Move MTK_WDMA_RESET_IDX configuration in mtk_wdma_rx_reset routine.
Increase poll timeout to 10ms in order to be aligned with vendor sdk.
This is a preliminary patch to add Wireless Ethernet Dispatcher reset
support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Miquel Raynal says:

====================
Marvell nvmem mac addresses support

Now that we are aligned on how to make information available from static
storage media to drivers like Ethernet controller drivers or switch
drivers by using nvmem cells and going through the whole nvmem
infrastructure, here are two driver updates to reflect these changes.

Prior to the driver updates, I propose:
* Reverting binding changes which should have never been accepted like
  that.
* A conversion of the (old) Prestera and DFX server bindings (optional,
  can be dropped if not considered necessary).
* A better description of the more recent Prestera PCI switch.

Please mind that this series cannot break anything since retrieving the
MAC address Prestera driver has never worked upstream, because the (ONIE
tlv) driver supposed to export the MAC address has not been accepted in
its original form and has been updated to the nvmem-layout
infrastructure (bindings have been merged, the code remains to be
applied).
====================

Link: https://lore.kernel.org/r/20221124111556.264647-1-miquel.raynal@bootlin.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The ONIE standard describes the organization of tlv (type-length-value)
arrays commonly stored within NVMEM devices on common networking
hardware.

Several drivers already make use of NVMEM cells for purposes like
retrieving a default MAC address provided by the manufacturer.

What made ONIE tables unusable so far was the fact that the information
where "dynamically" located within the table depending on the
manufacturer wishes, while Linux NVMEM support only allowed statically
defined NVMEM cells. Fortunately, this limitation was eventually tackled
with the introduction of discoverable cells through the use of NVMEM
layouts, making it possible to extract and consistently use the content
of tables like ONIE's tlv arrays.

Parsing this table at runtime in order to get various information is now
possible. So, because many Marvell networking switches already follow
this standard, let's consider using NVMEM cells as a new valid source of
information when looking for a base MAC address, which is one of the
primary uses of these new fields. Indeed, manufacturers following the
ONIE standard are encouraged to provide a default MAC address there, so
let's eventually use it if no other MAC address has been found using the
existing methods.

Link: https://opencomputeproject.github.io/onie/design-spec/hw_requirements.htmlSigned-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This driver fist makes an expensive DT lookup to retrieve its DT node
(this is a PCI driver) in order to later search for the
base-mac-provider property. This property has no reality upstream and
this code should not have been accepted like this in the first
place. Instead, there is a proper nvmem interface that should be
used. Let's avoid these extra lookups and rely on the nvmem internal
logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Export

	of_get_mac_addr_nvmem()

and rename it to

	of_get_mac_address_nvmem()

in order to fit the convention followed by the existing exported helpers
of the same kind.

This way, OF compatible drivers using eg. fwnode_get_mac_address() can
do a direct call to it instead of calling of_get_mac_address() just for
the nvmem step, avoiding to repeat an expensive DT lookup which has
already been done once.

Eventually, fwnode_get_mac_address() should probably be updated to
perform the nvmem lookup directly, but as of today, nvmem cells seem not
to be supported by ACPI yet which would defeat this kind of extension.
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Even though the devices have very little in common beside the name and
the main "switch" feature, Marvell Prestera switch family is also
composed of PCI-only devices which can receive additional static
properties, like nvmem cells to point at MAC addresses, for
instance. Let's describe them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The currently described switch family is named AlleyCat3, it is a memory
mapped switch found on Armada XP boards.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Even though this description is not used anywhere upstream (no matching
driver), while on this file I decided I would try a conversion to yaml
in order to clarify the prestera family description.

I cannot keep the nodename dfx-server@xxxx so I switched to dfx-bus@xxxx
which matches simple-bus.yaml. Otherwise I took the example context from
the only user of this compatible: armada-xp-98dx3236.dtsi, which is a
rather old and not perfect DT.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This reverts commit 40acc052.

marvell,prestera.txt is an old file describing the old Alleycat3
standalone switches. The commit mentioned above actually hacked these
bindings to add support for a device tree property for a more modern
version of the IP connected over PCI, using only the generic compatible
in order to retrieve the device node from the prestera driver to read
one static property.

The problematic property discussed here is "base-mac-provider". The
original intent was to point to a nvmem device which could produce the
relevant nvmem-cell. This property has never been acked by DT
maintainers and fails all the layering that has been brought with the nvmem
bindings by pointing at a nvmem producer, bypassing the existing nvmem
bindings, rather than a nvmem cell directly. Furthermore, the property
cannot even be used upstream because it expected the ONIE tlv driver to
produce a specific cell, driver which used nacked bindings and thus was
never merged, replaced by a more integrated concept: the nvmem-layout.

So let's forget about this temporary addition, safely avoiding the need
for any backward compatibility handling. A new (yaml) binding file will
be brought with the prestera bindings, and there we will actually
include a description of the modern IP over PCI, including the right way
to point to a nvmem cell.

Cc: Vadym Kochan <vadym.kochan@plvision.eu>
Cc: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

====================
bpf-next 2022-11-25

We've added 101 non-merge commits during the last 11 day(s) which contain
a total of 109 files changed, 8827 insertions(+), 1129 deletions(-).

The main changes are:

1) Support for user defined BPF objects: the use case is to allocate own
   objects, build own object hierarchies and use the building blocks to
   build own data structures flexibly, for example, linked lists in BPF,
   from Kumar Kartikeya Dwivedi.

2) Add bpf_rcu_read_{,un}lock() support for sleepable programs,
   from Yonghong Song.

3) Add support storing struct task_struct objects as kptrs in maps,
   from David Vernet.

4) Batch of BPF map documentation improvements, from Maryam Tahhan
   and Donald Hunter.

5) Improve BPF verifier to propagate nullness information for branches
   of register to register comparisons, from Eduard Zingerman.

6) Fix cgroup BPF iter infra to hold reference on the start cgroup,
   from Hou Tao.

7) Fix BPF verifier to not mark fentry/fexit program arguments as trusted
   given it is not the case for them, from Alexei Starovoitov.

8) Improve BPF verifier's realloc handling to better play along with dynamic
   runtime analysis tools like KASAN and friends, from Kees Cook.

9) Remove legacy libbpf mode support from bpftool,
   from Sahid Orentino Ferdjaoui.

10) Rework zero-len skb redirection checks to avoid potentially breaking
    existing BPF test infra users, from Stanislav Fomichev.

11) Two small refactorings which are independent and have been split out
    of the XDP queueing RFC series, from Toke Høiland-Jørgensen.

12) Fix a memory leak in LSM cgroup BPF selftest, from Wang Yufen.

13) Documentation on how to run BPF CI without patch submission,
    from Daniel Müller.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================

Link: https://lore.kernel.org/r/20221125012450.441-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit f72cd76b.
This patch is so broken, it hurts. Apparently no one reviewed it and it
passed the build testing (because the code was compiled out), but it was
obviously never compile-tested, since it produces the following build
error, due to an incomplete conversion where an extra argument was left,
although the function being called was left:

stmmac_main.c: In function ‘stmmac_cmdline_opt’:
stmmac_main.c:7586:28: error: too many arguments to function ‘sysfs_streq’
 7586 |                 } else if (sysfs_streq(opt, "pause:", 6)) {
      |                            ^~~~~~~~~~~
In file included from ../include/linux/bitmap.h:11,
                 from ../include/linux/cpumask.h:12,
                 from ../include/linux/smp.h:13,
                 from ../include/linux/lockdep.h:14,
                 from ../include/linux/mutex.h:17,
                 from ../include/linux/notifier.h:14,
                 from ../include/linux/clk.h:14,
                 from ../drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:17:
../include/linux/string.h:185:13: note: declared here
  185 | extern bool sysfs_streq(const char *s1, const char *s2);
      |             ^~~~~~~~~~~

What's even worse is that the patch is flat out wrong. The stmmac_cmdline_opt()
function does not parse sysfs input, but cmdline input such as
"stmmaceth=tc:1,pause:1". The pattern of using strsep() followed by
strncmp() for such strings is not unique to stmmac, it can also be found
mainly in drivers under drivers/video/fbdev/.

With strncmp("tc:", 3), the code matches on the "tc:1" token properly.
With sysfs_streq("tc:"), it doesn't.

Fixes: f72cd76b ("net: stmmac: use sysfs_streq() instead of strncmp()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20221125105304.3012153-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add CDC-ECM support for LARA-L6.

LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface

In CDC-ECM mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Link: https://lore.kernel.org/r/20221124112811.3548-1-davide.tronchin.94@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

1. Added support to filter packets based on IP fragment.
For IPv4 packets check for ip_flag == 0x20 (more fragment bit set).
For IPv6 packets check for next_header == 0x2c (next_header set to
'fragment header for IPv6')
2. Added configuration support from both "ethtool ntuple" and "tc flower".
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All wed versions should enable the wcid overwritten feature,
since the wcid size is controlled by the wlan driver.
Tested-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-11-23 (ice)

This series contains updates to ice driver only.

Karol adjusts check of PTP hardware to wait longer but check more often.

Brett removes use of driver defined link speed; instead using the values
from ethtool.h, utilizing static tables for indexing.

Ben adds tracking of stats in order to accumulate reported statistics that
were previously reset by hardware.

Marcin fixes issues setting RXDID when queues are asymmetric.

Anatolii re-introduces use of define over magic number; ICE_RLAN_BASE_S.
---
v3:
 - Dropped, previous, patch 2
v2:
Patch 5
 - Convert some allocations to non-managed
 - Remove combined error checking; add error checks for each call
 - Remove excess NULL checks
 - Remove unnecessary NULL sets and newlines
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Anirudh Venkataramanan says:

====================
net: Remove uses of kmap_atomic()

kmap_atomic() is being deprecated. This little series replaces the last
few uses of kmap_atomic() in the networking subsystem.

This series triggered a suggestion [1] that perhaps the Sun Cassini,
LDOM Virtual Switch Driver and the LDOM virtual network drivers should be
removed completely. I plan to do this in a follow up patchset. For
completeness, this series still includes kmap_atomic() conversions that
apply to the above referenced drivers. If for some reason we choose to not
remove these drivers, at least they won't be using kmap_atomic() anymore.

Also, the following maintainer entries for the Chelsio driver seem to be
defunct:

  Vinay Kumar Yadav <vinay.yadav@chelsio.com>
  Rohit Maheshwari <rohitm@chelsio.com>

I can submit a follow up patch to remove these entries, but thought
maybe the folks over at Chelsio would want to look into this first.

Changes v1 -> v2:
  Use memcpy_from_page() in patches 2/6 and 4/6
  Add new patch for the thunderbolt driver
  Update commit messages and cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

kmap_atomic() is being deprecated in favor of kmap_local_page(). Replace
kmap_atomic() and kunmap_atomic() with kmap_local_page() and kunmap_local()
respectively.

Note that kmap_atomic() disables preemption and page-fault processing, but
kmap_local_page() doesn't. When converting uses of kmap_atomic(), one has
to check if the code being executed between the map/unmap implicitly
depends on page-faults and/or preemption being disabled. If yes, then code
to disable page-faults and/or preemption should also be added for
functional correctness. That however doesn't appear to be the case here,
so just kmap_local_page() is used.

Also note that the page being mapped is not allocated by the driver, and so
the driver doesn't know if the page is in normal memory. This is the reason
kmap_local_page() is used as opposed to page_address().

I don't have hardware, so this change has only been compile tested.

Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kmap_atomic() is being deprecated in favor of kmap_local_page(). Replace
kmap_atomic() and kunmap_atomic() with kmap_local_page() and kunmap_local()
respectively.

Note that kmap_atomic() disables preemption and page-fault processing, but
kmap_local_page() doesn't. When converting uses of kmap_atomic(), one has
to check if the code being executed between the map/unmap implicitly
depends on page-faults and/or preemption being disabled. If yes, then code
to disable page-faults and/or preemption should also be added for
functional correctness. That however doesn't appear to be the case here,
so just kmap_local_page() is used.

Also note that the page being mapped is not allocated by the driver, and so
the driver doesn't know if the page is in normal memory. This is the reason
kmap_local_page() is used as opposed to page_address().

I don't have hardware, so this change has only been compile tested.

Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kmap_atomic() is being deprecated in favor of kmap_local_page(). Replace
the map-memcpy-unmap usage pattern (done using k[un]map_atomic()) with
memcpy_from_page(), which internally uses kmap_local_page() and
kunmap_local(). This renders the variable 'vaddr' unnecessary, and so
remove this too.

Note that kmap_atomic() disables preemption and page-fault processing, but
kmap_local_page() doesn't. When converting uses of kmap_atomic(), one has
to check if the code being executed between the map/unmap implicitly
depends on page-faults and/or preemption being disabled. If yes, then code
to disable page-faults and/or preemption should also be added for
functional correctness. That however doesn't appear to be the case here,
so just memcpy_from_page() is used.

Also note that the page being mapped is not allocated by the driver, and so
the driver doesn't know if the page is in normal memory. This is the reason
kmap_local_page() is used (via memcpy_from_page()) as opposed to
page_address().

I don't have hardware, so this change has only been compile tested.

Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Suggested-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pages for Rx buffers are allocated in cas_page_alloc() using either
GFP_ATOMIC or GFP_KERNEL. Memory allocated with GFP_KERNEL/GFP_ATOMIC can't
come from highmem and so there's no need to kmap() them. Just use
page_address() instead. This makes the variable 'addr' unnecessary, so
remove it too.

Note that kmap_atomic() disables preemption and page-fault processing,
but page_address() doesn't. When removing uses of kmap_atomic(), one has to
check if the code being executed between the map/unmap implicitly depends
on page-faults and/or preemption being disabled. If yes, then code to
disable page-faults and/or preemption should also be added for functional
correctness. That however doesn't appear to be the case here, so just
page_address() is used.

I don't have hardware, so this change has only been compile tested.

Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kmap_atomic() is being deprecated in favor of kmap_local_page(). Replace
kmap_atomic() and kunmap_atomic() with kmap_local_page() and kunmap_local()
respectively.

Note that kmap_atomic() disables preemption and page-fault processing, but
kmap_local_page() doesn't. When converting uses of kmap_atomic(), one has
to check if the code being executed between the map/unmap implicitly
depends on page-faults and/or preemption being disabled. If yes, then code
to disable page-faults and/or preemption should also be added for
functional correctness. That however doesn't appear to be the case here,
so just kmap_local_page() is used.

Also note that the page being mapped is not allocated by the driver, and so
the driver doesn't know if the page is in normal memory. This is the reason
kmap_local_page() is used as opposed to page_address().

I don't have hardware, so this change has only been compile tested.

Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Cc: Edward Cree <ecree.xilinx@gmail.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kmap_atomic() is being deprecated in favor of kmap_local_page(). Replace
the map-memcpy-unmap usage pattern (done using k[un]map_atomic()) with
memcpy_from_page(), which internally uses kmap_local_page() and
kunmap_local(). This renders the variables 'data' and 'vaddr' unnecessary,
and so remove these too.

Note that kmap_atomic() disables preemption and page-fault processing, but
kmap_local_page() doesn't. When converting uses of kmap_atomic(), one has
to check if the code being executed between the map/unmap implicitly
depends on page-faults and/or preemption being disabled. If yes, then code
to disable page-faults and/or preemption should also be added for
functional correctness. That however doesn't appear to be the case here,
so just memcpy_from_page() is used.

Also note that the page being mapped is not allocated by the driver, and so
the driver doesn't know if the page is in normal memory. This is the reason
kmap_local_page() is used (via memcpy_from_page()) as opposed to
page_address().

I don't have hardware, so this change has only been compile tested.

Cc: Ayush Sawal <ayush.sawal@chelsio.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Suggested-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Horatiu Vultur says:

====================
net: lan966x: Extend xdp support

Extend the current support of XDP in lan966x with the action XDP_TX and
XDP_REDIRECT.
The first patches just prepare the things such that it would be easier
to add XDP_TX and XDP_REDIRECT actions. Like adding XDP_PACKET_HEADROOM,
introduce helper functions, use the correct dma_dir for the page pool
The last 2 patches introduce the XDP actions XDP_TX and XDP_REDIRECT.

v4->v5:
- add iterator declaration inside for loops
- move the scope of port inside the function lan966x_fdma_rx_alloc_page_pool
- create union for skb and xdpf inside struct lan966x_tx_dcb_buf

v3->v4:
- use napi_consume_skb instead of dev_kfree_skb_any
- arrange members in struct lan966x_tx_dcb_buf not to have holes
- fix when xdp program is added the check for determining if page pool
  needs to be recreated was wrong
- change type for len in lan966x_tx_dcb_buf to u32

v2->v3:
- make sure to update rxq memory model
- update the page pool direction if there is any xdp program
- in case of action XDP_TX give back to reuse the page
- in case of action XDP_REDIRECT, remap the frame and make sure to
  unmap it when is transmitted.

v1->v2:
- use skb_reserve of using skb_put and skb_pull
- make sure that data_len doesn't include XDP_PACKET_HEADROOM
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend lan966x XDP support with the action XDP_REDIRECT. This is similar
with the XDP_TX, so a lot of functionality can be reused.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend lan966x XDP support with the action XDP_TX. In this case when the
received buffer needs to execute XDP_TX, the buffer will be moved to the
TX buffers. So a new RX buffer will be allocated.
When the TX finish with the frame, it would give back the buffer to the
page pool.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To add support for XDP_TX it is required to be able to write to the DMA
area therefore it is required that the pages will be mapped using
DMA_BIDIRECTIONAL flag.
Therefore check if there are any xdp programs on the interfaces and in
that case set DMA_BIDRECTIONAL otherwise use DMA_FROM_DEVICE.
Therefore when a new XDP program is added it is required to redo the
page_pool.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By default the rxq memory model is MEM_TYPE_PAGE_SHARED but to be able
to reuse pages on the TX side, when the XDP action XDP_TX it is required
to update the memory model to PAGE_POOL.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when a frame was transmitted, it is required to unamp the
frame that was transmitted. The length of the frame was taken from the
transmitted skb. In the future we might not have an skb, therefore store
the length skb directly in the lan966x_tx_dcb_buf and use this one to
unamp the frame.
While at this, also arrange the members in lan966x_tx_dcb_buf not to
have any holes.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce lan966x_fdma_tx_setup_dcb and lan966x_fdma_tx_start functions
and use of them inside lan966x_fdma_xmit. There is no functional change
in here.
They are introduced to be used when XDP_TX/REDIRECT actions are
introduced.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the page_pool params to allocate XDP_PACKET_HEADROOM space as
headroom for all received frames.
This is needed for when the XDP_TX and XDP_REDIRECT are implemented.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PEROUT_ENABLE_OUTPUT_MASK was there to allow us to enable/disable
all the perout pins. But it is not standard procedure, we will
have to discard it.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

82P33 family of chips can trigger TOD read/write by external
signal from one of the IN12/13/14 pins, which are set user
space programs by calling PTP_PIN_SETFUNC through ptp_ioctl
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steen Hegelund says:

====================
net: TC protocol all support in Sparx5 IS2 VCAP

This provides support for the TC flower filters 'protocol all' clause in
the Sparx5 IS2 VCAP.

It builds on top of the initial IS2 VCAP support found in these series:

https://lore.kernel.org/all/20221020130904.1215072-1-steen.hegelund@microchip.com/
https://lore.kernel.org/all/20221109114116.3612477-1-steen.hegelund@microchip.com/
https://lore.kernel.org/all/20221111130519.1459549-1-steen.hegelund@microchip.com/
https://lore.kernel.org/all/20221117213114.699375-1-steen.hegelund@microchip.com/

Functionality:
==============

As the configuration for the Sparx5 IS2 VCAP consists of one (or more)
keyset(s) for each lookup/port per traffic classification, it is not
always possible to cover all protocols with just one ordinary VCAP rule.

To improve this situation the driver will try to find out what keysets a
rule will need to cover a TC flower "protocol all" filter and then compare
this set of keysets to what the hardware is currently configured for.

In case multiple keysets are needed then the driver can create a rule per
rule size (e.g. X6 and X12) and use a mask on the keyset type field to
allow the VCAP to match more than one keyset with just one rule.

This is possible because the keysets that have the same size typically has
many keys in common, so the VCAP rule keys can make a common match.

The result is that one TC filter command may create multiple IS2 VCAP rules
of different sizes that have a type field with a masked type id.

Delivery:
=========

This is current plan for delivering the full VCAP feature set of Sparx5:

- Sparx5 IS0 VCAP support
- TC policer and drop action support (depends on the Sparx5 QoS support
  upstreamed separately)
- Sparx5 ES0 VCAP support
- TC flower template support
- TC matchall filter support for mirroring and policing ports
- TC flower filter mirror action support
- Sparx5 ES2 VCAP support

Version History:
================
v2      Fixed a NULL return value compiler warning.
        Moved the new vcap_find_actionfield function a bit up in the file.

v1      Initial version
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This tests the filtering of keys, either dropping unsupported keys or
dropping keys specified in a list.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will display a list of keyset in case the type_id field in the VCAP
rule has been wildcarded.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows support of TC protocol all for the Sparx5 IS2 VCAP.

This is done by creating multiple rules that covers the rule size and
traffic types in the IS2.
Each rule size (e.g X16 and X6) may have multiple keysets and if there are
more than one the type field in the VCAP rule will be wildcarded to support
these keysets.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for making a copy of a rule and modify keys and actions
to differentiate the copy.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Variable 'insert_retries' is not effectively used in the function, so
delete it.

lib/test_rhashtable.c:437:18: warning: variable 'insert_retries' set but not used.

Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3242Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the open-code with sysfs_streq().
Signed-off-by: Xu Panda <xu.panda@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We added patch for motorcomm.c to support YT8531S. This patch has
been tested on AM335x platform which has one YT8531S interface
card and passed all test cases.
The tested cases indluding: YT8531S UTP function with support of
10M/100M/1000M; YT8531S Fiber function with support of 100M/1000M;
and YT8531S Combo function that supports auto detection of media type.

Since most functions of YT8531S are similar to YT8521 and we reuse some
codes for YT8521 in the patch file.
Signed-off-by: Frank <Frank.Sae@motor-comm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>