Some of the RFIM mail box command returns 64 bit values. So enhance
mailbox interface to return 64 bit values and use them for RFIM
commands.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fixes: 5d6fbc96 ("thermal/drivers/int340x: processor_thermal: Export additional attributes")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull thermal control updates from Rafael Wysocki:
 "These extend the thermal trip point crossing notifications sent via
  netlink to contain the temperature causing the trip point to be
  crossed, deprecate the user space thermal governor, add new DT
  bindings to drivers, move ABI documentation to Documentation/ABI, fix
  assorted issues and clean up code.

  Specifics:

   - Constify a variable in thermal MMIO driver (Rikard Falkeborn).

   - Add the current temperature in the netlink message when crossing a
     trip point in order to prevent useless back and forth reading from
     userspace (Daniel Lezcano).

   - Add support for the 'HC' variant on PM8998 PMIC in order to support
     VADC channels on recent QCom boards (Bjorn Andersson).

   - Add support for calibration values from hardware when they are
     fused (Niklas Söderlund).

   - Fix NULL pointer dereference in the thermal_release callback when
     an error occurs in the thermal_zone_device_register() (Yuanzheng
     Song).

   - Fix use-after-free in __thermal_cooling_device_register() in the
     error path (Ziyang Xuan).

   - Fix compilation of the LMh driver when CONFIG_QCOM_SCM is not set
     (Jackie Liu).

   - Add timeout when reading a register that can block forever in
     certain circumstances in the tsens driver (Ansuel Smith).

   - Add DT binding for the reset lines and use them in the rockchip
     sensor driver (Johan Jonker).

   - Add new uniphier NX1 SoC temperature sensor (Kunihiko Hayashi).

   - Save and restore the TCC value in the int340x driver (Antoine
     Tenart).

   - Deprecate the writability of the cooling device state sysfs file
     and the user space governor (Daniel Lezcano).

   - Delete bogus length check in int340x (Dan Carpenter).

   - Use bitmap_zalloc/bitmap_free when applicable in intel_powerclamp
     (Christophe JAILLET).

   - Move thermal ABI documentation to Documentation/ABI (Mauro Carvalho
     Chehab)"

* tag 'thermal-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (21 commits)
  thermal/core: Deprecate changing cooling device state from userspace
  thermal/core: Make the userspace governor deprecated
  thermal/drivers/int340x: Improve the tcc offset saving for suspend/resume
  thermal/drivers/uniphier: Add compatible string for NX1 SoC
  dt-bindings: thermal: uniphier: Add binding for NX1 SoC
  thermal/drivers/rockchip_thermal: Allow more resets for tsadc node
  dt-bindings: thermal: remove redundant comments from rockchip-thermal.yaml
  dt-bindings: thermal: allow more resets for tsadc node in rockchip-thermal.yaml
  thermal/drivers/tsens: Add timeout to get_temp_tsens_valid
  thermal/drivers/qcom/lmh: make QCOM_LMH depends on QCOM_SCM
  thermal/core: fix a UAF bug in __thermal_cooling_device_register()
  thermal/core: Fix null pointer dereference in thermal_release()
  thermal: rcar_gen3_thermal: Read calibration from hardware
  thermal: rcar_gen3_thermal: Store thcode and ptat in priv data
  thermal/drivers/qcom/spmi-adc-tm5: Add support for HC variant
  dt-bindings: thermal: qcom: add HC variant of adc-thermal monitor bindings
  thermal: Move ABI documentation to Documentation/ABI
  thermal/drivers/netlink: Add the temperature when crossing a trip point
  thermal/drivers/thermal_mmio: Constify static struct thermal_mmio_ops
  thermal: int340x: delete bogus length check
  ...

Pull power management updates from Rafael Wysocki:
 "These make the power management of PCI devices with ACPI companions
  more straightforwad, add support for inefficient operating performance
  points to the Energy model and make cpufreq handle them as
  appropriate, rearrange the handling of cpuidle during system PM
  transitions, update a few cpufreq drivers and intel_idle, fix assorded
  issues and clean up code in multiple places.

  Specifics:

   - Add support for inefficient operating performance points to the
     Energy Model and modify cpufreq to use them properly (Vincent
     Donnefort).

   - Rearrange the DTPM framework code to simplify it and make it easier
     to follow (Daniel Lezcano).

   - Fix power intialization in DTPM (Daniel Lezcano).

   - Add CPU load consideration when estimating the instaneous power
     consumption in DTPM (Daniel Lezcano).

   - Fix cpu->pstate.turbo_freq initialization in intel_pstate (Zhang
     Rui).

   - Make intel_pstate process HWP Guaranteed change notifications from
     the processor (Srinivas Pandruvada).

   - Fix typo in cpufreq.h (Rafael Wysocki).

   - Fix tegra driver to handle BPMP errors properly (Mikko Perttunen).

   - Fix the parameter usage of the newly added perf-domain API (Hector
     Yuan).

   - Minor cleanups to cppc, vexpress and s3c244x drivers (Han Wang,
     Guenter Roeck, and Arnd Bergmann).

   - Fix kobject memory leaks in cpuidle error paths (Anel
     Orazgaliyeva).

   - Make intel_idle enable interrupts before entering C1 on some Xeon
     processor models (Artem Bityutskiy).

   - Clean up hib_wait_io() (Falla Coulibaly).

   - Fix sparse warnings in hibernation-related code (Anders Roxell).

   - Use vzalloc() and kzalloc() instead of their open-coded equivalents
     in hibernation-related code (Cai Huoqing).

   - Prevent user space from crashing the kernel by attempting to
     restore the system state from a swap partition in use (Ye Bin).

   - Do not let "syscore" devices runtime-suspend during system PM
     transitions (Rafael Wysocki).

   - Do not pause cpuidle in the suspend-to-idle path (Rafael Wysocki).

   - Pause cpuidle later and resume it earlier during system PM
     transitions (Rafael Wysocki).

   - Make system suspend code use valid_state() consistently (Rafael
     Wysocki).

   - Add support for enabling wakeup IRQs after invoking the
     ->runtime_suspend() callback and make two drivers use it (Chunfeng
     Yun).

   - Make the association of ACPI device objects with PCI devices more
     straightforward and simplify the code doing that for all devices in
     general (Rafael Wysocki).

   - Eliminate struct pci_platform_pm_ops and handle the both of its
     users (PCI and Intel MID) directly in the PCI bus code (Rafael
     Wysocki).

   - Simplify and clarify ACPI PCI device PM helpers (Rafael Wysocki).

   - Fix ordering of operations in pci_back_from_sleep() (Rafael
     Wysocki).

   - Make exynos-ppmu use hyphens in DT properties (Krzysztof
     Kozlowski).

   - Simplify parsing event-type from DT in exynos-ppmu (Krzysztof
     Kozlowski).

   - Strengthen check for freq_table in devfreq (Samuel Holland)"

* tag 'pm-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (49 commits)
  cpufreq: Fix parameter in parse_perf_domain()
  usb: mtu3: enable wake-up interrupt after runtime_suspend called
  usb: xhci-mtk: enable wake-up interrupt after runtime_suspend called
  PM / wakeirq: support enabling wake-up irq after runtime_suspend called
  PM / devfreq: Strengthen check for freq_table
  devfreq: exynos-ppmu: simplify parsing event-type from DT
  devfreq: exynos-ppmu: use node names with hyphens
  cpufreq: intel_pstate: Fix cpu->pstate.turbo_freq initialization
  PM: suspend: Use valid_state() consistently
  PM: sleep: Pause cpuidle later and resume it earlier during system transitions
  PM: suspend: Do not pause cpuidle in the suspend-to-idle path
  PM: sleep: Do not let "syscore" devices runtime-suspend during system transitions
  PM: hibernate: Get block device exclusively in swsusp_check()
  powercap/drivers/dtpm: Fix power limit initialization
  powercap/drivers/dtpm: Scale the power with the load
  powercap/drivers/dtpm: Use container_of instead of a private data field
  powercap/drivers/dtpm: Simplify the dtpm table
  powercap/drivers/dtpm: Encapsulate even more the code
  PM: hibernate: swap: Use vzalloc() and kzalloc()
  PM: hibernate: fix sparse warnings
  ...

Pull ACPI updates from Rafael Wysocki:
 "These update the ACPICA code in the kernel to the most recent upstream
  revision, address some issues related to the ACPI power resources
  management, simplify the enumeration of PCI devices having ACPI
  companions, add new quirks, fix assorted problems, update the
  ACPI-related information in maintainers and clean up code in several
  places.

  Specifics:

   - Update the ACPICA code in the kernel to upstream revision 20210930
     including the following changes:

        - Fix system-wide resume issue caused by evaluating control
          methods too early in the resume path (Rafael Wysocki).

        - Add support for Windows 2020 _OSI string (Mario Limonciello).

        - Add Generic Port Affinity type for SRAT (Alison Schofield).

        - Add disassembly support for the NHLT ACPI table (Bob Moore).

   - Avoid flushing caches before entering C3 type of idle states on AMD
     processors (Deepak Sharma).

   - Avoid enumerating CPUs that are not present and not online-capable
     according to the platform firmware (Mario Limonciello).

   - Add DMI-based mechanism to quirk IRQ overrides and use it for two
     platforms (Hui Wang).

   - Change the configuration of unused ACPI device objects to reflect
     the D3cold power state after enumerating devices (Rafael Wysocki).

   - Update MAINTAINERS information regarding ACPI (Rafael Wysocki).

   - Fix typo in ACPI Kconfig (Masanari Iid).

   - Use sysfs_emit() instead of snprintf() in some places (Qing Wang).

   - Make the association of ACPI device objects with PCI devices more
     straightforward and simplify the code doing that for all devices in
     general (Rafael Wysocki).

   - Use acpi_device_adr() in acpi_find_child_device() instead of
     evaluating _ADR (Rafael Wysocki).

   - Drop duplicate device IDs from PNP device IDs list (Krzysztof
     Kozlowski).

   - Allow acpi_idle_play_dead() to use C3 on AMD processors (Richard
     Gong).

   - Use ACPI_COMPANION() to simplify code in some drivers (Rafael
     Wysocki).

   - Check the states of all ACPI power resources during initialization
     to avoid dealing with power resources in unknown states (Rafael
     Wysocki).

   - Fix ACPI power resource issues related to sharing wakeup power
     resources (Rafael Wysocki).

   - Avoid registering redundant suspend_ops (Rafael Wysocki).

   - Report battery charging state as "full" if it appears to be over
     the design capacity (André Almeida).

   - Quirk GK45 mini PC to skip reading _PSR in the AC driver (Stefan
     Schaeckeler).

   - Mark apei_hest_parse() static (Christoph Hellwig).

   - Relax platform response timeout to 1 second after instructing it to
     inject an error (Shuai Xue).

   - Make the PRM code handle memory allocation and remapping failures
     more gracefully and drop some unnecessary blank lines from that
     code (Aubrey Li).

   - Fix spelling mistake in the ACPI documentation (Colin Ian King)"

* tag 'acpi-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (36 commits)
  ACPI: glue: Use acpi_device_adr() in acpi_find_child_device()
  perf: qcom_l2_pmu: ACPI: Use ACPI_COMPANION() directly
  ACPI: APEI: mark apei_hest_parse() static
  ACPI: APEI: EINJ: Relax platform response timeout to 1 second
  gpio-amdpt: ACPI: Use the ACPI_COMPANION() macro directly
  nouveau: ACPI: Use the ACPI_COMPANION() macro directly
  ACPI: resources: Add one more Medion model in IRQ override quirk
  ACPI: AC: Quirk GK45 to skip reading _PSR
  ACPI: PM: sleep: Do not set suspend_ops unnecessarily
  ACPI: PRM: Handle memory allocation and memory remap failure
  ACPI: PRM: Remove unnecessary blank lines
  ACPI: PM: Turn off wakeup power resources on _DSW/_PSW errors
  ACPI: PM: Fix sharing of wakeup power resources
  ACPI: PM: Turn off unused wakeup power resources
  ACPI: PM: Check states of power resources during initialization
  ACPI: replace snprintf() in "show" functions with sysfs_emit()
  ACPI: LPSS: Use ACPI_COMPANION() directly
  ACPI: scan: Release PM resources blocked by unused objects
  ACPI: battery: Accept charges over the design capacity as full
  ACPICA: Update version to 20210930
  ...

Merge branch 'ucount-fixes-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace

Pull ucount cleanups from Eric Biederman:
 "While working on the ucount fixes a for v5.15 a number of cleanups
  suggested themselves.

  Little things like not testing for NULL when a pointer can not be NULL
  and wrapping atomic_add_negative with a more descriptive name, so that
  people reading the code can more quickly understand what is going on"

* 'ucount-fixes-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  ucounts: Use atomic_long_sub_return for clarity
  ucounts: Add get_ucounts_or_wrap for clarity
  ucounts: Remove unnecessary test for NULL ucount in get_ucounts
  ucounts: In set_cred_ucounts assume new->ucounts is non-NULL

Pull cgroup updates from Tejun Heo:

 - The misc controller now reports allocation rejections through
   misc.events instead of printking

 - cgroup_mutex usage is reduced to improve scalability of some
   operations

 - vhost helper threads are now assigned to the right cgroup on cgroup2

 - Bug fixes

* 'for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: bpf: Move wrapper for __cgroup_bpf_*() to kernel/bpf/cgroup.c
  cgroup: Fix rootcg cpu.stat guest double counting
  cgroup: no need for cgroup_mutex for /proc/cgroups
  cgroup: remove cgroup_mutex from cgroupstats_build
  cgroup: reduce dependency on cgroup_mutex
  cgroup: cgroup-v1: do not exclude cgrp_dfl_root
  cgroup: Make rebind_subsystems() disable v2 controllers all at once
  docs/cgroup: add entry for misc.events
  misc_cgroup: remove error log to avoid log flood
  misc_cgroup: introduce misc.events to count failures

Pull workqueue updates from Tejun Heo:
 "Nothing too interesting. An optimization to short-circuit noop cpumask
  updates, debug dump code reorg, and doc update"

* 'for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: doc: Call out the non-reentrance conditions
  workqueue: Introduce show_one_worker_pool and show_one_workqueue.
  workqueue: make sysfs of unbound kworker cpumask more clever

Pull xfs updates from Darrick Wong:
 "This cycle we've worked on fixing bugs and improving XFS' memory
  footprint.

  The most notable fixes include: fixing a corruption warning (and free
  space accounting skew) if copy on write fails; fixing slab cache
  misuse if SLOB is enabled, which apparently was broken for years
  without anybody noticing; and fixing a potential race with online
  shrinkfs.

  Otherwise, the bulk of the changes here involve setting up separate
  slab caches for frequently used items such as btree cursors and log
  intent items, and compacting the structures to reduce memory usage of
  those items substantially. This also sets us up to support larger
  btrees in future kernels. We also switch parts of online fsck to
  allocate scrub context information from the heap instead of using
  stack space.

  Summary:

   - Bug fixes and cleanups for kernel memory allocation usage, this
     time without touching the mm code.

   - Refactor the log recovery mechanism that preserves held resources
     across a transaction roll so that it uses the exact same mechanism
     that we use for that during regular runtime.

   - Fix bugs and tighten checking around btree heights.

   - Remove more old typedefs.

   - Fix perag reference leaks when racing with growfs.

   - Remove unused fields from xfs_btree_cur.

   - Allocate various scrub structures on the heap to reduce stack
     usage.

   - Pack xfs_btree_cur fields and rearrange to support arbitrary
     heights.

   - Compute maximum possible heights for each btree height, and use
     that to set up slab caches for each btree type.

   - Finally remove kmem_zone_t, since these have always been struct
     kmem_cache on Linux.

   - Compact the structures used to coordinate work intent items.

   - Set up slab caches for each work intent item type.

   - Rename the "bmap_add_free" function to "free_extent_later", which
     more accurately describes what it does.

   - Fix corruption warning on unmount when a CoW preallocation covers a
     data fork delalloc reservation but then the CoW fails.

   - Add some more minor code improvements"

* tag 'xfs-5.16-merge-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (45 commits)
  xfs: use swap() to make code cleaner
  xfs: Remove duplicated include in xfs_super
  xfs: punch out data fork delalloc blocks on COW writeback failure
  xfs: remove unused parameter from refcount code
  xfs: reduce the size of struct xfs_extent_free_item
  xfs: rename xfs_bmap_add_free to xfs_free_extent_later
  xfs: create slab caches for frequently-used deferred items
  xfs: compact deferred intent item structures
  xfs: rename _zone variables to _cache
  xfs: remove kmem_zone typedef
  xfs: use separate btree cursor cache for each btree type
  xfs: compute absolute maximum nlevels for each btree type
  xfs: kill XFS_BTREE_MAXLEVELS
  xfs: compute the maximum height of the rmap btree when reflink enabled
  xfs: clean up xfs_btree_{calc_size,compute_maxlevels}
  xfs: compute maximum AG btree height for critical reservation calculation
  xfs: rename m_ag_maxlevels to m_allocbt_maxlevels
  xfs: dynamically allocate cursors based on maxlevels
  xfs: encode the max btree height in the cursor
  xfs: refactor btree cursor allocation function
  ...

Pull AFS updates from David Howells:

 - Split the readpage handler for symlinks from the one for files. The
   symlink readpage isn't given a file pointer, so the handling has to
   be special-cased.

   This has been posted as part of a patchset to foliate netfs, afs,
   etc.[1] but I've moved it to this one as it's not actually doing
   foliation but is more of a pre-cleanup.

 - Fix file creation to set the mtime from the client's clock to keep
   make happy if the server's clock isn't quite in sync.[2]

Link: https://lore.kernel.org/r/163005742570.2472992.7800423440314043178.stgit@warthog.procyon.org.uk/ [1]
Link: http://lists.infradead.org/pipermail/linux-afs/2021-October/004395.html [2]

* tag 'afs-next-20211102' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: Set mtime from the client for yfs create operations
  afs: Sort out symlink reading

Pull gfs2 updates from Andreas Gruenbacher:

 - Fix a locking order inversion between the inode and iopen glocks in
   gfs2_inode_lookup.

 - Implement proper queuing of glock holders for glocks that require
   instantiation (like reading an inode or bitmap blocks from disk).
   Before, multiple glock holders could race with each other and
   half-initialized objects could be exposed; the GL_SKIP flag further
   exacerbated this problem.

 - Fix a rare deadlock between inode lookup / creation and remote delete
   work.

 - Fix a rare scheduling-while-atomic bug in dlm during glock hash table
   walks.

 - Various other minor fixes and cleanups.

* tag 'gfs2-v5.15-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2: (21 commits)
  gfs2: Fix unused value warning in do_gfs2_set_flags()
  gfs2: check context in gfs2_glock_put
  gfs2: Fix glock_hash_walk bugs
  gfs2: Cancel remote delete work asynchronously
  gfs2: set glock object after nq
  gfs2: remove RDF_UPTODATE flag
  gfs2: Eliminate GIF_INVALID flag
  gfs2: fix GL_SKIP node_scope problems
  gfs2: split glock instantiation off from do_promote
  gfs2: further simplify do_promote
  gfs2: re-factor function do_promote
  gfs2: Remove 'first' trace_gfs2_promote argument
  gfs2: change go_lock to go_instantiate
  gfs2: dump glocks from gfs2_consist_OBJ_i
  gfs2: dequeue iopen holder in gfs2_inode_lookup error
  gfs2: Save ip from gfs2_glock_nq_init
  gfs2: Allow append and immutable bits to coexist
  gfs2: Switch some BUG_ON to GLOCK_BUG_ON for debug
  gfs2: move GL_SKIP check from glops to do_promote
  gfs2: Add GL_SKIP holder flag to dump_holder
  ...

Merge tag 'gfs2-v5.15-rc5-mmap-fault' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2

Pull gfs2 mmap + page fault deadlocks fixes from Andreas Gruenbacher:
 "Functions gfs2_file_read_iter and gfs2_file_write_iter are both
  accessing the user buffer to write to or read from while holding the
  inode glock.

  In the most basic deadlock scenario, that buffer will not be resident
  and it will be mapped to the same file. Accessing the buffer will
  trigger a page fault, and gfs2 will deadlock trying to take the same
  inode glock again while trying to handle that fault.

  Fix that and similar, more complex scenarios by disabling page faults
  while accessing user buffers. To make this work, introduce a small
  amount of new infrastructure and fix some bugs that didn't trigger so
  far, with page faults enabled"

* tag 'gfs2-v5.15-rc5-mmap-fault' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  gfs2: Fix mmap + page fault deadlocks for direct I/O
  iov_iter: Introduce nofault flag to disable page faults
  gup: Introduce FOLL_NOFAULT flag to disable page faults
  iomap: Add done_before argument to iomap_dio_rw
  iomap: Support partial direct I/O on user copy failures
  iomap: Fix iomap_dio_rw return value for user copies
  gfs2: Fix mmap + page fault deadlocks for buffered I/O
  gfs2: Eliminate ip->i_gh
  gfs2: Move the inode glock locking to gfs2_file_buffered_write
  gfs2: Introduce flag for glock holder auto-demotion
  gfs2: Clean up function may_grant
  gfs2: Add wrapper for iomap_file_buffered_write
  iov_iter: Introduce fault_in_iov_iter_writeable
  iov_iter: Turn iov_iter_fault_in_readable into fault_in_iov_iter_readable
  gup: Turn fault_in_pages_{readable,writeable} into fault_in_{readable,writeable}
  powerpc/kvm: Fix kvm_use_magic_page
  iov_iter: Fix iov_iter_get_pages{,_alloc} page fault return value

Pull ARM updates from Russell King:

 - Rejig task/thread info to place thread info in task struct

 - Amba bus cleanups (removing unused functions)

 - Handle Amba device probe without IRQ domains

 - Parse linux,usable-memory-range in decompressor

 - Mark OCRAM as read-only after initialisation

 - Refactor page fault handling

 - Fix PXN handling with LPAE kernels

 - Warning and build fixes from Arnd

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (32 commits)
  ARM: 9151/1: Thumb2: avoid __builtin_thread_pointer() on Clang
  ARM: 9150/1: Fix PID_IN_CONTEXTIDR regression when THREAD_INFO_IN_TASK=y
  ARM: 9147/1: add printf format attribute to early_print()
  ARM: 9146/1: RiscPC needs older gcc version
  ARM: 9145/1: patch: fix BE32 compilation
  ARM: 9144/1: forbid ftrace with clang and thumb2_kernel
  ARM: 9143/1: add CONFIG_PHYS_OFFSET default values
  ARM: 9142/1: kasan: work around LPAE build warning
  ARM: 9140/1: allow compile-testing without machine record
  ARM: 9137/1: disallow CONFIG_THUMB with ARMv4
  ARM: 9136/1: ARMv7-M uses BE-8, not BE-32
  ARM: 9135/1: kprobes: address gcc -Wempty-body warning
  ARM: 9101/1: sa1100/assabet: convert LEDs to gpiod APIs
  ARM: 9131/1: mm: Fix PXN process with LPAE feature
  ARM: 9130/1: mm: Provide die_kernel_fault() helper
  ARM: 9126/1: mm: Kill page table base print in show_pte()
  ARM: 9127/1: mm: Cleanup access_error()
  ARM: 9129/1: mm: Kill task_struct argument for __do_page_fault()
  ARM: 9128/1: mm: Refactor the __do_page_fault()
  ARM: imx6: mark OCRAM mapping read-only
  ...

Merge Energy Model and power capping updates for 5.16-rc1:

 - Add support for inefficient operating performance points to the
   Energy Model and modify cpufreq to use them properly (Vincent
   Donnefort).

 - Rearrange the DTPM framework code to simplify it and make it easier
   to follow (Daniel Lezcano).

 - Fix power intialization in DTPM (Daniel Lezcano).

 - Add CPU load consideration when estimating the instaneous power
   consumption in DTPM (Daniel Lezcano).

* pm-em:
  cpufreq: mediatek-hw: Fix cpufreq_table_find_index_dl() call
  PM: EM: Mark inefficiencies in CPUFreq
  cpufreq: Use CPUFREQ_RELATION_E in DVFS governors
  cpufreq: Introducing CPUFREQ_RELATION_E
  cpufreq: Add an interface to mark inefficient frequencies
  cpufreq: Make policy min/max hard requirements
  PM: EM: Allow skipping inefficient states
  PM: EM: Extend em_perf_domain with a flag field
  PM: EM: Mark inefficient states
  PM: EM: Fix inefficient states detection

* powercap:
  powercap/drivers/dtpm: Fix power limit initialization
  powercap/drivers/dtpm: Scale the power with the load
  powercap/drivers/dtpm: Use container_of instead of a private data field
  powercap/drivers/dtpm: Simplify the dtpm table
  powercap/drivers/dtpm: Encapsulate even more the code

Pull KVM updates from Paolo Bonzini:
 "ARM:

   - More progress on the protected VM front, now with the full fixed
     feature set as well as the limitation of some hypercalls after
     initialisation.

   - Cleanup of the RAZ/WI sysreg handling, which was pointlessly
     complicated

   - Fixes for the vgic placement in the IPA space, together with a
     bunch of selftests

   - More memcg accounting of the memory allocated on behalf of a guest

   - Timer and vgic selftests

   - Workarounds for the Apple M1 broken vgic implementation

   - KConfig cleanups

   - New kvmarm.mode=none option, for those who really dislike us

  RISC-V:

   - New KVM port.

  x86:

   - New API to control TSC offset from userspace

   - TSC scaling for nested hypervisors on SVM

   - Switch masterclock protection from raw_spin_lock to seqcount

   - Clean up function prototypes in the page fault code and avoid
     repeated memslot lookups

   - Convey the exit reason to userspace on emulation failure

   - Configure time between NX page recovery iterations

   - Expose Predictive Store Forwarding Disable CPUID leaf

   - Allocate page tracking data structures lazily (if the i915 KVM-GT
     functionality is not compiled in)

   - Cleanups, fixes and optimizations for the shadow MMU code

  s390:

   - SIGP Fixes

   - initial preparations for lazy destroy of secure VMs

   - storage key improvements/fixes

   - Log the guest CPNC

  Starting from this release, KVM-PPC patches will come from Michael
  Ellerman's PPC tree"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (227 commits)
  RISC-V: KVM: fix boolreturn.cocci warnings
  RISC-V: KVM: remove unneeded semicolon
  RISC-V: KVM: Fix GPA passed to __kvm_riscv_hfence_gvma_xyz() functions
  RISC-V: KVM: Factor-out FP virtualization into separate sources
  KVM: s390: add debug statement for diag 318 CPNC data
  KVM: s390: pv: properly handle page flags for protected guests
  KVM: s390: Fix handle_sske page fault handling
  KVM: x86: SGX must obey the KVM_INTERNAL_ERROR_EMULATION protocol
  KVM: x86: On emulation failure, convey the exit reason, etc. to userspace
  KVM: x86: Get exit_reason as part of kvm_x86_ops.get_exit_info
  KVM: x86: Clarify the kvm_run.emulation_failure structure layout
  KVM: s390: Add a routine for setting userspace CPU state
  KVM: s390: Simplify SIGP Set Arch handling
  KVM: s390: pv: avoid stalls when making pages secure
  KVM: s390: pv: avoid stalls for kvm_s390_pv_init_vm
  KVM: s390: pv: avoid double free of sida page
  KVM: s390: pv: add macros for UVC CC values
  s390/mm: optimize reset_guest_reference_bit()
  s390/mm: optimize set_guest_storage_key()
  s390/mm: no need for pte_alloc_map_lock() if we know the pmd is present
  ...

Merge cpufreq and cpuidle updates for 5.16-rc1:

 - Fix cpu->pstate.turbo_freq initialization in intel_pstate (Zhang
   Rui).

 - Make intel_pstate process HWP Guaranteed change notifications from
   the processor (Srinivas Pandruvada).

 - Fix typo in cpufreq.h (Rafael Wysocki).

 - Fix tegra driver to handle BPMP errors properly (Mikko Perttunen).

 - Fix the parameter usage of the newly added perf-domain API (Hector
   Yuan).

 - Minor cleanups to cppc, vexpress and s3c244x drivers (Han Wang,
   Guenter Roeck, and Arnd Bergmann).

 - Fix kobject memory leaks in cpuidle error paths (Anel Orazgaliyeva).

 - Make intel_idle enable interrupts before entering C1 on some Xeon
   processor models (Artem Bityutskiy).

* pm-cpufreq:
  cpufreq: Fix parameter in parse_perf_domain()
  cpufreq: intel_pstate: Fix cpu->pstate.turbo_freq initialization
  cpufreq: Fix typo in cpufreq.h
  cpufreq: intel_pstate: Process HWP Guaranteed change notification
  cpufreq: tegra186/tegra194: Handle errors in BPMP response
  cpufreq: remove useless INIT_LIST_HEAD()
  cpufreq: s3c244x: add fallthrough comments for switch
  cpufreq: vexpress: Drop unused variable

* pm-cpuidle:
  cpuidle: Fix kobject memory leaks in error paths
  intel_idle: enable interrupts before C1 on Xeons

Merge updates related to system sleep for 5.16-rc1:

 - Clean up hib_wait_io() (Falla Coulibaly).

 - Fix sparse warnings in hibernation-related code (Anders Roxell).

 - Use vzalloc() and kzalloc() instead of their open-coded
   equivalents in hibernation-related code (Cai Huoqing).

 - Prevent user space from crashing the kernel by attempting to
   restore the system state from a swap partition in use (Ye Bin).

 - Do not let "syscore" devices runtime-suspend during system PM
   transitions (Rafael Wysocki).

 - Do not pause cpuidle in the suspend-to-idle path (Rafael Wysocki).

 - Pause cpuidle later and resume it earlier during system PM
   transitions (Rafael Wysocki).

 - Make system suspend code use valid_state() consistently (Rafael
   Wysocki).

 - Add support for enabling wakeup IRQs after invoking the
   ->runtime_suspend() callback and make two drivers use it (Chunfeng
   Yun).

* pm-sleep:
  usb: mtu3: enable wake-up interrupt after runtime_suspend called
  usb: xhci-mtk: enable wake-up interrupt after runtime_suspend called
  PM / wakeirq: support enabling wake-up irq after runtime_suspend called
  PM: suspend: Use valid_state() consistently
  PM: sleep: Pause cpuidle later and resume it earlier during system transitions
  PM: suspend: Do not pause cpuidle in the suspend-to-idle path
  PM: sleep: Do not let "syscore" devices runtime-suspend during system transitions
  PM: hibernate: Get block device exclusively in swsusp_check()
  PM: hibernate: swap: Use vzalloc() and kzalloc()
  PM: hibernate: fix sparse warnings
  Revert "PM: sleep: Do not assume that "mem" is always present"
  PM: hibernate: Remove blk_status_to_errno in hib_wait_io
  PM: sleep: Do not assume that "mem" is always present

Merge PCI device power management updates for 5.16-rc1:

 - Make the association of ACPI device objects with PCI devices more
   straightforward and simplify the code doing that for all devices
   in general (Rafael Wysocki).

 - Eliminate struct pci_platform_pm_ops and handle the both of its
   users (PCI and Intel MID) directly in the PCI bus code (Rafael
   Wysocki).

 - Simplify and clarify ACPI PCI device PM helpers (Rafael Wysocki).

 - Fix ordering of operations in pci_back_from_sleep() (Rafael
   Wysocki).

* pm-pci:
  PCI: PM: Fix ordering of operations in pci_back_from_sleep()
  PCI: PM: Do not call platform_pci_power_manageable() unnecessarily
  PCI: PM: Make pci_choose_state() call pci_target_state()
  PCI: PM: Rearrange pci_target_state()
  PCI: PM: Simplify acpi_pci_power_manageable()
  PCI: PM: Drop struct pci_platform_pm_ops
  PCI: ACPI: PM: Do not use pci_platform_pm_ops for ACPI
  PCI: PM: Do not use pci_platform_pm_ops for Intel MID PM
  ACPI: glue: Look for ACPI bus type only if ACPI companion is not known
  ACPI: glue: Drop cleanup callback from struct acpi_bus_type
  PCI: ACPI: Drop acpi_pci_bus

Merge APEI, PRM and documentation udpates for 5.16-rc1:

 - Mark apei_hest_parse() static (Christoph Hellwig).

 - Relax platform response timeout to 1 second after instructing it
   to inject an error (Shuai Xue).

 - Make the PRM code handle memory allocation and remapping failures
   more gracefully and drop some unnecessary blank lines from that
   code (Aubrey Li).

 - Fix spelling mistake in the ACPI documentation (Colin Ian King).

* acpi-apei:
  ACPI: APEI: mark apei_hest_parse() static
  ACPI: APEI: EINJ: Relax platform response timeout to 1 second

* acpi-prm:
  ACPI: PRM: Handle memory allocation and memory remap failure
  ACPI: PRM: Remove unnecessary blank lines

* acpi-docs:
  Documentation: ACPI: Fix spelling mistake "Millenium" -> "Millennium"

Merge tag 'hyperv-next-signed-20211102' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux

Pull hyperv updates from Wei Liu:

 - Initial patch set for Hyper-V isolation VM support (Tianyu Lan)

 - Fix a warning on preemption (Vitaly Kuznetsov)

 - A bunch of misc cleanup patches

* tag 'hyperv-next-signed-20211102' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
  x86/hyperv: Protect set_hv_tscchange_cb() against getting preempted
  Drivers: hv : vmbus: Adding NULL pointer check
  x86/hyperv: Remove duplicate include
  x86/hyperv: Remove duplicated include in hv_init
  Drivers: hv: vmbus: Remove unused code to check for subchannels
  Drivers: hv: vmbus: Initialize VMbus ring buffer for Isolation VM
  Drivers: hv: vmbus: Add SNP support for VMbus channel initiate message
  x86/hyperv: Add ghcb hvcall support for SNP VM
  x86/hyperv: Add Write/Read MSR registers via ghcb page
  Drivers: hv: vmbus: Mark vmbus ring buffer visible to host in Isolation VM
  x86/hyperv: Add new hvcall guest address host visibility support
  x86/hyperv: Initialize shared memory boundary in the Isolation VM.
  x86/hyperv: Initialize GHCB page in Isolation VM

Pull printk updates from Petr Mladek:

 - Extend %pGp print format to print hex value of the page flags

 - Use kvmalloc instead of kmalloc to allocate devkmsg buffers

 - Misc cleanup and warning fixes

* tag 'printk-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
  vsprintf: Update %pGp documentation about that it prints hex value
  lib/vsprintf.c: Amend static asserts for format specifier flags
  vsprintf: Make %pGp print the hex value
  test_printf: Append strings more efficiently
  test_printf: Remove custom appending of '|'
  test_printf: Remove separate page_flags variable
  test_printf: Make pft array const
  ia64: don't do IA64_CMPXCHG_DEBUG without CONFIG_PRINTK
  printk: use gnu_printf format attribute for printk_sprint()
  printk: avoid -Wsometimes-uninitialized warning
  printk: use kvmalloc instead of kmalloc for devkmsg_user

Pull integrity subsystem updates from Mimi Zohar:
 "Other than the new gid IMA policy rule support and the RCU locking
  fix, the couple of remaining changes are minor/trivial (e.g.
  __ro_after_init, replacing strscpy)"

* tag 'integrity-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
  evm: mark evm_fixmode as __ro_after_init
  ima: Use strscpy instead of strlcpy
  ima_policy: Remove duplicate 'the' in docs comment
  ima: add gid support
  ima: fix uid code style problems
  ima: fix deadlock when traversing "ima_default_rules".

Merge updates related to device power management, system sleep,
battery driver and AC driver for 5.16-rc1:

 - Check the states of all ACPI power resources during initialization
   to avoid dealing with power resources in unknown states (Rafael
   Wysocki).

 - Fix ACPI power resource issues related to sharing wakeup power
   resources (Rafael Wysocki).

 - Avoid registering redundant suspend_ops (Rafael Wysocki).

 - Report battery charging state as "full" if it appears to be over
   the design capacity (André Almeida).

 - Quirk GK45 mini PC to skip reading _PSR in the AC driver (Stefan
   Schaeckeler).

* acpi-pm:
  ACPI: PM: sleep: Do not set suspend_ops unnecessarily
  ACPI: PM: Turn off wakeup power resources on _DSW/_PSW errors
  ACPI: PM: Fix sharing of wakeup power resources
  ACPI: PM: Turn off unused wakeup power resources
  ACPI: PM: Check states of power resources during initialization

* acpi-battery:
  ACPI: battery: Accept charges over the design capacity as full

* acpi-ac:
  ACPI: AC: Quirk GK45 to skip reading _PSR

Pull libata updates from Damien Le Moal:

 - Remove duplicated AHCI adapter PCI device IDs (from Krzysztof)

 - Cleanup of device DMA state checking to consistantly use
   ata_dma_enabled() (from Reimar)

* tag 'libata-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
  pata_radisys: fix checking of DMA state
  pata_optidma: fix checking of DMA state
  pata_amd: fix checking of DMA state
  pata_ali: fix checking of DMA state
  libata-scsi: fix checking of DMA state
  libata: fix checking of DMA state
  Add AHCI support for ASM1062+JBM575 cards
  ahci: remove duplicated PCI device IDs

Merge updates of the code associating ACPI device objects with
devices and PNP code, processor driver, and Intel LPSS driver updates
for 5.16-rc1:

 - Make the association of ACPI device objects with PCI devices more
   straightforward and simplify the code doing that for all devices
   in general (Rafael Wysocki).

 - Use acpi_device_adr() in acpi_find_child_device() instead of
   evaluating _ADR (Rafael Wysocki).

 - Drop duplicate device IDs from PNP device IDs list (Krzysztof
   Kozlowski).

 - Allow acpi_idle_play_dead() to use C3 on AMD processors (Richard
   Gong).

 - Use ACPI_COMPANION() to simplify code in the ACPI driver for Intel
   SoCs (Rafael Wysocki).

* acpi-glue:
  ACPI: glue: Use acpi_device_adr() in acpi_find_child_device()
  ACPI: glue: Look for ACPI bus type only if ACPI companion is not known
  ACPI: glue: Drop cleanup callback from struct acpi_bus_type
  PCI: ACPI: Drop acpi_pci_bus

* acpi-pnp:
  ACPI: PNP: remove duplicated BRI0A49 and BDP3336 entries

* acpi-processor:
  ACPI: processor idle: Allow playing dead in C3 state

* acpi-soc:
  ACPI: LPSS: Use ACPI_COMPANION() directly

Merge x86-specific ACPI updates, ACPI resources management updates,
one ACPI device enumeration update and miscellaneous ACPI updates for
5.16-rc1:

 - Avoid flushing caches before entering C3 type of idle states on
   AMD processors (Deepak Sharma).

 - Avoid enumerating CPUs that are not present and not online-capable
   according to the platform firmware (Mario Limonciello).

 - Add DMI-based mechanism to quirk IRQ overrides and use it for two
   platforms (Hui Wang).

 - Change the configuration of unused ACPI device objects to reflect
   the D3cold power state after enumerating devices (Rafael Wysocki).

 - Update MAINTAINERS information regarding ACPI (Rafael Wysocki).

 - Fix typo in ACPI Kconfig (Masanari Iid).

 - Use sysfs_emit() instead of snprintf() in some places (Qing Wang).

* acpi-x86:
  x86: ACPI: cstate: Optimize C3 entry on AMD CPUs
  x86/ACPI: Don't add CPUs that are not online capable
  ACPICA: Add support for MADT online enabled bit

* acpi-resources:
  ACPI: resources: Add one more Medion model in IRQ override quirk
  ACPI: resources: Add DMI-based legacy IRQ override quirk

* acpi-scan:
  ACPI: scan: Release PM resources blocked by unused objects

* acpi-misc:
  ACPI: replace snprintf() in "show" functions with sysfs_emit()
  ACPI: Update information in MAINTAINERS
  ACPI: Kconfig: Fix a typo in Kconfig

Merge ACPICA updates for 5.16-rc1:

 - Fix system-wide resume issue caused by evaluating control methods
   too early in the resume path (Rafael Wysocki).

 - Add support for Windows 2020 _OSI string (Mario Limonciello).

 - Add Generic Port Affinity type for SRAT (Alison Schofield).

 - Add disassembly support for the NHLT ACPI table (Bob Moore).

* acpica:
  ACPICA: Update version to 20210930
  ACPICA: iASL table disassembler: Added disassembly support for the NHLT ACPI table
  ACPICA: ACPI 6.4 SRAT: add Generic Port Affinity type
  ACPICA: Add support for Windows 2020 _OSI string
  ACPICA: Avoid evaluating methods too early during system resume

Pull ARM cpufreq updates for 5.16-rc1 from Viresh Kumar:

"- Fix tegra driver to handle BPMP errors properly (Mikko Perttunen).

 - Fix the parameter usage of the newly added perf-domain API (Hector
   Yuan).

 - Minor cleanups to cppc, vexpress and s3c244x drivers (Han Wang,
   Guenter Roeck, and Arnd Bergmann)."

* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
  cpufreq: Fix parameter in parse_perf_domain()
  cpufreq: tegra186/tegra194: Handle errors in BPMP response
  cpufreq: remove useless INIT_LIST_HEAD()
  cpufreq: s3c244x: add fallthrough comments for switch
  cpufreq: vexpress: Drop unused variable

Pull x86 core updates from Borislav Petkov:

 - Do not #GP on userspace use of CLI/STI but pretend it was a NOP to
   keep old userspace from breaking. Adjust the corresponding iopl
   selftest to that.

 - Improve stack overflow warnings to say which stack got overflowed and
   raise the exception stack sizes to 2 pages since overflowing the
   single page of exception stack is very easy to do nowadays with all
   the tracing machinery enabled. With that, rip out the custom mapping
   of AMD SEV's too.

 - A bunch of changes in preparation for FGKASLR like supporting more
   than 64K section headers in the relocs tool, correct ORC lookup table
   size to cover the whole kernel .text and other adjustments.

* tag 'x86_core_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/x86/iopl: Adjust to the faked iopl CLI/STI usage
  vmlinux.lds.h: Have ORC lookup cover entire _etext - _stext
  x86/boot/compressed: Avoid duplicate malloc() implementations
  x86/boot: Allow a "silent" kaslr random byte fetch
  x86/tools/relocs: Support >64K section headers
  x86/sev: Make the #VC exception stacks part of the default stacks storage
  x86: Increase exception stack sizes
  x86/mm/64: Improve stack overflow warnings
  x86/iopl: Fake iopl(3) CLI/STI usage

Pull networking updates from Jakub Kicinski:
 "Core:

   - Remove socket skb caches

   - Add a SO_RESERVE_MEM socket op to forward allocate buffer space and
     avoid memory accounting overhead on each message sent

   - Introduce managed neighbor entries - added by control plane and
     resolved by the kernel for use in acceleration paths (BPF / XDP
     right now, HW offload users will benefit as well)

   - Make neighbor eviction on link down controllable by userspace to
     work around WiFi networks with bad roaming implementations

   - vrf: Rework interaction with netfilter/conntrack

   - fq_codel: implement L4S style ce_threshold_ect1 marking

   - sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()

  BPF:

   - Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
     as implemented in LLVM14

   - Introduce bpf_get_branch_snapshot() to capture Last Branch Records

   - Implement variadic trace_printk helper

   - Add a new Bloomfilter map type

   - Track <8-byte scalar spill and refill

   - Access hw timestamp through BPF's __sk_buff

   - Disallow unprivileged BPF by default

   - Document BPF licensing

  Netfilter:

   - Introduce egress hook for looking at raw outgoing packets

   - Allow matching on and modifying inner headers / payload data

   - Add NFT_META_IFTYPE to match on the interface type either from
     ingress or egress

  Protocols:

   - Multi-Path TCP:
      - increase default max additional subflows to 2
      - rework forward memory allocation
      - add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS

   - MCTP flow support allowing lower layer drivers to configure msg
     muxing as needed

   - Automatic Multicast Tunneling (AMT) driver based on RFC7450

   - HSR support the redbox supervision frames (IEC-62439-3:2018)

   - Support for the ip6ip6 encapsulation of IOAM

   - Netlink interface for CAN-FD's Transmitter Delay Compensation

   - Support SMC-Rv2 eliminating the current same-subnet restriction, by
     exploiting the UDP encapsulation feature of RoCE adapters

   - TLS: add SM4 GCM/CCM crypto support

   - Bluetooth: initial support for link quality and audio/codec offload

  Driver APIs:

   - Add a batched interface for RX buffer allocation in AF_XDP buffer
     pool

   - ethtool: Add ability to control transceiver modules' power mode

   - phy: Introduce supported interfaces bitmap to express MAC
     capabilities and simplify PHY code

   - Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks

  New drivers:

   - WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)

   - Ethernet driver for ASIX AX88796C SPI device (x88796c)

  Drivers:

   - Broadcom PHYs
      - support 72165, 7712 16nm PHYs
      - support IDDQ-SR for additional power savings

   - PHY support for QCA8081, QCA9561 PHYs

   - NXP DPAA2: support for IRQ coalescing

   - NXP Ethernet (enetc): support for software TCP segmentation

   - Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
     Gigabit-capable IP found on RZ/G2L SoC

   - Intel 100G Ethernet
      - support for eswitch offload of TC/OvS flow API, including
        offload of GRE, VxLAN, Geneve tunneling
      - support application device queues - ability to assign Rx and Tx
        queues to application threads
      - PTP and PPS (pulse-per-second) extensions

   - Broadcom Ethernet (bnxt)
      - devlink health reporting and device reload extensions

   - Mellanox Ethernet (mlx5)
      - offload macvlan interfaces
      - support HW offload of TC rules involving OVS internal ports
      - support HW-GRO and header/data split
      - support application device queues

   - Marvell OcteonTx2:
      - add XDP support for PF
      - add PTP support for VF

   - Qualcomm Ethernet switch (qca8k): support for QCA8328

   - Realtek Ethernet DSA switch (rtl8366rb)
      - support bridge offload
      - support STP, fast aging, disabling address learning
      - support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch

   - Mellanox Ethernet/IB switch (mlxsw)
      - multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
      - offload root TBF qdisc as port shaper
      - support multiple routing interface MAC address prefixes
      - support for IP-in-IP with IPv6 underlay

   - MediaTek WiFi (mt76)
      - mt7921 - ASPM, 6GHz, SDIO and testmode support
      - mt7915 - LED and TWT support

   - Qualcomm WiFi (ath11k)
      - include channel rx and tx time in survey dump statistics
      - support for 80P80 and 160 MHz bandwidths
      - support channel 2 in 6 GHz band
      - spectral scan support for QCN9074
      - support for rx decapsulation offload (data frames in 802.3
        format)

   - Qualcomm phone SoC WiFi (wcn36xx)
      - enable Idle Mode Power Save (IMPS) to reduce power consumption
        during idle

   - Bluetooth driver support for MediaTek MT7922 and MT7921

   - Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and
     Realtek 8822C/8852A

   - Microsoft vNIC driver (mana)
      - support hibernation and kexec

   - Google vNIC driver (gve)
      - support for jumbo frames
      - implement Rx page reuse

  Refactor:

   - Make all writes to netdev->dev_addr go thru helpers, so that we can
     add this address to the address rbtree and handle the updates

   - Various TCP cleanups and optimizations including improvements to
     CPU cache use

   - Simplify the gnet_stats, Qdisc stats' handling and remove
     qdisc->running sequence counter

   - Driver changes and API updates to address devlink locking
     deficiencies"

* tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits)
  Revert "net: avoid double accounting for pure zerocopy skbs"
  selftests: net: add arp_ndisc_evict_nocarrier
  net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter
  net: arp: introduce arp_evict_nocarrier sysctl parameter
  libbpf: Deprecate AF_XDP support
  kbuild: Unify options for BTF generation for vmlinux and modules
  selftests/bpf: Add a testcase for 64-bit bounds propagation issue.
  bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
  bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
  net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c
  net: avoid double accounting for pure zerocopy skbs
  tcp: rename sk_wmem_free_skb
  netdevsim: fix uninit value in nsim_drv_configure_vfs()
  selftests/bpf: Fix also no-alu32 strobemeta selftest
  bpf: Add missing map_delete_elem method to bloom filter map
  selftests/bpf: Add bloom map success test for userspace calls
  bpf: Add alignment padding for "map_extra" + consolidate holes
  bpf: Bloom filter map naming fixups
  selftests/bpf: Add test cases for struct_ops prog
  bpf: Add dummy BPF STRUCT_OPS for test purpose
  ...

Minor cocci warning fixes:
1) Bool return warning fix
2) Unnedded semicolon warning fix

For operations that create vnodes on the server such as CreateFile,
MakeDir or Symlink, the server will store its own current time as
the mtime if the client doesn't pass in a time in the accompanying
StoreStatus structure.

If the server and client clocks are not well synchronized, the client
may see timestamps in the future or inconsistent dependency checks
with "make" for files that are not modified after creation:

make[2]: Warning: File 'arch/x86/kernel/apic/modules.order' has
modification time 0.14 s in the future
make[2]: warning:  Clock skew detected.  Your build may be incomplete.

This is already handled correctly for non yfs operations; also
set the mtime for the corresponding yfs operations.

Changes:
v3: Replace S_IRWXUGO with 0777, per checkpatch
v2: [dhowells] Merge the two xdr_encode_YFSStoreStatus*() functions together
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Link: http://lists.infradead.org/pipermail/linux-afs/2021-October/004395.html

afs_readpage() doesn't get a file pointer when called for a symlink, so
separate it from regular file pointer handling.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Link: https://lore.kernel.org/r/162687508008.276387.6418924257569297305.stgit@warthog.procyon.org.uk/ # rfc
Link: https://lore.kernel.org/r/162981152280.1901565.2264055504466731917.stgit@warthog.procyon.org.uk/
Link: https://lore.kernel.org/r/163005742570.2472992.7800423440314043178.stgit@warthog.procyon.org.uk/ # v2

This reverts commit f1a456f8.

  WARNING: CPU: 1 PID: 6819 at net/core/skbuff.c:5429 skb_try_coalesce+0x78b/0x7e0
  CPU: 1 PID: 6819 Comm: xxxxxxx Kdump: loaded Tainted: G S                5.15.0-04194-gd852503f7711 #16
  RIP: 0010:skb_try_coalesce+0x78b/0x7e0
  Code: e8 2a bf 41 ff 44 8b b3 bc 00 00 00 48 8b 7c 24 30 e8 19 c0 41 ff 44 89 f0 48 03 83 c0 00 00 00 48 89 44 24 40 e9 47 fb ff ff <0f> 0b e9 ca fc ff ff 4c 8d 70 ff 48 83 c0 07 48 89 44 24 38 e9 61
  RSP: 0018:ffff88881f449688 EFLAGS: 00010282
  RAX: 00000000fffffe96 RBX: ffff8881566e4460 RCX: ffffffff82079f7e
  RDX: 0000000000000003 RSI: dffffc0000000000 RDI: ffff8881566e47b0
  RBP: ffff8881566e46e0 R08: ffffed102619235d R09: ffffed102619235d
  R10: ffff888130c91ae3 R11: ffffed102619235c R12: ffff88881f4498a0
  R13: 0000000000000056 R14: 0000000000000009 R15: ffff888130c91ac0
  FS:  00007fec2cbb9700(0000) GS:ffff88881f440000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00007fec1b060d80 CR3: 00000003acf94005 CR4: 00000000003706e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   <IRQ>
   tcp_try_coalesce+0xeb/0x290
   ? tcp_parse_options+0x610/0x610
   ? mark_held_locks+0x79/0xa0
   tcp_queue_rcv+0x69/0x2f0
   tcp_rcv_established+0xa49/0xd40
   ? tcp_data_queue+0x18a0/0x18a0
   tcp_v6_do_rcv+0x1c9/0x880
   ? rt6_mtu_change_route+0x100/0x100
   tcp_v6_rcv+0x1624/0x1830
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull crypto updates from Herbert Xu:
 "API:

   - Delay boot-up self-test for built-in algorithms

  Algorithms:

   - Remove fallback path on arm64 as SIMD now runs with softirq off

  Drivers:

   - Add Keem Bay OCS ECC Driver"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (61 commits)
  crypto: testmgr - fix wrong key length for pkcs1pad
  crypto: pcrypt - Delay write to padata->info
  crypto: ccp - Make use of the helper macro kthread_run()
  crypto: sa2ul - Use the defined variable to clean code
  crypto: s5p-sss - Add error handling in s5p_aes_probe()
  crypto: keembay-ocs-ecc - Add Keem Bay OCS ECC Driver
  dt-bindings: crypto: Add Keem Bay ECC bindings
  crypto: ecc - Export additional helper functions
  crypto: ecc - Move ecc.h to include/crypto/internal
  crypto: engine - Add KPP Support to Crypto Engine
  crypto: api - Do not create test larvals if manager is disabled
  crypto: tcrypt - fix skcipher multi-buffer tests for 1420B blocks
  hwrng: s390 - replace snprintf in show functions with sysfs_emit
  crypto: octeontx2 - set assoclen in aead_do_fallback()
  crypto: ccp - Fix whitespace in sev_cmd_buffer_len()
  hwrng: mtk - Force runtime pm ops for sleep ops
  crypto: testmgr - Only disable migration in crypto_disable_simd_for_test()
  crypto: qat - share adf_enable_pf2vf_comms() from adf_pf2vf_msg.c
  crypto: qat - extract send and wait from adf_vf2pf_request_version()
  crypto: qat - add VF and PF wrappers to common send function
  ...

Pull audit updates from Paul Moore:
 "Add some additional audit logging to capture the openat2() syscall
  open_how struct info.

  Previous variations of the open()/openat() syscalls allowed audit
  admins to inspect the syscall args to get the information contained in
  the new open_how struct used in openat2()"

* tag 'audit-pr-20211101' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
  audit: return early if the filter rule has a lower priority
  audit: add OPENAT2 record to list "how" info
  audit: add support for the openat2 syscall
  audit: replace magic audit syscall class numbers with macros
  lsm_audit: avoid overloading the "key" audit field
  audit: Convert to SPDX identifier
  audit: rename struct node to struct audit_node to prevent future name collisions

Pull selinux updates from Paul Moore:

 - Add LSM/SELinux/Smack controls and auditing for io-uring.

   As usual, the individual commit descriptions have more detail, but we
   were basically missing two things which we're adding here:

      + establishment of a proper audit context so that auditing of
        io-uring ops works similarly to how it does for syscalls (with
        some io-uring additions because io-uring ops are *not* syscalls)

      + additional LSM hooks to enable access control points for some of
        the more unusual io-uring features, e.g. credential overrides.

   The additional audit callouts and LSM hooks were done in conjunction
   with the io-uring folks, based on conversations and RFC patches
   earlier in the year.

 - Fixup the binder credential handling so that the proper credentials
   are used in the LSM hooks; the commit description and the code
   comment which is removed in these patches are helpful to understand
   the background and why this is the proper fix.

 - Enable SELinux genfscon policy support for securityfs, allowing
   improved SELinux filesystem labeling for other subsystems which make
   use of securityfs, e.g. IMA.

* tag 'selinux-pr-20211101' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  security: Return xattr name from security_dentry_init_security()
  selinux: fix a sock regression in selinux_ip_postroute_compat()
  binder: use cred instead of task for getsecid
  binder: use cred instead of task for selinux checks
  binder: use euid from cred instead of using task
  LSM: Avoid warnings about potentially unused hook variables
  selinux: fix all of the W=1 build warnings
  selinux: make better use of the nf_hook_state passed to the NF hooks
  selinux: fix race condition when computing ocontext SIDs
  selinux: remove unneeded ipv6 hook wrappers
  selinux: remove the SELinux lockdown implementation
  selinux: enable genfscon labeling for securityfs
  Smack: Brutalist io_uring support
  selinux: add support for the io_uring access controls
  lsm,io_uring: add LSM hooks to io_uring
  io_uring: convert io_uring to the secure anon inode interface
  fs: add anon_inode_getfile_secure() similar to anon_inode_getfd_secure()
  audit: add filtering for io_uring records
  audit,io_uring,io-wq: add some basic audit support to io_uring
  audit: prepare audit_context for use in calling contexts beyond syscalls

Pass cpu to parse_perf_domain() instead of pcpu.

Fixes: 8486a32d ("cpufreq: Add of_perf_domain_get_sharing_cpumask")
Signed-off-by: Hector.Yuan <hector.yuan@mediatek.com>
[ Viresh: Massaged changelog ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>

Pull RCU updates from Paul McKenney:

 - Miscellaneous fixes

 - Torture-test updates for smp_call_function(), most notably improved
   checking of module parameters.

 - Tasks-trace RCU updates that fix a number of rare but important
   race-condition bugs.

 - Other torture-test updates, most notably better checking of module
   parameters. In addition, rcutorture may once again be run on
   CONFIG_PREEMPT_RT kernels.

 - Torture-test scripting updates, most notably specifying the new
   CONFIG_KCSAN_STRICT kconfig option rather than maintaining an
   ever-changing list of individual KCSAN kconfig options.

* tag 'rcu.2021.11.01a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu: (46 commits)
  rcu: Fix rcu_dynticks_curr_cpu_in_eqs() vs noinstr
  rcu: Always inline rcu_dynticks_task*_{enter,exit}()
  torture: Make kvm-remote.sh print size of downloaded tarball
  torture: Allot 1G of memory for scftorture runs
  tools/rcu: Add an extract-stall script
  scftorture: Warn on individual scf_torture_init() error conditions
  scftorture: Count reschedule IPIs
  scftorture: Account for weight_resched when checking for all zeroes
  scftorture: Shut down if nonsensical arguments given
  scftorture: Allow zero weight to exclude an smp_call_function*() category
  rcu: Avoid unneeded function call in rcu_read_unlock()
  rcu-tasks: Update comments to cond_resched_tasks_rcu_qs()
  rcu-tasks: Fix IPI failure handling in trc_wait_for_one_reader
  rcu-tasks: Fix read-side primitives comment for call_rcu_tasks_trace
  rcu-tasks: Clarify read side section info for rcu_tasks_rude GP primitives
  rcu-tasks: Correct comparisons for CPU numbers in show_stalled_task_trace
  rcu-tasks: Correct firstreport usage in check_all_holdout_tasks_trace
  rcu-tasks: Fix s/rcu_add_holdout/trc_add_holdout/ typo in comment
  rcu-tasks: Move RTGS_WAIT_CBS to beginning of rcu_tasks_kthread() loop
  rcu-tasks: Fix s/instruction/instructions/ typo in comment
  ...