ae769d35 upstream. The recent fix for the OOB access in PCM OSS plugins (commit f2ecf903: "ALSA: pcm: oss: Avoid plugin buffer overflow") caused a regression on OSS applications. The patch introduced the size check in client and slave size calculations to limit to each plugin's buffer size, but I overlooked that some code paths call those without allocating the buffer but just for estimation. This patch fixes the bug by skipping the size check for those code paths while keeping checking in the actual transfer calls. Fixes: f2ecf903 ("ALSA: pcm: oss: Avoid plugin buffer overflow") Tested-and-reported-by:
Jari Ruusu <jari.ruusu@gmail.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200403072515.25539-1-tiwai@suse.deSigned-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit c47914c0 upstream. The access to Analog Capture Source control value implemented in prodigy_hifi.c is wrong, as caught by the recently introduced sanity check; it should be accessing value.enumerated.item[] instead of value.integer.value[]. This patch corrects the wrong access pattern. Fixes: 6b8d6e55 ("[ALSA] ICE1724: Added support for Audiotrak Prodigy 7.1 HiFi & HD2, Hercules Fortissimo IV") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207139Reviewed-by:
Jaroslav Kysela <perex@perex.cz> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200407084402.25589-3-tiwai@suse.deSigned-off-by:
-
Takashi Iwai authored
commit 0ad3f0b3 upstream. The beep control helper function blindly stores the values in two stereo channels no matter whether the actual control is mono or stereo. This is practically harmless, but it annoys the recently introduced sanity check, resulting in an error when the checker is enabled. This patch corrects the behavior to store only on the defined array member. Fixes: 0401e854 ("ALSA: hda - Move beep helper functions to hda_beep.c") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207139Reviewed-by:
-
Takashi Iwai authored
commit 3c6fd1f0 upstream. The recent AMD platform exposes an HD-audio bus but without any actual codecs, which is internally tied with a USB-audio device, supposedly. It results in "no codecs" error of HD-audio bus driver, and it's nothing but a waste of resources. This patch introduces a static blacklist table for skipping such a known bogus PCI SSID entry. As of writing this patch, the known SSIDs are: * 1043:874f - ASUS ROG Zenith II / Strix * 1462:cb59 - MSI TRX40 Creator * 1462:cb60 - MSI TRX40 BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206543 Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200408140449.22319-2-tiwai@suse.deSigned-off-by:
-
Takashi Iwai authored
commit 2a48218f upstream. Some recent boards (supposedly with a new AMD platform) contain the USB audio class 2 device that is often tied with HD-audio. The device exposes an Input Gain Pad control (id=19, control=12) but this node doesn't behave correctly, returning an error for each inquiry of GET_MIN and GET_MAX that should have been mandatory. As a workaround, simply ignore this node by adding a usbmix_name_map table entry. The currently known devices are: * 0414:a002 - Gigabyte TRX40 Aorus Pro WiFi * 0b05:1916 - ASUS ROG Zenith II * 0b05:1917 - ASUS ROG Strix * 0db0:0d64 - MSI TRX40 Creator * 0db0:543d - MSI TRX40 BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206543 Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200408140449.22319-1-tiwai@suse.deSigned-off-by:
-
Thinh Nguyen authored
commit 5e5caf4f upstream. Different configuration/condition may draw different power. Inform the controller driver of the change so it can respond properly (e.g. GET_STATUS request). This fixes an issue with setting MaxPower from configfs. The composite driver doesn't check this value when setting self-powered. Cc: stable@vger.kernel.org Fixes: 88af8bbe ("usb: gadget: the start of the configfs interface") Signed-off-by:
Thinh Nguyen <thinhn@synopsys.com> Signed-off-by:
Felipe Balbi <balbi@kernel.org> Signed-off-by:
-
Sriharsha Allenki authored
commit f63ec55f upstream. In AIO case, the request is freed up if ep_queue fails. However, io_data->req still has the reference to this freed request. In the case of this failure if there is aio_cancel call on this io_data it will lead to an invalid dequeue operation and a potential use after free issue. Fix this by setting the io_data->req to NULL when the request is freed as part of queue failure. Fixes: 2e4c7553 ("usb: gadget: f_fs: add aio support") Signed-off-by:
Sriharsha Allenki <sallenki@codeaurora.org> CC: stable <stable@vger.kernel.org> Reviewed-by:
Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/r/20200326115620.12571-1-sallenki@codeaurora.orgSigned-off-by:
-
이경택 authored
commit abca9e4a upstream. Current topology doesn't add prefix of component to new kcontrol. Signed-off-by:
Gyeongtaek Lee <gt82.lee@samsung.com> Link: https://lore.kernel.org/r/009b01d60804$ae25c2d0$0a714870$@samsung.comSigned-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
이경택 authored
commit 21fca8bd upstream. soc_compr_trigger_fe() allows start or stop after pause_push. In dpcm_be_dai_trigger(), however, only pause_release is allowed command after pause_push. So, start or stop after pause in compress offload is always returned as error if the compress offload is used with dpcm. To fix the problem, SND_SOC_DPCM_STATE_PAUSED should be allowed for start or stop command. Signed-off-by:
Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/004d01d607c1$7a3d5250$6eb7f6f0$@samsung.comSigned-off-by:
-
이경택 authored
commit 3bbbb772 upstream. Since a virtual mixer has no backing registers to decide which path to connect, it will try to match with initial state. This is to ensure that the default mixer choice will be correctly powered up during initialization. Invert flag is used to select initial state of the virtual switch. Since actual hardware can't be disconnected by virtual switch, connected is better choice as initial state in many cases. Signed-off-by:
-
이경택 authored
commit 0ab07091 upstream. If regwshift is 32 and the selected architecture compiles '<<' operator for signed int literal into rotating shift, '1<<regwshift' became 1 and it makes regwmask to 0x0. The literal is set to unsigned long to get intended regwmask. Signed-off-by:
-
YueHaibing authored
[ Upstream commit 10cea23b ] rts522a should use rts522a_pcr_ops, which is diffrent with rts5227 in phy/hw init setting. Fixes: ce6a5acc ("mfd: rtsx: Add support for rts522A") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200326032618.20472-1-yuehaibing@huawei.comSigned-off-by:
Sasha Levin <sashal@kernel.org>
-
Josef Bacik authored
[ Upstream commit ea287ab1 ] We always search the commit root of the extent tree for looking up back references, however we track the reloc roots based on their current bytenr. This is wrong, if we commit the transaction between relocating tree blocks we could end up in this code in build_backref_tree if (key.objectid == key.offset) { /* * Only root blocks of reloc trees use backref * pointing to itself. */ root = find_reloc_root(rc, cur->bytenr); ASSERT(root); cur->root = root; break; } find_reloc_root() is looking based on the bytenr we had in the commit root, but if we've COWed this reloc root we will not find that bytenr, and we will trip over the ASSERT(root). Fix this by using the commit_root->start bytenr for indexing the commit root. Then we change the __update_reloc_root() caller to be used when we switch the commit root for the reloc root during commit. This fixes the panic I was seeing when we started throttling relocation for delayed refs. Signed-off-by:
Josef Bacik <josef@toxicpanda.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Josef Bacik authored
[ Upstream commit 7b7b7431 ] This was pretty subtle, we default to reloc roots having 0 root refs, so if we crash in the middle of the relocation they can just be deleted. If we successfully complete the relocation operations we'll set our root refs to 1 in prepare_to_merge() and then go on to merge_reloc_roots(). At prepare_to_merge() time if any of the reloc roots have a 0 reference still, we will remove that reloc root from our reloc root rb tree, and then clean it up later. However this only happens if we successfully start a transaction. If we've aborted previously we will skip this step completely, and only have reloc roots with a reference count of 0, but were never properly removed from the reloc control's rb tree. This isn't a problem per-se, our references are held by the list the reloc roots are on, and by the original root the reloc root belongs to. If we end up in this situation all the reloc roots will be added to the dirty_reloc_list, and then properly dropped at that point. The reloc control will be free'd and the rb tree is no longer used. There were two options when fixing this, one was to remove the BUG_ON(), the other was to make prepare_to_merge() handle the case where we couldn't start a trans handle. IMO this is the cleaner solution. I started with handling the error in prepare_to_merge(), but it turned out super ugly. And in the end this BUG_ON() simply doesn't matter, the cleanup was happening properly, we were just panicing because this BUG_ON() only matters in the success case. So I've opted to just remove it and add a comment where it was. Reviewed-by:
Qu Wenruo <wqu@suse.com> Signed-off-by:
-
Boqun Feng authored
[ Upstream commit 25016bd7 ] Qian Cai reported a bug when PROVE_RCU_LIST=y, and read on /proc/lockdep triggered a warning: [ ] DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled) ... [ ] Call Trace: [ ] lock_is_held_type+0x5d/0x150 [ ] ? rcu_lockdep_current_cpu_online+0x64/0x80 [ ] rcu_read_lock_any_held+0xac/0x100 [ ] ? rcu_read_lock_held+0xc0/0xc0 [ ] ? __slab_free+0x421/0x540 [ ] ? kasan_kmalloc+0x9/0x10 [ ] ? __kmalloc_node+0x1d7/0x320 [ ] ? kvmalloc_node+0x6f/0x80 [ ] __bfs+0x28a/0x3c0 [ ] ? class_equal+0x30/0x30 [ ] lockdep_count_forward_deps+0x11a/0x1a0 The warning got triggered because lockdep_count_forward_deps() call __bfs() without current->lockdep_recursion being set, as a result a lockdep internal function (__bfs()) is checked by lockdep, which is unexpected, and the inconsistency between the irq-off state and the state traced by lockdep caused the warning. Apart from this warning, lockdep internal functions like __bfs() should always be protected by current->lockdep_recursion to avoid potential deadlocks and data inconsistency, therefore add the current->lockdep_recursion on-and-off section to protect __bfs() in both lockdep_count_forward_deps() and lockdep_count_backward_deps() Reported-by:
Qian Cai <cai@lca.pw> Signed-off-by:
Boqun Feng <boqun.feng@gmail.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20200312151258.128036-1-boqun.feng@gmail.comSigned-off-by:
-
Arvind Sankar authored
[ Upstream commit 81a34892 ] The load address is compared with LOAD_PHYSICAL_ADDR using a signed comparison currently (using jge instruction). When loading a 64-bit kernel using the new efi32_pe_entry() point added by: 97aa2765 ("efi/x86: Add true mixed mode entry point into .compat section") using Qemu with -m 3072, the firmware actually loads us above 2Gb, resulting in a very early crash. Use the JAE instruction to perform a unsigned comparison instead, as physical addresses should be considered unsigned. Signed-off-by:
Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by:
Ard Biesheuvel <ardb@kernel.org> Signed-off-by:
Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20200301230436.2246909-6-nivedita@alum.mit.edu Link: https://lore.kernel.org/r/20200308080859.21568-14-ardb@kernel.orgSigned-off-by:
-
Bob Peterson authored
[ Upstream commit df5db5f9 ] Before this patch, run_queue would demote glocks based on whether there are any more holders. But if the glock has pending revokes that haven't been written to the media, giving up the glock might end in file system corruption if the revokes never get written due to io errors, node crashes and fences, etc. In that case, another node will replay the metadata blocks associated with the glock, but because the revoke was never written, it could replay that block even though the glock had since been granted to another node who might have made changes. This patch changes the logic in run_queue so that it never demotes a glock until its count of pending revokes reaches zero. Signed-off-by:
Bob Peterson <rpeterso@redhat.com> Reviewed-by:
Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by:
-
John Garry authored
[ Upstream commit 1d72f7ae ] If the call to scsi_add_host_with_dma() in ata_scsi_add_hosts() fails, then we may get use-after-free KASAN warns: ================================================================== BUG: KASAN: use-after-free in kobject_put+0x24/0x180 Read of size 1 at addr ffff0026b8c80364 by task swapper/0/1 CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 5.6.0-rc3-00004-g5a71b206ea82-dirty #1765 Hardware name: Huawei TaiShan 200 (Model 2280)/BC82AMDD, BIOS 2280-V2 CS V3.B160.01 02/24/2020 Call trace: dump_backtrace+0x0/0x298 show_stack+0x14/0x20 dump_stack+0x118/0x190 print_address_description.isra.9+0x6c/0x3b8 __kasan_report+0x134/0x23c kasan_report+0xc/0x18 __asan_load1+0x5c/0x68 kobject_put+0x24/0x180 put_device+0x10/0x20 scsi_host_put+0x10/0x18 ata_devres_release+0x74/0xb0 release_nodes+0x2d0/0x470 devres_release_all+0x50/0x78 really_probe+0x2d4/0x560 driver_probe_device+0x7c/0x148 device_driver_attach+0x94/0xa0 __driver_attach+0xa8/0x110 bus_for_each_dev+0xe8/0x158 driver_attach+0x30/0x40 bus_add_driver+0x220/0x2e0 driver_register+0xbc/0x1d0 __pci_register_driver+0xbc/0xd0 ahci_pci_driver_init+0x20/0x28 do_one_initcall+0xf0/0x608 kernel_init_freeable+0x31c/0x384 kernel_init+0x10/0x118 ret_from_fork+0x10/0x18 Allocated by task 5: save_stack+0x28/0xc8 __kasan_kmalloc.isra.8+0xbc/0xd8 kasan_kmalloc+0xc/0x18 __kmalloc+0x1a8/0x280 scsi_host_alloc+0x44/0x678 ata_scsi_add_hosts+0x74/0x268 ata_host_register+0x228/0x488 ahci_host_activate+0x1c4/0x2a8 ahci_init_one+0xd18/0x1298 local_pci_probe+0x74/0xf0 work_for_cpu_fn+0x2c/0x48 process_one_work+0x488/0xc08 worker_thread+0x330/0x5d0 kthread+0x1c8/0x1d0 ret_from_fork+0x10/0x18 Freed by task 5: save_stack+0x28/0xc8 __kasan_slab_free+0x118/0x180 kasan_slab_free+0x10/0x18 slab_free_freelist_hook+0xa4/0x1a0 kfree+0xd4/0x3a0 scsi_host_dev_release+0x100/0x148 device_release+0x7c/0xe0 kobject_put+0xb0/0x180 put_device+0x10/0x20 scsi_host_put+0x10/0x18 ata_scsi_add_hosts+0x210/0x268 ata_host_register+0x228/0x488 ahci_host_activate+0x1c4/0x2a8 ahci_init_one+0xd18/0x1298 local_pci_probe+0x74/0xf0 work_for_cpu_fn+0x2c/0x48 process_one_work+0x488/0xc08 worker_thread+0x330/0x5d0 kthread+0x1c8/0x1d0 ret_from_fork+0x10/0x18 There is also refcount issue, as well: WARNING: CPU: 1 PID: 1 at lib/refcount.c:28 refcount_warn_saturate+0xf8/0x170 The issue is that we make an erroneous extra call to scsi_host_put() for that host: So in ahci_init_one()->ata_host_alloc_pinfo()->ata_host_alloc(), we setup a device release method - ata_devres_release() - which intends to release the SCSI hosts: static void ata_devres_release(struct device *gendev, void *res) { ... for (i = 0; i < host->n_ports; i++) { struct ata_port *ap = host->ports[i]; if (!ap) continue; if (ap->scsi_host) scsi_host_put(ap->scsi_host); } ... } However in the ata_scsi_add_hosts() error path, we also call scsi_host_put() for the SCSI hosts. Fix by removing the the scsi_host_put() calls in ata_scsi_add_hosts() and leave this to ata_devres_release(). Fixes: f3187195 ("libata: separate out ata_host_alloc() and ata_host_register()") Signed-off-by:
John Garry <john.garry@huawei.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Andy Lutomirski authored
[ Upstream commit 630b99ab ] If AT_SYSINFO is not present, don't try to call a NULL pointer. Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/faaf688265a7e1a5b944d6f8bc0f6368158306d3.1584052409.git.luto@kernel.orgSigned-off-by:
-
Michael Wang authored
[ Upstream commit 26cf5222 ] During our testing, we found a case that shares no longer working correctly, the cgroup topology is like: /sys/fs/cgroup/cpu/A (shares=102400) /sys/fs/cgroup/cpu/A/B (shares=2) /sys/fs/cgroup/cpu/A/B/C (shares=1024) /sys/fs/cgroup/cpu/D (shares=1024) /sys/fs/cgroup/cpu/D/E (shares=1024) /sys/fs/cgroup/cpu/D/E/F (shares=1024) The same benchmark is running in group C & F, no other tasks are running, the benchmark is capable to consumed all the CPUs. We suppose the group C will win more CPU resources since it could enjoy all the shares of group A, but it's F who wins much more. The reason is because we have group B with shares as 2, since A->cfs_rq.load.weight == B->se.load.weight == B->shares/nr_cpus, so A->cfs_rq.load.weight become very small. And in calc_group_shares() we calculate shares as: load = max(scale_load_down(cfs_rq->load.weight), cfs_rq->avg.load_avg); shares = (tg_shares * load) / tg_weight; Since the 'cfs_rq->load.weight' is too small, the load become 0 after scale down, although 'tg_shares' is 102400, shares of the se which stand for group A on root cfs_rq become 2. While the se of D on root cfs_rq is far more bigger than 2, so it wins the battle. Thus when scale_load_down() scale real weight down to 0, it's no longer telling the real story, the caller will have the wrong information and the calculation will be buggy. This patch add check in scale_load_down(), so the real weight will be >= MIN_SHARES after scale, after applied the group C wins as expected. Suggested-by:
Michael Wang <yun.wang@linux.alibaba.com> Signed-off-by:
Vincent Guittot <vincent.guittot@linaro.org> Link: https://lkml.kernel.org/r/38e8e212-59a1-64b2-b247-b6d0b52d8dc1@linux.alibaba.comSigned-off-by:
-
Sungbo Eo authored
[ Upstream commit 486562da ] Enclose the chained handler with chained_irq_{enter,exit}(), so that the muxed interrupts get properly acked. This patch also fixes a reboot bug on OX820 SoC, where the jiffies timer interrupt is never acked. The kernel waits a clock tick forever in calibrate_delay_converge(), which leads to a boot hang. Fixes: c41b16f8 ("ARM: integrator/versatile: consolidate FPGA IRQ handling code") Signed-off-by:
-
Alain Volmat authored
[ Upstream commit f491c668 ] Fix a missing struct parameter description to allow warning free W=1 compilation. Signed-off-by:
Alain Volmat <avolmat@me.com> Reviewed-by:
Patrice Chotard <patrice.chotard@st.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Xu Wang authored
[ Upstream commit bcaeb886 ] In qlcnic_83xx_get_reset_instruction_template, the variable of null test is bad, so correct it. Signed-off-by:
Xu Wang <vulab@iscas.ac.cn> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Zheng Wei authored
[ Upstream commit b317538c ] printk in macro vxge_debug_ll uses __VA_ARGS__ without "##" prefix, it causes a build error when there is no variable arguments(e.g. only fmt is specified.). Signed-off-by:
Zheng Wei <wei.zheng@vivo.com> Signed-off-by:
-
Ondrej Jirman authored
[ Upstream commit a43ab30d ] When doing a 16-bit read that returns data in the MSB byte, the RSB_DATA register will keep the MSB byte unchanged when doing the following 8-bit read. sunxi_rsb_read() will then return a result that contains high byte from 16-bit read mixed with the 8-bit result. The consequence is that after this happens the PMIC's regmap will look like this: (0x33 is the high byte from the 16-bit read) % cat /sys/kernel/debug/regmap/sunxi-rsb-3a3/registers 00: 33 01: 33 02: 33 03: 33 04: 33 05: 33 06: 33 07: 33 08: 33 09: 33 0a: 33 0b: 33 0c: 33 0d: 33 0e: 33 [snip] Fix this by masking the result of the read with the correct mask based on the size of the read. There are no 16-bit users in the mainline kernel, so this doesn't need to get into the stable tree. Signed-off-by:
Ondrej Jirman <megous@megous.com> Acked-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Signed-off-by:
-
- 13 Apr, 2020 6 commits
-
-
Greg Kroah-Hartman authored
-
Rob Clark authored
commit 3de433c5 upstream. [subject was: drm/msm: shake fist angrily at dma-mapping] So, using dma_sync_* for our cache needs works out w/ dma iommu ops, but it falls appart with dma direct ops. The problem is that, depending on display generation, we can have either set of dma ops (mdp4 and dpu have iommu wired to mdss node, which maps to toplevel drm device, but mdp5 has iommu wired up to the mdp sub-node within mdss). Fixes this splat on mdp5 devices: Unable to handle kernel paging request at virtual address ffffffff80000000 Mem abort info: ESR = 0x96000144 Exception class = DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 Data abort info: ISV = 0, ISS = 0x00000144 CM = 1, WnR = 1 swapper pgtable: 4k pages, 48-bit VAs, pgdp=00000000810e4000 [ffffffff80000000] pgd=0000000000000000 Internal error: Oops: 96000144 [#1] SMP Modules linked in: btqcomsmd btqca bluetooth cfg80211 ecdh_generic ecc rfkill libarc4 panel_simple msm wcnss_ctrl qrtr_smd drm_kms_helper venus_enc venus_dec videobuf2_dma_sg videobuf2_memops drm venus_core ipv6 qrtr qcom_wcnss_pil v4l2_mem2mem qcom_sysmon videobuf2_v4l2 qmi_helpers videobuf2_common crct10dif_ce mdt_loader qcom_common videodev qcom_glink_smem remoteproc bmc150_accel_i2c bmc150_magn_i2c bmc150_accel_core bmc150_magn snd_soc_lpass_apq8016 snd_soc_msm8916_analog mms114 mc nf_defrag_ipv6 snd_soc_lpass_cpu snd_soc_apq8016_sbc industrialio_triggered_buffer kfifo_buf snd_soc_lpass_platform snd_soc_msm8916_digital drm_panel_orientation_quirks CPU: 2 PID: 33 Comm: kworker/2:1 Not tainted 5.3.0-rc2 #1 Hardware name: Samsung Galaxy A5U (EUR) (DT) Workqueue: events deferred_probe_work_func pstate: 80000005 (Nzcv daif -PAN -UAO) pc : __clean_dcache_area_poc+0x20/0x38 lr : arch_sync_dma_for_device+0x28/0x30 sp : ffff0000115736a0 x29: ffff0000115736a0 x28: 0000000000000001 x27: ffff800074830800 x26: ffff000011478000 x25: 0000000000000000 x24: 0000000000000001 x23: ffff000011478a98 x22: ffff800009fd1c10 x21: 0000000000000001 x20: ffff800075ad0a00 x19: 0000000000000000 x18: ffff0000112b2000 x17: 0000000000000000 x16: 0000000000000000 x15: 00000000fffffff0 x14: ffff000011455d70 x13: 0000000000000000 x12: 0000000000000028 x11: 0000000000000001 x10: ffff00001106c000 x9 : ffff7e0001d6b380 x8 : 0000000000001000 x7 : ffff7e0001d6b380 x6 : ffff7e0001d6b382 x5 : 0000000000000000 x4 : 0000000000001000 x3 : 000000000000003f x2 : 0000000000000040 x1 : ffffffff80001000 x0 : ffffffff80000000 Call trace: __clean_dcache_area_poc+0x20/0x38 dma_direct_sync_sg_for_device+0xb8/0xe8 get_pages+0x22c/0x250 [msm] msm_gem_get_and_pin_iova+0xdc/0x168 [msm] ... Fixes the combination of two patches: Fixes: 0036bc73 (drm/msm: stop abusing dma_map/unmap for cache) Fixes: 449fa54d (dma-direct: correct the physical addr in dma_direct_sync_sg_for_cpu/device) Tested-by:
Stephan Gerhold <stephan@gerhold.net> Signed-off-by:
Rob Clark <robdclark@chromium.org> [seanpaul changed subject to something more desriptive] Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190730214633.17820-1-robdclark@gmail.com Cc: nobuhiro1.iwamatsu@toshiba.co.jp Signed-off-by:
-
Hans Verkuil authored
commit a4c30a48 upstream. When parsing the reply of a DP_REMOTE_DPCD_READ DPCD command the result is wrong due to a missing idx increment. This was never noticed since DP_REMOTE_DPCD_READ is currently not used, but if you enable it, then it is all wrong. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by:
Lyude Paul <lyude@redhat.com> Acked-by:
Alex Deucher <alexander.deucher@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/e72ddac2-1dc0-100a-d816-9ac98ac009dd@xs4all.nlSigned-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Roger Quadros authored
commit c09b73cf upstream. This reverts commit 6a4290cc ("usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.") We don't yet support any of the OTG mechanisms (HNP/SRP/ADP) and are not setting gadget->otg_caps, so don't set gadget->is_otg flag. If we do then we end up publishing a OTG1.0 descriptor in the gadget descriptor which causes device enumeration to fail if we are connected to a host with CONFIG_USB_OTG enabled. Host side log without this patch [ 96.720453] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 96.901391] usb 1-1: Dual-Role OTG device on non-HNP port [ 96.907552] usb 1-1: set a_alt_hnp_support failed: -32 [ 97.060447] usb 1-1: new high-speed USB device number 3 using xhci-hcd [ 97.241378] usb 1-1: Dual-Role OTG device on non-HNP port [ 97.247536] usb 1-1: set a_alt_hnp_support failed: -32 [ 97.253606] usb usb1-port1: attempt power cycle [ 97.960449] usb 1-1: new high-speed USB device number 4 using xhci-hcd [ 98.141383] usb 1-1: Dual-Role OTG device on non-HNP port [ 98.147540] usb 1-1: set a_alt_hnp_support failed: -32 [ 98.300453] usb 1-1: new high-speed USB device number 5 using xhci-hcd [ 98.481391] usb 1-1: Dual-Role OTG device on non-HNP port [ 98.487545] usb 1-1: set a_alt_hnp_support failed: -32 [ 98.493532] usb usb1-port1: unable to enumerate USB device Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Arun KS authored
commit 61cf61d8 upstream. __early_cpu_boot_status is of type long. Use quad assembler directive to allocate proper size. Acked-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Arun KS <arunks@codeaurora.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Rob Clark authored
commit 0036bc73 upstream. Recently splats like this started showing up: WARNING: CPU: 4 PID: 251 at drivers/iommu/dma-iommu.c:451 __iommu_dma_unmap+0xb8/0xc0 Modules linked in: ath10k_snoc ath10k_core fuse msm ath mac80211 uvcvideo cfg80211 videobuf2_vmalloc videobuf2_memops vide CPU: 4 PID: 251 Comm: kworker/u16:4 Tainted: G W 5.2.0-rc5-next-20190619+ #2317 Hardware name: LENOVO 81JL/LNVNB161216, BIOS 9UCN23WW(V1.06) 10/25/2018 Workqueue: msm msm_gem_free_work [msm] pstate: 80c00005 (Nzcv daif +PAN +UAO) pc : __iommu_dma_unmap+0xb8/0xc0 lr : __iommu_dma_unmap+0x54/0xc0 sp : ffff0000119abce0 x29: ffff0000119abce0 x28: 0000000000000000 x27: ffff8001f9946648 x26: ffff8001ec271068 x25: 0000000000000000 x24: ffff8001ea3580a8 x23: ffff8001f95ba010 x22: ffff80018e83ba88 x21: ffff8001e548f000 x20: fffffffffffff000 x19: 0000000000001000 x18: 00000000c00001fe x17: 0000000000000000 x16: 0000000000000000 x15: ffff000015b70068 x14: 0000000000000005 x13: 0003142cc1be1768 x12: 0000000000000001 x11: ffff8001f6de9100 x10: 0000000000000009 x9 : ffff000015b78000 x8 : 0000000000000000 x7 : 0000000000000001 x6 : fffffffffffff000 x5 : 0000000000000fff x4 : ffff00001065dbc8 x3 : 000000000000000d x2 : 0000000000001000 x1 : fffffffffffff000 x0 : 0000000000000000 Call trace: __iommu_dma_unmap+0xb8/0xc0 iommu_dma_unmap_sg+0x98/0xb8 put_pages+0x5c/0xf0 [msm] msm_gem_free_work+0x10c/0x150 [msm] process_one_work+0x1e0/0x330 worker_thread+0x40/0x438 kthread+0x12c/0x130 ret_from_fork+0x10/0x18 ---[ end trace afc0dc5ab81a06bf ]--- Not quite sure what triggered that, but we really shouldn't be abusing dma_{map,unmap}_sg() for cache maint. Cc: Stephen Boyd <sboyd@kernel.org> Tested-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by:
-
