There's no reason to have the uframe scheduler off on dwc2.  Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".

The uframe scheduler has been off on HiSilicon since commit
37dd9d65 ("usb: dwc2: add support of hi6220").  Since then there
have been many many improvements, notably the commit 9f9f09b0
("usb: dwc2: host: Totally redo the microframe scheduler")

Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There's no reason to have the uframe scheduler off on dwc2.  Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".

The uframe scheduler has been off on Broadcom since commit
58b179dc ("staging: dwc2: disable uframe_sched on the bcm2835").
Since then there have been many many improvements, notably the commit
9f9f09b0 ("usb: dwc2: host: Totally redo the microframe
scheduler")

Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

To start ISOC transfers in handlers dwc2_gadget_handle_nak() and
dwc2_gadget_handle_out_token_ep_disabled() driver reads current frame
number, based on which, set target frame number to start first ISOC
transfer.

In case if system's high IRQ latency and multiple EP's asserted
interrupt in same frame, there are high probability that when reading
current frame number in EP's handlers, actual frame number can be
increased. As result for bInterval > 1, starting target frame
will be set wrongly and all ISOC packets will be dropped.

In patch "usb: dwc2: Change reading of current frame number flow"
reading of current frame number done ASAP in common interrupt handler.
This frame number stored in frame_number variable which used as
starting frame number for ISOC EP's in above mentioned handlers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Declared dwc2_check_core_endianness() function for dynamicly check
core endianness.
Added needs_byte_swap flag to hsotg structure, and depending on
flag swap value inside dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

By default when core sees any transaction error (CRC or overflow) it
replies with terminating retry ACK (Retry=1 and Nump == 0).

Enabling this Auto Retry feature in controller will make the core send
a non-terminanting ACK upon such transaction errors. That is, ACK TP
with Retry=1 and Nump != 0.

Doing so will give controller a chance to recover from transient error
conditions.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dwc_usb31 does not support OTG mode. If the controller supports DRD but
the dr_mode is not specified or set to OTG, then set the mode to
peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds role switch support for R-Car SoCs into the USB 3.0
peripheral driver. Some R-Car SoCs (e.g. R-Car H3) have USB 3.0
dual-role device controller which has the USB 3.0 xHCI host and
Renesas USB 3.0 peripheral.

Unfortunately, the mode change register (DRD_CON) contains
the USB 3.0 peripheral controller side only. So, this renesas_usb3
driver manages the DRD_CON now. However, in peripheral mode, the host
should stop. Also the host hardware needs to reinitialize its own
registers when the mode changes from peripheral to host mode.
Otherwise, the host cannot work correctly (e.g. detect a device
as high-speed).

To achieve this reinitialization by a driver, this driver also
registers a role switch driver to manage the DRD_CON and get
a device pointer of usb 3.0 host from "companion" property of OF.
Then, when the usb role is changed, renesas_usb3_role_switch_set()
will attach/release the xhci-plat driver to reinitialize the host
hardware.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dwc2_readl_rep/dwc2_writel_rep functions using readl/writel in a
loop.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added hsotg argument to dwc2_readl/writel function prototype,
and also instead of address pass offset of register.
hsotg will contain flag field for endianness.

Also customized dwc2_set_bit and dwc2_clear_bit function for
dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

On Intel Edison board the OTG function is enabled, thus,
USB can switch to the host mode.

Allow that by changing dr_mode property to "otg" for Intel Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

For now all PCI enumerated dwc3 devices require some properties
to be present. This allows us to unconditionally append them and supply
via driver_data.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add description of 'snps,incr-burst-type-adjustment' to binding
so that configuring devicetree.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add the macro definition for global soc bus configuration
register 0
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Describe 'wakeup_work' field of struct dwc3_pci to avoid a warning:

drivers/usb/dwc3/dwc3-pci.c:59: warning: Function parameter or member 'wakeup_work' not described in 'dwc3_pci'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Commit ff3f0789 ("usb: dwc3: use BIT() macro where possible")
changed DWC3_DEPCFG_STREAM_EVENT_EN from bit 13 to bit 12.

Spotted this cleanup typo while looking at diffs between 4.9.35 and
4.14.16 for a separate issue.

Fixes: ff3f0789 ("usb: dwc3: use BIT() macro where possible")
Signed-off-by: Erich E. Hoover <ehoover@sweptlaser.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If we power off the SoC logic rail in S3, we can find that the Type-C
PHY can't initialize correctly after system resume. We need to toggle
the USB3-OTG reset before trying to initialize the PHY, or else it
times out.

    phy phy-ff800000.phy.9: phy poweron failed --> -110
    dwc3 fe900000.dwc3: failed to initialize core
    dwc3: probe of fe900000.dwc3 failed with error -110

Note that the RK3399 TRM suggests that we should keep the whole usb3
controller in reset for the duration of the Type-C PHY initialization.
However, it's hard to assert the reset in the current framework of
reset. We're still skeptical about that, and we haven't yet found a
case where this seems to have mattered. This approach is much easier, it
simply holds the USB3-OTG reset while device is supended.

The dwc3 core is going to reinitialize the controller at suspend/resume
anyway (including a "soft reset"), so it should be safe to do this.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The kref used to be needed because sharing of fsg_common among multiple USB
function instances was handled by fsg. Now this is managed by configfs, we
don't need it anymore. So let's eliminate kref from this driver.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

fsg_common_set_num_buffers() may fail due to ENOMEM. So add
error handling for fail case.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Even though we only use them once, it is better to not put/release
the GPIOs immediately after use, so that others cannot claim them.

Use devm functions to get the phy GPIOs, so that they will be
automatically released when were unbound from the device and
remove the gpio_put calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

On some Bay Trail (BYT) systems the firmware does not enable the
ULPI Refclk.

This commit adds a helper which checks and if necessary enabled the Refclk
and calls this helper for BYT machines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Bay Trail / BYT SoCs do not have a builtin device-mode phy, instead
they require an external ULPI phy for device-mode.

Only some BYT devices have an external phy, but even on those devices
device-mode is not working because the dwc3 does not see the phy.

The problem is that the ACPI fwnode for the dwc3 does not contain the
expected GPIO resources for the GPIOs connected to the chip-select and
reset pins of the phy.

I've found the workaround which some Android x86 kernels use for this:
https://github.com/BORETS24/Kernel-for-Asus-Zenfone-2/blob/master/arch/x86/platform/intel-mid/device_libs/pci/platform_usb_otg.c
Which boils down to hardcoding the GPIOs for these devices.

The good news it that all boards (*) use the same GPIOs.

This commit fixes the ULPI phy not woring by adding a gpiod_lookup_table
call which adds a hardcoded mapping for BYT devices. Note that the mapping
added by gpiod_add_lookup_table is a fallback mapping, so boards which
properly provide GPIO resources in the ACPI firmware-node resources
will not use this.

*) Except for the first revision of the evalulation-kit, which normal users
don't have
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This documentation patch specifies that certain USB gadget endpoint
operations may be called in interrupt context:

	usb_ep_queue, usb_ep_dequeue, usb_ep_set_halt,
	usb_ep_clear_halt, usb_ep_set_wedge, usb_ep_fifo_status,
	and usb_ep_fifo_flush;

while others must be called in process context:

	usb_ep_enable and usb_ep_disable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This fixes the following checkpatch error:

ERROR: code indent should use tabs where possible

Here, spaces are replaced by a tab in 2 lines.
Signed-off-by: Parth Y Shah <sparth1292@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This driver is to be used for Synopsys PCIe-base HAPS platform. Move the
the HAPS support from dwc3-pci to this driver.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.

It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.

This manifests as the following bugs:

Prior to 946ef68a ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.

After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.

Fixes: 946ef68a ("Let setup() return USB_GADGET_DELAYED_STATUS")
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When utilising multiple instantiations of a UVC gadget on a composite
device, there is no clear method to link a particular configuration to
its respective video node.

Provide a means for identifying the correct video node by exposing the
name of the function configuration through sysfs.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The to_f_uvc_opts() function is forward-declared without needing to, as
its definition can simply be moved up in the file. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Moved dwc2_readl/writel functions after hsotg declaration for
adding hsotg structure to dwc2_readl/writel function prototypes.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Trivial fix to spelling mistake in usbg_us_strings array
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The trace module parameter controls output of debugging messages in the
UVC function driver. Move it from the webcam module to the UVC function
module where it belongs. This allows ConfigFS-based UVC gadgets to
control tracing.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In order to speed up compilation, only include the headers that are
strictly required within other headers. To that end, use forward
structure declaration and move #include statements to .c file as
appropriate.

While at it, sort headers alphabetically, and remove unneeded __KERNEL__
guards.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The UVC gadget userspace API (V4L2 events and custom ioctls) is defined
in a header internal to the kernel. Move it to a new public header to
make it accessible to userspace.

The UVC_INTF_CONTROL and UVC_INTF_STREAMING macros are not used, so
remove them in the process.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull NVMe fixes from Christoph Hellwig:

 - fix a regression in 4.18 that causes a memory leak on probe failure
   (Keith Bush)

 - fix a deadlock in the passthrough ioctl code (Scott Bauer)

 - don't enable AENs if not supported (Weiping Zhang)

 - fix an old regression in metadata handling in the passthrough ioctl
   code (Roland Dreier)

* tag 'nvme-for-4.18' of git://git.infradead.org/nvme:
  nvme: fix handling of metadata_len for NVME_IOCTL_IO_CMD
  nvme: don't enable AEN if not supported
  nvme: ensure forward progress during Admin passthru
  nvme-pci: fix memory leak on probe failure

Pull vfs fixes from Al Viro:
 "Fix several places that screw up cleanups after failures halfway
  through opening a file (one open-coding filp_clone_open() and getting
  it wrong, two misusing alloc_file()). That part is -stable fodder from
  the 'work.open' branch.

  And Christoph's regression fix for uapi breakage in aio series;
  include/uapi/linux/aio_abi.h shouldn't be pulling in the kernel
  definition of sigset_t, the reason for doing so in the first place had
  been bogus - there's no need to expose struct __aio_sigset in
  aio_abi.h at all"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  aio: don't expose __aio_sigset in uapi
  ocxlflash_getfile(): fix double-iput() on alloc_file() failures
  cxl_getfile(): fix double-iput() on alloc_file() failures
  drm_mode_create_lease_ioctl(): fix open-coded filp_clone_open()

kernel_wait4() expects a userland address for status - it's only
rusage that goes as a kernel one (and needs a copyout afterwards)

[ Also, fix the prototype of kernel_wait4() to have that __user
  annotation   - Linus ]

Fixes: 92ebce5a ("osf_wait4: switch to kernel_wait4()")
Cc: stable@kernel.org # v4.13+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC fixes from Olof Johansson:

 - Fix interrupt type on ethernet switch for i.MX-based RDU2

 - GPC on i.MX exposed too large a register window which resulted in
   userspace being able to crash the machine.

 - Fixup of bad merge resolution moving GPIO DT nodes under pinctrl on
   droid4.

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: imx6: RDU2: fix irq type for mv88e6xxx switch
  soc: imx: gpc: restrict register range for regmap access
  ARM: dts: omap4-droid4: fix dts w.r.t. pwm

Pull x86 fix from Ingo Molnar:
 "A single fix for a MCE-polling regression, which prevented the
  disabling of polling"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/MCE: Remove min interval polling limitation