Document the t7xx devlink commands usage for fw flashing &
coredump collection.

Refer to t7xx.rst file for details.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch brings-in support for t7xx wwan device firmware flashing &
coredump collection using devlink.

Driver Registers with Devlink framework.
Implements devlink ops flash_update callback that programs modem firmware.
Creates region & snapshot required for device coredump log collection.
On early detection of wwan device in fastboot mode driver sets up CLDMA0 HW
tx/rx queues for raw data transfer then registers with devlink framework.
Upon receiving firmware image & partition details driver sends fastboot
commands for flashing the firmware.

In this flow the fastboot command & response gets exchanged between driver
and device. Once firmware flashing is success completion status is reported
to user space application.

Below is the devlink command usage for firmware flashing

$devlink dev flash pci/$BDF file ABC.img component ABC

Note: ABC.img is the firmware to be programmed to "ABC" partition.

In case of coredump collection when wwan device encounters an exception
it reboots & stays in fastboot mode for coredump collection by host driver.
On detecting exception state driver collects the core dump, creates the
devlink region & reports an event to user space application for dump
collection. The user space application invokes devlink region read command
for dump collection.

Below are the devlink commands used for coredump collection.

devlink region new pci/$BDF/mr_dump
devlink region read pci/$BDF/mr_dump snapshot $ID address $ADD length $LEN
devlink region del pci/$BDF/mr_dump snapshot $ID
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: Mishra Soumya Prakash <soumya.prakash.mishra@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI rescan module implements "rescan work queue". In firmware flashing
or coredump collection procedure WWAN device is programmed to boot in
fastboot mode and a work item is scheduled for removal & detection.
The WWAN device is reset using APCI call as part driver removal flow.
Work queue rescans pci bus at fixed interval for device detection,
later when device is detect work queue exits.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Co-developed-by: Madhusmita Sahu <madhusmita.sahu@intel.com>
Signed-off-by: Madhusmita Sahu <madhusmita.sahu@intel.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To support cases such as FW update or Core dump, the t7xx device
is capable of signaling the host that a special port needs
to be created before the handshake phase.

This patch adds the infrastructure required to create the
early ports which also requires a different configuration of
CLDMA queues.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Co-developed-by: Madhusmita Sahu <madhusmita.sahu@intel.com>
Signed-off-by: Madhusmita Sahu <madhusmita.sahu@intel.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Signed-off-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The t7xx device contains two Cross Layer DMA (CLDMA) interfaces to
communicate with AP and Modem processors respectively. So far only
MD-CLDMA was being used, this patch enables AP-CLDMA.

Rename small Application Processor (sAP) to AP.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Co-developed-by: Madhusmita Sahu <madhusmita.sahu@intel.com>
Signed-off-by: Madhusmita Sahu <madhusmita.sahu@intel.com>
Signed-off-by: Moises Veleta <moises.veleta@linux.intel.com>
Signed-off-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the suspend/resume procedure for the Broadcom AC131 and BCM5241 type
of PHYs (10/100 only) by entering the standard power down followed by the
proprietary standby mode in the auxiliary mode 4 shadow register. On resume,
the PHY software reset is enough to make it come out of standby mode so we can
utilize brcm_fet_config_init() as the resume hook.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

t-queue

Tony Nguyen says:

====================
ice: detect and report PTP timestamp issues

Jacob Keller says:

This series fixes a few small issues with the cached PTP Hardware Clock
timestamp used for timestamp extension. It also introduces extra checks to
help detect issues with this logic, such as if the cached timestamp is not
updated within the 2 second window.

This introduces a few statistics similar to the ones already available in
other Intel drivers, including tx_hwtstamp_skipped and tx_hwtstamp_timeouts.

It is intended to aid in debugging issues we're seeing with some setups
which might be related to incorrect cached timestamp values.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of the hardcoded TCP_TIMEOUT_INIT, this diff calls tcp_timeout_init
to initiate req->timeout like the non TFO SYN ACK case.

Tested using the following packetdrill script, on a host with a BPF
program that sets the initial connect timeout to 10ms.

`../../common/defaults.sh`

// Initialize connection
    0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
   +0 setsockopt(3, SOL_TCP, TCP_FASTOPEN, [1], 4) = 0
   +0 bind(3, ..., ...) = 0
   +0 listen(3, 1) = 0

   +0 < S 0:0(0) win 32792 <mss 1000,sackOK,FO TFO_COOKIE>
   +0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK>
   +.01 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK>
   +.02 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK>
   +.04 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK>
   +.01 < . 1:1(0) ack 1 win 32792

   +0 accept(3, ..., ...) = 4
Signed-off-by: Jie Meng <jmeng@fb.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The input parameter p is unused in qdisc_create. Delete it.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220815061023.51318-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

in-tech smart charging is now chargebyte. So update the email address
accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20220815080626.9688-2-stefan.wahren@i2se.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

in-tech smart charging is now chargebyte. So update the email address
accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220815080626.9688-1-stefan.wahren@i2se.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Return value of unregister_qdisc is unused, remove it.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220815030417.271894-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If the PTP hardware clock is adjusted, the ice driver must update the
cached PHC timestamp. This is required in order to perform timestamp
extension on the shorter timestamps captured by the PHY.

Currently, we simply call ice_ptp_update_cached_phctime in the settime and
adjtime callbacks. This has a few issues:

1) if ICE_CFG_BUSY is set because another thread is updating the Rx rings,
   we will exit with an error. This is not checked, and the functions do
   not re-schedule the update. This could leave the cached timestamp
   incorrect until the next scheduled work item execution.

2) even if we did handle an update, any currently outstanding Tx timestamp
   would be extended using the wrong cached PHC time. This would produce
   incorrect results.

To fix these issues, introduce a new ice_ptp_reset_cached_phctime function.
This function calls the ice_ptp_update_cached_phctime, and discards
outstanding Tx timestamps.

If the ice_ptp_update_cached_phctime function fails because ICE_CFG_BUSY is
set, we log a warning and schedule the thread to execute soon. The update
function is modified so that it always updates the cached copy in the PF
regardless. This ensures we have the most up to date values possible and
minimizes the risk of a packet timestamp being extended with the wrong
value.

It would be nice if we could skip reporting Rx timestamps until the cached
values are up to date. However, we can't access the Rx rings while
ICE_CFG_BUSY is set because they are actively being updated by another
thread.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

A following change is going to want to make use of ice_ptp_flush_tx_tracker
earlier in the ice_ptp.c file. To make this work, move the Tx timestamp
tracking functions higher up in the file, and pull the
ice_ptp_update_cached_timestamp function below them. This should have no
functional change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The ice driver requires a cached copy of the PHC time in order to perform
timestamp extension on Tx and Rx hardware timestamp values. This cached PHC
time must always be updated at least once every 2 seconds. Otherwise, the
math used to perform the extension would produce invalid results.

The updates are supposed to occur periodically in the PTP kthread work
item, which is scheduled to run every half second. Thus, we do not expect
an update to be delayed for so long. However, there are error conditions
which can cause the update to be delayed.

Track this situation by using jiffies to determine approximately how long
ago the last update occurred. Add a new statistic and a dev_warn when we
have failed to update the cached PHC time. This makes the error case more
obvious.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Several Intel networking drivers which support PTP track when Tx timestamps
are skipped or when they timeout without a timestamp from hardware. The
conditions which could cause these events are rare, but it can be useful to
know when and how often they occur.

Implement similar statistics for the ice driver, tx_hwtstamp_skipped,
tx_hwtstamp_timeouts, and tx_hwtstamp_flushed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

When we create new Rx rings, the cached_phctime field is zero initialized.
This could result in incorrect timestamp reporting due to the cached value
not yet being updated. Although a background task will periodically update
the cached value, ensure it matches the existing cached value in the PF
structure at ring initialization.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

When the user changes the number of queues via ethtool, the driver
allocates new rings. This allocation did not initialize tx_tstamps. This
results in the tx_tstamps field being zero (due to kcalloc allocation), and
would result in a NULL pointer dereference when attempting a transmit
timestamp on the new ring.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bluetooth, bpf, can and netfilter.

  A little larger than usual but it's all fixes, no late features. It's
  large partially because of timing, and partially because of follow ups
  to stuff that got merged a week or so before the merge window and
  wasn't as widely tested. Maybe the Bluetooth fixes are a little
  alarming so we'll address that, but the rest seems okay and not scary.

  Notably we're including a fix for the netfilter Kconfig [1], your WiFi
  warning [2] and a bluetooth fix which should unblock syzbot [3].

  Current release - regressions:

   - Bluetooth:
      - don't try to cancel uninitialized works [3]
      - L2CAP: fix use-after-free caused by l2cap_chan_put

   - tls: rx: fix device offload after recent rework

   - devlink: fix UAF on failed reload and leftover locks in mlxsw

  Current release - new code bugs:

   - netfilter:
      - flowtable: fix incorrect Kconfig dependencies [1]
      - nf_tables: fix crash when nf_trace is enabled

   - bpf:
      - use proper target btf when exporting attach_btf_obj_id
      - arm64: fixes for bpf trampoline support

   - Bluetooth:
      - ISO: unlock on error path in iso_sock_setsockopt()
      - ISO: fix info leak in iso_sock_getsockopt()
      - ISO: fix iso_sock_getsockopt for BT_DEFER_SETUP
      - ISO: fix memory corruption on iso_pinfo.base
      - ISO: fix not using the correct QoS
      - hci_conn: fix updating ISO QoS PHY

   - phy: dp83867: fix get nvmem cell fail

  Previous releases - regressions:

   - wifi: cfg80211: fix validating BSS pointers in
     __cfg80211_connect_result [2]

   - atm: bring back zatm uAPI after ATM had been removed

   - properly fix old bug making bonding ARP monitor mode not being able
     to work with software devices with lockless Tx

   - tap: fix null-deref on skb->dev in dev_parse_header_protocol

   - revert "net: usb: ax88179_178a needs FLAG_SEND_ZLP" it helps some
     devices and breaks others

   - netfilter:
      - nf_tables: many fixes rejecting cross-object linking which may
        lead to UAFs
      - nf_tables: fix null deref due to zeroed list head
      - nf_tables: validate variable length element extension

   - bgmac: fix a BUG triggered by wrong bytes_compl

   - bcmgenet: indicate MAC is in charge of PHY PM

  Previous releases - always broken:

   - bpf:
      - fix bad pointer deref in bpf_sys_bpf() injected via test infra
      - disallow non-builtin bpf programs calling the prog_run command
      - don't reinit map value in prealloc_lru_pop
      - fix UAFs during the read of map iterator fd
      - fix invalidity check for values in sk local storage map
      - reject sleepable program for non-resched map iterator

   - mptcp:
      - move subflow cleanup in mptcp_destroy_common()
      - do not queue data on closed subflows

   - virtio_net: fix memory leak inside XDP_TX with mergeable

   - vsock: fix memory leak when multiple threads try to connect()

   - rework sk_user_data sharing to prevent psock leaks

   - geneve: fix TOS inheriting for ipv4

   - tunnels & drivers: do not use RT_TOS for IPv6 flowlabel

   - phy: c45 baset1: do not skip aneg configuration if clock role is
     not specified

   - rose: avoid overflow when /proc displays timer information

   - x25: fix call timeouts in blocking connects

   - can: mcp251x: fix race condition on receive interrupt

   - can: j1939:
      - replace user-reachable WARN_ON_ONCE() with netdev_warn_once()
      - fix memory leak of skbs in j1939_session_destroy()

  Misc:

   - docs: bpf: clarify that many things are not uAPI

   - seg6: initialize induction variable to first valid array index (to
     silence clang vs objtool warning)

   - can: ems_usb: fix clang 14's -Wunaligned-access warning"

* tag 'net-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (117 commits)
  net: atm: bring back zatm uAPI
  dpaa2-eth: trace the allocated address instead of page struct
  net: add missing kdoc for struct genl_multicast_group::flags
  nfp: fix use-after-free in area_cache_get()
  MAINTAINERS: use my korg address for mt7601u
  mlxsw: minimal: Fix deadlock in ports creation
  bonding: fix reference count leak in balance-alb mode
  net: usb: qmi_wwan: Add support for Cinterion MV32
  bpf: Shut up kern_sys_bpf warning.
  net/tls: Use RCU API to access tls_ctx->netdev
  tls: rx: device: don't try to copy too much on detach
  tls: rx: device: bound the frag walk
  net_sched: cls_route: remove from list when handle is 0
  selftests: forwarding: Fix failing tests with old libnet
  net: refactor bpf_sk_reuseport_detach()
  net: fix refcount bug in sk_psock_get (2)
  selftests/bpf: Ensure sleepable program is rejected by hash map iter
  selftests/bpf: Add write tests for sk local storage map iterator
  selftests/bpf: Add tests for reading a dangling map iter fd
  bpf: Only allow sleepable program for resched-able iterator
  ...

Pull more ACPI updates from Rafael Wysocki:
 "These fix up direct references to the fwnode field in struct device
  and extend ACPI device properties support.

  Specifics:

   - Replace direct references to the fwnode field in struct device with
     dev_fwnode() and device_match_fwnode() (Andy Shevchenko)

   - Make the ACPI code handling device properties support properties
     with buffer values (Sakari Ailus)"

* tag 'acpi-5.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: property: Fix error handling in acpi_init_properties()
  ACPI: VIOT: Do not dereference fwnode in struct device
  ACPI: property: Read buffer properties as integers
  ACPI: property: Add support for parsing buffer property UUID
  ACPI: property: Unify integer value reading functions
  ACPI: property: Switch node property referencing from ifs to a switch
  ACPI: property: Move property ref argument parsing into a new function
  ACPI: property: Use acpi_object_type consistently in property ref parsing
  ACPI: property: Tie data nodes to acpi handles
  ACPI: property: Return type of acpi_add_nondev_subnodes() should be bool

Pull more iomap updates from Darrick Wong:
 "In the past 10 days or so I've not heard any ZOMG STOP style
  complaints about removing ->writepage support from gfs2 or zonefs, so
  here's the pull request removing them (and the underlying fs iomap
  support) from the kernel:

   - Remove iomap_writepage and all callers, since the mm apparently
     never called the zonefs or gfs2 writepage functions"

* tag 'iomap-6.0-merge-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: remove iomap_writepage
  zonefs: remove ->writepage
  gfs2: remove ->writepage
  gfs2: stop using generic_writepages in gfs2_ail1_start_one

Pull ceph updates from Ilya Dryomov:
 "We have a good pile of various fixes and cleanups from Xiubo, Jeff,
  Luis and others, almost exclusively in the filesystem.

  Several patches touch files outside of our normal purview to set the
  stage for bringing in Jeff's long awaited ceph+fscrypt series in the
  near future. All of them have appropriate acks and sat in linux-next
  for a while"

* tag 'ceph-for-5.20-rc1' of https://github.com/ceph/ceph-client: (27 commits)
  libceph: clean up ceph_osdc_start_request prototype
  libceph: fix ceph_pagelist_reserve() comment typo
  ceph: remove useless check for the folio
  ceph: don't truncate file in atomic_open
  ceph: make f_bsize always equal to f_frsize
  ceph: flush the dirty caps immediatelly when quota is approaching
  libceph: print fsid and epoch with osd id
  libceph: check pointer before assigned to "c->rules[]"
  ceph: don't get the inline data for new creating files
  ceph: update the auth cap when the async create req is forwarded
  ceph: make change_auth_cap_ses a global symbol
  ceph: fix incorrect old_size length in ceph_mds_request_args
  ceph: switch back to testing for NULL folio->private in ceph_dirty_folio
  ceph: call netfs_subreq_terminated with was_async == false
  ceph: convert to generic_file_llseek
  ceph: fix the incorrect comment for the ceph_mds_caps struct
  ceph: don't leak snap_rwsem in handle_cap_grant
  ceph: prevent a client from exceeding the MDS maximum xattr size
  ceph: choose auth MDS for getxattr with the Xs caps
  ceph: add session already open notify support
  ...

Pull more kvm updates from Paolo Bonzini:

 - Xen timer fixes

 - Documentation formatting fixes

 - Make rseq selftest compatible with glibc-2.35

 - Fix handling of illegal LEA reg, reg

 - Cleanup creation of debugfs entries

 - Fix steal time cache handling bug

 - Fixes for MMIO caching

 - Optimize computation of number of LBRs

 - Fix uninitialized field in guest_maxphyaddr < host_maxphyaddr path

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (26 commits)
  KVM: x86/MMU: properly format KVM_CAP_VM_DISABLE_NX_HUGE_PAGES capability table
  Documentation: KVM: extend KVM_CAP_VM_DISABLE_NX_HUGE_PAGES heading underline
  KVM: VMX: Adjust number of LBR records for PERF_CAPABILITIES at refresh
  KVM: VMX: Use proper type-safe functions for vCPU => LBRs helpers
  KVM: x86: Refresh PMU after writes to MSR_IA32_PERF_CAPABILITIES
  KVM: selftests: Test all possible "invalid" PERF_CAPABILITIES.LBR_FMT vals
  KVM: selftests: Use getcpu() instead of sched_getcpu() in rseq_test
  KVM: selftests: Make rseq compatible with glibc-2.35
  KVM: Actually create debugfs in kvm_create_vm()
  KVM: Pass the name of the VM fd to kvm_create_vm_debugfs()
  KVM: Get an fd before creating the VM
  KVM: Shove vcpu stats_id init into kvm_vcpu_init()
  KVM: Shove vm stats_id init into kvm_create_vm()
  KVM: x86/mmu: Add sanity check that MMIO SPTE mask doesn't overlap gen
  KVM: x86/mmu: rename trace function name for asynchronous page fault
  KVM: x86/xen: Stop Xen timer before changing IRQ
  KVM: x86/xen: Initialize Xen timer only once
  KVM: SVM: Disable SEV-ES support if MMIO caching is disable
  KVM: x86/mmu: Fully re-evaluate MMIO caching when SPTE masks change
  KVM: x86: Tag kvm_mmu_x86_module_init() with __init
  ...

Jiri reports that linux-atm does not build without this header.
Bring it back. It's completely dead code but we can't break
the build for user space :(
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Fixes: 052e1f01 ("net: atm: remove support for ZeitNet ZN122x ATM devices")
Link: https://lore.kernel.org/all/8576aef3-37e4-8bae-bab5-08f82a78efd3@kernel.org/
Link: https://lore.kernel.org/r/20220810164547.484378-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

We should trace the allocated address instead of page struct.

Fixes: 27c87486 ("dpaa2-eth: Use a single page per Rx buffer")
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20220811151651.3327-1-chen45464546@163.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge changes adding support for device properties with buffer values
to the ACPI device properties handling code.

* acpi-properties:
  ACPI: property: Fix error handling in acpi_init_properties()
  ACPI: property: Read buffer properties as integers
  ACPI: property: Add support for parsing buffer property UUID
  ACPI: property: Unify integer value reading functions
  ACPI: property: Switch node property referencing from ifs to a switch
  ACPI: property: Move property ref argument parsing into a new function
  ACPI: property: Use acpi_object_type consistently in property ref parsing
  ACPI: property: Tie data nodes to acpi handles
  ACPI: property: Return type of acpi_add_nondev_subnodes() should be bool

Multicast group flags were added in commit 4d54cc32 ("mptcp: avoid
lock_fast usage in accept path"), but it missed adding the kdoc.

Mention which flags go into that field, and do the same for
op structs.

Link: https://lore.kernel.org/r/20220809232012.403730-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull input updates from Dmitry Torokhov:

 - changes to input core to properly queue synthetic events (such as
   autorepeat) and to release multitouch contacts when an input device
   is inhibited or suspended

 - reworked quirk handling in i8042 driver that consolidates multiple
   DMI tables into one and adds several quirks for TUXEDO line of
   laptops

 - update to mt6779 keypad to better reflect organization of the
   hardware

 - changes to mtk-pmic-keys driver preparing it to handle more variants

 - facelift of adp5588-keys driver

 - improvements to iqs7222 driver

 - adjustments to various DT binding documents for input devices

 - other assorted driver fixes.

* tag 'input-for-v5.20-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
  Input: adc-joystick - fix ordering in adc_joystick_probe()
  dt-bindings: input: ariel-pwrbutton: use spi-peripheral-props.yaml
  Input: deactivate MT slots when inhibiting or suspending devices
  Input: properly queue synthetic events
  dt-bindings: input: iqs7222: Use central 'linux,code' definition
  Input: i8042 - add dritek quirk for Acer Aspire One AO532
  dt-bindings: input: gpio-keys: accept also interrupt-extended
  dt-bindings: input: gpio-keys: reference input.yaml and document properties
  dt-bindings: input: gpio-keys: enforce node names to match all properties
  dt-bindings: input: Convert adc-keys to DT schema
  dt-bindings: input: Centralize 'linux,input-type' definition
  dt-bindings: input: Use common 'linux,keycodes' definition
  dt-bindings: input: Centralize 'linux,code' definition
  dt-bindings: input: Increase maximum keycode value to 0x2ff
  Input: mt6779-keypad - implement row/column selection
  Input: mt6779-keypad - match hardware matrix organization
  Input: i8042 - add additional TUXEDO devices to i8042 quirk tables
  Input: goodix - switch use of acpi_gpio_get_*_resource() APIs
  Input: i8042 - add TUXEDO devices to i8042 quirk tables
  Input: i8042 - add debug output for quirks
  ...

area_cache_get() is used to distribute cache->area and set cache->id,
 and if cache->id is not 0 and cache->area->kref refcount is 0, it will
 release the cache->area by nfp_cpp_area_release(). area_cache_get()
 set cache->id before cpp->op->area_init() and nfp_cpp_area_acquire().

But if area_init() or nfp_cpp_area_acquire() fails, the cache->id is
 is already set but the refcount is not increased as expected. At this
 time, calling the nfp_cpp_area_release() will cause use-after-free.

To avoid the use-after-free, set cache->id after area_init() and
 nfp_cpp_area_acquire() complete successfully.

Note: This vulnerability is triggerable by providing emulated device
 equipped with specified configuration.

 BUG: KASAN: use-after-free in nfp6000_area_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:760)
  Write of size 4 at addr ffff888005b7f4a0 by task swapper/0/1

 Call Trace:
  <TASK>
 nfp6000_area_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:760)
 area_cache_get.constprop.8 (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:884)

 Allocated by task 1:
 nfp_cpp_area_alloc_with_name (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:303)
 nfp_cpp_area_cache_add (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:802)
 nfp6000_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:1230)
 nfp_cpp_from_operations (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:1215)
 nfp_pci_probe (drivers/net/ethernet/netronome/nfp/nfp_main.c:744)

 Freed by task 1:
 kfree (mm/slub.c:4562)
 area_cache_get.constprop.8 (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:873)
 nfp_cpp_read (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:924 drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:973)
 nfp_cpp_readl (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cpplib.c:48)
Signed-off-by: Jialiang Wang <wangjialiang0806@163.com>
Reviewed-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220810073057.4032-1-wangjialiang0806@163.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Change my address for mt7601u to the main one.

Link: https://lore.kernel.org/r/20220809233843.408004-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Drop devl_lock() / devl_unlock() from ports creation and removal flows
since the devlink instance lock is now taken by mlxsw_core.

Fixes: 72a4c8c9 ("mlxsw: convert driver to use unlocked devlink API during init/fini")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/f4afce5ab0318617f3866b85274be52542d59b32.1660211614.git.petrm@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit d5410ac7 ("net:bonding:support balance-alb interface
with vlan to bridge") introduced a reference count leak by not releasing
the reference acquired by ip_dev_find().  Remedy this by insuring the
reference is released.

Fixes: d5410ac7 ("net:bonding:support balance-alb interface with vlan to bridge")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/26758.1660194413@famineSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 258fafcd.

The clang -Wformat warning is terminally broken, and the clang people
can't seem to get their act together.

This test program causes a warning with clang:

	#include <stdio.h>

	int main(int argc, char **argv)
	{
		printf("%hhu\n", 'a');
	}

resulting in

  t.c:5:19: warning: format specifies type 'unsigned char' but the argument has type 'int' [-Wformat]
          printf("%hhu\n", 'a');
                  ~~~~     ^~~
                  %d

and apparently clang people consider that a feature, because they don't
want to face the reality of how either C character constants, C
arithmetic, and C varargs functions work.

The rest of the world just shakes their head at that kind of
incompetence, and turns off -Wformat for clang again.

And no, the "you should use a pointless cast to shut this up" is not a
valid answer.  That warning should not exist in the first place, or at
least be optinal with some "-Wformat-me-harder" kind of option.

[ Admittedly, there's also very little reason to *ever* use '%hh[ud]' in
  C, but what little reason there is is entirely about 'I want to see
  only the low 8 bits of the argument'. So I would suggest nobody ever
  use that format in the first place, but if they do, the clang
  behavious is simply always wrong. Because '%hhu' takes an 'int'. It's
  that simple. ]
Reported-by: Sudip Mukherjee (Codethink) <sudipm.mukherjee@gmail.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There are 2 models for MV32 serials. MV32-W-A is designed
based on Qualcomm SDX62 chip, and MV32-W-B is designed based
on Qualcomm SDX65 chip. So we use 2 different PID to separate it.

Test evidence as below:
T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=03 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1e2d ProdID=00f3 Rev=05.04
S:  Manufacturer=Cinterion
S:  Product=Cinterion PID 0x00F3 USB Mobile Broadband
S:  SerialNumber=d7b4be8d
C:  #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=03 Dev#= 10 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1e2d ProdID=00f4 Rev=05.04
S:  Manufacturer=Cinterion
S:  Product=Cinterion PID 0x00F4 USB Mobile Broadband
S:  SerialNumber=d095087d
C:  #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20220810014521.9383-1-slark_xiao@163.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull in bpf to silence a false positive warning.

* git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  bpf: Shut up kern_sys_bpf warning.

Link: https://lore.kernel.org/r/CAADnVQK589CZN1Q9w8huJqkEyEed+ZMTWqcpA1Rm2CjN3a4XoQ@mail.gmail.com/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Shut up this warning:
kernel/bpf/syscall.c:5089:5: warning: no previous prototype for function 'kern_sys_bpf' [-Wmissing-prototypes]
int kern_sys_bpf(int cmd, union bpf_attr *attr, unsigned int size)
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

There is unexpected warning on KVM_CAP_VM_DISABLE_NX_HUGE_PAGES capability
table, which cause the table to be rendered as paragraph text instead.

The warning is due to missing colon at capability name and returns keyword,
as well as improper alignment on multi-line returns field.

Fix the warning by adding missing colons and aligning the field.

Link: https://lore.kernel.org/lkml/20220627181937.3be67263@canb.auug.org.au/
Fixes: 084cc29f ("KVM: x86/MMU: Allow NX huge pages to be disabled on a per-vm basis")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: David Matlack <dmatlack@google.com>
Cc: Ben Gardon <bgardon@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-next@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Message-Id: <20220627095151.19339-3-bagasdotme@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Extend heading underline for KVM_CAP_VM_DISABLE_NX_HUGE_PAGE to match
the heading text length.

Link: https://lore.kernel.org/lkml/20220627181937.3be67263@canb.auug.org.au/
Fixes: 084cc29f ("KVM: x86/MMU: Allow NX huge pages to be disabled on a per-vm basis")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: David Matlack <dmatlack@google.com>
Cc: Ben Gardon <bgardon@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-next@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Message-Id: <20220627095151.19339-2-bagasdotme@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Currently, tls_device_down synchronizes with tls_device_resync_rx using
RCU, however, the pointer to netdev is stored using WRITE_ONCE and
loaded using READ_ONCE.

Although such approach is technically correct (rcu_dereference is
essentially a READ_ONCE, and rcu_assign_pointer uses WRITE_ONCE to store
NULL), using special RCU helpers for pointers is more valid, as it
includes additional checks and might change the implementation
transparently to the callers.

Mark the netdev pointer as __rcu and use the correct RCU helpers to
access it. For non-concurrent access pass the right conditions that
guarantee safe access (locks taken, refcount value). Also use the
correct helper in mlx5e, where even READ_ONCE was missing.

The transition to RCU exposes existing issues, fixed by this commit:

1. bond_tls_device_xmit could read netdev twice, and it could become
NULL the second time, after the NULL check passed.

2. Drivers shouldn't stop processing the last packet if tls_device_down
just set netdev to NULL, before tls_dev_del was called. This prevents a
possible packet drop when transitioning to the fallback software mode.

Fixes: 89df6a81 ("net/bonding: Implement TLS TX device offload")
Fixes: c55dcdd4 ("net/tls: Fix use-after-free after the TLS device goes down and up")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Link: https://lore.kernel.org/r/20220810081602.1435800-1-maximmi@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Another device offload bug, we use the length of the output
skb as an indication of how much data to copy. But that skb
is sized to offset + record length, and we start from offset.
So we end up double-counting the offset which leads to
skb_copy_bits() returning -EFAULT.
Reported-by: Tariq Toukan <tariqt@nvidia.com>
Fixes: 84c61fe1 ("tls: rx: do not use the standard strparser")
Tested-by: Ran Rozenstein <ranro@nvidia.com>
Link: https://lore.kernel.org/r/20220809175544.354343-2-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>