Support these transfer modes from the SPI layer by setting
the appropriate register bits before doing the transfer.

This was tested on the Marvell kirkwood SOC that uses this driver.
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The MSIOF hardware block is used in the SH Mobile series as well, so we
add it here.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

clk_get() no longer needs a character string for associating the right
clock as this is done via the device struct now.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

In order to avoid constantly allocating and deallocating there is a fixed
buffer which spi_write_then_read() uses for transfers, with an early error
check to ensure that the transfer fits within the buffer. This limits the
size of transfers to this size, currently max(32, SMP_CACHE_BYTES).

Since we can dynamically allocate and in fact already have a fallback
to do so when there is contention for the fixed buffer remove this
restriction and instead dynamically allocate a suitably sized buffer if
the transfer won't fit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This driver is obsolete and can't even be built anymore since the
platform it depends has been removed.

The STMP series is completely covered by the MXS platform these days, so
spi-mxs can be used instead.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Pull in the changes Mark has queued up for SPI

This patch add new driver for CLPS711X SPI master controller.
Due to platform limitations driver supports only 8 bit transfer mode.
Chip select control is handled via GPIO.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

linux/err.h was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix the below warning
drivers/spi/spi-omap2-mcspi.c:336:34: warning: symbol 'tx' shadows an earlier one
drivers/spi/spi-omap2-mcspi.c:327:12: originally declared here

So delete the u8 tx as it is assigned and not used(resigned afterwards).
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The current HSPI driver used automatic CS control, leading to CS
active for each byte transmitted. This patch changes the driver
to manual CS control, and ensures CS is active thoughout a whole
message. Additionally, it uses the cs_change field to determine
if CS is disabled between transfers in the message.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This will allow to use gpio for chip select with no modification in the
driver binding

When use the cs-gpios, the gpio number will be passed via the cs_gpio field
and the number of chip select will automatically increased with max(hw cs, gpio cs).

So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:

cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;

Then it should be configured so that num_chipselect = 4 with the
following mapping:

cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
[grant.likely: fixed up type of cs count so min() can do type checking]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Use a proper list iterator instead of an open-coded loop and remove a
superfluous list head initialisation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This patch makes a loop look cleaner by replacing a "break" and a "continue"
in its body by a single "if".
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

0384e90b ("spi/mcspi: allow configuration of pin directions") did what
it claimed to do the wrong way around. D0/D1 is configured as output by
*clearing* the bits in the conf registers, hence also breaking the
former default behaviour.

Fix this before that change is merged to mainline.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

NVIDIA's Tegra20 have the SPI (SFLASH) controller to
interface with spi flash device which is used for system
boot. Add the spi driver for this controller.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Pull networking fixes from David Miller:
 "Bug fixes galore, mostly in drivers as is often the case:

  1) USB gadget and cdc_eem drivers need adjustments to their frame size
     lengths in order to handle VLANs correctly.  From Ian Coolidge.

  2) TIPC and several network drivers erroneously call tasklet_disable
     before tasklet_kill, fix from Xiaotian Feng.

  3) r8169 driver needs to apply the WOL suspend quirk to more chipsets,
     fix from Cyril Brulebois.

  4) Fix multicast filters on RTL_GIGA_MAC_VER_35 r8169 chips, from
     Nathan Walp.

  5) FDB netlink dumps should use RTM_NEWNEIGH as the message type, not
     zero.  From John Fastabend.

  6) Fix smsc95xx tx checksum offload on big-endian, from Steve
     Glendinning.

  7) __inet_diag_dump() needs to repsect and report the error value
     returned from inet_diag_lock_handler() rather than ignore it.
     Otherwise if an inet diag handler is not available for a particular
     protocol, we essentially report success instead of giving an error
     indication.  Fix from Cyrill Gorcunov.

  8) When the QFQ packet scheduler sees TSO/GSO packets it does not
     handle things properly, and in fact ends up corrupting it's
     datastructures as well as mis-schedule packets.  Fix from Paolo
     Valente.

  9) Fix oopser in skb_loop_sk(), from Eric Leblond.

  10) CXGB4 passes partially uninitialized datastructures in to FW
      commands, fix from Vipul Pandya.

  11) When we send unsolicited ipv6 neighbour advertisements, we should
      send them to the link-local allnodes multicast address, as per
      RFC4861.  Fix from Hannes Frederic Sowa.

  12) There is some kind of bug in the usbnet's kevent deferral
      mechanism, but more immediately when it triggers an uncontrolled
      stream of kernel messages spam the log.  Rate limit the error log
      message triggered when this problem occurs, as sending thousands
      of error messages into the kernel log doesn't help matters at all,
      and in fact makes further diagnosis more difficult.

      From Steve Glendinning.

  13) Fix gianfar restore from hibernation, from Wang Dongsheng.

  14) The netlink message attribute sizes are wrong in the ipv6 GRE
      driver, it was using the size of ipv4 addresses instead of ipv6
      ones :-) Fix from Nicolas Dichtel."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  gre6: fix rtnl dump messages
  gianfar: ethernet vanishes after restoring from hibernation
  usbnet: ratelimit kevent may have been dropped warnings
  ipv6: send unsolicited neighbour advertisements to all-nodes
  net: usb: cdc_eem: Fix rx skb allocation for 802.1Q VLANs
  usb: gadget: g_ether: fix frame size check for 802.1Q
  cxgb4: Fix initialization of SGE_CONTROL register
  isdn: Make CONFIG_ISDN depend on CONFIG_NETDEVICES
  cxgb4: Initialize data structures before using.
  af-packet: fix oops when socket is not present
  pkt_sched: enable QFQ to support TSO/GSO
  net: inet_diag -- Return error code if protocol handler is missed
  net: bnx2x: Fix typo in bnx2x driver
  smsc95xx: fix tx checksum offload for big endian
  rtnetlink: Use nlmsg type RTM_NEWNEIGH from dflt fdb dump
  ptp: update adjfreq callback description
  r8169: allow multicast packets on sub-8168f chipset.
  r8169: Fix WoL on RTL8168d/8111d.
  drivers/net: use tasklet_kill in device remove/close process
  tipc: do not use tasklet_disable before tasklet_kill

Pull sparc fixes from David Miller:
 "Several build/bug fixes for sparc, including:

  1) Configuring a mix of static vs.  modular sparc64 crypto modules
     didn't work, remove an ill-conceived attempt to only have to build
     the device match table for these drivers once to fix the problem.

     Reported by Meelis Roos.

  2) Make the montgomery multiple/square and mpmul instructions actually
     usable in 32-bit tasks.  Essentially this involves providing 32-bit
     userspace with a way to use a 64-bit stack when it needs to.

  3) Our sparc64 atomic backoffs don't yield cpu strands properly on
     Niagara chips.  Use pause instruction when available to achieve
     this, otherwise use a benign instruction we know blocks the strand
     for some time.

  4) Wire up kcmp

  5) Fix the build of various drivers by removing the unnecessary
     blocking of OF_GPIO when SPARC.

  6) Fix unintended regression wherein of_address_to_resource stopped
     being provided.  Fix from Andreas Larsson.

  7) Fix NULL dereference in leon_handle_ext_irq(), also from Andreas
     Larsson."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix build with mix of modular vs. non-modular crypto drivers.
  sparc: Support atomic64_dec_if_positive properly.
  of/address: sparc: Declare of_address_to_resource() as an extern function for sparc again
  sparc32, leon: Check for existent irq_map entry in leon_handle_ext_irq
  sparc: Add sparc support for platform_get_irq()
  sparc: Allow OF_GPIO on sparc.
  qlogicpti: Fix build warning.
  sparc: Wire up sys_kcmp.
  sparc64: Improvde documentation and readability of atomic backoff code.
  sparc64: Use pause instruction when available.
  sparc64: Fix cpu strand yielding.
  sparc64: Make montmul/montsqr/mpmul usable in 32-bit threads.

Pull cifs fixes from Jeff Layton.

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Do not lookup hashed negative dentry in cifs_atomic_open
  cifs: fix potential buffer overrun in cifs.idmap handling code

Pull arm64 fixes from Catalin Marinas:
 - correct argument type (pgprot_t) when calling __ioremap()
 - PCI_IOBASE virtual address change
 - use architected event for CPU cycle counter
 - fix ELF core dumping
 - select CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION
 - missing completion for secondary CPU boot
 - booting on systems with all memory beyond 4GB

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  arm64: mm: fix booting on systems with no memory below 4GB
  arm64: smp: add missing completion for secondary boot
  arm64: compat: select CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION
  arm64: elf: fix core dumping definitions for GP and FP registers
  arm64: perf: use architected event for CPU cycle counter
  arm64: Move PCI_IOBASE closer to MODULES_VADDR
  arm64: Use pgprot_t as the last argument when invoking __ioremap()

Merge tag 'stable/for-linus-3.7-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen fixes from Konrad Rzeszutek Wilk:
 "There are three ARM compile fixes (we forgot to export certain
  functions and if the drivers are built as an module - we go belly-up).

  There is also an mismatch of irq_enter() / exit_idle() calls sequence
  which were fixed some time ago in other piece of codes, but failed to
  appear in the Xen code.

  Lastly a fix for to help in the field with troubleshooting in case we
  cannot get the appropriate parameter and also fallback code when
  working with very old hypervisors."

Bug-fixes:
 - Fix compile issues on ARM.
 - Fix hypercall fallback code for old hypervisors.
 - Print out which HVM parameter failed if it fails.
 - Fix idle notifier call after irq_enter.

* tag 'stable/for-linus-3.7-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/arm: Fix compile errors when drivers are compiled as modules (export more).
  xen/arm: Fix compile errors when drivers are compiled as modules.
  xen/generic: Disable fallback build on ARM.
  xen/events: fix RCU warning, or Call idle notifier after irq_enter()
  xen/hvm: If we fail to fetch an HVM parameter print out which flag it is.
  xen/hypercall: fix hypercall fallback code for very old hypervisors

We tried linking in a single built object to hold the device table,
but only works if all of the sparc64 crypto modules get built the same
way (modular vs. non-modular).

Just include the device ID stub into each driver source file so that
the table gets compiled into the correct result in all cases.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparc32 already supported it, as a consequence of using the
generic atomic64 implementation.  And the sparc64 implementation
is rather trivial.

This allows us to set ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE for all
of sparc, and avoid the annoying warning from lib/atomic64_test.c
Signed-off-by: David S. Miller <davem@davemloft.net>

This bug-fix makes sure that of_address_to_resource is defined extern for sparc
so that the sparc-specific implementation of of_address_to_resource() is once
again used when including include/linux/of_address.h in a sparc context. A
number of drivers in mainline relies on this function working for sparc.

The bug was introduced in a850a755, "of/address:
add empty static inlines for !CONFIG_OF". Contrary to that commit title, the
static inlines are added for !CONFIG_OF_ADDRESS, and CONFIG_OF_ADDRESS is never
defined for sparc. This is good behavior for the other functions in
include/linux/of_address.h, as the extern functions defined in
drivers/of/address.c only gets linked when OF_ADDRESS is configured. However,
for of_address_to_resource there exists a sparc-specific implementation in
arch/sparc/arch/sparc/kernel/of_device_common.c

Solution suggested by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If an irq is being unlinked concurrently with leon_handle_ext_irq,
irq_map[eirq] might be null in leon_handle_ext_irq. Make sure that
this is not dereferenced.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds sparc support for platform_get_irq that in the normal case use
platform_get_resource() to get an irq. This standard approach fails for sparc as
there are no resources of type IORESOURCE_IRQ for irqs for sparc.

Cross platform drivers can then use this standard platform function and work on
sparc instead of having to have a special case for sparc.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spotted after a code review.
Introduced by c12b395a (gre: Support GRE over
IPv6).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a gianfar ethernet device is down prior to hibernating a
system, it will no longer be present upon system restore.

For example:

	~# ifconfig eth0 down
	~# echo disk > /sys/power/state

	  <trigger a restore from hibernation>

	~# ifconfig eth0 up
	SIOCSIFFLAGS: No such device

This happens because the restore function bails out early upon
finding devices that were not up at hibernation.  In doing so,
it never gets to the netif_device_attach call at the end of
the restore function.  Adding the netif_device_attach as done
here also makes the gfar_restore code consistent with what is
done in the gfar_resume code.

Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

when something goes wrong, a flood of these messages can be
generated by usbnet (thousands per second).  This doesn't
generally *help* the condition so this patch ratelimits the
rate of their generation.

There's an underlying problem in usbnet's kevent deferral
mechanism which needs fixing, specifically that events *can*
get dropped and not handled.  This patch doesn't address this,
but just mitigates fallout caused by the current implemention.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

As documented in RFC4861 (Neighbor Discovery for IP version 6) 7.2.6.,
unsolicited neighbour advertisements should be sent to the all-nodes
multicast address.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm fixes (again) from Dave Airlie:
 "dropped the ball on a vmware patch, so two more fixes for vmwgfx are
  here, one for hibernate issue, one for a BUG trigger."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/vmwgfx: Fix a case where the code would BUG when trying to pin GMR memory
  drm/vmwgfx: Fix hibernation device reset

Pull PCI fixes from Bjorn Helgaas:
 "Power management:
    - PCI/PM: Fix proc config reg access for D3cold and bridge
      suspending
    - PCI/PM: Resume device before shutdown
    - PCI/PM: Fix deadlock when unbinding device if parent in D3cold
  Hotplug:
    -  PCI/portdrv: Don't create hotplug slots unless port supports
       hotplug"

* tag '3.7-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI/portdrv: Don't create hotplug slots unless port supports hotplug
  PCI/PM: Fix proc config reg access for D3cold and bridge suspending
  PCI/PM: Resume device before shutdown
  PCI/PM: Fix deadlock when unbinding device if parent in D3cold

Pull MMC fixes from Chris Ball:
 - sdhci: fix a NULL dereference at resume-time, seen on OLPC XO-4
 - sdhci: fix against 3.7-rc1 for UHS modes without a vqmmc regulator
 - sdhci-of-esdhc: disable CMD23 on boards where it's broken
 - sdhci-s3c: fix against 3.7-rc1 for card detection with runtime PM
 - dw_mmc, omap_hsmmc: fix potential NULL derefs, compiler warnings

* tag 'mmc-fixes-for-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: sdhci-s3c: fix the card detection in runtime-pm
  mmc: sdhci-s3c: use clk_prepare_enable and clk_disable_unprepare
  mmc: dw_mmc: constify dw_mci_idmac_ops in exynos back-end
  mmc: dw_mmc: fix modular build for exynos back-end
  mmc: sdhci: fix NULL dereference in sdhci_request() tuning
  mmc: sdhci: fix IS_ERR() checking of regulator_get()
  mmc: fix sdhci-dove probe/removal
  mmc: sh_mmcif: fix use after free
  mmc: sdhci-pci: fix 'Invalid iomem size' error message condition
  mmc: mxcmmc: Fix MODULE_ALIAS
  mmc: omap_hsmmc: fix NULL pointer dereference for dt boot
  mmc: omap_hsmmc: fix host reference after mmc_free_host
  mmc: dw_mmc: fix multiple drv_data NULL dereferences
  mmc: dw_mmc: enable controller interrupt before calling mmc_start_host
  mmc: sdhci-of-esdhc: disable CMD23 for some Freescale SoCs
  mmc: dw_mmc: remove _dev_info compile warning
  mmc: dw_mmc: convert the variable type of irq

Pull crypto fix from Herbert Xu:
 "This push fixes a potential panic in cryptd which may occur with
  crypto drivers such as aesni-intel."

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: cryptd - disable softirqs in cryptd_queue_worker to prevent data corruption

Pull sound fixes from Takashi Iwai:
 "Most of commits are for stable and regression fixes.  Except for one
  fix for a regression in 3.7-rc4, there are all driver local changes,
  so nothing too much to worry."

* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: Fix card refcount unbalance
  ALSA: hda - Add new codec ALC668 and ALC900 (default name ALC1150)
  ALSA: hda - Improve HP depop when system enter to S3
  ALSA: usb-audio: Fix crash at re-preparing the PCM stream
  ALSA: hdspm - Fix sync check reporting on RME RayDAT
  ALSA: hda - Add pin fixups for ASUS G75
  ALSA: hda - Fix invalid connections in VT1802 codec
  ALSA: hda - Fix empty DAC filling in patch_via.c
  ALSA: hda - Force to reset IEC958 status bits for AD codecs
  ALSA: es1968: Add ESS vendor ID to pm_whitelist
  ALSA: HDA: Mark CS260x immutable structures const
  ALSA: HDA: Fix digital microphone on CS420x
  ALSA: hda: Cirrus: Fix coefficient index for beep configuration
  ALSA: hda - support Teradici 2200 host card audio
  ALSA: Fix typo in drivers sound

Currently the master->setup() is called unconditionally.
The assumption is that every driver need to implement this
callback. This encourages drivers to populate empty functions
to prevent crashing.

This patch prevents the call of master->setup() if it is not
populated.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>