When a TC's PFC is disabled or enabled, the RX private buffer for
this TC need to be changed too, otherwise this may cause packet
dropped problem.

This patch fixes it by calling hclge_buffer_alloc to reallocate
buffer when pfc_en changes.

Fixes: cacde272 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, hns3 driver just directly send specific setting bit
and mask bits of MAC VLAN switch parameter to the firmware, it
can not be compatible with the old firmware, because the old one
ignores mask bits and covers all bits with new setting bits.
So when running with old firmware, the communication between PF
and VF will fail after resetting or configuring spoof check, since
they will do the MAC VLAN switch parameter configuration.

This patch fixes this problem by reading switch parameter firstly,
then just modifies the corresponding bit and sends it to firmware.

Fixes: dd2956ea ("net: hns3: not allow SSU loopback while execute ethtool -t dev")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pre-allocates buffers sufficient for the maximum supported MTU (2026) in
order to eliminate the possibility of resource exhaustion when changing the
MTU while the device is up.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tipc prefix for log messages generated by tipc was
removed in commit 07f6c4bc ("tipc: convert tipc reference
table to use generic rhashtable").

This is still a useful prefix so add it back.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.4-20191114' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2019-11-14

here another pull request for net/master consisting of one patch (including my S-o-b).

Jouni Hogander's patch fixes a memory leak found by the syzbot in the slcan
driver's error path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-2019-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.4

Hopefully last fixes for v5.4, only one iwlwifi fix this time.

iwlwifi

* fix A-MSDU data corruption when using CCMP/GCMP ciphers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is fixing memory leak reported by Syzkaller:

BUG: memory leak unreferenced object 0xffff888067f65500 (size 4096):
  comm "syz-executor043", pid 454, jiffies 4294759719 (age 11.930s)
  hex dump (first 32 bytes):
    73 6c 63 61 6e 30 00 00 00 00 00 00 00 00 00 00 slcan0..........
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
  backtrace:
    [<00000000a06eec0d>] __kmalloc+0x18b/0x2c0
    [<0000000083306e66>] kvmalloc_node+0x3a/0xc0
    [<000000006ac27f87>] alloc_netdev_mqs+0x17a/0x1080
    [<0000000061a996c9>] slcan_open+0x3ae/0x9a0
    [<000000001226f0f9>] tty_ldisc_open.isra.1+0x76/0xc0
    [<0000000019289631>] tty_set_ldisc+0x28c/0x5f0
    [<000000004de5a617>] tty_ioctl+0x48d/0x1590
    [<00000000daef496f>] do_vfs_ioctl+0x1c7/0x1510
    [<0000000059068dbc>] ksys_ioctl+0x99/0xb0
    [<000000009a6eb334>] __x64_sys_ioctl+0x78/0xb0
    [<0000000053d0332e>] do_syscall_64+0x16f/0x580
    [<0000000021b83b99>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
    [<000000008ea75434>] 0xffffffffffffffff

Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This code is supposed to test for negative error codes and partial
reads, but because sizeof() is size_t (unsigned) type then negative
error codes are type promoted to high positive values and the condition
doesn't work as expected.

Fixes: 332f989a ("CDC-NCM: handle incomplete transfer of MTU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver/net/can/slcan.c is derived from slip.c. Memory leak was detected
by Syzkaller in slcan. Same issue exists in slip.c and this patch is
addressing the leak in slip.c.

Here is the slcan memory leak trace reported by Syzkaller:

BUG: memory leak unreferenced object 0xffff888067f65500 (size 4096):
  comm "syz-executor043", pid 454, jiffies 4294759719 (age 11.930s)
  hex dump (first 32 bytes):
    73 6c 63 61 6e 30 00 00 00 00 00 00 00 00 00 00 slcan0..........
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
  backtrace:
    [<00000000a06eec0d>] __kmalloc+0x18b/0x2c0
    [<0000000083306e66>] kvmalloc_node+0x3a/0xc0
    [<000000006ac27f87>] alloc_netdev_mqs+0x17a/0x1080
    [<0000000061a996c9>] slcan_open+0x3ae/0x9a0
    [<000000001226f0f9>] tty_ldisc_open.isra.1+0x76/0xc0
    [<0000000019289631>] tty_set_ldisc+0x28c/0x5f0
    [<000000004de5a617>] tty_ioctl+0x48d/0x1590
    [<00000000daef496f>] do_vfs_ioctl+0x1c7/0x1510
    [<0000000059068dbc>] ksys_ioctl+0x99/0xb0
    [<000000009a6eb334>] __x64_sys_ioctl+0x78/0xb0
    [<0000000053d0332e>] do_syscall_64+0x16f/0x580
    [<0000000021b83b99>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
    [<000000008ea75434>] 0xfffffffffffffff

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are the Foxconn-branded variants of the Dell DW5821e modules,
same USB layout as those.

The QMI interface is exposed in USB configuration #1:

P:  Vendor=0489 ProdID=e0b4 Rev=03.18
S:  Manufacturer=FII
S:  Product=T77W968 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.4-20191113' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2019-11-13

this is a pull request of 9 patches for net/master, hopefully for the v5.4
release cycle.

All nine patches are by Oleksij Rempel and fix locking and use-after-free bugs
in the j1939 stack found by the syzkaller syzbot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net): ipsec 2019-11-13

1) Fix a page memleak on xfrm state destroy.

2) Fix a refcount imbalance if a xfrm_state
   gets invaild during async resumption.
   From Xiaodong Xu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

j1939_session_destroy() and __j1939_priv_release() should be called only
if session, ecu or socket are not linked or used by any one else. If at
least one of these resources is linked, then the reference counting is
broken somewhere.

This warning will be triggered before KASAN will do, and will make it
easier to debug initial issue. This works on platforms without KASAN
support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

j1939_can_recv() can be called in parallel with socket release. In this
case sk_release and sk_destruct can be done earlier than
j1939_can_recv() is processed.

Reported-by: syzbot+ca172a0ac477ac90f045@syzkaller.appspotmail.com
Reported-by: syzbot+07ca5bce8530070a5650@syzkaller.appspotmail.com
Reported-by: syzbot+a47537d3964ef6c874e1@syzkaller.appspotmail.com
Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

can: j1939: transport: j1939_cancel_active_session(): use hrtimer_try_to_cancel() instead of hrtimer_cancel()

This part of the code protected by lock used in the hrtimer as well.
Using hrtimer_cancel() will trigger dead lock.

Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

We link the socket to the session to be able provide socket specific
notifications. For example messages over error queue.

We need to keep the socket held, while we have a reference to it.

Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

j1939_session_cancel() was modifying session->state without protecting
it by locks and without checking actual state of the session.

This patch moves j1939_tp_set_rxtimeout() into j1939_session_cancel()
and adds the missing locking.

Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

j1939_sk_sendmsg() should be protected by lock_sock() to avoid race with
j1939_sk_bind() and j1939_sk_release().

Reported-by: syzbot+afd421337a736d6c1ee6@syzkaller.appspotmail.com
Reported-by: syzbot+6d04f6a1b31a0ae12ca9@syzkaller.appspotmail.com
Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

This patch avoids a NULL pointer deref crash if ndev->ml_priv is NULL.

Reported-by: syzbot+95c8e0d9dffde15b6c5c@syzkaller.appspotmail.com
Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

This patch delays the j1939_priv_put() until the socket is destroyed via
the sk_destruct callback, to avoid use-after-free problems.

Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

In j1939 we need our own struct sock::sk_destruct callback. Export the
generic af_can can_sock_destruct() that allows us to chain-call it.

Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

The setup_dpio() function tries to allocate a number of channels equal
to the number of CPUs online. When there are not enough DPCON objects
already probed, the function will return EPROBE_DEFER. When this
happens, the already allocated channels are not freed. This results in
the incapacity of properly probing the next time around.
Fix this by freeing the channels on the error path.

Fixes: d7f5a9d8 ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If an SMC socket is immediately terminated after a non-blocking connect()
has been called, a memory leak is possible.
Due to the sock_hold move in
commit 301428ea ("net/smc: fix refcounting for non-blocking connect()")
an extra sock_put() is needed in smc_connect_work(), if the internal
TCP socket is aborted and cancels the sk_stream_wait_connect() of the
connect worker.

Reported-by: syzbot+4b73ad6fc767e576e275@syzkaller.appspotmail.com
Fixes: 301428ea ("net/smc: fix refcounting for non-blocking connect()")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An ESP packet could be decrypted in async mode if the input handler for
this packet returns -EINPROGRESS in xfrm_input(). At this moment the device
reference in skb is held. Later xfrm_input() will be invoked again to
resume the processing.
If the transform state is still valid it would continue to release the
device reference and there won't be a problem; however if the transform
state is not valid when async resumption happens, the packet will be
dropped while the device reference is still being held.
When the device is deleted for some reason and the reference to this
device is not properly released, the kernel will keep logging like:

unregister_netdevice: waiting for ppp2 to become free. Usage count = 1

The issue is observed when running IPsec traffic over a PPPoE device based
on a bridge interface. By terminating the PPPoE connection on the server
end for multiple times, the PPPoE device on the client side will eventually
get stuck on the above warning message.

This patch will check the async mode first and continue to release device
reference in async resumption, before it is dropped due to invalid state.

v2: Do not assign address family from outer_mode in the transform if the
state is invalid

v3: Release device reference in the error path instead of jumping to resume

Fixes: 4ce3dbe3 ("xfrm: Fix xfrm_input() to verify state is valid when (encap_type < 0)")
Signed-off-by: Xiaodong Xu <stid.smth@gmail.com>
Reported-by: Bo Chen <chenborfc@163.com>
Tested-by: Bo Chen <chenborfc@163.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

Fix coccinelle warning:

./drivers/net/phy/mdio_bus.c:67:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62
./drivers/net/phy/mdio_bus.c:68:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62

Fix this by using IS_ERR before PTR_ERR
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 71dd6c0d ("net: phy: add support for reset-controller")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I2C communication errors (-EREMOTEIO) during the IRQ handler of nxp-nci
result in a NULL pointer dereference at the moment:

    BUG: kernel NULL pointer dereference, address: 0000000000000000
    Oops: 0002 [#1] PREEMPT SMP NOPTI
    CPU: 1 PID: 355 Comm: irq/137-nxp-nci Not tainted 5.4.0-rc6 #1
    RIP: 0010:skb_queue_tail+0x25/0x50
    Call Trace:
     nci_recv_frame+0x36/0x90 [nci]
     nxp_nci_i2c_irq_thread_fn+0xd1/0x285 [nxp_nci_i2c]
     ? preempt_count_add+0x68/0xa0
     ? irq_forced_thread_fn+0x80/0x80
     irq_thread_fn+0x20/0x60
     irq_thread+0xee/0x180
     ? wake_threads_waitq+0x30/0x30
     kthread+0xfb/0x130
     ? irq_thread_check_affinity+0xd0/0xd0
     ? kthread_park+0x90/0x90
     ret_from_fork+0x1f/0x40

Afterward the kernel must be rebooted to work properly again.

This happens because it attempts to call nci_recv_frame() with skb == NULL.
However, unlike nxp_nci_fw_recv_frame(), nci_recv_frame() does not have any
NULL checks for skb, causing the NULL pointer dereference.

Change the code to call only nxp_nci_fw_recv_frame() in case of an error.
Make sure to log it so it is obvious that a communication error occurred.
The error above then becomes:

    nxp-nci_i2c i2c-NXP1001:00: NFC: Read failed with error -121
    nci: __nci_request: wait_for_completion_interruptible_timeout failed 0
    nxp-nci_i2c i2c-NXP1001:00: NFC: Read failed with error -121

Fixes: 6be88670 ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: 5a508a25 ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When setting the dump's time-stamp, use ktime_get_real in addition to
jiffies. This simplifies the user space implementation and bypasses
some inconsistent behavior with translating jiffies to current time.
The time taken is transformed into nsec, to comply with y2038 issue.

Fixes: c8e1da0b ("devlink: Add health report functionality")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!

So let's use the right function (stmmac_pltfr_remove) in the error path.

Fixes: 9f93ac8d ("net-next: stmmac: Add dwmac-sun8i")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes '\n' from trace event class tcp_event_sk_skb to avoid
redundant new blank line and make output compact.

Fixes: af4325ec ("tcp: expose sk_state in tcp_retransmit_skb tracepoint")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:

while true; do
        echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/bind
        devlink dev reload pci/0000:00:10.0 &
        echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/unbind
done

Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bb ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) BPF sample build fixes from Björn Töpel

 2) Fix powerpc bpf tail call implementation, from Eric Dumazet.

 3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.

 4) Fix crash in ebtables when using dnat target, from Florian Westphal.

 5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
    Fainelli.

 6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.

 7) Various KCSAN fixes all over the networking, from Eric Dumazet.

 8) Memory leaks in mlx5 driver, from Alex Vesker.

 9) SMC interface refcounting fix, from Ursula Braun.

10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.

11) Add a TX lock to synchonize the kTLS TX path properly with crypto
    operations. From Jakub Kicinski.

12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
    Garzarella.

13) Infinite loop in Intel ice driver, from Colin Ian King.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
  ixgbe: need_wakeup flag might not be set for Tx
  i40e: need_wakeup flag might not be set for Tx
  igb/igc: use ktime accessors for skb->tstamp
  i40e: Fix for ethtool -m issue on X722 NIC
  iavf: initialize ITRN registers with correct values
  ice: fix potential infinite loop because loop counter being too small
  qede: fix NULL pointer deref in __qede_remove()
  net: fix data-race in neigh_event_send()
  vsock/virtio: fix sock refcnt holding during the shutdown
  net: ethernet: octeon_mgmt: Account for second possible VLAN header
  mac80211: fix station inactive_time shortly after boot
  net/fq_impl: Switch to kvmalloc() for memory allocation
  mac80211: fix ieee80211_txq_setup_flows() failure path
  ipv4: Fix table id reference in fib_sync_down_addr
  ipv6: fixes rt6_probe() and fib6_nh->last_probe init
  net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
  net: usb: qmi_wwan: add support for DW5821e with eSIM support
  CDC-NCM: handle incomplete transfer of MTU
  nfc: netlink: fix double device reference drop
  NFC: st21nfca: fix double free
  ...

Pull block fixes from Jens Axboe:

 - Two NVMe device removal crash fixes, and a compat fixup for for an
   ioctl that was introduced in this release (Anton, Charles, Max - via
   Keith)

 - Missing error path mutex unlock for drbd (Dan)

 - cgroup writeback fixup on dead memcg (Tejun)

 - blkcg online stats print fix (Tejun)

* tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block:
  cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead
  block: drbd: remove a stray unlock in __drbd_send_protocol()
  blkcg: make blkcg_print_stat() print stats only for online blkgs
  nvme: change nvme_passthru_cmd64 to explicitly mark rsvd
  nvme-multipath: fix crash in nvme_mpath_clear_ctrl_paths
  nvme-rdma: fix a segmentation fault during module unload

Jeff Kirsher says:

====================
Intel Wired LAN Driver Fixes 2019-11-08

This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.

Colin Ian King fixes a potentially wrap-around counter in a for-loop.

Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.

Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.

Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.

Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.

This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.

This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.

Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.

Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.

This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC

Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit 92418fb1 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.

Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.

This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255.  Fix this by making i
a u16.

Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>