- 27 Apr, 2019 39 commits
-
-
Mike Looijmans authored
commit 73f3bc6d upstream. The SPI interface implementation was completely broken. When using the SPI interface, there are only 7 address bits, the upper bit is controlled by a page select register. The core needs access to both ranges, so implement register read/write for both regions. The regmap paging functionality didn't agree with a register that needs to be read and modified, so I implemented a custom paging algorithm. This fixes that the device wouldn't even probe in SPI mode. The SPI interface then isn't different from I2C, merged them into the core, and the I2C/SPI named registers are no longer needed. Implemented register value caching for the registers to reduce the I2C/SPI data transfers considerably. The calibration set reads as all zeroes until some undefined point in time, and I couldn't determine what makes it valid. The datasheet mentions these registers but does not provide any hints on when they become valid, and they aren't even enumerated in the memory map. So check the calibration and retry reading it from the device after each measurement until it provides something valid. Despite the size this is suitable for a stable backport given that it seems the SPI support never worked. Signed-off-by:
Mike Looijmans <mike.looijmans@topic.nl> Fixes: 1b3bd859 ("iio: chemical: Add support for Bosch BME680 sensor"); Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mike Looijmans authored
commit 9436f45d upstream. The standard unit for temperature is millidegrees Celcius. Adapt the driver to report in millidegrees instead of degrees. Signed-off-by:
-
Mike Looijmans authored
commit 40a7198a upstream. Standard unit for temperature is millidegrees Celcius, whereas this driver was reporting in degrees. Fix the scale factor in the driver. Signed-off-by:
-
Sergey Larin authored
commit 409a51e0 upstream. According to the datasheet, the last bit of CHIP_ID register controls I2C bus, and the first one is unused. Handle this correctly. Note that there are chips out there that have a value such that the id check currently fails. Signed-off-by:
Sergey Larin <cerg2010cerg2010@mail.ru> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Mircea Caprioru authored
commit 7ce0f216 upstream. This patch fixes the differential channels addresses for the ad7193. Signed-off-by:
Mircea Caprioru <mircea.caprioru@analog.com> Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Leonard Pollak authored
commit 0a8a29be upstream. This patch fixes an obvious typo, which will cause erroneously returning the Peak Voltage instead of the Peak Current. Signed-off-by:
Leonard Pollak <leonardp@tr-host.de> Cc: <Stable@vger.kernel.org> Acked-by:
Michael Hennerich <michael.hennerich@analog.com> Signed-off-by:
-
Vitaly Kuznetsov authored
commit 99c22179 upstream. I noticed that apic test from kvm-unit-tests always hangs on my EPYC 7401P, the hanging test nmi-after-sti is trying to deliver 30000 NMIs and tracing shows that we're sometimes able to deliver a few but never all. When we're trying to inject an NMI we may fail to do so immediately for various reasons, however, we still need to inject it so enable_nmi_window() arms nmi_singlestep mode. #DB occurs as expected, but we're not checking for pending NMIs before entering the guest and unless there's a different event to process, the NMI will never get delivered. Make KVM_REQ_EVENT request on the vCPU from db_interception() to make sure pending NMIs are checked and possibly injected. Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Cc: stable@vger.kernel.org Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Sean Christopherson authored
commit 8f4dc2e7 upstream. Neither AMD nor Intel CPUs have an EFER field in the legacy SMRAM save state area, i.e. don't save/restore EFER across SMM transitions. KVM somewhat models this, e.g. doesn't clear EFER on entry to SMM if the guest doesn't support long mode. But during RSM, KVM unconditionally clears EFER so that it can get back to pure 32-bit mode in order to start loading CRs with their actual non-SMM values. Clear EFER only when it will be written when loading the non-SMM state so as to preserve bits that can theoretically be set on 32-bit vCPUs, e.g. KVM always emulates EFER_SCE. And because CR4.PAE is cleared only to play nice with EFER, wrap that code in the long mode check as well. Note, this may result in a compiler warning about cr4 being consumed uninitialized. Re-read CR4 even though it's technically unnecessary, as doing so allows for more readable code and RSM emulation is not a performance critical path. Fixes: 660a5d51 ("KVM: x86: save/load state on SMM switch") Cc: stable@vger.kernel.org Signed-off-by:
Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by:
-
Ronnie Sahlberg authored
commit e6d0fb7b upstream. If we enter smb2_query_symlink() for something that is not a symlink and where the SMB2_open() would succeed we would never end up closing this handle and would thus leak a handle on the server. Fix this by immediately calling SMB2_close() on successfull open. Signed-off-by:
Ronnie Sahlberg <lsahlber@redhat.com> CC: Stable <stable@vger.kernel.org> Signed-off-by:
Steve French <stfrench@microsoft.com> Reviewed-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
-
ZhangXiaoxu authored
commit 088aaf17 upstream. There is a KASAN use-after-free: BUG: KASAN: use-after-free in SMB2_read+0x1136/0x1190 Read of size 8 at addr ffff8880b4e45e50 by task ln/1009 Should not release the 'req' because it will use in the trace. Fixes: eccb4422 ("smb3: Add ftrace tracepoints for improved SMB3 debugging") Signed-off-by:
ZhangXiaoxu <zhangxiaoxu5@huawei.com> Signed-off-by:
-
ZhangXiaoxu authored
commit 6a3eb336 upstream. There is a KASAN use-after-free: BUG: KASAN: use-after-free in SMB2_write+0x1342/0x1580 Read of size 8 at addr ffff8880b6a8e450 by task ln/4196 Should not release the 'req' because it will use in the trace. Fixes: eccb4422 ("smb3: Add ftrace tracepoints for improved SMB3 debugging") Signed-off-by:
-
Aurelien Aptel authored
commit b98749ca upstream. In the oplock break handler, writing pending changes from pages puts the FileInfo handle. If the refcount reaches zero it closes the handle and waits for any oplock break handler to return, thus causing a deadlock. To prevent this situation: * We add a wait flag to cifsFileInfo_put() to decide whether we should wait for running/pending oplock break handlers * We keep an additionnal reference of the SMB FileInfo handle so that for the rest of the handler putting the handle won't close it. - The ref is bumped everytime we queue the handler via the cifs_queue_oplock_break() helper. - The ref is decremented at the end of the handler This bug was triggered by xfstest 464. Also important fix to address the various reports of oops in smb2_push_mandatory_locks Signed-off-by:
Aurelien Aptel <aaptel@suse.com> Signed-off-by:
-
Peter Oskolkov authored
[ Upstream commit 997dd964 ] Currently, IPv6 defragmentation code drops non-last fragments that are smaller than 1280 bytes: see commit 0ed4229b ("ipv6: defrag: drop non-last frags smaller than min mtu") This behavior is not specified in IPv6 RFCs and appears to break compatibility with some IPv6 implemenations, as reported here: https://www.spinics.net/lists/netdev/msg543846.html This patch re-uses common IP defragmentation queueing and reassembly code in IP6 defragmentation in nf_conntrack, removing the 1280 byte restriction. Signed-off-by:
Peter Oskolkov <posk@google.com> Reported-by:
Tom Herbert <tom@herbertland.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Florian Westphal <fw@strlen.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Peter Oskolkov authored
[ Upstream commit d4289fcc ] Currently, IPv6 defragmentation code drops non-last fragments that are smaller than 1280 bytes: see commit 0ed4229b ("ipv6: defrag: drop non-last frags smaller than min mtu") This behavior is not specified in IPv6 RFCs and appears to break compatibility with some IPv6 implemenations, as reported here: https://www.spinics.net/lists/netdev/msg543846.html This patch re-uses common IP defragmentation queueing and reassembly code in IPv6, removing the 1280 byte restriction. v2: change handling of overlaps to match that of upstream. Signed-off-by:
-
Peter Oskolkov authored
[ Upstream commit c23f35d1 ] This is a refactoring patch: without changing runtime behavior, it moves rbtree-related code from IPv4-specific files/functions into .h/.c defrag files shared with IPv6 defragmentation code. v2: make handling of overlapping packets match upstream. Signed-off-by:
-
Toke Høiland-Jørgensen authored
[ Upstream commit 4976e3c6 ] The logic in cake_select_tin() was getting a bit hairy, and it turns out we can simplify it quite a bit. This also allows us to get rid of one of the two diffserv parsing functions, which has the added benefit that already-zeroed DSCP fields won't get re-written. Suggested-by:
Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by:
Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by:
-
Pieter Jansen van Vuuren authored
[ Upstream commit 42cd5484 ] We no longer set CFI when pushing vlan tags, therefore we remove the CFI bit from push vlan. Fixes: 1a1e586f ("nfp: add basic action capabilities to flower offloads") Signed-off-by:
Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Signed-off-by:
Louis Peens <louis.peens@netronome.com> Signed-off-by:
-
Pieter Jansen van Vuuren authored
[ Upstream commit f7ee799a ] Replace vlan CFI bit with a vlan present bit that indicates the presence of a vlan tag. Previously the driver incorrectly assumed that an vlan id of 0 is not matchable, therefore we indicate vlan presence with a vlan present bit. Fixes: 5571e8c9 ("nfp: extend flower matching capabilities") Signed-off-by:
-
Toke Høiland-Jørgensen authored
[ Upstream commit c87b4ecd ] There is not actually any guarantee that the IP headers are valid before we access the DSCP bits of the packets. Fix this using the same approach taken in sch_dsmark. Reported-by:
Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk> Signed-off-by:
-
Toke Høiland-Jørgensen authored
[ Upstream commit b2100cc5 ] We shouldn't be using skb->protocol directly as that will miss cases with hardware-accelerated VLAN tags. Use the helper instead to get the right protocol number. Reported-by:
-
Jonathan Lemon authored
[ Upstream commit 9c69a132 ] When __ip6_rt_update_pmtu() is called, rt->from is RCU dereferenced, but is never checked for null - rt6_flush_exceptions() may have removed the entry. [ 1913.989004] RIP: 0010:ip6_rt_cache_alloc+0x13/0x170 [ 1914.209410] Call Trace: [ 1914.214798] <IRQ> [ 1914.219226] __ip6_rt_update_pmtu+0xb0/0x190 [ 1914.228649] ip6_tnl_xmit+0x2c2/0x970 [ip6_tunnel] [ 1914.239223] ? ip6_tnl_parse_tlv_enc_lim+0x32/0x1a0 [ip6_tunnel] [ 1914.252489] ? __gre6_xmit+0x148/0x530 [ip6_gre] [ 1914.262678] ip6gre_tunnel_xmit+0x17e/0x3c7 [ip6_gre] [ 1914.273831] dev_hard_start_xmit+0x8d/0x1f0 [ 1914.283061] sch_direct_xmit+0xfa/0x230 [ 1914.291521] __qdisc_run+0x154/0x4b0 [ 1914.299407] net_tx_action+0x10e/0x1f0 [ 1914.307678] __do_softirq+0xca/0x297 [ 1914.315567] irq_exit+0x96/0xa0 [ 1914.322494] smp_apic_timer_interrupt+0x68/0x130 [ 1914.332683] apic_timer_interrupt+0xf/0x20 [ 1914.341721] </IRQ> Fixes: a68886a6 ("net/ipv6: Make from in rt6_info rcu protected") Signed-off-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Reviewed-by:
Martin KaFai Lau <kafai@fb.com> Signed-off-by:
-
Saeed Mahameed authored
[ Upstream commit df3a8344 ] Flow is kfreed on mlx5_fpga_tls_del_flow but kept in the idr data structure, this is risky and can cause use-after-free, since the idr_remove is delayed until tls_send_teardown_cmd completion. Instead of delaying idr_remove, in this patch we do it on mlx5_fpga_tls_del_flow, before actually kfree(flow). Added synchronize_rcu before kfree(flow) Fixes: ab412e1d ("net/mlx5: Accel, add TLS rx offload routines") Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Jakub Kicinski authored
[ Upstream commit b4f47f38 ] Unlike '&&' operator, the '&' does not have short-circuit evaluation semantics. IOW both sides of the operator always get evaluated. Fix the wrong operator in tls_is_sk_tx_device_offloaded(), which would lead to out-of-bounds access for for non-full sockets. Fixes: 4799ac81 ("tls: Add rx inline crypto offload") Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
Saeed Mahameed authored
[ Upstream commit 31634bf5 ] To avoid use-after-free, hold the rcu read lock until we are done copying flow data into the command buffer. Fixes: ab412e1d ("net/mlx5: Accel, add TLS rx offload routines") Reported-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Matteo Croce authored
[ Upstream commit 1f227d16 ] The thunderx driver forbids to load an eBPF program if the MTU is too high, but this can be circumvented by loading the eBPF, then raising the MTU. Fix this by limiting the MTU if an eBPF program is already loaded. Fixes: 05c773f5 ("net: thunderx: Add basic XDP support") Signed-off-by:
Matteo Croce <mcroce@redhat.com> Acked-by:
Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by:
-
Matteo Croce authored
[ Upstream commit 5ee15c10 ] The thunderx driver splits frames bigger than 1530 bytes to multiple pages, making impossible to run an eBPF program on it. This leads to a maximum MTU of 1508 if QinQ is in use. The thunderx driver forbids to load an eBPF program if the MTU is higher than 1500 bytes. Raise the limit to 1508 so it is possible to use L2 protocols which need some more headroom. Fixes: 05c773f5 ("net: thunderx: Add basic XDP support") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit c543cb4a ] fib_compute_spec_dst() needs to be called under rcu protection. syzbot reported : WARNING: suspicious RCU usage 5.1.0-rc4+ #165 Not tainted include/linux/inetdevice.h:220 suspicious rcu_dereference_check() usage! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 1 lock held by swapper/0/0: #0: 0000000051b67925 ((&n->timer)){+.-.}, at: lockdep_copy_map include/linux/lockdep.h:170 [inline] #0: 0000000051b67925 ((&n->timer)){+.-.}, at: call_timer_fn+0xda/0x720 kernel/time/timer.c:1315 stack backtrace: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.1.0-rc4+ #165 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 lockdep_rcu_suspicious+0x153/0x15d kernel/locking/lockdep.c:5162 __in_dev_get_rcu include/linux/inetdevice.h:220 [inline] fib_compute_spec_dst+0xbbd/0x1030 net/ipv4/fib_frontend.c:294 spec_dst_fill net/ipv4/ip_options.c:245 [inline] __ip_options_compile+0x15a7/0x1a10 net/ipv4/ip_options.c:343 ipv4_link_failure+0x172/0x400 net/ipv4/route.c:1195 dst_link_failure include/net/dst.h:427 [inline] arp_error_report+0xd1/0x1c0 net/ipv4/arp.c:297 neigh_invalidate+0x24b/0x570 net/core/neighbour.c:995 neigh_timer_handler+0xc35/0xf30 net/core/neighbour.c:1081 call_timer_fn+0x190/0x720 kernel/time/timer.c:1325 expire_timers kernel/time/timer.c:1362 [inline] __run_timers kernel/time/timer.c:1681 [inline] __run_timers kernel/time/timer.c:1649 [inline] run_timer_softirq+0x652/0x1700 kernel/time/timer.c:1694 __do_softirq+0x266/0x95a kernel/softirq.c:293 invoke_softirq kernel/softirq.c:374 [inline] irq_exit+0x180/0x1d0 kernel/softirq.c:414 exiting_irq arch/x86/include/asm/apic.h:536 [inline] smp_apic_timer_interrupt+0x14a/0x570 arch/x86/kernel/apic/apic.c:1062 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:807 Fixes: ed0de45a ("ipv4: recompile ip options in ipv4_link_failure") Signed-off-by:
syzbot <syzkaller@googlegroups.com> Cc: Stephen Suryaputra <ssuryaextr@gmail.com> Signed-off-by:
-
Stephen Suryaputra authored
[ Upstream commit ed0de45a ] Recompile IP options since IPCB may not be valid anymore when ipv4_link_failure is called from arp_error_report. Refer to the commit 3da1ed7a ("net: avoid use IPCB in cipso_v4_error") and the commit before that (9ef6b42a) for a similar issue. Signed-off-by:
Stephen Suryaputra <ssuryaextr@gmail.com> Signed-off-by:
-
Jason Wang authored
[ Upstream commit 813dbeb6 ] We used to accept zero size iova range which will lead a infinite loop in translate_desc(). Fixing this by failing the request in this case. Reported-by: syzbot+d21e6e297322a900c128@syzkaller.appspotmail.com Fixes: 6b1e6cc7 ("vhost: new device IOTLB API") Signed-off-by:
Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Hoang Le authored
[ Upstream commit d1841533 ] When binding multiple services with specific type 1Ki, 2Ki.., this leads to some entries in the name table of publications missing when listed out via 'tipc name show'. The problem is at identify zero last_type conditional provided via netlink. The first is initial 'type' when starting name table dummping. The second is continuously with zero type (node state service type). Then, lookup function failure to finding node state service type in next iteration. To solve this, adding more conditional to marked as dirty type and lookup correct service type for the next iteration instead of select the first service as initial 'type' zero. Acked-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by:
-
Hangbin Liu authored
[ Upstream commit 43c2adb9 ] After adding a team interface to bridge, the team interface will enter promisc mode. Then if we add a new slave to team0, the slave will keep promisc off. Fix it by setting slave to promisc on if team master is already in promisc mode, also do the same for allmulti. v2: add promisc and allmulti checking when delete ports Fixes: 3d249d4c ("net: introduce ethernet teaming device") Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 50ce163a ] For some reason, tcp_grow_window() correctly tests if enough room is present before attempting to increase tp->rcv_ssthresh, but does not prevent it to grow past tcp_space() This is causing hard to debug issues, like failing the (__tcp_select_window(sk) >= tp->rcv_wnd) test in __tcp_ack_snd_check(), causing ACK delays and possibly slow flows. Depending on tcp_rmem[2], MTU, skb->len/skb->truesize ratio, we can see the problem happening on "netperf -t TCP_RR -- -r 2000,2000" after about 60 round trips, when the active side no longer sends immediate acks. This bug predates git history. Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Acked-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
Wei Wang <weiwan@google.com> Signed-off-by:
-
Lorenzo Bianconi authored
[ Upstream commit 988dc4a9 ] gue tunnels run iptunnel_pull_offloads on received skbs. This can determine a possible use-after-free accessing guehdr pointer since the packet will be 'uncloned' running pskb_expand_head if it is a cloned gso skb (e.g if the packet has been sent though a veth device) Fixes: a09a4c8d ("tunnels: Remove encapsulation offloads on decap") Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by:
-
Yuya Kusakabe authored
[ Upstream commit d85e8be2 ] skb_reorder_vlan_header() should move XDP meta data with ethernet header if XDP meta data exists. Fixes: de8f3a83 ("bpf: add meta pointer for direct access") Signed-off-by:
Yuya Kusakabe <yuya.kusakabe@gmail.com> Signed-off-by:
Takeru Hayasaka <taketarou2@gmail.com> Co-developed-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit c5b493ce ] br_multicast_start_querier() walks over the port list but it can be called from a timer with only multicast_lock held which doesn't protect the port list, so use RCU to walk over it. Fixes: c83b8fab ("bridge: Restart queries when last querier expires") Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 3b2e2904 ] When the commit below was introduced it changed two visible things: - the skb was no longer passed through the protocol handlers with the original device - the skb was passed up the stack with skb->dev = bridge The first change broke af_packet sockets on bridge ports. For example we use them for hostapd which listens for ETH_P_PAE packets on the ports. We discussed two possible fixes: - create a clone and pass it through NF_HOOK(), act on the original skb based on the result - somehow signal to the caller from the okfn() that it was called, meaning the skb is ok to be passed, which this patch is trying to implement via returning 1 from the bridge link-local okfn() Note that we rely on the fact that NF_QUEUE/STOLEN would return 0 and drop/error would return < 0 thus the okfn() is called only when the return was 1, so we signal to the caller that it was called by preserving the return value from nf_hook(). Fixes: 8626c56c ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict") Signed-off-by:
-
Gustavo A. R. Silva authored
[ Upstream commit 899537b7 ] arg is controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: net/atm/lec.c:715 lec_mcast_attach() warn: potential spectre issue 'dev_lec' [r] (local cap) Fix this by sanitizing arg before using it to index dev_lec. Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Si-Wei Liu authored
[ Upstream commit 8065a779 ] When a netdev appears through hot plug then gets enslaved by a failover master that is already up and running, the slave will be opened right away after getting enslaved. Today there's a race that userspace (udev) may fail to rename the slave if the kernel (net_failover) opens the slave earlier than when the userspace rename happens. Unlike bond or team, the primary slave of failover can't be renamed by userspace ahead of time, since the kernel initiated auto-enslavement is unable to, or rather, is never meant to be synchronized with the rename request from userspace. As the failover slave interfaces are not designed to be operated directly by userspace apps: IP configuration, filter rules with regard to network traffic passing and etc., should all be done on master interface. In general, userspace apps only care about the name of master interface, while slave names are less important as long as admin users can see reliable names that may carry other information describing the netdev. For e.g., they can infer that "ens3nsby" is a standby slave of "ens3", while for a name like "eth0" they can't tell which master it belongs to. Historically the name of IFF_UP interface can't be changed because there might be admin script or management software that is already relying on such behavior and assumes that the slave name can't be changed once UP. But failover is special: with the in-kernel auto-enslavement mechanism, the userspace expectation for device enumeration and bring-up order is already broken. Previously initramfs and various userspace config tools were modified to bypass failover slaves because of auto-enslavement and duplicate MAC address. Similarly, in case that users care about seeing reliable slave name, the new type of failover slaves needs to be taken care of specifically in userspace anyway. It's less risky to lift up the rename restriction on failover slave which is already UP. Although it's possible this change may potentially break userspace component (most likely configuration scripts or management software) that assumes slave name can't be changed while UP, it's relatively a limited and controllable set among all userspace components, which can be fixed specifically to listen for the rename events on failover slaves. Userspace component interacting with slaves is expected to be changed to operate on failover master interface instead, as the failover slave is dynamic in nature which may come and go at any point. The goal is to make the role of failover slaves less relevant, and userspace components should only deal with failover master in the long run. Fixes: 30c8bd5a ("net: Introduce generic failover module") Signed-off-by:
Si-Wei Liu <si-wei.liu@oracle.com> Reviewed-by:
Liran Alon <liran.alon@oracle.com> Acked-by:
Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by:
-
Sabrina Dubroca authored
[ Upstream commit 92480b39 ] When a bond is enslaved to another bond, bond_netdev_event() only handles the event as if the bond is a master, and skips treating the bond as a slave. This leads to a refcount leak on the slave, since we don't remove the adjacency to its master and the master holds a reference on the slave. Reproducer: ip link add bondL type bond ip link add bondU type bond ip link set bondL master bondU ip link del bondL No "Fixes:" tag, this code is older than git history. Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Signed-off-by:
-
- 20 Apr, 2019 1 commit
-
-
Greg Kroah-Hartman authored
-
