In some situations, we need to disable TSO on bonding slaves.

bonding device automatically unset TSO in bond_fix_features(), and
performance is not good because :

1) We consume more cpu cycles.

2) GSO segmentation has some bugs leading to out of order TCP packets
if this segmentation is done before virtual device. This particular
problem will be addressed in a separate patch.

This patch allows TSO being set/unset on the bonding master,
so that GSO segmentation is done after bonding layer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the interface is shutdown, the mv643xx_eth driver hits the following
lockdep dump:

=================================
[ INFO: inconsistent lock state ]
3.8.0+ #303 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
NetworkManager/3449 [HC0[0]:SC0[0]:HE1:SE1] takes:
 (_xmit_ETHER#2){+.?...}, at: [<c02828e4>] txq_reclaim+0x60/0x230
{IN-SOFTIRQ-W} state was registered at:
  [<c007e93c>] mark_irqflags+0xf8/0x1c4
  [<c007ee60>] __lock_acquire+0x458/0x9a4
  [<c007f8b0>] lock_acquire+0x60/0x74
  [<c03ea914>] _raw_spin_lock+0x40/0x50
  [<c0334040>] sch_direct_xmit+0xa4/0x2e4
  [<c0320880>] dev_queue_xmit+0x174/0x508
  [<c03953b0>] ip6_finish_output2+0xd0/0x3c4
  [<c03b15bc>] mld_sendpack+0x190/0x368
  [<c03b3204>] mld_ifc_timer_expire+0xc/0x58
  [<c005133c>] call_timer_fn+0x6c/0xe0
  [<c0051588>] run_timer_softirq+0x1d8/0x210
  [<c004c004>] __do_softirq+0xe0/0x1b4
  [<c004c448>] irq_exit+0x64/0x6c
  [<c000f1e0>] handle_IRQ+0x34/0x84
  [<c000e0d0>] __irq_usr+0x30/0x80
irq event stamp: 160603
hardirqs last  enabled at (160603): [<c00c736c>] kfree+0xa8/0xe8
hardirqs last disabled at (160602): [<c00c72e0>] kfree+0x1c/0xe8
softirqs last  enabled at (160304): [<c028260c>] mib_counters_update+0x5ec/0x60c
softirqs last disabled at (160302): [<c03eab8c>] _raw_spin_lock_bh+0x14/0x54

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(_xmit_ETHER#2);
  <Interrupt>
    lock(_xmit_ETHER#2);

 *** DEADLOCK ***

1 lock held by NetworkManager/3449:
 #0:  (rtnl_mutex){+.+.+.}, at: [<c032e664>] rtnetlink_rcv+0xc/0x24

stack backtrace:
[<c0013e34>] (unwind_backtrace+0x0/0xf8) from [<c007e12c>] (print_usage_bug+0x150/0x1d4)
[<c007e12c>] (print_usage_bug+0x150/0x1d4) from [<c007e3f8>] (mark_lock_irq+0x248/0x290)
[<c007e3f8>] (mark_lock_irq+0x248/0x290) from [<c007e598>] (mark_lock+0x158/0x404)
[<c007e598>] (mark_lock+0x158/0x404) from [<c007e97c>] (mark_irqflags+0x138/0x1c4)
[<c007e97c>] (mark_irqflags+0x138/0x1c4) from [<c007ee60>] (__lock_acquire+0x458/0x9a4)
[<c007ee60>] (__lock_acquire+0x458/0x9a4) from [<c007f8b0>] (lock_acquire+0x60/0x74)
[<c007f8b0>] (lock_acquire+0x60/0x74) from [<c03ea914>] (_raw_spin_lock+0x40/0x50)
[<c03ea914>] (_raw_spin_lock+0x40/0x50) from [<c02828e4>] (txq_reclaim+0x60/0x230)
[<c02828e4>] (txq_reclaim+0x60/0x230) from [<c0282ad8>] (txq_deinit+0x24/0xcc)
[<c0282ad8>] (txq_deinit+0x24/0xcc) from [<c0282d28>] (mv643xx_eth_stop+0x1a8/0x1bc)
[<c0282d28>] (mv643xx_eth_stop+0x1a8/0x1bc) from [<c031e314>] (__dev_close_many+0x88/0xcc)
[<c031e314>] (__dev_close_many+0x88/0xcc) from [<c031e380>] (__dev_close+0x28/0x3c)
[<c031e380>] (__dev_close+0x28/0x3c) from [<c0320fa0>] (__dev_change_flags+0x7c/0x134)
[<c0320fa0>] (__dev_change_flags+0x7c/0x134) from [<c03210e0>] (dev_change_flags+0x10/0x48)
[<c03210e0>] (dev_change_flags+0x10/0x48) from [<c032da1c>] (do_setlink+0x1a0/0x730)
[<c032da1c>] (do_setlink+0x1a0/0x730) from [<c032f524>] (rtnl_newlink+0x304/0x4b0)
[<c032f524>] (rtnl_newlink+0x304/0x4b0) from [<c032ef8c>] (rtnetlink_rcv_msg+0x25c/0x2a0)
[<c032ef8c>] (rtnetlink_rcv_msg+0x25c/0x2a0) from [<c03383a0>] (netlink_rcv_skb+0xbc/0xd8)
[<c03383a0>] (netlink_rcv_skb+0xbc/0xd8) from [<c032e674>] (rtnetlink_rcv+0x1c/0x24)
[<c032e674>] (rtnetlink_rcv+0x1c/0x24) from [<c03361d8>] (netlink_unicast_kernel+0x88/0xd4)
[<c03361d8>] (netlink_unicast_kernel+0x88/0xd4) from [<c0337dd0>] (netlink_unicast+0x138/0x180)
[<c0337dd0>] (netlink_unicast+0x138/0x180) from [<c0338020>] (netlink_sendmsg+0x208/0x32c)
[<c0338020>] (netlink_sendmsg+0x208/0x32c) from [<c030ab48>] (sock_sendmsg+0x84/0xa4)
[<c030ab48>] (sock_sendmsg+0x84/0xa4) from [<c030aef4>] (__sys_sendmsg+0x2ac/0x2c4)
[<c030aef4>] (__sys_sendmsg+0x2ac/0x2c4) from [<c030c8ec>] (sys_sendmsg+0x3c/0x68)
[<c030c8ec>] (sys_sendmsg+0x3c/0x68) from [<c000e2e0>] (ret_fast_syscall+0x0/0x3c)

It seems that txq_reclaim() takes the netif tx lock:

        __netif_tx_lock(nq, smp_processor_id());

in a context outside of softirq context, and thus is susceptible to
deadlock should an interrupt occur.

Use __netif_tx_lock_bh()/__netif_tx_unlock_bh() instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

GSO TCP handler has following issues :

1) ooo_okay from original GSO packet is duplicated to all segments
2) segments (but the last one) are orphaned, so transmit path can not
get transmit queue number from the socket. This happens if GSO
segmentation is done before stacked device for example.

Result is we can send packets from a given TCP flow to different TX
queues (if using multiqueue NICS). This generates OOO problems and
spurious SACK & retransmits.

Fix this by keeping socket pointer set for all segments.

This means that every segment must also have a destructor, and the
original gso skb truesize must be split on all segments, to keep
precise sk->sk_wmem_alloc accounting.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains three Netfilter fixes and update
for the MAINTAINER file for your net tree, they are:

* Fix crash if nf_log_packet is called from conntrack, in that case
  both interfaces are NULL, from Hans Schillstrom. This bug introduced
  with the logging netns support in the previous merge window.

* Fix compilation of nf_log and nf_queue without CONFIG_PROC_FS,
  from myself. This bug was introduced in the previous merge window
  with the new netns support for the netfilter logging infrastructure.

* Fix possible crash in xt_TCPOPTSTRIP due to missing sanity
  checkings to validate that the TCP header is well-formed, from
  myself. I can find this bug in 2.6.25, probably it's been there
  since the beginning. I'll pass this to -stable.

* Update MAINTAINER file to point to new nf trees at git.kernel.org,
  remove Harald and use M: instead of P: (now obsolete tag) to
  keep Jozsef in the list of people.

Please, consider pulling this. Thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This target assumes that tcph->doff is well-formed, that may be well
not the case. Add extra sanity checkings to avoid possible crash due
to read/write out of the real packet boundary. After this patch, the
default action on malformed TCP packets is to drop them. Moreover,
fragments are skipped.
Reported-by: Rafal Kupka <rkupka@telemetry.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

include/linux/brcmphy.h is currently not protected against double
inclusion, add ifdefs guard to fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 54309fa6 ("net: fec: fix kernel oops when plug/unplug cable many times")
introduced the following 'if' block in the beginning of fec_start():

	if (netif_running(ndev)) {
		netif_device_detach(ndev);
		napi_disable(&fep->napi);
		netif_stop_queue(ndev);
		netif_tx_lock_bh(ndev);
	}

Then later in the end of fec_restart() there is another block that calls the
opposite of each one of these functions.

The correct approach would be to also call them with in the reverse order, so
that we have as result:

	if (netif_running(ndev)) {
		netif_tx_unlock_bh(ndev);
		netif_wake_queue(ndev);
		napi_enable(&fep->napi);
		netif_device_attach(ndev);
	}
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fec_restart() runs in softirq context and we should use the
netif_tx_lock_bh/netif_tx_unlock_bh() variants to avoid the following warning
that happens since commit 54309fa6 ("net: fec: fix kernel oops when plug/unplug
cable many times"):

[    9.753168] =================================
[    9.757540] [ INFO: inconsistent lock state ]
[    9.761921] 3.10.0-rc1-next-20130514 #13 Not tainted
[    9.766897] ---------------------------------
[    9.771264] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[    9.777288] swapper/0 [HC0[0]:SC1[3]:HE1:SE0] takes:
[    9.782261]  (_xmit_ETHER#2){+.?...}, at: [<c03c24a4>] sch_direct_xmit+0xa0/0x2d4
[    9.789879] {SOFTIRQ-ON-W} state was registered at:
[    9.794769]   [<c0059c60>] __lock_acquire+0x528/0x1bc0
[    9.799953]   [<c005b838>] lock_acquire+0xa0/0x108
[    9.804780]   [<c0441320>] _raw_spin_lock+0x28/0x38
[    9.809702]   [<c02f9fc8>] fec_restart+0x5d0/0x664
[    9.814542]   [<c02fa738>] fec_enet_adjust_link+0xa8/0xc0
[    9.819978]   [<c02f7a28>] phy_state_machine+0x2fc/0x370
[    9.825323]   [<c0035ee0>] process_one_work+0x1c0/0x4a0
[    9.830589]   [<c0036594>] worker_thread+0x138/0x394
[    9.835587]   [<c003c620>] kthread+0xa4/0xb0
[    9.839890]   [<c000e820>] ret_from_fork+0x14/0x34
[    9.844728] irq event stamp: 185984
[    9.848226] hardirqs last  enabled at (185984): [<c00232b0>] local_bh_enable_ip+0x84/0xf0
[    9.856450] hardirqs last disabled at (185983): [<c0023270>] local_bh_enable_ip+0x44/0xf0
[    9.864667] softirqs last  enabled at (185966): [<c0023470>] irq_enter+0x64/0x68
[    9.872099] softirqs last disabled at (185967): [<c0023510>] irq_exit+0x9c/0xd8
[    9.879440]
[    9.879440] other info that might help us debug this:
[    9.885981]  Possible unsafe locking scenario:
[    9.885981]
[    9.891912]        CPU0
[    9.894364]        ----
[    9.896814]   lock(_xmit_ETHER#2);
[    9.900259]   <Interrupt>
[    9.902884]     lock(_xmit_ETHER#2);
[    9.906500]
[    9.906500]  *** DEADLOCK ***
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bug here is this code from ipg_nic_hard_start_xmit():

	txfd->tfc &= cpu_to_le64(~IPG_TFC_TFDDONE);

IPG_TFC_TFDDONE is 0x0000000080000000 so it's an unsigned int.  The
negated value is 0x7fffffff but 0xffffffff7fffffff was intended.

The other values in this file don't need to be changed but I did it for
consistency.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since (69b34fb9 netfilter: xt_LOG: add net namespace support
for xt_LOG), we hit this:

[ 4224.708977] BUG: unable to handle kernel NULL pointer dereference at 0000000000000388
[ 4224.709074] IP: [<ffffffff8147f699>] ipt_log_packet+0x29/0x270

when callling log functions from conntrack both in and out
are NULL i.e. the net pointer is invalid.

Adding struct net *net in call to nf_logfn() will secure that
there always is a vaild net ptr.

Reported as netfilter's bugzilla bug 818:
https://bugzilla.netfilter.org/show_bug.cgi?id=818Reported-by: Ronald <ronald645@gmail.com>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Commit 749a2b66 (net/macb: clear tx/rx completion flags in ISR)
introduces clear-on-write on ISR register. This behavior is not always
implemented when using Cadence MACB/GEM and is breaking other platforms.
We are using the Design Configuration Register 1 information and a capability
property to actually activate this clear-on-write behavior on ISR.
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Hein Tibosch <hein_tibosch@yahoo.es>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit fb745e9a ("net/802/mrp: fix possible race condition when
calling mrp_pdu_queue()") introduced a lockdep splat.

[   19.735147] =================================
[   19.735235] [ INFO: inconsistent lock state ]
[   19.735324] 3.9.2-build-0063 #4 Not tainted
[   19.735412] ---------------------------------
[   19.735500] inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
[   19.735592] rmmod/1840 [HC0[0]:SC0[0]:HE1:SE1] takes:
[   19.735682]  (&(&app->lock)->rlock#2){+.?...}, at: [<f862bb5b>]
mrp_uninit_applicant+0x69/0xba [mrp]

app->lock is normally taken under softirq context, so disable BH to
avoid the splat.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ward <david.ward@ll.mit.edu>
Cc: Cong Wang <amwang@redhat.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

3.10-rc1 issues the following warning:

netif_napi_add() called with weight 128 on device eth%d

This patch reduce the weight to 64, using NAPI_POLL_WEIGHT.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP md5 communications fail [1] for some devices, because sg/crypto code
assume page offsets are below PAGE_SIZE.

This was discovered using mlx4 driver [2], but I suspect loopback
might trigger the same bug now we use order-3 pages in tcp_sendmsg()

[1] Failure is giving following messages.

huh, entered softirq 3 NET_RX ffffffff806ad230 preempt_count 00000100,
exited with 00000101?

[2] mlx4 driver uses order-2 pages to allocate RX frags
Reported-by: Matt Schnall <mischnal@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Bernhard Beck <bbeck@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix to avoid double insertion of  vlan tags into the packet while
handling an asic workaroud (issue introduced by net next Commit bc0c3405)
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

efx_start_datapath() asserts that we can fit 2 RX scatter buffers plus
a software structure, each appropriately aligned, into a single page.
Where L1_CACHE_BYTES == 256 and PAGE_SIZE == 4096, which is the case
on s390, this assertion fails.

The current scatter buffer size is also not a multiple of 64 or 128,
which are more common cache line sizes.  If we can make both the start
and end of a scatter buffer cache-aligned, this will reduce the need
for read-modify-write operations on inter- processor links.

Fix the alignment by reducing EFX_RX_USR_BUF_SIZE to 2048 - 256 ==
1792.  (We could use 2048 - L1_CACHE_BYTES, but EFX_RX_USR_BUF_SIZE
also affects user-level networking where a larger amount of
housekeeping data may be needed.  Although this version of the driver
does not support user-level networking, I prefer to keep scattering
behaviour consistent with the out-of-tree version.)

This still doesn't fix the s390 build because like most architectures
it has NET_IP_ALIGN == 2.  When NET_IP_ALIGN != 0 we cannot achieve
cache line alignment at either the start or end of a scatter buffer,
so there is actually no point in padding the buffers to a multiple of
the cache line size.  All we need is 4-byte alignment of the network
header, so do that.

Adjust the assertions accordingly.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The two architectures that define CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
(powerpc and x86) now both define NET_IP_ALIGN as 0, so there is no
need for this optimisation any more.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 5725 family of devices (asic rev 5762), corrupts TSO packets where
the buffer is within MSS bytes of a 4G boundary (4G, 8G etc.). Detect
this condition and trigger the workaround path.

Cc: <stable@vger.kernel.org>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On the 5718, 5719 and 5720 serdes devices, powering down function 0
results in all the other ports being powered down. Add code to skip
function 0 power down.

v2:
 - Modify tg3_phy_power_bug() function to use a switch instead of a
   complicated if statement. Suggested by Joe Perches.

Cc: <stable@vger.kernel.org>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:
 "Several small bug fixes all over:

   1) be2net driver uses wrong payload length when submitting MAC list
      get requests to the chip.  From Sathya Perla.

   2) Fix mwifiex memory leak on driver unload, from Amitkumar Karwar.

   3) Prevent random memory access in batman-adv, from Marek Lindner.

   4) batman-adv doesn't check for pskb_trim_rcsum() errors, also from
      Marek Lindner.

   5) Fix fec crashes on rapid link up/down, from Frank Li.

   6) Fix inner protocol grovelling in GSO, from Pravin B Shelar.

   7) Link event validation fix in qlcnic from Rajesh Borundia.

   8) Not all FEC chips can support checksum offload, fix from Shawn
      Guo.

   9) EXPORT_SYMBOL + inline doesn't make any sense, from Denis Efremov.

  10) Fix race in passthru mode during device removal in macvlan, from
      Jiri Pirko.

  11) Fix RCU hash table lookup socket state race in ipv6, leading to
      NULL pointer derefs, from Eric Dumazet.

  12) Add several missing HAS_DMA kconfig dependencies, from Geert
      Uyttterhoeven.

  13) Fix bogus PCI resource management in 3c59x driver, from Sergei
      Shtylyov.

  14) Fix info leak in ipv6 GRE tunnel driver, from Amerigo Wang.

  15) Fix device leak in ipv6 IPSEC policy layer, from Cong Wang.

  16) DMA mapping leak fix in qlge from Thadeu Lima de Souza Cascardo.

  17) Missing iounmap on probe failure in bna driver, from Wei Yongjun."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
  bna: add missing iounmap() on error in bnad_init()
  qlge: fix dma map leak when the last chunk is not allocated
  xfrm6: release dev before returning error
  ipv6,gre: do not leak info to user-space
  virtio_net: use default napi weight by default
  emac: Fix EMAC soft reset on 460EX/GT
  3c59x: fix PCI resource management
  caif: CAIF_VIRTIO should depend on HAS_DMA
  net/ethernet: MACB should depend on HAS_DMA
  net/ethernet: ARM_AT91_ETHER should depend on HAS_DMA
  net/wireless: ATH9K should depend on HAS_DMA
  net/ethernet: STMMAC_ETH should depend on HAS_DMA
  net/ethernet: NET_CALXEDA_XGMAC should depend on HAS_DMA
  ipv6: do not clear pinet6 field
  macvlan: fix passthru mode race between dev removal and rx path
  ipv4: ip_output: remove inline marking of EXPORT_SYMBOL functions
  net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode
  net/mlx4_core: Add missing report on VST and spoof-checking dev caps
  net: fec: enable hardware checksum only on imx6q-fec
  qlcnic: Fix validation of link event command.
  ...

Add the missing iounmap() before return from bnad_init()
in the error handling case.
Introduced by commit 01b54b14
(bna: tx rx cleanup fix).
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge allocates chunks from a page that it maps and unmaps that page when
the last chunk is released. When the driver is unloaded or the card is
removed, all chunks are released and the page is unmapped for the last
chunk.

However, when the last chunk of a page is not allocated and the device
is removed, that page is not unmapped. In fact, its last reference is
not put and there's also a page leak. This bug prevents a device from
being properly hotplugged.

When the DMA API debug option is enabled, the following messages show
the pending DMA allocation after we remove the driver.

This patch fixes the bug by unmapping and putting the page from the ring
if its last chunk has not been allocated.

pci 0005:98:00.0: DMA-API: device driver has pending DMA allocations while released from device [count=1]
One of leaked entries details: [device address=0x0000000060a80000] [size=65536 bytes] [mapped with DMA_FROM_DEVICE] [mapped as page]
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:746
Modules linked in: qlge(-) rpadlpar_io rpaphp pci_hotplug fuse [last unloaded: qlge]
NIP: c0000000003fc3ec LR: c0000000003fc3e8 CTR: c00000000054de60
REGS: c0000003ee9c74e0 TRAP: 0700   Tainted: G           O  (3.7.2)
MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI>  CR: 28002424  XER: 00000001
SOFTE: 1
CFAR: c0000000007a39c8
TASK = c0000003ee8d5c90[8406] 'rmmod' THREAD: c0000003ee9c4000 CPU: 31
GPR00: c0000000003fc3e8 c0000003ee9c7760 c000000000c789f8 00000000000000ee
GPR04: 0000000000000000 00000000000000ef 0000000000004000 0000000000010000
GPR08: 00000000000000be c000000000b22088 c000000000c4c218 00000000007c0000
GPR12: 0000000028002422 c00000000ff26c80 0000000000000000 000001001b0f1b40
GPR16: 00000000100cb9d8 0000000010093088 c000000000cdf910 0000000000000001
GPR20: 0000000000000000 c000000000dbfc00 0000000000000000 c000000000dbfb80
GPR24: c0000003fafc9d80 0000000000000001 000000000001ff80 c0000003f38f7888
GPR28: c000000000ddfc00 0000000000000400 c000000000bd7790 c000000000ddfb80
NIP [c0000000003fc3ec] .dma_debug_device_change+0x22c/0x2b0
LR [c0000000003fc3e8] .dma_debug_device_change+0x228/0x2b0
Call Trace:
[c0000003ee9c7760] [c0000000003fc3e8] .dma_debug_device_change+0x228/0x2b0 (unreliable)
[c0000003ee9c7840] [c00000000079a098] .notifier_call_chain+0x78/0xf0
[c0000003ee9c78e0] [c0000000000acc20] .__blocking_notifier_call_chain+0x70/0xb0
[c0000003ee9c7990] [c0000000004a9580] .__device_release_driver+0x100/0x140
[c0000003ee9c7a20] [c0000000004a9708] .driver_detach+0x148/0x150
[c0000003ee9c7ac0] [c0000000004a8144] .bus_remove_driver+0xc4/0x150
[c0000003ee9c7b60] [c0000000004aa58c] .driver_unregister+0x8c/0xe0
[c0000003ee9c7bf0] [c0000000004090b4] .pci_unregister_driver+0x34/0xf0
[c0000003ee9c7ca0] [d000000002231194] .qlge_exit+0x1c/0x34 [qlge]
[c0000003ee9c7d20] [c0000000000e36d8] .SyS_delete_module+0x1e8/0x290
[c0000003ee9c7e30] [c0000000000098d4] syscall_exit+0x0/0x94
Instruction dump:
7f26cb78 e818003a e87e81a0 e8f80028 e9180030 796b1f24 78001f24 7d6a5a14
7d2a002a e94b0020 483a7595 60000000 <0fe00000> 2fb80000 40de0048 80120050
---[ end trace 4294f9abdb01031d ]---
Mapped at:
 [<d000000002222f54>] .ql_update_lbq+0x384/0x580 [qlge]
 [<d000000002227bd0>] .ql_clean_inbound_rx_ring+0x300/0xc60 [qlge]
 [<d0000000022288cc>] .ql_napi_poll_msix+0x39c/0x5a0 [qlge]
 [<c0000000006b3c50>] .net_rx_action+0x170/0x300
 [<c000000000081840>] .__do_softirq+0x170/0x300
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Jitendra Kalsaria <Jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull spi updates from Mark Brown:
 "A few driver specific fixes plus improved error handling in the
  generic DT GPIO chipselect handling - not exciting but useful."

* tag 'spi-v3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi/spi-atmel: BUG: fix doesn' support 16 bits transfers using PIO
  spi/davinci: fix module build error
  spi: Return error from of_spi_register_master on bad "cs-gpios" property
  spi: Initialize cs_gpio and cs_gpios with -ENOENT
  spi/atmel: fix speed_hz check in atmel_spi_transfer()

Pull drm fixes from Dave Airlie:
 "Just a few straggling fixes I hoovered up, and an intel fixes pull
  from Daniel which fixes some regressions, and some mgag200 fixes from
  Matrox."

* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
  drm/mgag200: Fix framebuffer base address programming
  drm/mgag200: Convert counter delays to jiffies
  drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register
  drm/mgag200: Don't change unrelated registers during modeset
  drm: Only print a debug message when the polled connector has changed
  drm: Make the HPD status updates debug logs more readable
  drm: Use names of ioctls in debug traces
  drm: Remove pointless '-' characters from drm_fb_helper documentation
  drm: Add kernel-doc for drm_fb_helper_funcs->initial_config
  drm: refactor call to request_module
  drm: Don't prune modes loudly when a connector is disconnected
  drm: Add missing break in the command line mode parsing code
  drm/i915: clear the stolen fb before resuming
  Revert "drm/i915: Calculate correct stolen size for GEN7+"
  drm/i915: hsw: fix link training for eDP on port-A
  Revert "drm/i915: revert eDP bpp clamping code changes"
  drm: don't check modeset locks in panic handler
  drm/i915: Fix pipe enabled mask for pipe C in WM calculations
  drm/mm: fix dump table BUG
  drm/i915: Always normalize return timeout for wait_timeout_ioctl

Pull virtio/lguest fixes from Rusty Russell:
 "Missing license tag and some fallout from the lguest pagetable rework"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  lguest: clear cached last cpu when guest_set_pgd() called.
  Add missing module license tag to vring helpers.

Higher bits of the base address of framebuffers weren't being
programmed properly. This caused framebuffers that didn't happen to be
allocated at a low enough address to not be displayed properly.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Christopher Harvey <charvey@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The original line,
  WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp);
wrote tmp into MGA1064_PIX_CLK_CTL_CLK_DIS, where
MGA1064_PIX_CLK_CTL_CLK_DIS is an offset into
MGA1064_PIX_CLK_CTL. Change the line to write properly into
MGA1064_PIX_CLK_CTL. There were other chunks of code nearby that use
the same pattern (but work correctly), so this patch updates them all
to use this new (slightly more efficient) write pattern. The WREG_DAC
macro was causing the DAC_INDEX register to be set to the same value
twice. WREG8(DAC_DATA, foo) takes advantage of the fact that DAC_INDEX
is already at the value we want.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Registers in indices below 0x18 are totally unrelated to modesetting,
so don't write 0's, or anything else into them on modeset. Most of
these registers are hardware cursor related, so this existing code
interferes with hardware cursor development.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Instead of just printing "status updated from 1 to 2", make those enum
numbers immediately readable.

v2: Also patch output_poll_execute() (Daniel Vetter)
v3: Use drm_get_connector_status_name (Ville Syrjälä)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (for v1)
Signed-off-by: Dave Airlie <airlied@redhat.com>

We forget to call dev_put() on error path in xfrm6_fill_dst(),
its caller doesn't handle this.

Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a hole in struct ip6_tnl_parm2, so we have to
zero the struct on stack before copying it to user-space.

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
we warn drivers when they use napi weight higher than NAPI_POLL_WEIGHT,
but virtio_net still uses 128 by default. This patch makes its default
value to NAPI_POLL_WEIGHT.

Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix EMAC soft reset on 460EX/GT to select the right PHY clock source
before and after the soft reset.

EMAC with PHY should use the clock from PHY during soft reset.
EMAC without PHY should use the internal clock during soft reset.

PPC460EX/GT Embedded Processor Advanced User's Manual
section 28.10.1 Mode Register 0 (EMACx_MR0) states:
Note: The PHY must provide a TX Clk in order to perform a soft reset
of the EMAC. If none is present, select the internal clock
(SDR0_ETH_CFG[EMACx_PHY_CLK] = 1).
After a soft reset, select the external clock.

Without the fix, 460EX/GT-based boards with RGMII PHYs attached to
EMACs experience EMAC interrupt storm and system watchdog reset when
issuing "ifconfig eth0 down" + "ifconfig eth0 up" a few times.
The system enters endless loop of serving emac_irq() with EMACx_ISR
register stuck at value 0x10000000 (Rx parity error).

With the fix, the above issue is no longer observed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver wrongly claimed I/O ports at an address returned by pci_iomap() --
even if it was passed an MMIO address.  Fix this by claiming/releasing all PCI
resources in the PCI driver's probe()/remove() methods instead and get rid of
'must_free_region' flag weirdness (why would Cardbus claim anything for us?).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull tracing/kprobes update from Steven Rostedt:
 "The majority of these changes are from Masami Hiramatsu bringing
  kprobes up to par with the latest changes to ftrace (multi buffering
  and the new function probes).

  He also discovered and fixed some bugs in doing so.  When pulling in
  his patches, I also found a few minor bugs as well and fixed them.

  This also includes a compile fix for some archs that select the ring
  buffer but not tracing.

  I based this off of the last patch you took from me that fixed the
  merge conflict error, as that was the commit that had all the changes
  I needed for this set of changes."

* tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing/kprobes: Support soft-mode disabling
  tracing/kprobes: Support ftrace_event_file base multibuffer
  tracing/kprobes: Pass trace_probe directly from dispatcher
  tracing/kprobes: Increment probe hit-count even if it is used by perf
  tracing/kprobes: Use bool for retprobe checker
  ftrace: Fix function probe when more than one probe is added
  ftrace: Fix the output of enabled_functions debug file
  ftrace: Fix locking in register_ftrace_function_probe()
  tracing: Add helper function trace_create_new_event() to remove duplicate code
  tracing: Modify soft-mode only if there's no other referrer
  tracing: Indicate enabled soft-mode in enable file
  tracing/kprobes: Fix to increment return event probe hit-count
  ftrace: Cleanup regex_lock and ftrace_lock around hash updating
  ftrace, kprobes: Fix a deadlock on ftrace_regex_lock
  ftrace: Have ftrace_regex_write() return either read or error
  tracing: Return error if register_ftrace_function_probe() fails for event_enable_func()
  tracing: Don't succeed if event_enable_func did not register anything
  ring-buffer: Select IRQ_WORK