- 03 Dec, 2013 8 commits
-
-
Johannes Berg authored
Add support for vendor-specific commands to nl80211. This is intended to be used for really vendor-specific functionality that can't be implemented in a generic fashion for any reason. It's *NOT* intended to be used for any normal/generic feature or any optimisations that could be implemented across drivers. Currently, only vendor commands (with replies) are supported, no dump operations or vendor-specific notifications. Also add a function wdev_to_ieee80211_vif() to mac80211 which is needed for mac80211-based drivers wanting to implement any vendor commands. Signed-off-by:Johannes Berg <johannes.berg@intel.com>
-
Janusz Dziedzic authored
Don't clear cfg80211_bitrate_mask twice in nl80211_set_tx_bitrate_mask() function. Signed-off-by:
Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by:
-
Eliad Peller authored
The same code appears just a few lines below. Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Luis R. Rodriguez authored
Check the DFS region before channel availability check. Signed-off-by:
Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by:
-
Luis R. Rodriguez authored
This can be used outside of the regulatory context for any checks on the DFS region. The central cfg80211 dfs_region is always used and if it does not match with the wiphy a debug print is issued. Signed-off-by:
-
Marek Kwaczynski authored
This attribute is needed for setting Operating Mode Notification in AP mode from User Space. This functionality is required when User Space received Assoc Request contains Operation Mode Notification element. Signed-off-by:
Marek Kwaczynski <marek.kwaczynski@tieto.com> [fix typos, nl80211 documentation] Signed-off-by:
-
Johannes Berg authored
There's no reason for the variable to not be inside the #ifdef, move it. Signed-off-by: -
Johannes Berg authored
This reverts commit 488b366a. The code isn't used by anyone, and the Intel driver isn't planning to use it either right now. Signed-off-by:
-
- 02 Dec, 2013 13 commits
-
-
Michal Kazior authored
Drivers with hardware rate control were given sta->rx_nss set to 0. This was because rx_nss calculation procedure was protected by hw/sw rate control check. Signed-off-by:
Michal Kazior <michal.kazior@tieto.com> Signed-off-by:
-
Simon Wunderlich authored
Signed-off-by:
Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by:
-
Simon Wunderlich authored
The current channel switch code has a potential deadlock: 1) * cfg80211_stop_ap acquires wdev-lock * ieee80211_stop_ap calls cancel_work_sync for the csa_finalize_work, which acquires the associated worker-lock 2) * ieee80211_csa_finalize_work holds the worker-lock when run * it calls cfg80211_ch_switch_notify which will claim the wdev-lock, and also needs to claim the sdata-lock (which is the same as the wdev-lock) to modify the beacons. It is sufficient to just set the channel switch active to false. If the worker is running later, it will find the channel switch to not be active anymore and returns immediately without changing anything. Canceling the worker is done anyway when the interface goes down (ieee80211_do_stop). Reported-by:Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Simon Wunderlich authored
The channel switch notification should be sent under the wdev/sdata-lock, preferably in the same moment as the channel change happens, to avoid races by other callers (e.g. start/stop_ap). This also adds the previously missing sdata_lock protection in csa_finalize_work. Reported-by:
-
Simon Wunderlich authored
The csa finalize worker needs to change the beacon information (for different modes). These are normally protected under rtnl lock, but the csa finalize worker is called by drivers and should not acquire the RTNL lock. Therefore change access protection for beacons to sdata/wdev lock. Reported-by:
-
Simon Wunderlich authored
To avoid race conditions in functions which modify the beacon information, lock these using the wdev lock. This is especially required to avoid problems for csa handling functions which modify beacons but can not be called under rtnl lock. Reported-by:
-
Bob Copeland authored
The local TSF timer is used to compute the timing offset between mesh peers on beacon reception. However, asking the device for the TSF is not very accurate, so we prefer to use rx->mactime if available. In the latter case, calling drv_get_tsf() just adds more delay into the RX path, so skip it if we can. Signed-off-by:
Bob Copeland <bob@cozybit.com> Signed-off-by:
-
Andrei Otcheretianski authored
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params struct to aggregate parameters for mgmt_tx functions. This makes the functions' signatures less clumsy and allows less painful parameters extension. Signed-off-by:
Andrei Otcheretianski <andrei.otcheretianski@intel.com> [fix all other drivers] Signed-off-by:
-
Avri Altman authored
There's a bug in tracking HT opmode changes in mac80211, it fails to update the driver when the channel parameters don't change. Move the code to do the HT opmode checking independently of the channel/bandwidth tracking. Signed-off-by:
Avri Altman <avri.altman@intel.com> [edit commit message] Signed-off-by:
-
Johannes Berg authored
All interface types now properly clean up their stations using some form of sta_info_flush() themselves, so there's no need to try it again at teardown. Remove the call to get rid of the extra delay from the synchronize_net() and rcu_barrier() calls. Reported-by:
Moshe Benji <moshe.benji@intel.com> Signed-off-by:
-
Matti Gottlieb authored
Measure TX latency and jitter statistics per station per TID. These Measurements are disabled by default and can be enabled via debugfs. Features included for each station's TID: 1. Keep count of the maximum and average latency of Tx frames. 2. Keep track of many frames arrived in a specific time range (need to enable through debugfs and configure the bins ranges) Signed-off-by:
Matti Gottlieb <matti.gottlieb@intel.com> Signed-off-by:
-
Johannes Berg authored
The beacon timers really shouldn't use any clock that is subject to adjustments from userspace, particularly not CLOCK_REALTIME. Use CLOCK_MONOTONIC_RAW instead. Signed-off-by: -
Felix Fietkau authored
nla_put_flag needs a real nl80211 attribute id, not a wiphy flag bit. While at it, split 5 and 10 MHz capability flags in case we ever need to support hardware that can only do one of the two. Also move the flag settings to the split-only information so we don't increase the space needed for old userspace. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> [change location of flag setting] Signed-off-by:
-
- 25 Nov, 2013 19 commits
-
-
Karl Beldan authored
ATM minstrel_ht does not check whether a sampling rate is supported. Unsupported rates attempts can trigger when there are holes in bitfields of supported MCSes belonging to the same group (e.g many devices are MCS32 capable without MCS33->39 capable, also we systematically have a hole for CCK rates). Drop any attempts to sample unsupported rates, as suggested by Felix. This is not a problem in minstrel which fills a per STA sample table with only supported rates (though only at init). Signed-off-by:
Karl Beldan <karl.beldan@rivierawaves.com> Signed-off-by:
-
Luis R. Rodriguez authored
This lets us later reuse the more generic reg_dfs_region_str(). Signed-off-by:
-
Luis R. Rodriguez authored
Signed-off-by:
-
Luis R. Rodriguez authored
Only allow DFS to be set if the DFS regions agree. Signed-off-by:
-
Luis R. Rodriguez authored
u8 was used in some other places, just stick to the enum, this forces us to express the values that are expected. Signed-off-by:
-
Karl Beldan authored
ATM, only the first array value returned by get_random_bytes is used. This change moves the call to get_random_bytes from the nested loop it is in to its parent. While at it, replace get_random_bytes with prandom_bytes since PRNs are way enough for the selection process. After this, minstrel_ht reclaims 80 PR-bytes instead of 640 R-bytes. minstrels use sample tables to probe different rates in a randomized manner. minstrel_ht inits one single sample table upon registration (during subsys_initcalls) and minstrel uses one per STA addition in minstrel. Signed-off-by:
-
Karl Beldan authored
Consecutive MCSes in [8*(NSS-1)->8*NSS[ have the same number NSS of streams (except for MCS32 which is mishandled ATM). ATM minstrel_ht uses MCS_GROUP_RATES in place of this 8 modulus. This change replaces such occurences and by doing so allows for different values of MCS_GROUP_RATES (e.g to cope with VHT MCS8,9). Signed-off-by:
-
Eliad Peller authored
Add a new field to ieee80211_chanctx_conf to indicate the min required channel configuration. Tuning to a narrower channel might help reducing the noise level and saving some power. The min required channel definition is the max of all min required channel definitions of the interfaces bound to this channel context. In AP mode, use 20MHz when there are no connected station. When a new station is added/removed, calculate the new max bandwidth supported by any of the stations (e.g. 80MHz when 80MHz and 40MHz stations are connected). In other cases, simply use bss_conf.chandef as the min required chandef. Notify drivers about changes to this field by calling drv_change_chanctx with a new CHANGE_MIN_WIDTH notification. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Eyal Shapira authored
Introduce shift and mask defines for beamformee STS cap and number of sounding dimensions cap as these can take any 3 bit value. While at it also cleanup an unrequired parenthesis. Signed-off-by:
Eyal Shapira <eyal@wizery.com> Reviewed-by:
-
Luciano Coelho authored
There is no reason why we should have only one channel switch announcement at a time for a single phy. When support for channel switch with multiple contexts and multiple vifs per context is implemented, we will need the chandef data for each vif. Move the csa_chandef structure to sdata to prepare for this. Reviewed-by:
Luciano Coelho <luciano.coelho@intel.com> [Fixed compilation with mesh] Signed-off-by:
-
Chun-Yeow Yeoh authored
Use put_unaligned_le16 and put_unaligned_le32 for mesh_path_error_tx and mesh_path_sel_frame_tx. Signed-off-by:
Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by:
-
Chun-Yeow Yeoh authored
Use put_unaligned_le16 in mesh_plink_frame_tx. Signed-off-by:
-
Luis R. Rodriguez authored
Certain vendors may want to disable the processing of country IEs so that they can continue using the regulatory domain the driver or user has set. Currently there is no way to stop the core from processing country IEs, so add support to the core to ignore country IE hints. Cc: Mihir Shete <smihir@qti.qualcomm.com> Cc: Henri Bahini <hbahini@qca.qualcomm.com> Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com> Signed-off-by:
-
Luis R. Rodriguez authored
802.11 cards may have different country IE parsing behavioural preferences and vendors may want to support these. These preferences were managed by the REGULATORY_CUSTOM_REG and the REGULATORY_STRICT_REG flags and their combination. Instead of using this existing notation, split out the country IE behavioural preferences as a new flag. This will allow us to add more customizations easily and make the code more maintainable. Cc: Mihir Shete <smihir@qti.qualcomm.com> Cc: Henri Bahini <hbahini@qca.qualcomm.com> Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com> Signed-off-by:
-
Luis R. Rodriguez authored
We'll expand this later, this will make it easier to classify and review what things are related to regulatory or not. Coccinelle only missed 4 hits, which I had to do manually, supplying the SmPL in case of merge conflicts. @@ struct wiphy *wiphy; @@ -wiphy->flags |= WIPHY_FLAG_CUSTOM_REGULATORY +wiphy->regulatory_flags |= REGULATORY_CUSTOM_REG @@ expression e; @@ -e->flags |= WIPHY_FLAG_CUSTOM_REGULATORY +e->regulatory_flags |= REGULATORY_CUSTOM_REG @@ struct wiphy *wiphy; @@ -wiphy->flags &= ~WIPHY_FLAG_CUSTOM_REGULATORY +wiphy->regulatory_flags &= ~REGULATORY_CUSTOM_REG @@ struct wiphy *wiphy; @@ -wiphy->flags & WIPHY_FLAG_CUSTOM_REGULATORY +wiphy->regulatory_flags & REGULATORY_CUSTOM_REG @@ struct wiphy *wiphy; @@ -wiphy->flags |= WIPHY_FLAG_STRICT_REGULATORY +wiphy->regulatory_flags |= REGULATORY_STRICT_REG @@ expression e; @@ -e->flags |= WIPHY_FLAG_STRICT_REGULATORY +e->regulatory_flags |= REGULATORY_STRICT_REG @@ struct wiphy *wiphy; @@ -wiphy->flags &= ~WIPHY_FLAG_STRICT_REGULATORY +wiphy->regulatory_flags &= ~REGULATORY_STRICT_REG @@ struct wiphy *wiphy; @@ -wiphy->flags & WIPHY_FLAG_STRICT_REGULATORY +wiphy->regulatory_flags & REGULATORY_STRICT_REG @@ struct wiphy *wiphy; @@ -wiphy->flags |= WIPHY_FLAG_DISABLE_BEACON_HINTS +wiphy->regulatory_flags |= REGULATORY_DISABLE_BEACON_HINTS @@ expression e; @@ -e->flags |= WIPHY_FLAG_DISABLE_BEACON_HINTS +e->regulatory_flags |= REGULATORY_DISABLE_BEACON_HINTS @@ struct wiphy *wiphy; @@ -wiphy->flags &= ~WIPHY_FLAG_DISABLE_BEACON_HINTS +wiphy->regulatory_flags &= ~REGULATORY_DISABLE_BEACON_HINTS @@ struct wiphy *wiphy; @@ -wiphy->flags & WIPHY_FLAG_DISABLE_BEACON_HINTS +wiphy->regulatory_flags & REGULATORY_DISABLE_BEACON_HINTS Generated-by: Coccinelle SmPL Cc: Julia Lawall <julia.lawall@lip6.fr> Cc: Peter Senna Tschudin <peter.senna@gmail.com> Cc: Mihir Shete <smihir@qti.qualcomm.com> Cc: Henri Bahini <hbahini@qca.qualcomm.com> Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com> Signed-off-by:
-
Chun-Yeow Yeoh authored
use put_unaligned_le16 for precedence value in mesh channel switch support Signed-off-by:
-
Karl Beldan authored
Signed-off-by:
-
Luis R. Rodriguez authored
This reflects that case is now completely separated. Signed-off-by:
-
Luis R. Rodriguez authored
This splits up the driver regulatory update on its own, this helps simplify the reading the case. Signed-off-by:
-
