So far intel_spi_write() uses the HW sequencer to do the write. But
the HW sequencer register HSFSTS_CTL does not have such a field for
'Atomic Cycle Sequence', remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

Baytrail/Lynx Point SPI controller's HW sequencer only supports basic
operations. This is determined by the chipset design, however current
codes try to use register values in OPMENU0/OPMENU1 to see whether SW
sequencer should be used, which is wrong. In fact OPMENU0/OPMENU1 can
remain unprogrammed by some bootloaders.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

Intel SPI controller only has a 64 bytes FIFO. This adds a sanity
check before triggering any HW/SW sequencer work.

Additionally for the SW sequencer, if given data length is zero,
we should not mark the 'Data Cycle' bit.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

There are two bugs in current intel_spi_sw_cycle():

- The 'data byte count' field should be the number of bytes
  transferred minus 1
- SSFSTS_CTL is the offset from ispi->sregs, not ispi->base
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Cc: <stable@vger.kernel.org> # v4.11+
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

intel_spi_hw_cycle() and intel_spi_sw_cycle() don't use the parameter
'buf' at all. Remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

The number of protected range registers is not the same on BYT/LPT/
BXT. GPR0 only exists on Apollo Lake and its offset is reserved on
other platforms.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

Intel Cedar Fork has the same SPI serial flash controller than Intel
Denverton. Add the Intel Cedar Fork PCI ID to the driver list of
supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

Intel Lewisburg chipset exposes the SPI serial flash controller as a PCI
device in the same way than Intel Denverton. Add Intel Lewisburg SPI
serial flash PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

Tested against GD25LQ32D but the GD25LQ32C datasheet seems to be
identically feature-wise. Therefore dropping the suffix as it's
probably only indicating the die revision.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

Add support for GD25Q256, a 32MiB SPI Nor flash
from GigaDevice.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

Some manufacturers may use different bit to set QE on different
memories.

The GD25Q256 from GigaDevice is an example, which uses S6(bit 6
of the Status Register-1) to set QE, which is different with
other supported memories from GigaDevice that use S9(bit 1 of
the Status Register-2). This makes it is impossible to select
the quad enable method by distinguishing the MFR. This patch
introduce a quad_enable function which can be set per memory
in the flash_info list table.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

Allow ARM64 support for the Cadence QSPI interface by
adding ARM64 as a dependency.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

Implemented and populated spi-nor mtd PM handlers for resume ops.
spi-nor resume op re-initializes spi-nor flash to its probed
state by calling the newly implemented spi_nor_init() function.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

This patch extracts some chunks from spi_nor_init_params and spi_nor_scan()
 and moves them into a new spi_nor_init() function.

Indeed, spi_nor_init() regroups all the required SPI flash commands to be
sent to the SPI flash memory before performing any runtime operations
(Fast Read, Page Program, Sector Erase, ...). Hence spi_nor_init():
1) removes the flash protection if applicable for certain vendors.
2) sets the Quad Enable bit, if needed, before using Quad SPI protocols.
3) makes the memory enter its (stateful) 4-byte address mode, if needed,
   for SPI flash memory > 128Mbits not supporting the 4-byte address
   instruction set.

spi_nor_scan() now ends by calling spi_nor_init() once the probe phase has
completed. Further patches could also use spi_nor_init() to implement the
mtd->_resume() handler for the spi-nor framework.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

header.minor is of type u8 and cannot be negative.

Detected by CoverityScan CID#1417858 ("Integer handling issues")

Fixes: f384b352 ("mtd: spi-nor: parse Serial Flash Discoverable
Parameters (SFDP) tables")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>

Pull SCSI fixes from James Bottomley:

 - a couple of serious fixes: use after free and blacklist for WRITE
   SAME

 - one error leg fix: write_pending failure

 - one user experience problem: do not override max_sectors_kb

 - one minor unused function removal

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ibmvscsis: Fix write_pending failure path
  scsi: libiscsi: Remove iscsi_destroy_session
  scsi: libiscsi: Fix use-after-free race during iscsi_session_teardown
  scsi: sd: Do not override max_sectors_kb sysfs setting
  scsi: sd: Implement blacklist option for WRITE SAME w/ UNMAP

Pull i2c fixes from Wolfram Sang:
 "I2C has three driver fixes for the newly introduced drivers and one ID
  addition for the i801 driver"

* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i2c-stm32f7: make structure stm32f7_setup static const
  i2c: ensure termination of *_device_id tables
  i2c: i801: Add support for Intel Cedar Fork
  i2c: stm32f7: fix setup structure

Pull MMC fixes from Ulf Hansson:
 "MMC core:

   - Fix driver strength selection when selecting hs400es

   - Delete bounce buffer handling:

     This change fixes a problem related to how bounce buffers are being
     allocated. However, instead of trying to fix that, let's just
     remove the mmc bounce buffer code altogether, as it has practically
     no use.

  MMC host:

   - meson-gx: A couple of fixes related to clock/phase/tuning

   - sdhci-xenon: Fix clock resource by adding an optional bus clock"

* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
  mmc: meson-gx: include tx phase in the tuning process
  mmc: meson-gx: fix rx phase reset
  mmc: meson-gx: make sure the clock is rounded down
  mmc: Delete bounce buffer handling
  mmc: core: add driver strength selection when selecting hs400es

Merge tag 'hwmon-for-linus-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fix from Guenter Roeck:
 "Fix up error path in xgene driver"

* tag 'hwmon-for-linus-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (xgene) Fix up error handling path mixup in 'xgene_hwmon_probe()'

Pull clk fixes from Stephen Boyd:

 - build fix to export the clk_bulk_prepare() symbol

 - suspend fix for Samsung Exynos SoCs where we need to keep clks on
   across suspend

 - two critical clk markings for clks that shouldn't ever turn off on
   Rockchip SoCs

 - a fix for a copy-paste mistake on Rockchip rk3128 causing some clks
   to touch the same bit and trample over one another

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: samsung: exynos4: Enable VPLL and EPLL clocks for suspend/resume cycle
  clk: Export clk_bulk_prepare()
  clk: rockchip: add sclk_timer5 as critical clock on rk3128
  clk: rockchip: fix up rk3128 pvtm and mipi_24m gate regs error
  clk: rockchip: add pclk_pmu as critical clock on rk3128

Pull ARC udpates from Vineet Gupta:

 - updates for various platforms

 - boot log updates for upcoming HS48 family of cores (dual issue)

* tag 'arc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [plat-hsdk]: Add reset controller node to manage ethernet reset
  ARC: [plat-hsdk]: Temporary fix to set CPU frequency to 1GHz
  ARC: fix allnoconfig build warning
  ARCv2: boot log: identify HS48 cores (dual issue)
  ARC: boot log: decontaminate ARCv2 ISA_CONFIG register
  arc: remove redundant UTS_MACHINE define in arch/arc/Makefile
  ARC: [plat-eznps] Update platform maintainer as Noam left
  ARC: [plat-hsdk] use actual clk driver to manage cpu clk
  ARC: [*defconfig] Reenable soft lock-up detector
  ARC: [plat-axs10x] sdio: Temporary fix of sdio ciu frequency
  ARC: [plat-hsdk] sdio: Temporary fix of sdio ciu frequency
  ARC: [plat-axs103] Add temporary quirk to reset ethernet IP

Pull xfs fixes from Darrick Wong:

 - fix a race between overlapping copy on write aio

 - fix cow fork swapping when we defragment reflinked files

* tag 'xfs-4.14-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: handle racy AIO in xfs_reflink_end_cow
  xfs: always swap the cow forks when swapping extents

Pull block fixes from Jens Axboe:
 "A collection of fixes for this series. This contains:

   - NVMe pull request from Christoph, one uuid attribute fix, and one
     fix for the controller memory buffer address for remapped BARs.

   - use-after-free fix for bsg, from Benjamin Block.

   - bcache race/use-after-free fix for a list traversal, fixing a
     regression in this merge window. From Coly Li.

   - null_blk change configfs dependency change from a 'depends' to a
     'select'. This is a change from this merge window as well. From me.

   - nbd signal fix from Josef, fixing a regression introduced with the
     status code changes.

   - nbd MAINTAINERS mailing list entry update.

   - blk-throttle stall fix from Joseph Qi.

   - blk-mq-debugfs fix from Omar, fixing an issue where we don't
     register the IO scheduler debugfs directory, if the driver is
     loaded with it. Only shows up if you switch through the sysfs
     interface"

* 'for-linus' of git://git.kernel.dk/linux-block:
  bsg-lib: fix use-after-free under memory-pressure
  nvme-pci: Use PCI bus address for data/queues in CMB
  blk-mq-debugfs: fix device sched directory for default scheduler
  null_blk: change configfs dependency to select
  blk-throttle: fix possible io stall when upgrade to max
  MAINTAINERS: update list for NBD
  nbd: fix -ERESTARTSYS handling
  nvme: fix visibility of "uuid" ns attribute
  bcache: use llist_for_each_entry_safe() in __closure_wake_up()

Pull PCI fixes from Bjorn Helgaas:
 "Fix legacy IDE probe issues exposed by recent PCI core IRQ mapping
  changes (Bartlomiej Zolnierkiewicz, Lorenzo Pieralisi)"

* tag 'pci-v4.14-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  ide: fix IRQ assignment for PCI bus order probing
  ide: pci: free PCI BARs on initialization failure
  ide: free hwif->portdev on hwif_init() failure

Pull arm64 fixes from Catalin Marinas:

 - Bring initialisation of user space undefined instruction handling
   early (core_initcall) since late_initcall() happens after modprobe in
   initramfs is invoked. Similar fix for fpsimd initialisation

 - Increase the kernel stack when KASAN is enabled

 - Bring the PCI ACS enabling earlier via the
   iort_init_platform_devices()

 - Fix misleading data abort address printing (decimal vs hex)

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Ensure fpsimd support is ready before userspace is active
  arm64: Ensure the instruction emulation is ready for userspace
  arm64: Use larger stacks when KASAN is selected
  ACPI/IORT: Fix PCI ACS enablement
  arm64: fix misleading data abort decoding

Pull KVM fixes from Radim Krčmář:

 - fix PPC XIVE interrupt delivery

 - fix x86 RCU breakage from asynchronous page faults when built without
   PREEMPT_COUNT

 - fix x86 build with -frecord-gcc-switches

 - fix x86 build without X86_LOCAL_APIC

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: add X86_LOCAL_APIC dependency
  x86/kvm: Move kvm_fastop_exception to .fixup section
  kvm/x86: Avoid async PF preempting the kernel incorrectly
  KVM: PPC: Book3S: Fix server always zero from kvmppc_xive_get_xive()

Pull rdma fixes from Doug Ledford:
 "This is a pretty small pull request. Only 6 patches in total. There
  are no outstanding -rc patches on the mailing list after this pull
  request, so only if some new issues are discovered in the remainder of
  the rc cycles will you hear from me again.

  Summary:
   - a fix for iwpm netlink usage
   - a fix for error unwinding in mlx5
   - two fixes to vlan handling in qedr
   - a couple small i40iw fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  i40iw: Fix port number for query QP
  i40iw: Add missing memory barriers
  RDMA/qedr: Parse vlan priority as sl
  RDMA/qedr: Parse VLAN ID correctly and ignore the value of zero
  IB/mlx5: Fix label order in error path handling
  RDMA/iwpm: Properly mark end of NL messages

Pull btrfs fixes from David Sterba:
 "Two more fixes for bugs introduced in 4.13.

  The sector_t problem with 32bit architecture and !LBDAF config seems
  serious but the number of affected deployments is hopefully low.

  The clashing status bits could lead to a confusing in-memory state of
  the whole-filesystem operations if used with the quota override sysfs
  knob"

* 'for-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix overlap of fs_info::flags values
  btrfs: avoid overflow when sector_t is 32 bit

Pull ceph fixes from Ilya Dryomov:
 "Two fixups for CephFS snapshot-handling patches in -rc1"

* tag 'ceph-for-4.14-rc4' of git://github.com/ceph/ceph-client:
  ceph: fix __choose_mds() for LSSNAP request
  ceph: properly queue cap snap for newly created snap realm

DW ethernet controller on HSDK hangs sometimes after SW reset, so
add reset node to make possible to reset DW ethernet controller HW.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Pull overlayfs fixes from Miklos Szeredi:
 "Fix a regression in 4.14 and one in 4.13. The latter is a case when
  Docker is doing something it really shouldn't and gets away with it.
  We now print a warning instead of erroring out.

  There are also fixes to several error paths"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: fix regression caused by exclusive upper/work dir protection
  ovl: fix missing unlock_rename() in ovl_do_copy_up()
  ovl: fix dentry leak in ovl_indexdir_cleanup()
  ovl: fix dput() of ERR_PTR in ovl_cleanup_index()
  ovl: fix error value printed in ovl_lookup_index()
  ovl: fix may_write_real() for overlayfs directories

Pull powerpc fixes from Michael Ellerman:
 "Nine small fixes, really nothing that stands out.

  A work-around for a spurious MCE on Power9. A CXL fault handling fix,
  some fixes to the new XIVE code, and a fix to the new 32-bit
  STRICT_KERNEL_RWX code.

  Fixes for old code/stable: an fix to an incorrect TLB flush on boot
  but not on any current machines, a compile error on 4xx and a fix to
  memory hotplug when using radix (Power9).

  Thanks to: Anton Blanchard, Cédric Le Goater, Christian Lamparter,
  Christophe Leroy, Christophe Lombard, Guenter Roeck, Jeremy Kerr,
  Michael Neuling, Nicholas Piggin"

* tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/powernv: Increase memory block size to 1GB on radix
  powerpc/mm: Call flush_tlb_kernel_range with interrupts enabled
  powerpc/xive: Clear XIVE internal structures when a CPU is removed
  powerpc/xive: Fix IPI reset
  powerpc/4xx: Fix compile error with 64K pages on 40x, 44x
  powerpc: Fix action argument for cpufeatures-based TLB flush
  cxl: Fix memory page not handled
  powerpc: Fix workaround for spurious MCE on POWER9
  powerpc: Handle MCE on POWER9 with only DSISR bit 30 set

Pull drm fixes from Dave Airlie:
 "Some i915 fixes from the last two weeks (as they were on a strange
  base and I just waited for rc3), also a single sun4i hdmi fix"

* tag 'drm-fixes-for-v4.14-rc4' of git://people.freedesktop.org/~airlied/linux:
  drm/i915/glk: Fix DMC/DC state idleness calculation
  drm/i915/cnl: Reprogram DMC firmware after S3/S4 resume
  drm/i915: Fix DDI PHY init if it was already on
  drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
  drm/i915/bios: ignore HDMI on port A
  drm/i915: remove redundant variable hw_check
  drm/i915: always update ELD connector type after get modes

Pull watchddog clean-up and fixes from Thomas Gleixner:
 "The watchdog (hard/softlockup detector) code is pretty much broken in
  its current state. The patch series addresses this by removing all
  duct tape and refactoring it into a workable state.

  The reasons why I ask for inclusion that late in the cycle are:

   1) The code causes lockdep splats vs. hotplug locking which get
      reported over and over. Unfortunately there is no easy fix.

   2) The risk of breakage is minimal because it's already broken

   3) As 4.14 is a long term stable kernel, I prefer to have working
      watchdog code in that and the lockdep issues resolved. I wouldn't
      ask you to pull if 4.14 wouldn't be a LTS kernel or if the
      solution would be easy to backport.

   4) The series was around before the merge window opened, but then got
      delayed due to the UP failure caused by the for_each_cpu()
      surprise which we discussed recently.

  Changes vs. V1:

   - Addressed your review points

   - Addressed the warning in the powerpc code which was discovered late

   - Changed two function names which made sense up to a certain point
     in the series. Now they match what they do in the end.

   - Fixed a 'unused variable' warning, which got not detected by the
     intel robot. I triggered it when trying all possible related config
     combinations manually. Randconfig testing seems not random enough.

  The changes have been tested by and reviewed by Don Zickus and tested
  and acked by Micheal Ellerman for powerpc"

* 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
  watchdog/core: Put softlockup_threads_initialized under ifdef guard
  watchdog/core: Rename some softlockup_* functions
  powerpc/watchdog: Make use of watchdog_nmi_probe()
  watchdog/core, powerpc: Lock cpus across reconfiguration
  watchdog/core, powerpc: Replace watchdog_nmi_reconfigure()
  watchdog/hardlockup/perf: Fix spelling mistake: "permanetely" -> "permanently"
  watchdog/hardlockup/perf: Cure UP damage
  watchdog/hardlockup: Clean up hotplug locking mess
  watchdog/hardlockup/perf: Simplify deferred event destroy
  watchdog/hardlockup/perf: Use new perf CPU enable mechanism
  watchdog/hardlockup/perf: Implement CPU enable replacement
  watchdog/hardlockup/perf: Implement init time detection of perf
  watchdog/hardlockup/perf: Implement init time perf validation
  watchdog/core: Get rid of the racy update loop
  watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage
  watchdog/sysctl: Clean up sysctl variable name space
  watchdog/sysctl: Get rid of the #ifdeffery
  watchdog/core: Clean up header mess
  watchdog/core: Further simplify sysctl handling
  watchdog/core: Get rid of the thread teardown/setup dance
  ...

We register the pm/hotplug callbacks for FPSIMD as late_initcall,
which happens after the userspace is active (from initramfs via
populate_rootfs, a rootfs_initcall). Make sure we are ready even
before the userspace could potentially use it, by promoting to
a core_initcall.

Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

We trap and emulate some instructions (e.g, mrs, deprecated instructions)
for the userspace. However the handlers for these are registered as
late_initcalls and the userspace could be up and running from the initramfs
by that time (with populate_rootfs, which is a rootfs_initcall()). This
could cause problems for the early applications ending up in failure
like :

[   11.152061] modprobe[93]: undefined instruction: pc=0000ffff8ca48ff4

This patch promotes the specific calls to core_initcalls, which are
guaranteed to be completed before we hit userspace.

Cc: stable@vger.kernel.org
Cc: Dave Martin <dave.martin@arm.com>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: James Morse <james.morse@arm.com>
Reported-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Memory hot unplug on PowerNV radix hosts is broken. Our memory block
size is 256MB but since we map the linear region with very large
pages, each pte we tear down maps 1GB.

A hot unplug of one 256MB memory block results in 768MB of memory
getting unintentionally unmapped. At this point we are likely to oops.

Fix this by increasing our memory block size to 1GB on PowerNV radix
hosts.

Fixes: 4b5d62ca ("powerpc/mm: add radix__remove_section_mapping()")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

One bugfix in sun4i for 4.14

* tag 'drm-misc-fixes-2017-10-05' of git://anongit.freedesktop.org/git/drm-misc:
  drm/sun4i: hdmi: Disable clks in bind function error path and unbind function

Merge tag 'drm-intel-fixes-2017-10-04' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes

drm/i915 fixes for 4.14-rc4:

All 3 highest GLK bugs fixed by Imre:
- GLK drv reload - Fix DDI Phy init if it was already on.
- GLK suspend resume - Reprogram DMC firmware after s3/s4.
- GLK DC states - Fix idleness calculation.

* tag 'drm-intel-fixes-2017-10-04' of git://anongit.freedesktop.org/git/drm-intel:
  drm/i915/glk: Fix DMC/DC state idleness calculation
  drm/i915/cnl: Reprogram DMC firmware after S3/S4 resume
  drm/i915: Fix DDI PHY init if it was already on