otherwise we loop forever if a PPPoE socket was set
to PPPOX_ZOMBIE state by a PADT message when the
ethernet device is going down afterwards.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6085 is identical to the mv88e6095, except that all ports are
10/100 Mb/s, so use the existing setup code except for the cpu/dsa speed
selection in _setup_port().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

properly record sk_rxhash in ipv6 sockets (v2)

Noticed while working on another project that flows to sockets which I had open
on a test systems weren't getting steered properly when I had RFS enabled.
Looking more closely I found that:

1) The affected sockets were all ipv6
2) They weren't getting steered because sk->sk_rxhash was never set from the
incomming skbs on that socket.

This was occuring because there are several points in the IPv4 tcp and udp code
which save the rxhash value when a new connection is established.  Those calls
to sock_rps_save_rxhash were never added to the corresponding ipv6 code paths.
This patch adds those calls.  Tested by myself to properly enable RFS
functionalty on ipv6.

Change notes:
v2:
	Filtered UDP to only arm RFS on bound sockets (Eric Dumazet)
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

adapter could remain uninitialized if probe fails for some reason.
A null pointer access could cause a crash if be_shutdown
is called after that.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch contains a fix for gracefully handling firmware heartbeat
failure instead of forcing panic.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an interrupt occurs, the INT pin is driven low by the
MCP251x controller (falling edge) but in some cases the INT
pin can be connected to the MPU through a transistor or level
translator which inverts this signal. In this case interrupt
should be configured in rising edge.

This patch adds support to pass the IRQ flags via
mcp251x_platform_data.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When SMSC911X_SAVE_MAC_ADDRESS flag is enabled the driver calls
smsc911x_mac_read and smsc911x_mac_read function without acquiring mac_lock
spinlock

This patch fixes following warning

smsc911x: Driver version 2008-10-21.
------------[ cut here ]------------
WARNING: at drivers/net/smsc911x.c:261 smsc911x_mac_read+0x24/0x220()
Modules linked in:
[<c0060858>] (unwind_backtrace+0x0/0xe0) from [<c009322c>] (warn_slowpath_common+0x4c/0x64)
[<c009322c>] (warn_slowpath_common+0x4c/0x64) from [<c009325c>] (warn_slowpath_null+0x18/0x1c)
[<c009325c>] (warn_slowpath_null+0x18/0x1c) from [<c0324bec>] (smsc911x_mac_read+0x24/0x220)
[<c0324bec>] (smsc911x_mac_read+0x24/0x220) from [<c0434788>] (smsc911x_read_mac_address+0x18/0x6c)
[<c0434788>] (smsc911x_read_mac_address+0x18/0x6c) from [<c0434c74>] (smsc911x_drv_probe+0x498/0x1788)
[<c0434c74>] (smsc911x_drv_probe+0x498/0x1788) from [<c02d3e54>] (platform_drv_probe+0x14/0x18)
[<c02d3e54>] (platform_drv_probe+0x14/0x18) from [<c02d2d60>] (driver_probe_device+0xc8/0x184)
[<c02d2d60>] (driver_probe_device+0xc8/0x184) from [<c02d2e84>] (__driver_attach+0x68/0x8c)
[<c02d2e84>] (__driver_attach+0x68/0x8c) from [<c02d1fc8>] (bus_for_each_dev+0x48/0x74)
[<c02d1fc8>] (bus_for_each_dev+0x48/0x74) from [<c02d2660>] (bus_add_driver+0x9c/0x228)
[<c02d2660>] (bus_add_driver+0x9c/0x228) from [<c02d3598>] (driver_register+0xa0/0x124)
[<c02d3598>] (driver_register+0xa0/0x124) from [<c0050668>] (do_one_initcall+0x94/0x168)
[<c0050668>] (do_one_initcall+0x94/0x168) from [<c0008984>] (kernel_init+0xa0/0x154)
[<c0008984>] (kernel_init+0xa0/0x154) from [<c005afac>] (kernel_thread_exit+0x0/0x8)
---[ end trace 2c931a35b7885770 ]---
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure dst_release() is not called with error pointer. This is
similar to commit 4910ac6c ("ipv4:
Don't ip_rt_put() an error pointer in RAW sockets.").
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A number of these devices have appeared "in the wild", and apparently
the Windows driver is perfectly happy to support this EEPROM version.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

{rx,tx}done_work's are only initialized for usb devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable@kernel.org
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some compiler/architecture combinations generate some warnings that are
not seen on my main system. Two of the "warnings" about unitialized variables
are really bugs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cc: <stable@kernel.org>
Reported-by: Mark Davis [via p54/devices wiki]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We were allocating the size of the NVS file struct and not checking
whether the length of the buffer passed was correct before copying it
into the allocated memory.  This is a security hole because buffer
overflows can occur if the userspace passes a bigger file than what is
expected.

With this patch, we check if the size of the data passed from
userspace matches the size required.

This bug was introduced in 2.6.36.

Cc: stable@kernel.org
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

2.6.38 added WARN_ON(in_irq) in del_timer_sync that triggers on zd1211rw when
reseting rx idle timer in urb completion handler.

Move timer reseting to tasklet.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Patch removes the bogus flag introduced by upstream commit
eefdbec1. Old code had buffer length check
that new code tried to handle with URB_SHORT_NOT_OK flag. With USB debugging
enabled bogus flag caused usb_submit_urb fail.

Remove URB_SHORT_NOT_OK flag and add buffer length check to urb completion
handler.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32092Reported-by: Jonathan Callen <abcd@gentoo.org>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cleaning the ieee80211_rx_data.flags field here is wrong, instead the
flags should be valid accross processing the frame on different
interfaces. Fix this by removing the incorrect flags=0 assignment.

Introduced in commit 554891e6
(mac80211: move packet flags into packet).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The description for buf_size was misleading and
just said you couldn't TX larger aggregates, but
of course you can't TX aggregates in a way that
would exceed the window either, which is possible
even if the aggregates are shorter than that.

Expand the description, thanks to Emmanuel for
explaining this to me.

Cc: Emmanuel Grumbach <egrumbach@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The phy information print during driver init time doesn't show
the numeric part of the chip name properly for AR9485. This patch
addresses this issue by adding the string to the respective array.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The MODULE_AUTHOR() macro in the main module (wl12xx) has been updated
to reflect one of the author's new email address, but the wl12xx_spi
and wl12xx_sdio modules haven't been updated.  This patches updates
them.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Otherwise, skb_put inside of dma_rx can fail...

	https://bugzilla.kernel.org/show_bug.cgi?id=32042Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@kernel.org

--ctdir ORIGINAL matches REPLY packets, and vv:

userspace sets "invert_flags &= ~XT_CONNTRACK_DIRECTION" in ORIGINAL
case.

Thus: (CTINFO2DIR(ctinfo) == IP_CT_DIR_ORIGINAL) ^
      !!(info->invert_flags & XT_CONNTRACK_DIRECTION))

yields "1 ^ 0", which is true -> returns false.

Reproducer:
iptables -I OUTPUT 1 -p tcp --syn -m conntrack --ctdir ORIGINAL
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>

This avoids pulling in the ipv6 module when using (ipv4-only) iptables
-m addrtype.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>

ipv6 fib lookup can set RT6_LOOKUP_F_IFACE flag to restrict search
to an interface, but this flag cannot be set via struct flowi.

Also, it cannot be set via ip6_route_output: this function uses the
passed sock struct to determine if this flag is required
(by testing for nonzero sk_bound_dev_if).

Work around this by passing in an artificial struct sk in case
'strict' argument is true.

This is required to replace the rt6_lookup call in xt_addrtype.c with
nf_afinfo->route().
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>

This is required to eventually replace the rt6_lookup call in
xt_addrtype.c with nf_afinfo->route().
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>

ipvsadm -ln --daemon will trigger a Null pointer exception because
ip_vs_genl_dump_daemons() uses skb_net() instead of skb_sknet().

To prevent others from NULL ptr a check is made in ip_vs.h skb_net().
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>

Static analyzer of clang found a dead store which appears to be a bug in
reading count of items in SEQOF field, only the lower byte of word is
stored. This may lead to corrupted read and communication shutdown.

The bug has been in the module since it's first inclusion into linux
kernel.

[Patrick: the bug is real, but without practical consequence since the
 largest amount of sequence-of members we parse is 30.]
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Patrick McHardy <kaber@trash.net>

The timeout variant of the list:set type must reference the member sets.
However, its garbage collector runs at timer interrupt so the mutex
protection of the references is a no go. Therefore the reference protection
is converted to rwlock.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>

- the timeout value was actually not set
- the garbage collector was broken

The variant is fixed, the tests to the ipset testsuite are added.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>

On error path kfree() should get pointer to memory allocated by
kmalloc() not the address of variable holding it (which is on stack).
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

All callers are prepared for alloc failures anyway, so this error
can safely be boomeranged to the callers domain without super
bad consequences. ...At worst the connection might go into a state
where each RTO tries to (unsuccessfully) re-fragment with such
a mis-sized value and eventually dies.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sometime the ASCONF_ACK parameters can equal to the fourfold of
ASCONF parameters, this only happend in some special case:

  ASCONF parameter is :
    Unrecognized Parameter (4 bytes)
  ASCONF_ACK parameter should be:
    Error Cause Indication parameter (8 bytes header)
     + Error Cause (4 bytes header)
       + Unrecognized Parameter (4bytes)

Four 4bytes Unrecognized Parameters in ASCONF chunk will cause panic.

Pid: 0, comm: swapper Not tainted 2.6.38-next+ #22 Bochs Bochs
EIP: 0060:[<c0717eae>] EFLAGS: 00010246 CPU: 0
EIP is at skb_put+0x60/0x70
EAX: 00000077 EBX: c09060e2 ECX: dec1dc30 EDX: c09469c0
ESI: 00000000 EDI: de3c8d40 EBP: dec1dc58 ESP: dec1dc2c
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process swapper (pid: 0, ti=dec1c000 task=c09aef20 task.ti=c0980000)
Stack:
 c09469c0 e1894fa4 00000044 00000004 de3c8d00 de3c8d00 de3c8d44 de3c8d40
 c09060e2 de25dd80 de3c8d40 dec1dc7c e1894fa4 dec1dcb0 00000040 00000004
 00000000 00000800 00000004 00000004 dec1dce0 e1895a2b dec1dcb4 de25d960
Call Trace:
 [<e1894fa4>] ? sctp_addto_chunk+0x4e/0x89 [sctp]
 [<e1894fa4>] sctp_addto_chunk+0x4e/0x89 [sctp]
 [<e1895a2b>] sctp_process_asconf+0x32f/0x3d1 [sctp]
 [<e188d554>] sctp_sf_do_asconf+0xf8/0x173 [sctp]
 [<e1890b02>] sctp_do_sm+0xb8/0x159 [sctp]
 [<e18a2248>] ? sctp_cname+0x0/0x52 [sctp]
 [<e189392d>] sctp_assoc_bh_rcv+0xac/0xe3 [sctp]
 [<e1897d76>] sctp_inq_push+0x2d/0x30 [sctp]
 [<e18a21b2>] sctp_rcv+0x7a7/0x83d [sctp]
 [<c077a95c>] ? ipv4_confirm+0x118/0x125
 [<c073a970>] ? nf_iterate+0x34/0x62
 [<c074789d>] ? ip_local_deliver_finish+0x0/0x194
 [<c074789d>] ? ip_local_deliver_finish+0x0/0x194
 [<c0747992>] ip_local_deliver_finish+0xf5/0x194
 [<c074789d>] ? ip_local_deliver_finish+0x0/0x194
 [<c0747a6e>] NF_HOOK.clone.1+0x3d/0x44
 [<c0747ab3>] ip_local_deliver+0x3e/0x44
 [<c074789d>] ? ip_local_deliver_finish+0x0/0x194
 [<c074775c>] ip_rcv_finish+0x29f/0x2c7
 [<c07474bd>] ? ip_rcv_finish+0x0/0x2c7
 [<c0747a6e>] NF_HOOK.clone.1+0x3d/0x44
 [<c0747cae>] ip_rcv+0x1f5/0x233
 [<c07474bd>] ? ip_rcv_finish+0x0/0x2c7
 [<c071dce3>] __netif_receive_skb+0x310/0x336
 [<c07221f3>] netif_receive_skb+0x4b/0x51
 [<e0a4ed3d>] cp_rx_poll+0x1e7/0x29c [8139cp]
 [<c072275e>] net_rx_action+0x65/0x13a
 [<c0445a54>] __do_softirq+0xa1/0x149
 [<c04459b3>] ? __do_softirq+0x0/0x149
 <IRQ>
 [<c0445891>] ? irq_exit+0x37/0x72
 [<c040a7e9>] ? do_IRQ+0x81/0x95
 [<c07b3670>] ? common_interrupt+0x30/0x38
 [<c0428058>] ? native_safe_halt+0xa/0xc
 [<c040f5d7>] ? default_idle+0x58/0x92
 [<c0408fb0>] ? cpu_idle+0x96/0xb2
 [<c0797989>] ? rest_init+0x5d/0x5f
 [<c09fd90c>] ? start_kernel+0x34b/0x350
 [<c09fd0cb>] ? i386_start_kernel+0xba/0xc1
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

auth_hmacs field of struct sctp_cookie is used for store
Requested HMAC Algorithm Parameter, and each HMAC Identifier
is 2 bytes, so the length should be:
  SCTP_AUTH_NUM_HMACS * sizeof(__u16) + 2
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_ethtool_get_rx_csum() won't report rx checksumming when it's not
changeable and driver is converted to hw_features and friends. Fix this.

(dev->hw_features & NETIF_F_RXCSUM) check is dropped - if the
ethtool_ops->get_rx_csum is set, then driver is not coverted, yet.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

The documentation for the USB ethernet devices suggests that
only some devices are supposed to use usb0 as the network interface
name instead of eth0. The logic used there, and documented in
Kconfig for CDC is that eth0 will be used when the mac address
is a globally assigned one, but usb0 is used for the locally
managed range that is typically used on point-to-point links.

Unfortunately, this has caused a lot of pain on the smsc95xx
device that is used on the popular pandaboard without an
EEPROM to store the MAC address, which causes the driver to
call random_ether_address().

Obviously, there should be a proper MAC addressed assigned to
the device, and discussions are ongoing about how to solve
this, but this patch at least makes sure that the default
interface naming gets a little saner and matches what the
user can expect based on the documentation, including for
new devices.

The approach taken here is to flag whether a device might be a
point-to-point link with the new FLAG_POINTTOPOINT setting in
the usbnet driver_info. A driver can set both FLAG_POINTTOPOINT
and FLAG_ETHER if it is not sure (e.g. cdc_ether), or just one
of the two.  The usbnet framework only looks at the MAC address
for device naming if both flags are set, otherwise it trusts the
flag.
Signed-off-by: Arnd Bergmann <arnd.bergmann@linaro.org>
Tested-by: Andy Green <andy.green@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now we have CONFIG_ARCH_DMA_ADDR_T_64BIT. We can fix the hacky
dma_addr_t size test cleanly.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 60d9f461 ("appletalk: remove
the BKL") added a dereference of "sk" before checking for NULL in
atalk_release().

Guard the code block completely, rather than partially, with the
NULL check.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should reduce the number of reserved completion queues from the total
number of entries. Since the queue size is power of two, not reducing the
reserved entries, caused a double queue size, which may lead to allocation
failures in some cases.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>