- 05 Mar, 2024 20 commits
-
-
Arınç ÜNAL authored
Remove error returns on the cases where they are already handled with the function the mac_port_get_caps member in mt753x_table points to. mt7531_mac_config() is also called from mt7531_cpu_port_config() outside of phylink but the port and interface modes are already handled there. Change the functions and the mac_port_config function pointer to void now that there're no error returns anymore. Remove mt753x_is_mac_port() that used to help the said error returns. On mt7531_mac_config(), switch to if statements to simplify the code. Remove internal phy cases from mt753x_phylink_mac_config(), there is no need to check the interface mode as that's already handled with the function the mac_port_get_caps member in mt753x_table points to. Acked-by:
Daniel Golle <daniel@makrotopia.org> Tested-by:
Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Arınç ÜNAL authored
According to the document MT7531 Reference Manual for Development Board v1.0, the SW_PHY_RST bit on the SYS_CTRL register doesn't exist for MT7531. This is likely why forcing link down on all ports is necessary for MT7531. Therefore, do not set SW_PHY_RST on mt7531_setup(). Signed-off-by:
-
Arınç ÜNAL authored
Setting this register related to interrupts is only needed for the MT7530 switch. Make an exclusive check to ensure this. Signed-off-by:
-
Arınç ÜNAL authored
For the switch on the MT7988 SoC, the mac_port_config member for ID_MT7988 in mt753x_table is not needed as the interfaces of all MACs are already handled on mt7988_mac_port_get_caps(). Therefore, remove the mac_port_config member from ID_MT7988 in mt753x_table. Before calling priv->info->mac_port_config(), if there's no mac_port_config member in mt753x_table, exit mt753x_mac_config() successfully. Remove calling priv->info->mac_port_config() from the sanity check as the sanity check requires a pointer to a mac_port_config function to be non-NULL. This will fail for MT7988 as mac_port_config won't be a member of its info table. Co-developed-by:
Vladimir Oltean <olteanv@gmail.com> Reviewed-by:
-
Paolo Abeni authored
Yunsheng Lin says: ==================== remove page frag implementation in vhost_net Currently there are three implementations for page frag: 1. mm/page_alloc.c: net stack seems to be using it in the rx part with 'struct page_frag_cache' and the main API being page_frag_alloc_align(). 2. net/core/sock.c: net stack seems to be using it in the tx part with 'struct page_frag' and the main API being skb_page_frag_refill(). 3. drivers/vhost/net.c: vhost seems to be using it to build xdp frame, and it's implementation seems to be a mix of the above two. This patchset tries to unfiy the page frag implementation a little bit by unifying gfp bit for order 3 page allocation and replacing page frag implementation in vhost.c with the one in page_alloc.c. After this patchset, we are not only able to unify the page frag implementation a little, but also able to have about 0.5% performance boost testing by using the vhost_net_test introduced in the last patch. Before this patchset: Performance counter stats for './vhost_net_test' (10 runs): 305325.78 msec task-clock # 1.738 CPUs utilized ( +- 0.12% ) 1048668 context-switches # 3.435 K/sec ( +- 0.00% ) 11 cpu-migrations # 0.036 /sec ( +- 17.64% ) 33 page-faults # 0.108 /sec ( +- 0.49% ) 244651819491 cycles # 0.801 GHz ( +- 0.43% ) (64) 64714638024 stalled-cycles-frontend # 26.45% frontend cycles idle ( +- 2.19% ) (67) 30774313491 stalled-cycles-backend # 12.58% backend cycles idle ( +- 7.68% ) (70) 201749748680 instructions # 0.82 insn per cycle # 0.32 stalled cycles per insn ( +- 0.41% ) (66.76%) 65494787909 branches # 214.508 M/sec ( +- 0.35% ) (64) 4284111313 branch-misses # 6.54% of all branches ( +- 0.45% ) (66) 175.699 +- 0.189 seconds time elapsed ( +- 0.11% ) After this patchset: Performance counter stats for './vhost_net_test' (10 runs): 303974.38 msec task-clock # 1.739 CPUs utilized ( +- 0.14% ) 1048807 context-switches # 3.450 K/sec ( +- 0.00% ) 14 cpu-migrations # 0.046 /sec ( +- 12.86% ) 33 page-faults # 0.109 /sec ( +- 0.46% ) 251289376347 cycles # 0.827 GHz ( +- 0.32% ) (60) 67885175415 stalled-cycles-frontend # 27.01% frontend cycles idle ( +- 0.48% ) (63) 27809282600 stalled-cycles-backend # 11.07% backend cycles idle ( +- 0.36% ) (71) 195543234672 instructions # 0.78 insn per cycle # 0.35 stalled cycles per insn ( +- 0.29% ) (69.04%) 62423183552 branches # 205.357 M/sec ( +- 0.48% ) (67) 4135666632 branch-misses # 6.63% of all branches ( +- 0.63% ) (67) 174.764 +- 0.214 seconds time elapsed ( +- 0.12% ) Changelog: V6: Add timeout for poll() and simplify some logic as suggested by Jason. V5: Address the comment from jason in vhost_net_test.c and the comment about leaving out the gfp change for page frag in sock.c as suggested by Paolo. V4: Resend based on latest net-next branch. V3: 1. Add __page_frag_alloc_align() which is passed with the align mask the original function expected as suggested by Alexander. 2. Drop patch 3 in v2 suggested by Alexander. 3. Reorder patch 4 & 5 in v2 suggested by Alexander. Note that placing this gfp flags handing for order 3 page in an inline function is not considered, as we may be able to unify the page_frag and page_frag_cache handling. V2: Change 'xor'd' to 'masked off', add vhost tx testing for vhost_net_test. V1: Fix some typo, drop RFC tag and rebase on latest net-next. ==================== Link: https://lore.kernel.org/r/20240228093013.8263-1-linyunsheng@huawei.comSigned-off-by: -
Yunsheng Lin authored
introduce vhost_net_test for both vhost_net tx and rx basing on virtio_test to test vhost_net changing in the kernel. Steps for vhost_net tx testing: 1. Prepare a out buf. 2. Kick the vhost_net to do tx processing. 3. Do the receiving in the tun side. 4. verify the data received by tun is correct. Steps for vhost_net rx testing: 1. Prepare a in buf. 2. Do the sending in the tun side. 3. Kick the vhost_net to do rx processing. 4. verify the data received by vhost_net is correct. Signed-off-by:
Yunsheng Lin <linyunsheng@huawei.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Yunsheng Lin authored
The page frag in vhost_net_page_frag_refill() uses the 'struct page_frag' from skb_page_frag_refill(), but it's implementation is similar to page_frag_alloc_align() now. This patch removes vhost_net_page_frag_refill() by using 'struct page_frag_cache' instead of 'struct page_frag', and allocating frag using page_frag_alloc_align(). The added benefit is that not only unifying the page frag implementation a little, but also having about 0.5% performance boost testing by using the vhost_net_test introduced in the last patch. Signed-off-by:
Jason Wang <jasowang@redhat.com> Acked-by:
-
Yunsheng Lin authored
When draining a page_frag_cache, most user are doing the similar steps, so introduce an API to avoid code duplication. Signed-off-by:
Alexander Duyck <alexanderduyck@fb.com> Acked-by:
-
Yunsheng Lin authored
Currently there seems to be three page frag implementations which all try to allocate order 3 page, if that fails, it then fail back to allocate order 0 page, and each of them all allow order 3 page allocation to fail under certain condition by using specific gfp bits. The gfp bits for order 3 page allocation are different between different implementation, __GFP_NOMEMALLOC is or'd to forbid access to emergency reserves memory for __page_frag_cache_refill(), but it is not or'd in other implementions, __GFP_DIRECT_RECLAIM is masked off to avoid direct reclaim in vhost_net_page_frag_refill(), but it is not masked off in __page_frag_cache_refill(). This patch unifies the gfp bits used between different implementions by or'ing __GFP_NOMEMALLOC and masking off __GFP_DIRECT_RECLAIM for order 3 page allocation to avoid possible pressure for mm. Leave the gfp unifying for page frag implementation in sock.c for now as suggested by Paolo Abeni. Signed-off-by:
-
Yunsheng Lin authored
napi_alloc_frag_align() and netdev_alloc_frag_align() accept align as an argument, and they are thin wrappers around the __napi_alloc_frag_align() and __netdev_alloc_frag_align() APIs doing the alignment checking and align mask conversion, in order to call page_frag_alloc_align() directly. The intention here is to keep the alignment checking and the alignmask conversion in in-line wrapper to avoid those kind of operations during execution time since it can usually be handled during compile time. We are going to use page_frag_alloc_align() in vhost_net.c, it need the same kind of alignment checking and alignmask conversion, so split up page_frag_alloc_align into an inline wrapper doing the above operation, and add __page_frag_alloc_align() which is passed with the align mask the original function expected as suggested by Alexander. Signed-off-by:
-
Jiawen Wu authored
GPIO EOI is not set to clear interrupt status after handling the interrupt. It should be done in irq_chip->irq_ack, but this function is not called in handle_nested_irq(). So executing function txgbe_gpio_irq_ack() manually in txgbe_gpio_irq_handler(). Fixes: aefd0136 ("net: txgbe: use irq_domain for interrupt controller") Signed-off-by:
Jiawen Wu <jiawenwu@trustnetic.com> Link: https://lore.kernel.org/r/20240301092956.18544-2-jiawenwu@trustnetic.comSigned-off-by:
-
Jiawen Wu authored
The register of GPIO interrupt status is masked before MAC IRQ is enabled. This is because of hardware deficiency. So manually clear the interrupt status before using them. Otherwise, GPIO interrupts will never be reported again. There is a workaround for clearing interrupts to set GPIO EOI in txgbe_up_complete(). Fixes: aefd0136 ("net: txgbe: use irq_domain for interrupt controller") Signed-off-by:
-
Jakub Kicinski authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-02-28 (ixgbe, igc, igb, e1000e, e100) This series contains updates to ixgbe, igc, igb, e1000e, and e100 drivers. Jon Maxwell makes module parameter values readable in sysfs for ixgbe, igb, and e100. Ernesto Castellotti adds support for 1000BASE-BX on ixgbe. Arnd Bergmann fixes build failure due to dependency issues for igc. Vitaly refactors error check to be more concise and prevent future issues on e1000e. v1: https://lore.kernel.org/netdev/20240229004135.741586-1-anthony.l.nguyen@intel.com/ ==================== Link: https://lore.kernel.org/r/20240301184806.2634508-1-anthony.l.nguyen@intel.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Vitaly Lifshits authored
Add curly braces to avoid entering to an if statement where it is not always required in e1000_shutdown function. This improves code readability and might prevent non-deterministic behaviour in the future. Signed-off-by:
Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by:
Naama Meir <naamax.meir@linux.intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20240301184806.2634508-5-anthony.l.nguyen@intel.comSigned-off-by:
-
Arnd Bergmann authored
When IGC is built-in but LEDS_CLASS is a loadable module, there is a link failure: x86_64-linux-ld: drivers/net/ethernet/intel/igc/igc_leds.o: in function `igc_led_setup': igc_leds.c:(.text+0x75c): undefined reference to `devm_led_classdev_register_ext' Add another dependency that prevents this combination. Fixes: ea578703 ("igc: Add support for LEDs on i225/i226") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by:
-
Ernesto Castellotti authored
Added support for 1000BASE-BX, i.e. Gigabit Ethernet over single strand of single-mode fiber. The initialization of a 1000BASE-BX SFP is the same as 1000BASE-SX/LX with the only difference that the Bit Rate Nominal Value must be checked to make sure it is a Gigabit Ethernet transceiver, as described by the SFF-8472 specification. This was tested with the FS.com SFP-GE-BX 1310/1490nm 10km transceiver: $ ethtool -m eth4 Identifier : 0x03 (SFP) Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID) Connector : 0x07 (LC) Transceiver codes : 0x00 0x00 0x00 0x40 0x00 0x00 0x00 0x00 0x00 Transceiver type : Ethernet: BASE-BX10 Encoding : 0x01 (8B/10B) BR, Nominal : 1300MBd Rate identifier : 0x00 (unspecified) Length (SMF,km) : 10km Length (SMF) : 10000m Length (50um) : 0m Length (62.5um) : 0m Length (Copper) : 0m Length (OM3) : 0m Laser wavelength : 1310nm Vendor name : FS Vendor OUI : 64:9d:99 Vendor PN : SFP-GE-BX Vendor rev : Option values : 0x20 0x0a Option : RX_LOS implemented Option : TX_FAULT implemented Option : Power level 3 requirement BR margin, max : 0% BR margin, min : 0% Vendor SN : S2202359108 Date code : 220307 Optical diagnostics support : Yes Laser bias current : 17.650 mA Laser output power : 0.2132 mW / -6.71 dBm Receiver signal average optical power : 0.2740 mW / -5.62 dBm Module temperature : 47.30 degrees C / 117.13 degrees F Module voltage : 3.2576 V Alarm/warning flags implemented : Yes Laser bias current high alarm : Off Laser bias current low alarm : Off Laser bias current high warning : Off Laser bias current low warning : Off Laser output power high alarm : Off Laser output power low alarm : Off Laser output power high warning : Off Laser output power low warning : Off Module temperature high alarm : Off Module temperature low alarm : Off Module temperature high warning : Off Module temperature low warning : Off Module voltage high alarm : Off Module voltage low alarm : Off Module voltage high warning : Off Module voltage low warning : Off Laser rx power high alarm : Off Laser rx power low alarm : Off Laser rx power high warning : Off Laser rx power low warning : Off Laser bias current high alarm threshold : 110.000 mA Laser bias current low alarm threshold : 1.000 mA Laser bias current high warning threshold : 100.000 mA Laser bias current low warning threshold : 1.000 mA Laser output power high alarm threshold : 0.7079 mW / -1.50 dBm Laser output power low alarm threshold : 0.0891 mW / -10.50 dBm Laser output power high warning threshold : 0.6310 mW / -2.00 dBm Laser output power low warning threshold : 0.1000 mW / -10.00 dBm Module temperature high alarm threshold : 90.00 degrees C / 194.00 degrees F Module temperature low alarm threshold : -45.00 degrees C / -49.00 degrees F Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F Module temperature low warning threshold : -40.00 degrees C / -40.00 degrees F Module voltage high alarm threshold : 3.7950 V Module voltage low alarm threshold : 2.8050 V Module voltage high warning threshold : 3.4650 V Module voltage low warning threshold : 3.1350 V Laser rx power high alarm threshold : 0.7079 mW / -1.50 dBm Laser rx power low alarm threshold : 0.0028 mW / -25.53 dBm Laser rx power high warning threshold : 0.6310 mW / -2.00 dBm Laser rx power low warning threshold : 0.0032 mW / -24.95 dBm Signed-off-by:Ernesto Castellotti <ernesto@castellotti.net> Reviewed-by:
Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel) Signed-off-by:
-
Jon Maxwell authored
Linux users sometimes need an easy way to check current values of module parameters. For example the module may be manually reloaded with different parameters. Make these visible and readable in the /sys filesystem to allow that. But don't make the "debug" module parameter visible as debugging is enabled via ethtool msglvl. Signed-off-by:
Jon Maxwell <jmaxwell37@gmail.com> Reviewed-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by:
-
Eric Dumazet authored
Stephen Rothwell and kernel test robot reported that some arches (parisc, hexagon) and/or compilers would not like blamed commit. Lets make sure tcp_sock_write_rx group does not start with a hole. While we are at it, correct tcp_sock_write_tx CACHELINE_ASSERT_GROUP_SIZE() since after the blamed commit, we went to 105 bytes. Fixes: 99123622 ("tcp: remove some holes in struct tcp_sock") Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Reported-by:
kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/netdev/20240301121108.5d39e4f9@canb.auug.org.au/ Closes: https://lore.kernel.org/oe-kbuild-all/202403011451.csPYOS3C-lkp@intel.com/Signed-off-by:
Eric Dumazet <edumazet@google.com> Reviewed-by:
Simon Horman <horms@kernel.org> Tested-by: Simon Horman <horms@kernel.org> # build-tested Link: https://lore.kernel.org/r/20240301171945.2958176-1-edumazet@google.comSigned-off-by:
-
Pedro Tammela authored
Add the dependsOn test check for all the mirred blockcast tests. It will prevent the issue reported by LKFT which happens when an older iproute2 is used to run the current tdc. Tests are skipped if the dependsOn check fails. Reported-by:
Linux Kernel Functional Testing <lkft@linaro.org> Signed-off-by:
Pedro Tammela <pctammela@mojatatu.com> Link: https://lore.kernel.org/r/20240229143825.1373550-1-pctammela@mojatatu.comSigned-off-by:
-
Prabhav Kumar Vaish authored
Changes : - "excercise" is corrected to "exercise" in drivers/net/mlxsw/spectrum-2/tc_flower.sh - "mutliple" is corrected to "multiple" in drivers/net/netdevsim/ethtool-fec.sh Signed-off-by:
Prabhav Kumar Vaish <pvkumar5749404@gmail.com> Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/20240228120701.422264-1-pvkumar5749404@gmail.comSigned-off-by:
-
- 04 Mar, 2024 20 commits
-
-
David S. Miller authored
Matthieu Baerts says: ==================== mptcp: userspace pm: 'dump addrs' and 'get addr' This series from Geliang adds two new Netlink commands to the userspace PM: - one to dump all addresses of a specific MPTCP connection: - feature added in patches 3 to 5 - test added in patches 7, 8 and 10 - and one to get a specific address for an MPTCP connection: - feature added in patches 11 to 13 - test added in patches 14 and 15 These new Netlink commands can be useful if an MPTCP daemon lost track of the different connections, e.g. after having been restarted. The other patches are some clean-ups and small improvements added while working on the new features. ==================== Signed-off-by:Matthieu Baerts (NGI0) <matttbe@kernel.org>
-
Geliang Tang authored
This patch adds a new helper userspace_pm_get_addr() in mptcp_join.sh. In it, parse the token value from the output of 'pm_nl_ctl events', then pass it to pm_nl_ctl get_addr command. Use this helper in userspace pm dump tests. Signed-off-by:
Geliang Tang <tanggeliang@kylinos.cn> Reviewed-by:
Mat Martineau <martineau@kernel.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Geliang Tang authored
The command get_addr() of pm_nl_ctl can be used like this in in-kernel PM: pm_nl_ctl get $id This patch adds token argument for it to support userspace PM: pm_nl_ctl get $id token $token If 'token $token' is passed to get_addr(), copy it into the kernel netlink. Signed-off-by:
-
Geliang Tang authored
This patch renames mptcp_pm_nl_get_addr_doit() as a dedicated in-kernel netlink PM get addr function mptcp_pm_nl_get_addr(). and invoke a new wrapper mptcp_pm_get_addr() in mptcp_pm_nl_get_addr_doit. If a token is gotten in the wrapper, that means a userspace PM is used. So invoke mptcp_userspace_pm_get_addr() to get addr in userspace PM list. Otherwise, invoke mptcp_pm_nl_get_addr(). Signed-off-by:
-
Geliang Tang authored
This patch implements mptcp_userspace_pm_get_addr() to get an address from userspace pm address list according the given 'token' and 'id'. Use nla_get_u32() to get the u32 value of 'token', then pass it to mptcp_token_get_sock() to get the msk. Pass 'msk' and 'id' to the helper mptcp_userspace_pm_lookup_addr_by_id() to get the address entry. Put this entry to userspace using mptcp_pm_nl_put_entry_info(). Signed-off-by:
-
Geliang Tang authored
Corresponding __lookup_addr_by_id() helper in the in-kernel netlink PM, this patch adds a new helper mptcp_userspace_pm_lookup_addr_by_id() to lookup the address entry with the given id on the userspace pm local address list. Signed-off-by:
-
Geliang Tang authored
This patch adds a new helper userspace_pm_dump() to dump addresses for the userspace PM. Use this helper to check whether an ID 0 subflow is listed in the output of dump command after creating an ID 0 subflow in "userspace pm create id 0 subflow" test. Dump userspace PM addresses list in "userspace pm add & remove address" test and in "userspace pm create destroy subflow" test. Signed-off-by:
-
Geliang Tang authored
Extract the main part of check() in pm_netlink.sh into a new helper named mptcp_lib_check_output in mptcp_lib.sh. This helper will be used for userspace dump addresses tests. Co-developed-by:
-
Geliang Tang authored
The command dump_addr() of pm_nl_ctl can be used like this in in-kernel PM: pm_nl_ctl dump This patch adds token argument for it to support userspace PM: pm_nl_ctl dump token $token If 'token $token' is passed to dump_addr(), copy it into the kernel netlink. Signed-off-by: -
Geliang Tang authored
This patch adds the address flag MPTCP_PM_ADDR_FLAG_SUBFLOW in csf() in pm_nl_ctl.c when subflow is created by a userspace PM. Signed-off-by:
-
Geliang Tang authored
Just like MPTCP_PM_ADDR_FLAG_SIGNAL flag is checked in userspace PM announce mptcp_pm_nl_announce_doit(), PM flags should be checked in mptcp_pm_nl_subflow_create_doit() too. If MPTCP_PM_ADDR_FLAG_SUBFLOW flag is not set, there's no flags field in the output of dump_addr. This looks a bit strange: id 10 flags 10.0.3.2 This patch uses mptcp_pm_parse_entry() instead of mptcp_pm_parse_addr() to get the PM flags of the entry and check it. MPTCP_PM_ADDR_FLAG_SIGNAL flag shouldn't be set here, and if MPTCP_PM_ADDR_FLAG_SUBFLOW flag is missing from the netlink attribute, always set this flag. Signed-off-by: -
Geliang Tang authored
This patch renames mptcp_pm_nl_get_addr_dumpit() as a dedicated in-kernel netlink PM dump addrs function mptcp_pm_nl_dump_addr(), and invoke a newly added wrapper mptcp_pm_dump_addr() in mptcp_pm_nl_get_addr_dumpit(). Invoke in-kernel PM dump addrs function mptcp_pm_nl_dump_addr() or userspace PM dump addrs function mptcp_userspace_pm_dump_addr() based on whether the token parameter is passed in or not in the wrapper. Signed-off-by:
-
Geliang Tang authored
This patch adds token parameter together with addr in get-addr section in mptcp_pm.yaml, then use the following commands to update mptcp_pm_gen.c and mptcp_pm_gen.h: ./tools/net/ynl/ynl-gen-c.py --mode kernel \ --spec Documentation/netlink/specs/mptcp_pm.yaml --source \ -o net/mptcp/mptcp_pm_gen.c ./tools/net/ynl/ynl-gen-c.py --mode kernel \ --spec Documentation/netlink/specs/mptcp_pm.yaml --header \ -o net/mptcp/mptcp_pm_gen.h Signed-off-by: -
Geliang Tang authored
This patch implements mptcp_userspace_pm_dump_addr() to dump addresses from userspace pm address list. Use mptcp_token_get_sock() to get the msk from the given token, if userspace PM is enabled in it, traverse each address entry in address list, put every entry to userspace using mptcp_pm_nl_put_entry_msg(). Signed-off-by:
-
Geliang Tang authored
This patch exports struct mptcp_genl_family and mptcp_nl_fill_addr() helper to allow them can be used in pm_userspace.c. Signed-off-by:
-
Geliang Tang authored
mptcp_pm_remove_addrs_and_subflows() is only used in pm_netlink.c, it's no longer used in pm_userspace.c any more since the commit 8b1c94da ("mptcp: only send RM_ADDR in nl_cmd_remove"). So this patch changes it to a static function. Signed-off-by:
-
David S. Miller authored
Alex Elder says: ==================== net: ipa: simplify device pointer access This version of this patch series fixes the bugs in the first patch (which were fixed in the second), where ipa_interrupt_config() had two remaining spots that returned a pointer rather than an integer. Outside of initialization, all uses of the platform device pointer stored in the IPA structure determine the address of device structure embedded within the platform device structure. By changing some of the initialization functions to take a platform device as argument we can simplify getting at the device structure address by storing it (instead of the platform device pointer) in the IPA structure. The first two patches split the interrupt initialization code into two parts--one done earlier than before. The next four patches update some initialization functions to take a platform device pointer as argument. And the last patch replaces the platform device pointer with a device pointer, and converts all remaining references to the &ipa->pdev->dev to use ipa->dev. ==================== Signed-off-by: -
Alex Elder authored
The IPA platform device is now only used as the structure containing the IPA device structure. Replace the platform device pointer with a pointer to the device structure. Signed-off-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Alex Elder authored
Rather than using the platform device pointer field in the IPA pointer, pass a platform device pointer to ipa_smp2p_init(). Use that pointer throughout that function. Signed-off-by:
-
Alex Elder authored
Rather than using the platform device pointer field in the IPA pointer, pass a platform device pointer to ipa_smp2p_irq_init(). Use that pointer throughout that function (without assuming it's the same as the IPA platform device pointer). Signed-off-by:
-
