This branch acts as a base for adding USB support to
r8A7778/BOCK-W and r8A7779/Marzen.

It includes the soc branch to provide dependencies in
the r8A7778 clock code.

It includes pinmux to provide pinmux initialisation for Bock-W
which is a dependency.

Conflicts:
	arch/arm/mach-shmobile/Kconfig
	arch/arm/mach-shmobile/include/mach/r8a7778.h
	arch/arm/mach-shmobile/setup-r8a7778.c

According to the datasheet, it is not allowed to change div4 clock rates
if an earlier rate change operation is still in progress, as indicated by
a set kick bit.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

An earlier commit "ARM: shmobile: sh73a0: add support for adjusting CPU
frequency" intended to replace some clock operations only for the Z-clock,
instead it replaced them for all div4 clocks, since all div4 clocks share
the same copy of clock operations. Fix this by using a separate clock
operations structure for Z-clock.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Break out the function sh73a0_init_delay() that now
gets called both for the C version of the code and
the DT -reference boards. This way we handle both
cases in the same way.

Allows us to boot with TWD only in the kernel configuration
for C board code. TWD is not yet enabled in the case of
DT -reference - this due to a dependency on CCF.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch enables the use of the generic cpufreq-cpu0 driver on sh73a0.
Providing a regulator, a list of OPPs in DT, combined with a virtual
cpufreq-cpu0 platform device and a clock, attached to it is everything,
the cpufreq-cpu0 driver needs. The first sh73a0 platform, implementing
such CPUFreq support is kzm9g-reference.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

On SH73A0 the output of PLL0 is supplied to two dividers, feeding clock to
the CPU core and SGX. Lower CPU frequencies allow the use of lower supply
voltages and thus reduce power consumption.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Both clock-r8a7740.c and clock-r8a7790.c define a div4_clks array as
non-static. Compiling support for both SoCs thus result in a symbol
redefinition. Fix it by defining the arrays as static.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV6 clocks control SD*/MMC* core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV4 clocks control SD* core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Almost all clock needs main clock which is basis clock on r8a7790.
This patch adds it, and, set its parent/ratio via MD pin.
It is based on v0.05 datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds SDHI register function which needs id number (= 0/1/2)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

R-Car M1 has many clocks, and it is possible to
read/use clock ratio of these clocks from FRQMRx.
But, these ratio are fixed value and
these are decided by MD pin status.

This patch reads MD pin status,
and used fixed ratio clock for other clocks.
It was tesed on bock-w board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV6 clocks control each core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV4 clocks control each core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

PLL clocks are basis clock for other clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Almost all clock needs main clock which is basis clock on r8a73a4.
This patch adds it, and, set parent clock via CKSCR register.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add clock association for i2c0 and i2c1 for the new DT names.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When we use the ethernet device via DT setup, we need to add it
to a lookup list until this is properly handled later in a DT-only
fashion.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Ether setup code position was scattering.
This patch fixes it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

SH_CLK_SET_RATIO() will be trouble without this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Convert code to use DEFINE_RES_MEM*() macros.
These macros were already used in this file,
this change makes their usage consistent throughout the file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The correct model name is R-Car M1A or R8A77781; R8A77780 corresponds to R-Car
M1S which is a SH based SoC.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: manually applied]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Both clock-r8a7740.c and clock-r8a7790.c define a div4_clks array as
non-static. Compiling support for both SoCs thus result in a symbol
redefinition. Fix it by defining the arrays as static.

To avoid further similar issues, also define the main_clks as static.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Replace hardcoded pin numbers with the RCAR_GP_PIN macro to make the
code match the documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Initialize r8a7790 pinmuxing and register mappings for the two debug
serial ports.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

SCIF0 support as 1st step
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

sh73a0 needs "sh_fsi2", not "sh_fsi2.0"
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use DEFINE_RES_MEM() and platform_device_register_simple()
to save a couple of lines of code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

"gpio-rcar: Support IRQ_TYPE_EDGE_BOTH" adds support to the R-Car GPIO
driver for IRQ_TYPE_EDGE_BOTH. As hardware support for this feature is
not universal for all SoCs a flag, has_both_edge_trigger, has been
added to the platform data of the driver to allow this feature to be
enabled.

As the r8a7790 SoC hardware supports this feature enable it.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The list of functions selected by the MOD_SEL2 register was missing
an entry. This caused all entries after this to modify the MOD_SEL2
register incorrectly.

This bug showed up when selecting i2c2_c pins on the Renesas Hurricane board.

This bug has been present since pinmux support was added for the
r8a7779 SoC by 881023d2 ("sh-pfc: Add
r8a7779 pinmux support") in v3.8-rc4.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

GPIOLIB dependency handling was added to the PINCTRL core by

commit 2afe8229
Author: Haojian Zhuang <haojian.zhuang@linaro.org>
Date:   Thu Mar 28 07:34:19 2013 +0800

    pinctrl: core: add dependence of GPIOLIB

There is not need to handle that dependency at the SH Mobile level
anymore. Revert

commit 6722f6cb
Author: Magnus Damm <damm@opensource.se>
Date:   Mon Mar 18 22:58:18 2013 +0900

    ARM: shmobile: Disallow PINCTRL without GPIOLIB

    Modify mach-shmobile to only select PINCTRL in case of
    ARCH_WANT_OPTIONAL_GPIOLIB is set.

    This fixes a build error triggered when adding a new SoC
    lacking GPIO software support (ARCH_WANT_OPTIONAL_GPIOLIB=n):
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds pinmux groups and functions for the two MMCIF and four
SDHI interfaces on r8a73a4 (APE6).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add MMCIF CLK/CMD/DATA groups to R8A7778 PFC driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add HSPI CLK/CS/RX/TX pin groups to R8A7778 PFC driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add I2C SDA/SCL pin groups to R8A7778 PFC driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>