TXGAPK stands for TX power gap calibration. Use this calibration to
compensate TX power gap to output expected power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-8-pkshih@realtek.com

DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output signals with expected quality.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-7-pkshih@realtek.com

DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-6-pkshih@realtek.com

RX DCK is receiver DC calibration. This will calibrate DC offset to
reflect correct received signal strength indicator, so mechanisms like CCA
can have normalized values.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-5-pkshih@realtek.com

IQ signal calibration is a basic and important calibration to yield good RF
performance. Do this calibration on AP channel if we are going to connect.
During scanning phase, it transmits with low data rate, so without IQK
RF performance is still acceptable.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-4-pkshih@realtek.com

We are going to do RF calibrations in firmware, so driver needs to provide
channel information for calibrations, which can do the same things as
they did in driver.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-3-pkshih@realtek.com

The RF calibrations should be executed one by one, so add a completion
to ensure one is finish before next. The report from C2H event contains
state and optional version, and we only check the state for now. We also
care about the time a RF calibration takes, so record start time before
asking firmware to do calibration and get the delta time when receiving
report.

Consider SER recovery, we can't receive C2H event, use half of argument
'ms' as fixed delay that is 2 times of measured maximum time of
calibrations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-2-pkshih@realtek.com

Calling spi_sync() unconditionally sets the spi field of struct
spi_message. Therefore setting msg.spi = spi before calling spi_sync()
has no effect and can be removed.

(spi_message_add_tail() does not access this field.)
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240201201248.2334798-2-dlechner@baylibre.com

The CW1200 uses two GPIOs to control the powerup and reset
pins, get these from GPIO descriptors instead of being passed
as platform data from boardfiles.

The RESET line will need to be marked as active low as we will
let gpiolib handle the polarity inversion.

The SDIO case is a bit special since the "card" need to be
powered up before it gets detected on the SDIO bus and
properly probed. Fix this by using board-specific GPIOs
assigned to device "NULL".

There are currently no in-tree users.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240131-descriptors-wireless-v1-6-e1c7c5d68746@linaro.org

The driver includes the legacy GPIO header <linux/gpio.h>
but does not use any symbols from it. Drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240131-descriptors-wireless-v1-5-e1c7c5d68746@linaro.org

The mwifiex driver include two legacy GPIO headers but does
not use symbols from any of them.

The driver does contain some "gpio" handling code, but this
is some custom GPIO interface, not the Linux GPIO.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240131-descriptors-wireless-v1-4-e1c7c5d68746@linaro.org

The driver is using all the modern abstractions to obtain and use
GPIOs and the legacy <linux/gpio.h> header is unused, so drop it.

Fixes: a8e59744 ("gpiolib: split linux/gpio/driver.h out of linux/gpio.h")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240131-descriptors-wireless-v1-3-e1c7c5d68746@linaro.org

The file is including the legacy GPIO header <linux/gpio.h> but
is not using any symbols from it, drop the header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240131-descriptors-wireless-v1-2-e1c7c5d68746@linaro.org

Sparse warns:

drivers/net/wireless/st/cw1200/cw1200_spi.c:83:17:    got restricted __le16 [usertype]
drivers/net/wireless/st/cw1200/cw1200_spi.c:148:17: warning: incorrect type in assignment (different base types)
drivers/net/wireless/st/cw1200/cw1200_spi.c:148:17:    expected unsigned short [addressable] [assigned] [usertype] regaddr
drivers/net/wireless/st/cw1200/cw1200_spi.c:148:17:    got restricted __le16 [usertype]

These cpu_to_le16() calls are not really making any sense to me. On a big
endian system we first convert regaddr from big to little using cpu_to_le16()
but immediately after we convert them back to big endian? So just remove them.

Compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130151556.2315951-4-kvalo@kernel.org

drivers/net/wireless/rsi/rsi_91x_usb.c:235:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:236:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:237:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:238:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:244:36: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:245:35: warning: restricted __le32 degrades to integer

These cpu_to_le32() are not making sense. With usb_reg_buf we handle the values
byte at a time to make sure usb_reg_buf is in little endian so no need to
convert anything. And usb_control_msg() expects to have the values in native
endian anyway. So just remove these so they are not spamming our logs.

Compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130151556.2315951-3-kvalo@kernel.org

Sparse warns:

drivers/net/wireless/zydas/zd1211rw/zd_usb.c:383:24: warning: implicit cast from nocast type
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:419:24: warning: implicit cast from nocast type

This is an ancient driver which has not have any meaningfuli changes for a long
time and hopefully removed soon. So just remove the __nocast to get rid of the
sparse warnings.

Compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130151556.2315951-2-kvalo@kernel.org

TP-Link TL-WN823N V2 (2357:0135) is based on rtl8192fu and has been
tested to work with the rtl8xxxu driver.
Signed-off-by: Chun Qiu <cqca@cock.lu>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240129053030.16369-1-cqca@cock.lu

In the for statement of lbs_allocate_cmd_buffer(), if the allocation of
cmdarray[i].cmdbuf fails, both cmdarray and cmdarray[i].cmdbuf needs to
be freed. Otherwise, there will be memleaks in lbs_allocate_cmd_buffer().

Fixes: 876c9d3a ("[PATCH] Marvell Libertas 8388 802.11b/g USB driver")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126075336.2825608-1-alexious@zju.edu.cn

These can only be exported if cfg80211's kunit is enabled,
since they're otherwise static. kunit itself can be enabled
even if cfg80211's kunit isn't. Fix that by using the right
macro.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402040534.6AEKtZ7Y-lkp@intel.com/
Fixes: 45d43937 ("wifi: cfg80211: add a kunit test for 6 GHz colocated AP parsing")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

dmi_get_system_info() will statically return NULL when the
kernel is compiled without CONFIG_DMI, leading to compiler
warnings. Fix that by printing "<unknown>" in that case.

Fixes: c3f40c3e ("iwlwifi: mvm: add US/CA to TAS block list if OEM isn't allowed")
Fixes: 9457077d ("wifi: iwlwifi: mvm: Add debugfs to get TAS status")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When the system is compiled without CONFIG_DMI, the function
here statically returns NULL, leading to a compiler warning.
Catch that and print "<unknown>" in that case.

While at it, fix some indentation in the function.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402030641.zUTuACYV-lkp@intel.com/
Fixes: 09059c67 ("wifi: iwlwifi: prepare for reading PPAG table from UEFI")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The user of this function passes a pointer to a value that
doesn't exist when compiled w/o CONFIG_ACPI. Since we don't
need the value then, make the non-ACPI version a macro to
allow it to still build.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402031454.syX4cSGN-lkp@intel.com/
Fixes: c4c95454 ("wifi: iwlwifi: implement WPFC ACPI table loading")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In the following patch, iwl_mvm_roc_duration_and_delay and
iwl_mvm_roc_add_cmd will be called also from time-event.c.
Move then there (where they more belong) and make then
public.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240201155157.3edafc4d59aa.Ic68e90758bcad9ae00e0aa602101842dac60e1a1@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Start supporting API version 88 for new devices.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.e35556d3f956.I6543857041a33e2b35e67eecf648c9cc6972e60a@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

AX210 and above have this logic offloaded in the firmware and it just
ignores the command coming from the driver.
Stop sending it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240201155157.4e3e0b52f98b.I7e9481050921d95c38f5a21ccc47112b3698e859@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

For each DSM function, try to first read it from the UEFI.
If the UEFI WIFI GUID is unclocked, or the DSM function in
UEFI is invalid/unavailable - read it from ACPI.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.27dd626ce2bd.Ib90bab74a9d56deb2362edb712294360e4ddae5b@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Move all the common items (functions, enumerations and mcaros)
to regulatory.h/c files, and rename it to a common name.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.eae9bcbc0023.If1175f3143d6369076669ddd5d6ad4df0ee00659@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

As DSMs are going to be read from UEFI too, we need a unified API
to get DSMs for both ACPI and UEFI.

The difference in getting DSM in each one of these methods (ACPI, UEFI)
is in the GUID, revision (0 for ACPI, 4 for UEFI), and size of the DSM
values (8 or 32 for ACPI, 32 for UEFI).

Therefore, change the iwl_acpi_get_dsm_x() to iwl_acpi_get_dsm() which
determines the GUID, revision (these two are the same for all WiFi DSMs),
and size (based on a func-to-size mapping) internally.

While at it, fix DSM_FUNC_RFI_CONFIG to expect a 32-bit value
(as defined in Intel BIOS spec) and not a 8-bit one.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.1bcd7072a7a5.I344ee0a11abbc27da0c693187d1b8bee653aaeef@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

These functions shouldn't be ACPI_CONFIG dependent, as they don't
access the ACPI. The functions that really access ACPI -
already handle the case that CONFIG_ACPI is not set.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.1412e6d561f8.I84f67478d01b576457e1bf489fbcb044adfda6fe@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

RFI configuration moved from internal guid to the wifi guid, DSM
function 11. Update reading RFI configuration from BIOS.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.f4e62435310d.I4f9b6860dd8e3c7ae1f816be5ff8b5967eee266f@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Try to read the ECKV table from UEFI first,
and if the WIFI UEFI tables are unlocked or the
table doesn't exist - try to read it from ACPI.

Change iwl_acpi_get_eckv() to receive fwrt as argument so
it will be the same as all iwl_acpi_get_x() functions,
so it could  be generated by the macro.

While at it - move the reading of ECKV to INIT stage. There is no
reason to read it each time we load the FW.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.d4937cc00727.I36e5fc7f7850229b9b377c80b5203aa47137c97c@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Try to read the WRDD table from UEFI first,
and if the WIFI UEFI tables are unlocked or the
table doesn't exist - try to read it from ACPI.

Change iwl_acpi_get_mcc() to receive fwrt as argument so
it will be the same as all iwl_acpi_get_x() functions,
so it could be generated by the macro.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.5d52eeb109f7.I4d81700a7ae7fe2dfee14e363de358be59de7823@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

In version 2, listen_lmac becomes reserved.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240201155157.df1890aba2fd.Icad9ba10f8bab770adc6a559b2c7bff5cccbffe9@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Set fast balance scan in case of active P2P GO, regardless of the
BSS DTIM interval.
This will increase the chances of scheduler to successfully schedule
out-of-channel events.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240201155157.310a00388e11.Ib136140dffa8704e68ff14e8fb69d35b97057171@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

New tx devices may have issues sending NDPs from the host.
Send a CQM event instead. If the AP is really gone, we will get a beacon
loss and disconnect.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Berg, Johannes <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240201155157.e95d53448e94.I0ec92f1ca56a62cd8c13390b9fe60e9a7e9411c7@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Try to read the SPLC table from UEFI first,
and if the WIFI UEFI tables are unlocked or the
table doesn't exist - try to read it from ACPI
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.3d9d835b6edb.I7ea262df9431ced787b77c87149c6d7bddb7e7d6@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

As the iwl_bios_get_x() functions are now generated using a macro,
and this macro requires the all iwl_acpi_get_x() to have the same
prototype, change iwl_acpi_get_pwr_limit() to return a int
and the actuall power limit will be filled in a pointer function
parameter.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.4cce81198afe.Ice8b1b97a68da9ec7b5a4799ddb668642198e1af@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Add some kernel-doc for a union, and fix a couple of typos
I noticed looking through this.

Link: https://msgid.link/20240131220227.7fd507f09bb1.I278edc9a3d5de7fddcd84009a93c494c42686b68@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Saw this while going through the code, this function
hasn't existed for a while now; remove it.

Link: https://msgid.link/20240131220039.6fdb8cbf4814.I6c46065b836cafd93df676dd88c99a626a25bf46@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Fix some more kernel-doc warnings in FW API definitions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240131213817.9f30c6529216.I69e98612c6c81cf1b7bd480d8041b5d3e25610d3@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>