- 14 Oct, 2022 1 commit
-
-
AngeloGioacchino Del Regno authored
Since commit 262ca38f ("clk: Stop forwarding clk_rate_requests to the parent"), the clk_rate_request is .. as the title says, not forwarded anymore to the parent: this produces an issue with the MediaTek clock MUX driver during GPU DVFS on MT8195, but not on MT8192 or others. This is because, differently from others, like MT8192 where all of the clocks in the MFG parents tree are of mtk_mux type, but in the parent tree of MT8195's MFG clock, we have one mtk_mux clock and one (clk framework generic) mux clock, like so: names: mfg_bg3d -> mfg_ck_fast_ref -> top_mfg_core_tmp (or) mfgpll types: mtk_gate -> mux -> mtk_mux (or) mtk_pll To solve this issue and also keep the GPU DVFS clocks code working as expected, wire up a .determine_rate() callback for the mtk_mux ops; for that, the standard clk_mux_determine_rate_flags() was used as it was possible to. This commit was successfully tested on MT6795 Xperia M5, MT8173 Elm, MT8192 Spherion and MT8195 Tomato; no regressions were seen. For the sake of some more documentation about this issue here's the trace of it: [ 12.211587] ------------[ cut here ]------------ [ 12.211589] WARNING: CPU: 6 PID: 78 at drivers/clk/clk.c:1462 clk_core_init_rate_req+0x84/0x90 [ 12.211593] Modules linked in: stp crct10dif_ce mtk_adsp_common llc rfkill snd_sof_xtensa_dsp panfrost(+) sbs_battery cros_ec_lid_angle cros_ec_sensors snd_sof_of cros_ec_sensors_core hid_multitouch cros_usbpd_logger snd_sof gpu_sched snd_sof_utils fuse ipv6 [ 12.211614] CPU: 6 PID: 78 Comm: kworker/u16:2 Tainted: G W 6.0.0-next-20221011+ #58 [ 12.211616] Hardware name: Acer Tomato (rev2) board (DT) [ 12.211617] Workqueue: devfreq_wq devfreq_monitor [ 12.211620] pstate: 40400009 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 12.211622] pc : clk_core_init_rate_req+0x84/0x90 [ 12.211625] lr : clk_core_forward_rate_req+0xa4/0xe4 [ 12.211627] sp : ffff80000893b8e0 [ 12.211628] x29: ffff80000893b8e0 x28: ffffdddf92f9b000 x27: ffff46a2c0e8bc05 [ 12.211632] x26: ffff46a2c1041200 x25: 0000000000000000 x24: 00000000173eed80 [ 12.211636] x23: ffff80000893b9c0 x22: ffff80000893b940 x21: 0000000000000000 [ 12.211641] x20: ffff46a2c1039f00 x19: ffff46a2c1039f00 x18: 0000000000000000 [ 12.211645] x17: 0000000000000038 x16: 000000000000d904 x15: 0000000000000003 [ 12.211649] x14: ffffdddf9357ce48 x13: ffffdddf935e71c8 x12: 000000000004803c [ 12.211653] x11: 00000000a867d7ad x10: 00000000a867d7ad x9 : ffffdddf90c28df4 [ 12.211657] x8 : ffffdddf9357a980 x7 : 0000000000000000 x6 : 0000000000000004 [ 12.211661] x5 : ffffffffffffffc8 x4 : 00000000173eed80 x3 : ffff80000893b940 [ 12.211665] x2 : 00000000173eed80 x1 : ffff80000893b940 x0 : 0000000000000000 [ 12.211669] Call trace: [ 12.211670] clk_core_init_rate_req+0x84/0x90 [ 12.211673] clk_core_round_rate_nolock+0xe8/0x10c [ 12.211675] clk_mux_determine_rate_flags+0x174/0x1f0 [ 12.211677] clk_mux_determine_rate+0x1c/0x30 [ 12.211680] clk_core_determine_round_nolock+0x74/0x130 [ 12.211682] clk_core_round_rate_nolock+0x58/0x10c [ 12.211684] clk_core_round_rate_nolock+0xf4/0x10c [ 12.211686] clk_core_set_rate_nolock+0x194/0x2ac [ 12.211688] clk_set_rate+0x40/0x94 [ 12.211691] _opp_config_clk_single+0x38/0xa0 [ 12.211693] _set_opp+0x1b0/0x500 [ 12.211695] dev_pm_opp_set_rate+0x120/0x290 [ 12.211697] panfrost_devfreq_target+0x3c/0x50 [panfrost] [ 12.211705] devfreq_set_target+0x8c/0x2d0 [ 12.211707] devfreq_update_target+0xcc/0xf4 [ 12.211708] devfreq_monitor+0x40/0x1d0 [ 12.211710] process_one_work+0x294/0x664 [ 12.211712] worker_thread+0x7c/0x45c [ 12.211713] kthread+0x104/0x110 [ 12.211716] ret_from_fork+0x10/0x20 [ 12.211718] irq event stamp: 7102 [ 12.211719] hardirqs last enabled at (7101): [<ffffdddf904ea5a0>] finish_task_switch.isra.0+0xec/0x2f0 [ 12.211723] hardirqs last disabled at (7102): [<ffffdddf91794b74>] el1_dbg+0x24/0x90 [ 12.211726] softirqs last enabled at (6716): [<ffffdddf90410be4>] __do_softirq+0x414/0x588 [ 12.211728] softirqs last disabled at (6507): [<ffffdddf904171d8>] ____do_softirq+0x18/0x24 [ 12.211730] ---[ end trace 0000000000000000 ]--- Fixes: 262ca38f ("clk: Stop forwarding clk_rate_requests to the parent") Signed-off-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20221011135548.318323-1-angelogioacchino.delregno@collabora.comSigned-off-by:
Stephen Boyd <sboyd@kernel.org>
-
- 11 Oct, 2022 2 commits
-
-
Maxime Ripard authored
We're recently encountered a regression due to the rates reported through the clk_notifier_data being off when changing parents. Let's add a test suite and a test to make sure that we do get notified and with the proper rates. Suggested-by:
Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20221010-rpi-clk-fixes-again-v1-2-d87ba82ac404@cerno.techTested-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Maxime Ripard authored
Commit cb1b1dd9 ("clk: Set req_rate on reparenting") introduced a new function, clk_core_update_orphan_child_rates(), that updates the req_rate field on reparenting. It turns out that that function will interfere with the clock notifying done by __clk_recalc_rates(). This ends up reporting the new rate in both the old_rate and new_rate fields of struct clk_notifier_data. Since clk_core_update_orphan_child_rates() is basically __clk_recalc_rates() without the notifiers, and with the req_rate field update, we can drop clk_core_update_orphan_child_rates() entirely, and make __clk_recalc_rates() update req_rate. However, __clk_recalc_rates() is being called in several code paths: when retrieving a rate (most likely through clk_get_rate()), when changing parents (through clk_set_rate() or clk_hw_reparent()), or when updating the orphan status (through clk_core_reparent_orphans_nolock(), called at registration). Updating req_rate on reparenting or initialisation makes sense, but we shouldn't do it on clk_get_rate(). Thus an extra flag has been added to update or not req_rate depending on the context. Fixes: cb1b1dd9 ("clk: Set req_rate on reparenting") Link: https://lore.kernel.org/linux-clk/0acc7217-762c-7c0d-45a0-55c384824ce4@samsung.com/ Link: https://lore.kernel.org/linux-clk/Y0QNSx+ZgqKSvPOC@sirena.org.uk/Reported-by:
Mark Brown <broonie@kernel.org> Suggested-by:
-
- 15 Sep, 2022 25 commits
-
-
Maxime Ripard authored
Let's add a test on the rate range after a reparenting. This fails for now, but it's worth having it to document the corner cases we don't support yet. Signed-off-by:
Naresh Kamboju <naresh.kamboju@linaro.org> Tested-by:
Linux Kernel Functional Testing <lkft@linaro.org> Signed-off-by:
-
Maxime Ripard authored
The gfx3d clock is hand-crafting its own clk_rate_request in clk_gfx3d_determine_rate to pass to the parent of that clock. However, since the clk_rate_request is zero'd at creation, it will have a max_rate of 0 which will break any code depending on the clock boundaries. That includes the recent commit 948fb096 ("clk: Always clamp the rounded rate") which will clamp the rate given to clk_round_rate() to the current clock boundaries. For the gfx3d clock, it means that since both the min_rate and max_rate fields are set at zero, clk_round_rate() now always return 0. Let's initialize the min_rate and max_rate fields properly for that clock. Fixes: 948fb096 ("clk: Always clamp the rounded rate") Signed-off-by:
-
Maxime Ripard authored
Some clock providers are hand-crafting their clk_rate_request, and need to figure out the current boundaries of their clk_hw to fill it properly. Let's create such a function for clock providers. Signed-off-by:
-
Maxime Ripard authored
In order to make sure we don't carry anything over from an already existing clk_rate_request pointer we would pass to clk_core_init_rate_req(), let's zero the entire structure before initializing it. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
If the clock cannot modify its rate and has CLK_SET_RATE_PARENT, clk_mux_determine_rate_flags(), clk_core_round_rate_nolock() and a number of drivers will forward the clk_rate_request to the parent clock. clk_core_round_rate_nolock() will pass the pointer directly, which means that we pass a clk_rate_request to the parent that has the rate, min_rate and max_rate of the child, and the best_parent_rate and best_parent_hw fields will be relative to the child as well, so will point to our current clock and its rate. The most common case for CLK_SET_RATE_PARENT is that the child and parent clock rates will be equal, so the rate field isn't a worry, but the other fields are. Similarly, if the parent clock driver ever modifies the best_parent_rate or best_parent_hw, this will be applied to the child once the call to clk_core_round_rate_nolock() is done. best_parent_hw is probably not going to be a valid parent, and best_parent_rate might lead to a parent rate change different to the one that was initially computed. clk_mux_determine_rate_flags() and the affected drivers will copy the request before forwarding it to the parents, so they won't be affected by the latter issue, but the former is still going to be there and will lead to erroneous data and context being passed to the various clock drivers in the same sub-tree. Let's create two new functions, clk_core_forward_rate_req() and clk_hw_forward_rate_request() for the framework and the clock providers that will copy a request from a child clock and update the context to match the parent's. We also update the relevant call sites in the framework and drivers to use that new function. Let's also add a test to make sure we avoid regressions there. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
clk_has_parent() doesn't modify the clocks being passed, so let's make it const. Suggested-by:
-
Maxime Ripard authored
We will need to know if a clk_core pointer has a given parent in other functions, so let's create a clk_core_has_parent() function that clk_has_parent() will call into. For good measure, let's add some unit tests as well to make sure it works properly. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
clk_mux_determine_rate_flags() will call into __clk_determine_rate() with a clk_hw pointer, while it has access to the clk_core pointer already. This leads to back and forth between clk_hw and clk_core, while __clk_determine_rate will only call clk_core_round_rate_nolock() with the clk_core pointer it retrieved from the clk_hw. Let's simplify things a bit by calling into clk_core_round_rate_nolock directly. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
The expectation is that a new clk_rate_request is initialized through a call to clk_core_init_rate_req(). However, at the moment it only fills the parent rate and clk_hw pointer, but omits the other fields such as the clock rate boundaries. Some users of that function will update them after calling it, but most don't. As we are passed the clk_core pointer, we have access to those boundaries in clk_core_init_rate_req() however, so let's just fill it there and remove it from the few callers that do it right. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
clk-divider instantiates clk_rate_request internally for its round_rate implementations to share the code with its determine_rate implementations. However, it's missing a few fields (min_rate, max_rate) that would be initialized properly if it was using clk_core_init_rate_req(). Let's create the clk_hw_init_rate_request() function for clock providers to be able to share the code to instation clk_rate_requests with the framework. This will also be useful for some tests introduced in later patches. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
The clk_rate_request structure is used internally as an argument for the clk_core_determine_round_nolock() and clk_core_round_rate_nolock(). In both cases, the clk_core_init_rate_req() function is used to initialize the clk_rate_request structure. However, the expectation on who gets to call that function is inconsistent between those two functions. Indeed, clk_core_determine_round_nolock() will assume the structure is properly initialized and will just use it. On the other hand, clk_core_round_rate_nolock() will call clk_core_init_rate_req() itself, expecting the caller to have filled only a minimal set of parameters (rate, min_rate and max_rate). If we ignore the calling convention inconsistency, this leads to a second inconsistency for drivers: * If they get called by the framework through clk_core_round_rate_nolock(), the rate, min_rate and max_rate fields will be filled by the caller, and the best_parent_rate and best_parent_hw fields will get filled by clk_core_init_rate_req(). * If they get called by a driver through __clk_determine_rate (and thus clk_core_round_rate_nolock), only best_parent_rate and best_parent_hw are being explicitly set by the framework. Even though we can reasonably expect rate to be set, only one of the 6 in-tree users explicitly set min_rate and max_rate. * If they get called by the framework through clk_core_determine_round_nolock(), then we have two callpaths. Either it will be called by clk_core_round_rate_nolock() itself, or it will be called by clk_calc_new_rates(), which will properly initialize rate, min_rate, max_rate itself, and best_parent_rate and best_parent_hw through clk_core_init_rate_req(). Even though the first and third case seems equivalent, they aren't when the clock has CLK_SET_RATE_PARENT. Indeed, in such a case clk_core_round_rate_nolock() will call itself on the current parent clock with the same clk_rate_request structure. The clk_core_init_rate_req() function will then be called on the parent clock, with the child clk_rate_request pointer and will fill the best_parent_rate and best_parent_hw fields with the parent context. When the whole recursion stops and the call returns, the initial caller will end up with a clk_rate_request structure with some information of the child clock (rate, min_rate, max_rate) and some others of the last clock up the tree whose child had CLK_SET_RATE_PARENT (best_parent_hw, best_parent_rate). In the most common case, best_parent_rate is going to be equal on all the parent clocks so it's not a big deal. However, best_parent_hw is going to point to a clock that never has been a valid parent for that clock which is definitely confusing. In order to fix the calling inconsistency, let's move the clk_core_init_rate_req() calls to the callers, which will also help a bit with the clk_core_round_rate_nolock() recursion. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by: -
Maxime Ripard authored
The expectation is that a clk_rate_request structure is supposed to be initialized using clk_core_init_rate_req(), yet the rate we want to request still needs to be set by hand. Let's just pass the rate as a function argument so that callers don't have any extra work to do. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
If a non-rate clock started by default with a parent that never registered, core->req_rate will be 0. The expectation is that whenever the parent will be registered, req_rate will be updated with the new value that has just been computed. However, if that clock is a mux, clk_set_parent() can also make that clock no longer orphan. In this case however, we never update req_rate. The natural solution to this would be to update core->rate and core->req_rate in clk_reparent() by calling clk_recalc(). However, this doesn't work in all cases. Indeed, clk_recalc() is called by __clk_set_parent_before(), __clk_set_parent() and clk_core_reparent(). Both __clk_set_parent_before() and __clk_set_parent will call clk_recalc() with the enable_lock taken through a call to clk_enable_lock(), the underlying locking primitive being a spinlock. clk_recalc() calls the backing driver .recalc_rate hook, and that implementation might sleep if the underlying device uses a bus with accesses that might sleep, such as i2c. In such a situation, we would end up sleeping while holding a spinlock, and thus in an atomic section. In order to work around this, we can move the core->rate and core->req_rate update to the clk_recalc() calling sites, after the enable_lock has been released if it was taken. The only situation that could still be problematic is the clk_core_reparent() -> clk_reparent() case that doesn't have any locking. clk_core_reparent() is itself called by clk_hw_reparent(), which is then called by 4 drivers: * clk-stm32mp1.c, stm32/clk-stm32-core.c and tegra/clk-tegra210-emc.c use it in their set_parent implementation. The set_parent hook is only called by __clk_set_parent() and clk_change_rate(), both of them calling it without the enable_lock taken. * clk/tegra/clk-tegra124-emc.c calls it as part of its set_rate implementation. set_rate is only called by clk_change_rate(), again without the enable_lock taken. In both cases we can't end up in a situation where the clk_hw_reparent() caller would hold a spinlock, so it seems like this is a good workaround. Let's also add some unit tests to make sure we cover the original bug. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by: -
Maxime Ripard authored
clk_set_rate_range() will use the last requested rate for the clock when it calls into the driver set_rate hook. However, if CLK_GET_RATE_NOCACHE is set on that clock, the last requested rate might not be matching the current rate of the clock. In such a case, let's read out the rate from the hardware and use that in our set_rate instead. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
Let's leverage the dummy mux with multiple parents we have to create a mux whose default parent will never be registered, and thus will always be orphan by default. We can then create some tests to make sure that the clock API behaves properly in such a case, and that the transition to a non-orphan clock when we change the parent is done properly. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
We'll need to test a few corner cases that occur when we have a mux clock whose default parent is missing. For now, let's create the context structure and the trivial ops, along with a test suite that just tests trivial things for now, without considering the orphan case. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
We have a few tests for a mux with a single parent, testing the case where it used to be orphan. Let's leverage most of the code but register the clock properly to test a few trivial things. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
The clock framework supports clocks that can have their rate changed without the kernel knowing about it using the CLK_GET_RATE_NOCACHE flag. As its name suggests, this flag turns off the rate caching in the clock framework, reading out the rate from the hardware any time we need to read it. Let's add a couple of tests to make sure it works as intended. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
Some more context might be useful for unit-tests covering a previously reported bug, so let's add a link to the discussion for that bug. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
We start to have a few test suites, and we'll add more, so it will get pretty confusing to figure out what is supposed to be tested in what suite. Let's add some comments to explain what setup they create, and what we should be testing in every suite. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
As shown by a number of clock users already, clk_get_rate() can be called whether or not the clock is enabled. Similarly, a number of clock drivers will return a rate of 0 whenever the rate cannot be figured out. Since it was a bit ambiguous before, let's make it clear in the clk_get_rate() documentation. Signed-off-by:
-
Maxime Ripard authored
Multiple platforms (amlogic, imx8) return 0 when the clock rate cannot be determined properly by the recalc_rate hook. Mention in the documentation that the framework is ok with that. Signed-off-by:
-
Maxime Ripard authored
Commit 948fb096 ("clk: Always clamp the rounded rate") recently started to clamp the request rate in the clk_rate_request passed as an argument of clk_core_determine_round_nolock() with the min_rate and max_rate fields of that same request. While the clk_rate_requests created by the framework itself always have those fields set, some drivers will create it themselves and don't always fill min_rate and max_rate. In such a case, we end up clamping the rate with a minimum and maximum of 0, thus always rounding the rate to 0. Let's skip the clamping if both min_rate and max_rate are set to 0 and complain so that it gets fixed. Fixes: 948fb096 ("clk: Always clamp the rounded rate") Signed-off-by:
-
Maxime Ripard authored
When clk_put() is called we don't make another clk_set_rate() call to re-evaluate the rate boundaries. This is unlike clk_set_rate_range() that evaluates the rate again each time it is called. However, clk_put() is essentially equivalent to clk_set_rate_range() since after clk_put() completes the consumer's boundaries shouldn't be enforced anymore. Let's add a call to clk_set_rate_range() in clk_put() to make sure those rate boundaries are dropped and the clock provider drivers can react. In order to be as non-intrusive as possible, we'll just make that call if the clock had non-default boundaries. Also add a few tests to make sure this case is covered. Fixes: c80ac50c ("clk: Always set the rate on clk_set_range_rate") Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mp Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> # exynos4210, meson g12b Signed-off-by:
-
Maxime Ripard authored
Following the clk_hw->clk pointer is equivalent to calling clk_hw_get_clk(), but will make the job harder if we need to rework that part in the future. Signed-off-by:
-
- 14 Aug, 2022 10 commits
-
-
Linus Torvalds authored
-
Yury Norov authored
Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we have gfp_types.h for this. Fixes powerpc allmodconfig build: In file included from include/linux/nodemask.h:97, from include/linux/mmzone.h:17, from include/linux/gfp.h:7, from include/linux/radix-tree.h:12, from include/linux/idr.h:15, from include/linux/kernfs.h:12, from include/linux/sysfs.h:16, from include/linux/kobject.h:20, from include/linux/pci.h:35, from arch/powerpc/kernel/prom_init.c:24: include/linux/random.h: In function 'add_latent_entropy': >> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'? 25 | add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy)); | ^~~~~~~~~~~~~~ | add_latent_entropy include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in Reported-by:kernel test robot <lkp@intel.com> CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com> CC: Andrew Morton <akpm@linux-foundation.org> CC: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by:
Yury Norov <yury.norov@gmail.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull vfs lseek fix from Al Viro: "Fix proc_reg_llseek() breakage. Always had been possible if somebody left NULL ->proc_lseek, became a practical issue now" * tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: take care to handle NULL ->proc_lseek()
-
Al Viro authored
Easily done now, just by clearing FMODE_LSEEK in ->f_mode during proc_reg_open() for such entries. Fixes: 868941b1 "fs: remove no_llseek" Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk>
-
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tipLinus Torvalds authored
Pull more xen updates from Juergen Gross: - fix the handling of the "persistent grants" feature negotiation between Xen blkfront and Xen blkback drivers - a cleanup of xen.config and adding xen.config to Xen section in MAINTAINERS - support HVMOP_set_evtchn_upcall_vector, which is more compliant to "normal" interrupt handling than the global callback used up to now - further small cleanups * tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections xen: remove XEN_SCRUB_PAGES in xen.config xen/pciback: Fix comment typo xen/xenbus: fix return type in xenbus_file_read() xen-blkfront: Apply 'feature_persistent' parameter when connect xen-blkback: Apply 'feature_persistent' parameter when connect xen-blkback: fix persistent grants negotiation x86/xen: Add support for HVMOP_set_evtchn_upcall_vector
-
Linus Torvalds authored
Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux Pull more perf tool updates from Arnaldo Carvalho de Melo: - 'perf c2c' now supports ARM64, adjust its output to cope with differences with what is in x86_64. Now go find false sharing on ARM64 (at least Neoverse) as well! - Refactor the JSON processing, making the output more compact and thus reducing the size of the resulting perf binary - Improvements for 'perf offcpu' profiling, including tracking child processes - Update Intel JSON metrics and events files for broadwellde, broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown, knightslanding, sapphirerapids, skylakex and snowridgex - Add 'perf stat' JSON output and a 'perf test' entry for it - Ignore memfd and anonymous mmap events if jitdump present - Refactor 'perf test' shell tests allowing subdirs - Fix an error handling path in 'parse_perf_probe_command()' - Fixes for the guest Intel PT tracing patchkit in the 1st batch of this merge window - Print debuginfod queries if -v option is used, to explain delays in processing when debuginfo servers are enabled to fetch DSOs with richer symbol tables - Improve error message for 'perf record -p not_existing_pid' - Fix openssl and libbpf feature detection - Add PMU pai_crypto event description for IBM z16 on 'perf list' - Fix typos and duplicated words on comments in various places * tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits) perf test: Refactor shell tests allowing subdirs perf vendor events: Update events for snowridgex perf vendor events: Update events and metrics for skylakex perf vendor events: Update metrics for sapphirerapids perf vendor events: Update events for knightslanding perf vendor events: Update metrics for jaketown perf vendor events: Update metrics for ivytown perf vendor events: Update events and metrics for icelakex perf vendor events: Update events and metrics for haswellx perf vendor events: Update events and metrics for cascadelakex perf vendor events: Update events and metrics for broadwellx perf vendor events: Update metrics for broadwellde perf jevents: Fold strings optimization perf jevents: Compress the pmu_events_table perf metrics: Copy entire pmu_event in find metric perf pmu-events: Hide the pmu_events perf pmu-events: Don't assume pmu_event is an array perf pmu-events: Move test events/metrics to JSON perf test: Use full metric resolution perf pmu-events: Hide pmu_events_map ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Michael Ellerman: - Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit CPUs trap on it rather than ignoring it as they should. - Fix ftrace when building with clang, which was broken by some refactoring. - A couple of other minor fixes. Thanks to Christophe Leroy, Naveen N. Rao, Nick Desaulniers, Ondrej Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool. * tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/kexec: Fix build failure from uninitialised variable powerpc/ppc-opcode: Fix PPC_RAW_TW() powerpc64/ftrace: Fix ftrace for clang builds powerpc: Make eh value more explicit when using lwarx powerpc: Don't hide eh field of lwarx behind a macro powerpc: Fix eh field when calling lwarx on PPC32
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull /proc/mounts fix from Al Viro: "Fix for /proc/mounts escaping - escape the '#' character too" * tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: vfs: escape hash as well
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull more cifs updates from Steve French: - two fixes for stable, one for a lock length miscalculation, and another fixes a lease break timeout bug - improvement to handle leases, allows the close timeout to be configured more safely - five restructuring/cleanup patches * tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: cifs: Do not access tcon->cfids->cfid directly from is_path_accessible cifs: Add constructor/destructors for tcon->cfid SMB3: fix lease break timeout when multiple deferred close handles for the same file. smb3: allow deferred close timeout to be configurable cifs: Do not use tcon->cfid directly, use the cfid we get from open_cached_dir cifs: Move cached-dir functions into a separate file cifs: Remove {cifs,nfs}_fscache_release_page() cifs: fix lock length calculation
-
David Howells authored
Enable multipage folio support for the afs filesystem. Support has already been implemented in netfslib, fscache and cachefiles and in most of afs, but I've waited for Matthew Wilcox's latest folio changes. Note that it does require a change to afs_write_begin() to return the correct subpage. This is a "temporary" change as we're working on getting rid of the need for ->write_begin() and ->write_end() completely, at least as far as network filesystems are concerned - but it doesn't prevent afs from making use of the capability. Signed-off-by:
David Howells <dhowells@redhat.com> Acked-by:
Matthew Wilcox (Oracle) <willy@infradead.org> Tested-by: kafs-testing@auristor.com Cc: Marc Dionne <marc.dionne@auristor.com> Cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/lkml/2274528.1645833226@warthog.procyon.org.uk/Signed-off-by:
-
- 13 Aug, 2022 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Ingo Molnar: "Misc timer fixes: - fix a potential use-after-free bug in posix timers - correct a prototype - address a build warning" * tag 'timers-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: posix-cpu-timers: Cleanup CPU timers before freeing them during exec time: Correct the prototype of ns_to_kernel_old_timeval and ns_to_timespec64 posix-timers: Make do_clock_gettime() static
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fix from Ingo Molnar: "Fix the 'IBPB mitigated RETBleed' mode of operation on AMD CPUs (not turned on by default), which also need STIBP enabled (if available) to be '100% safe' on even the shortest speculation windows" * tag 'x86-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/bugs: Enable STIBP for IBPB mitigated RETBleed
-
