When handle_tx_event() encounters a COMP_MISSED_SERVICE_ERROR or
COMP_NO_PING_RESPONSE_ERROR event, it moves to 'goto cleanup'.
Here, it sets a flag, 'handling_skipped_tds', based on conditions that
exclude these two error events.

Subsequently, the process evaluates the loop that persists as long as
'handling_skipped_tds' remains true. However, since 'trb_comp_code' does
not change after its assignment, if it indicates either of the two error
conditions, the loop terminates immediately.

To simplify this process and enhance clarity, the modification involves
returning immediately upon detecting COMP_MISSED_SERVICE_ERROR or
COMP_NO_PING_RESPONSE_ERROR. This adjustment allows for the direct use of
'ep->skip', removing the necessity for the 'handling_skipped_tds' flag.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-12-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some transfer events don't always point to a TRB, and consequently don't
have a endpoint ring. In these cases, function handle_tx_event() should
not proceed, because if 'ep->skip' is set, the pointer to the endpoint
ring is used.

To prevent a potential failure and make the code logical, return after
checking the completion code for a Transfer event without TRBs.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-11-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If this quirk was set then driver would treat transfer events with
'Success' completion code as 'Short packet' if there were untransferred
bytes left.

This is so common that turn it into default behavior.

xhci_warn_ratelimited() is no longer used after this, so remove it.

A success event with untransferred bytes left doesn't always mean a
misbehaving controller. If there was an error mid a multi-TRB TD it's
allowed to issue a success event for the last TRB in that TD.

See xhci 1.2 spec 4.9.1 Transfer Descriptors

"Note: If an error is detected while processing a multi-TRB TD, the xHC
 shall generate a Transfer Event for the TRB that the error was detected
 on with the appropriate error Condition Code, then may advance to the
 next TD. If in the process of advancing to the next TD, a Transfer TRB
 is encountered with its IOC flag set, then the Condition Code of the
 Transfer Event generated for that Transfer TRB should be Success,
 because there was no error actually associated with the TRB that
 generated the Event. However, an xHC implementation may redundantly
 assert the original error Condition Code."
Co-developed-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-10-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Print the full hex value of PORTSC register in addition to the human
readable decoded string while debugging PORTSC value.

If PORTSC value is 0xffffffff then don't decode it.
This lets us inspect Rsvd bits of PORTSC.
Same is done for USBSTS register values.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-9-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace size_mul() with array_size() in memory allocation and freeing
processes, it fits better semantically.

Macro array_size() is identical to size_mult(), which clamps the max size,
so it's imperative that array_size() is used when freeing said memory.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-8-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

'erst_size' represents the maximum capacity of entries that ERST can hold,
while 'num_entries' indicates the actual number of entries currently held
in the ERST. These two values are identical because the xhci driver does
not support ERST expansion. Thus, 'erst_size' is removed.
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-7-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reduce the number of do-while loops by 1. The number of loops should be
number of segment + 1, the +1 is in case deq and enq are on the same
segment. But due to the use of a do-while loop, the expression is
evaluated after executing the loop, thus the loop is executed 1 extra
time.

Changing the do-while loop expression from "<=" to "<", reduces the loop
amount by 1. The expression "<=" would also work if it was a while loop
instead of a do-while loop.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-6-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Address debug message inaccuracies in xhci_ring_expansion_needed().
Specifically, remove the portion of the debug message that indicates the
number of enqueue TRBs to be added to the dequeue segment. This part of
the message may mislead and the calculated value is incorrect. Given that
this value is not of significant importance and the statement is not
consistently accurate, it has been omitted.

The specific issues with the debug message that this commit resolves:
- The calculation of the number of TRBs is incorrect. The current
  calculation erroneously includes the link TRB, which is reserved.
  Furthermore, the calculated number of TRBs can exceed the dequeue
  segment, resulting in a misleading debug message.

- The current phrasing suggests that "ring expansion by X is needed,
  adding X TRBs moves enqueue Y TRBs into the dequeue segment".
  The intended message, however, is "IF the ring is NOT expanded by X,
  THEN adding X TRBs moves enqueue Y TRBs into the dequeue segment".
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-5-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Check if requested segments ('segs' or 'ERST_DEFAULT_SEGS') exceeds the
maximum amount ERST supports.

When 'segs' is '0', 'ERST_DEFAULT_SEGS' is used instead. But both values
may not exceed ERST max.

Macro 'ERST_MAX_SEGS' is renamed to 'ERST_DEFAULT_SEGS'. The new name
better represents the macros, which is the number of Event Ring segments
to allocate, when the amount is not specified.

Additionally, rename and change xhci_create_secondary_interrupter()'s
argument 'int num_segs' to 'unsigned int segs'. This makes it the same
as its counter part in xhci_alloc_interrupter().

Fixes: c99b38c4 ("xhci: add support to allocate several interrupters")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-4-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This helper was only called from one function.
Removing it both reduces lines of code and made it more readable.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-3-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Port capability flags for USB2 ports have been cached in an
u32 xhci->ext_caps[] array long before the driver had struct xhci_port
and struct xhci_port_cap structures.

Move these cached USB2 port capability values together with the other
port capability values into struct xhci_port_cap cability structure.

This also gets rid of the cumbersome way of mapping port to USB2
capability based on portnum as each port has a pointer to its capability
structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-2-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Exynos-based Google Tensor gs101 SoC has a DWC3 compatible USB
controller and can reuse the existing Exynos glue. Add the
google,gs101-dwusb3 compatible and associated driver data. Four clocks
are required for USB for this SoC:
    * bus clock
    * suspend clock
    * Link interface AXI clock
    * Link interface APB clock
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240423-usb-dwc3-gs101-v1-2-2f331f88203f@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Exynos-based Google Tensor gs101 SoC has a DWC3 compatible USB
controller and can reuse the existing Exynos glue. Update the dt schema
to include the google,gs101-dwusb3 compatible for it.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240423-usb-dwc3-gs101-v1-1-2f331f88203f@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

interacting with "usb: misc: onboard_usb_hub: Disable the USB hub clock
on failure"
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20240424161202.7e45e19e@canb.auug.org.auSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Recent commit introduced support for reading Multiport PHYs and
while doing so iterated over an integer variable which runs from
[0-254] in the worst case scenario. But S390 compiler treats it as a
warning and complains that the integer write to string can go to 11
characters. Fix this by modifying iterator variable to u8.
Suggested-by: Johan Hovold <johan@kernel.org>
Fixes: 30a46746 ("usb: dwc3: core: Refactor PHY logic to support Multiport Controller")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404241215.Mib19Cu7-lkp@intel.com/Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240426050512.57384-1-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Power event IRQ is used for wakeup either when the controller is
SuperSpeed capable but is missing an SuperSpeed PHY interrupt, or when
the GIC is not capable of detecting DP/DM High-Speed PHY interrupts.

The Power event IRQ stat register indicates whether the High-Speed
phy entered and exited L2 successfully during suspend and resume.
Indicate the same for all ports of a multiport controller.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-10-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

DWC3 Qcom wrapper currently supports only wakeup configuration
for single port controllers. Read speed of each port connected
to the controller and enable wakeup for each of them accordingly.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-9-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On multiport supported controllers, each port has its own DP/DM and
SuperSpeed (if super speed capable) interrupts. As per the bindings,
their interrupt names differ from single-port ones by having a "_x"
added as suffix (x being the port number). Identify from the interrupt
names whether the controller is a multiport controller or not.
Refactor dwc3_qcom_setup_irq() call to parse multiportinterrupts along
with non-multiport ones accordingly.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-8-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The logic for requesting interrupts is duplicated for each interrupt. In
the upcoming patches that introduces support for multiport, it would be
better to clean up the duplication before reading mulitport related
interrupts.

Refactor interrupt setup call by adding a new helper function for
requesting the wakeup interrupts. To simplify implementation, make
the display name same as the interrupt name expected in Device tree.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-7-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the compatible string for SC8280 Multiport USB controller from
Qualcomm.

There are 4 power event interrupts supported by this controller
(one for each port of multiport controller). Add all the 4 as
non-optional interrupts for SC8280XP-MP

Also each port of multiport has one DP and one DM IRQ. Add all DP/DM
IRQs related to 4 ports of SC8280XP Teritiary controller.

Also added SuperSpeed PHY interrupt for both Superspeed ports.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-6-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the DWC3 driver supports only single port controller
which requires at least one HS PHY and at most one SS PHY.

But the DWC3 USB controller can be connected to multiple ports and
each port can have their own PHYs. Each port of the multiport
controller can either be HS+SS capable or HS only capable
Proper quantification of them is required to modify GUSB2PHYCFG
and GUSB3PIPECTL registers appropriately.

DWC3 multiport controllers are capable to service at most 15 High Speed
PHYs and 4 Supser Speed PHYs. Add support for detecting, obtaining and
configuring PHYs supported by a multiport controller.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-5-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On some SoC's like SA8295P where the tertiary controller is host-only
capable, GEVTADDRHI/LO, GEVTSIZ, GEVTCOUNT registers are not accessible.
Trying to access them leads to a crash.

For DRD/Peripheral supported controllers, event buffer setup is done
again in gadget_pullup. Skip setup or cleanup of event buffers if
controller is host-only capable.
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-4-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All DWC3 Multi Port controllers that exist today only support host mode.
Temporarily map XHCI address space for host-only controllers and parse
XHCI Extended Capabilities registers to read number of usb2 ports and
usb3 ports present on multiport controller. Each USB Port is at least HS
capable.

The port info for usb2 and usb3 phy are identified as num_usb2_ports
and num_usb3_ports and these are used as iterators for phy operations
and for modifying GUSB2PHYCFG/ GUSB3PIPECTL registers accordingly.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-3-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add bindings to indicate properties required to support multiport
on Synopsys DWC3 controller.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-2-quic_kriskura@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert USB UHCI bindings to DT schema. Documenting aspeed compatibles
and missing properties. Adding aspeed/generic-uhci example and fixing
nodename for the original example.
Signed-off-by: Mohammad Shehar Yaar Tausif <sheharyaar48@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240423150550.91055-1-sheharyaar48@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Update Qualcomm PMIC Type-C examples to follow the USB-C connector
schema. The USB-C connector should have three ports (USB HS @0,
SSTX/RX @1 and SBU @2 lanes). Reorder ports accordingly and add SBU port
connected to the SBU mux (e.g. FSA4480).
Reported-by: Luca Weiss <luca.weiss@fairphone.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240418-typec-fix-example-v3-1-08f649b6f368@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the usb/thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull char / misc driver fixes from Greg KH:
 "Here are some small char/misc and other driver fixes for 6.9-rc5.
  Included in here are the following:

   - binder driver fix for reported problem

   - speakup crash fix

   - mei driver fixes for reported problems

   - comdei driver fix

   - interconnect driver fixes

   - rtsx driver fix

   - peci.h kernel doc fix

  All of these have been in linux-next for over a week with no reported
  problems"

* tag 'char-misc-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  peci: linux/peci.h: fix Excess kernel-doc description warning
  binder: check offset alignment in binder_get_object()
  comedi: vmk80xx: fix incomplete endpoint checking
  mei: vsc: Unregister interrupt handler for system suspend
  Revert "mei: vsc: Call wake_up() in the threaded IRQ handler"
  misc: rtsx: Fix rts5264 driver status incorrect when card removed
  mei: me: disable RPL-S on SPS and IGN firmwares
  speakup: Avoid crash on very long word
  interconnect: Don't access req_list while it's being manipulated
  interconnect: qcom: x1e80100: Remove inexistent ACV_PERF BCM

Pull kernfs bugfix and documentation update from Greg KH:
 "Here are two changes for 6.9-rc5 that deal with "driver core" stuff,
  that do the following:

   - sysfs reference leak fix

   - embargoed-hardware-issues.rst update for Power

  Both of these have been in linux-next for over a week with no reported
  issues"

* tag 'driver-core-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  Documentation: embargoed-hardware-issues.rst: Add myself for Power
  fs: sysfs: Fix reference leak in sysfs_break_active_protection()

Pull tty/serial driver fixes from Greg KH:
 "Here are some small tty and serial driver fixes for 6.9-rc5 that
  resolve a bunch of reported problems. Included in here are:

   - MAINTAINERS and .mailmap update for Richard Genoud

   - serial core regression fixes from 6.9-rc1 changes

   - pci id cleanups

   - serial core crash fix

   - stm32 driver fixes

   - 8250 driver fixes

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: stm32: Reset .throttled state in .startup()
  serial: stm32: Return IRQ_NONE in the ISR if no handling happend
  serial: core: Fix missing shutdown and startup for serial base port
  serial: core: Clearing the circular buffer before NULLifying it
  MAINTAINERS: mailmap: update Richard Genoud's email address
  serial/pmac_zilog: Remove flawed mitigation for rx irq flood
  serial: 8250_pci: Remove redundant PCI IDs
  serial: core: Fix regression when runtime PM is not enabled
  serial: mxs-auart: add spinlock around changing cts state
  serial: 8250_dw: Revert: Do not reclock if already at correct rate
  serial: 8250_lpc18xx: disable clks on error in probe()

Pull USB / Thunderbolt driver fixes from Greg KH:
 "Here are some small USB and Thunderbolt driver fixes for 6.9-rc5.
  Included in here are:

   - MAINTAINER file update for invalid email address

   - usb-serial device id updates

   - typec driver fixes

   - thunderbolt / usb4 driver fixes

   - usb core shutdown fixes

   - cdc-wdm driver revert for reported problem in -rc1

   - usb gadget driver fixes

   - xhci driver fixes

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'usb-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  USB: serial: option: add Telit FN920C04 rmnet compositions
  usb: dwc3: ep0: Don't reset resource alloc flag
  Revert "usb: cdc-wdm: close race between read and workqueue"
  USB: serial: option: add Rolling RW101-GL and RW135-GL support
  USB: serial: option: add Lonsung U8300/U9300 product
  USB: serial: option: add support for Fibocom FM650/FG650
  USB: serial: option: support Quectel EM060K sub-models
  USB: serial: option: add Fibocom FM135-GL variants
  usb: misc: onboard_usb_hub: Disable the USB hub clock on failure
  thunderbolt: Avoid notify PM core about runtime PM resume
  thunderbolt: Fix wake configurations after device unplug
  usb: dwc2: host: Fix dereference issue in DDMA completion flow.
  usb: typec: mux: it5205: Fix ChipID value typo
  MAINTAINERS: Drop Li Yang as their email address stopped working
  usb: gadget: fsl: Initialize udc before using it
  usb: Disable USB3 LPM at shutdown
  usb: gadget: f_ncm: Fix UAF ncm object at re-bind after usb ep transport error
  usb: typec: tcpm: Correct the PDO counting in pd_set
  usb: gadget: functionfs: Wait for fences before enqueueing DMABUF
  usb: gadget: functionfs: Fix inverted DMA fence direction
  ...

Pull scheduler fix from Borislav Petkov:

 - Add a missing memory barrier in the concurrency ID mm switching

* tag 'sched_urgent_for_v6.9_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Add missing memory barrier in switch_mm_cid

Pull x86 fixes from Borislav Petkov:

 - Fix CPU feature dependencies of GFNI, VAES, and VPCLMULQDQ

 - Print the correct error code when FRED reports a bad event type

 - Add a FRED-specific INT80 handler without the special dances that
   need to happen in the current one

 - Enable the using-the-default-return-thunk-but-you-should-not warning
   only on configs which actually enable those special return thunks

 - Check the proper feature flags when selecting BHI retpoline
   mitigation

* tag 'x86_urgent_for_v6.9_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpufeatures: Fix dependencies for GFNI, VAES, and VPCLMULQDQ
  x86/fred: Fix incorrect error code printout in fred_bad_type()
  x86/fred: Fix INT80 emulation for FRED
  x86/retpolines: Enable the default thunk warning only on relevant configs
  x86/bugs: Fix BHI retpoline check

Pull block fixes from Jens Axboe:
 "Just two minor fixes that should go into the 6.9 kernel release, one
  fixing a regression with partition scanning errors, and one fixing a
  WARN_ON() that can get triggered if we race with a timer"

* tag 'block-6.9-20240420' of git://git.kernel.dk/linux:
  blk-iocost: do not WARN if iocg was already offlined
  block: propagate partition scanning errors to the BLKRRPART ioctl

Pull email address update from James Bottomley:
 "My IBM email has stopped working, so update to a working email
  address"

* tag 'email' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  MAINTAINERS: update to working email address

Pull kvm fixes from Paolo Bonzini:
 "This is a bit on the large side, mostly due to two changes:

   - Changes to disable some broken PMU virtualization (see below for
     details under "x86 PMU")

   - Clean up SVM's enter/exit assembly code so that it can be compiled
     without OBJECT_FILES_NON_STANDARD. This fixes a warning "Unpatched
     return thunk in use. This should not happen!" when running KVM
     selftests.

  Everything else is small bugfixes and selftest changes:

   - Fix a mostly benign bug in the gfn_to_pfn_cache infrastructure
     where KVM would allow userspace to refresh the cache with a bogus
     GPA. The bug has existed for quite some time, but was exposed by a
     new sanity check added in 6.9 (to ensure a cache is either
     GPA-based or HVA-based).

   - Drop an unused param from gfn_to_pfn_cache_invalidate_start() that
     got left behind during a 6.9 cleanup.

   - Fix a math goof in x86's hugepage logic for
     KVM_SET_MEMORY_ATTRIBUTES that results in an array overflow
     (detected by KASAN).

   - Fix a bug where KVM incorrectly clears root_role.direct when
     userspace sets guest CPUID.

   - Fix a dirty logging bug in the where KVM fails to write-protect
     SPTEs used by a nested guest, if KVM is using Page-Modification
     Logging and the nested hypervisor is NOT using EPT.

  x86 PMU:

   - Drop support for virtualizing adaptive PEBS, as KVM's
     implementation is architecturally broken without an obvious/easy
     path forward, and because exposing adaptive PEBS can leak host LBRs
     to the guest, i.e. can leak host kernel addresses to the guest.

   - Set the enable bits for general purpose counters in
     PERF_GLOBAL_CTRL at RESET time, as done by both Intel and AMD
     processors.

   - Disable LBR virtualization on CPUs that don't support LBR
     callstacks, as KVM unconditionally uses
     PERF_SAMPLE_BRANCH_CALL_STACK when creating the perf event, and
     would fail on such CPUs.

  Tests:

   - Fix a flaw in the max_guest_memory selftest that results in it
     exhausting the supply of ucall structures when run with more than
     256 vCPUs.

   - Mark KVM_MEM_READONLY as supported for RISC-V in
     set_memory_region_test"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
  KVM: Drop unused @may_block param from gfn_to_pfn_cache_invalidate_start()
  KVM: selftests: Add coverage of EPT-disabled to vmx_dirty_log_test
  KVM: x86/mmu: Fix and clarify comments about clearing D-bit vs. write-protecting
  KVM: x86/mmu: Remove function comments above clear_dirty_{gfn_range,pt_masked}()
  KVM: x86/mmu: Write-protect L2 SPTEs in TDP MMU when clearing dirty status
  KVM: x86/mmu: Precisely invalidate MMU root_role during CPUID update
  KVM: VMX: Disable LBR virtualization if the CPU doesn't support LBR callstacks
  perf/x86/intel: Expose existence of callback support to KVM
  KVM: VMX: Snapshot LBR capabilities during module initialization
  KVM: x86/pmu: Do not mask LVTPC when handling a PMI on AMD platforms
  KVM: x86: Snapshot if a vCPU's vendor model is AMD vs. Intel compatible
  KVM: x86: Stop compiling vmenter.S with OBJECT_FILES_NON_STANDARD
  KVM: SVM: Create a stack frame in __svm_sev_es_vcpu_run()
  KVM: SVM: Save/restore args across SEV-ES VMRUN via host save area
  KVM: SVM: Save/restore non-volatile GPRs in SEV-ES VMRUN via host save area
  KVM: SVM: Clobber RAX instead of RBX when discarding spec_ctrl_intercepted
  KVM: SVM: Drop 32-bit "support" from __svm_sev_es_vcpu_run()
  KVM: SVM: Wrap __svm_sev_es_vcpu_run() with #ifdef CONFIG_KVM_AMD_SEV
  KVM: SVM: Create a stack frame in __svm_vcpu_run() for unwinding
  KVM: SVM: Remove a useless zeroing of allocated memory
  ...

Pull powerpc fixes from Michael Ellerman:

 - Fix wireguard loading failure on pre-Power10 due to Power10 crypto
   routines

 - Fix papr-vpd selftest failure due to missing variable initialization

 - Avoid unnecessary get/put in spapr_tce_platform_iommu_attach_dev()

Thanks to Geetika Moolchandani, Jason Gunthorpe, Michal Suchánek, Nathan
Lynch, and Shivaprasad G Bhat.

* tag 'powerpc-6.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  selftests/powerpc/papr-vpd: Fix missing variable initialization
  powerpc/crypto/chacha-p10: Fix failure on non Power10
  powerpc/iommu: Refactor spapr_tce_platform_iommu_attach_dev()

Pull clk fixes from Stephen Boyd:
 "A couple clk driver fixes, a build fix, and a deadlock fix:

   - Mediatek mt7988 has broken PCIe because the wrong parent is used

   - Mediatek clk drivers may deadlock when registering their clks
     because the clk provider device is repeatedly runtime PM resumed
     and suspended during probe and clk registration.

     Resuming the clk provider device deadlocks with an ABBA deadlock
     due to genpd_lock and the clk prepare_lock. The fix is to keep the
     device runtime resumed while registering clks.

   - Another runtime PM related deadlock, this time with disabling
     unused clks during late init.

     We get an ABBA deadlock where a device is runtime PM resuming (or
     suspending) while the disabling of unused clks is happening in
     parallel. That runtime PM action calls into the clk framework and
     tries to grab the clk prepare_lock while the disabling of unused
     clks holds the prepare_lock and is waiting for that runtime PM
     action to complete.

     The fix is to runtime resume all the clk provider devices before
     grabbing the clk prepare_lock during disable unused.

   - A build fix to provide an empty devm_clk_rate_exclusive_get()
     function when CONFIG_COMMON_CLK=n"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: mediatek: mt7988-infracfg: fix clocks for 2nd PCIe port
  clk: mediatek: Do a runtime PM get on controllers during probe
  clk: Get runtime PM before walking tree for clk_summary
  clk: Get runtime PM before walking tree during disable_unused
  clk: Initialize struct clk_core kref earlier
  clk: Don't hold prepare_lock when calling kref_put()
  clk: Remove prepare_lock hold assertion in __clk_release()
  clk: Provide !COMMON_CLK dummy for devm_clk_rate_exclusive_get()

jejb@linux.ibm.com no longer works.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>